Omron HEM-907XL IntelliSense Instruction Manual

HIDE

P

-

SET

100

AUTO

140

180

220

260

280

MODE

AVG.

MANU.

CHECK

SINGLE

ON/OFF

A

V

G

.

/

1

s

t

/

2

n

d

/

3

r

d

D

E

F

L

A

T

I

O

N

START

STOP

mmHg

SYS

mmHg

DIA

BPM

PULSE

AC

ART.

INDEX

INDEX

MAX

MAX

X

L

®

IntelliSense®Blood Pressure Monitor

Model

HEM-907XL

Table of Contents

Be Sure to Read This Section

Exemptions ........................................2

Notes on Safety .................................3

Know Your Unit

Features of the Product .....................7

Components of the Product...............8

Options...........................................9

Features and Functions...................10

Names of the Parts ......................10

Functions and setting

while the unit is in use..................12

Preparations before Measurement

How to Apply the Cuff ......................14

How to Use the Power Source

........

16

How to Use the AC Adapter

............16

Installation and Replacement

of Battery Pack.............................17

How to Measure Blood Pressure

List of Measurement Modes ............19

SINGLE Mode ..............................20

AVG Mode....................................22

MANU Mode.................................24

How to Check Pressure Accuracy..26

How to Clean the Unit after Use

........

27

List of Error Codes...........................28

Troubleshooting................................29

Specifications

Caution.............................................30

Five Year Limited Warranty ..............31

Specifications

...................................

31

Thank you for purchasing the OMRON
IntelliSense

®

Blood Pressure Monitor.

Please thoroughly read this Instruction Manual
before using this monitor to ensure safe and
accurate use.

Please keep this manual near the monitor all
the time for future reference.

INSTRUCTION MANUAL

HEM-907XL Rev B 3/2/07 1:41 AM Page 1

2

EXEMPTIONS

OMRON does not accept liability and warranty becomes void under the following
circumstances:

1. When persons, not authorized by OMRON, perform repairs or modifications of this
product.

2. When use and/or operation of this device is adversely effected by a device not
manufactured by OMRON.

3. When use and/or operation of this device is adversely effected by use of parts, not
authorized by OMRON, to repair or modify this product.

4. When Notes on Safety or Instructions for Use contained in this manual are not followed.

5. When use and/or operation of this device is effected by an act of God, such as fire,
earthquake, flood or other natural disasters.

1. The product and contents of this Instruction Manual may be changed without prior notice.

2. We have prepared the contents of this Instruction Manual thoroughly. However, if an
inadequate description or error is found, please let us know.

3. Reproducing or copying any or all of this Instruction Manual without OMRON’s written
consent is prohibited.

HEM-907XL Rev B 3/2/07 1:41 AM Page 2

3

NOTES ON SAFETY

• The warning signs and the sample icons shown here are listed to insure safe and accurate use.

• The icons and meanings are as follows.

W

arning sign Contents

Indicates matters in which death or severe bodily damage may arise as a result
of incorrect handling.

Indicates matters in which bodily harm or material damage* may arise as a
result of incorrect handling.

* Material damage refers to a wide range of damage involving your house, household goods, domestic animals, and pets.

Examples of signs

The icon indicates caution (including warning and danger).
Matters involving actual caution are indicated by text or pictures in or near .
The pictured icon refers to "caution for flammability".

The icon indicates prohibitions (what you cannot do).
Matters involving actual prohibitions are indicated by text or pictures in or near .
The pictured icon refers to "prohibition to disassemble".

The icon indicates something that is compulsory (always follow).
Matters involving actual compulsory actions are indicated by text or pictures in or near .
The pictured icon refers to "unplugging the power source plug".

Do not wrap the cuff over an arm to which intravenous injection or transfusion
is being conducted, or when otherwise contraindicated.

Do not connect the air tube or the cuff to other equipment which is connected
to an intracorporeal organ. Air embolisms may result.

Self diagnosis of measured results or treatment is dangerous. Please follow
the instruction of the doctor or healthcare provider.

If cuff inflation does not stop, remove the cuff or pull out the air tube from the
main unit.

If battery fluid gets into your eye or comes in contact with skin, wash the effected
area with water repeatedly. Immediately consult a doctor for treatment.

Do not use this unit in the presence of flammable gas or anesthetics or in a
high pressure oxygen room or oxygen tent.

Do not use the battery pack for devices other than for this unit.
Do not disassemble the battery pack.

Do not touch the AC adapter with wet hands.

HEM-907XL Rev B 3/2/07 1:41 AM Page 3

4

NOTES ON SAFETY

Unplug the AC adapter from the electric outlet if this unit is unused for an
extended period of time.

Unplug the AC adapter from the electric outlet when installing, removing, or
cleaning the unit.

Confirm readings with a stethoscope when an irregular pulse wave is
displayed or when the measured value is questionable or erratic.

Use an AC adapter indicated for use with a power supply of 110 VAC.
Do not share an electric outlet with other unit or electric appliance.
After cleaning this unit, dry it well before plugging the AC adapter in the

electric outlet.
If this unit fails to perform as indicated, discontinue use, turn off the unit,

unplug the AC adapter from the electric outlet, and contact OMRON’s repair
department.

Do not disassemble or modify this unit.

Do not use any cuff other than the models exclusive for this unit.
Do not use this unit on infants.
Do not use this unit on patients using a pump oxygenator.
Do not use an AC adapter or battery pack not specified for this unit.

NOTES ON SAFETY

HEM-907XL Rev B 3/2/07 1:41 AM Page 4

5

NOTES ON SAFETY

Do not use a cellular phone near this unit.
Do not use this unit in a vehicle.
Do not install the parts and/or instruments not specified for this unit.
Do not use a broken power cord or AC adapter.

Do not install or store this unit where it may come in contact with water or
liquid medication.

This is a Class II device with double isolation. Earth pin is not for protective
purposes.

General advice

Do not place or put anything on this unit.
Do not drop this unit.
Turn off power to the unit and unplug the AC adapter from the electric outlet before moving

the unit.
Read the instruction manual of the other devices to be used at the same time with this unit, to

understand and be aware of the interaction between the devices.
When using the unit

• Do not inflate the cuff without being wrapped over the arm.

• Do not use a damaged cuff.

• Be sure that patients do not touch the Buttons of this unit.

After using the unit

• Do not disinfect this unit by autoclave or gas sterilization (EtO, gluteraldehyde, or high
concentration ozone).

Do not install or store this unit in the following places.

• Under the direct sunlight,

• Dusty or salty environment,

• Places having slope, vibration, and/or shock,

• Storage of chemicals or where combustable gas may be generated,

• Under high temperature and high humidity.

HEM-907XL Rev B 3/2/07 1:41 AM Page 5

6

NOTES ON SAFETY

Maintenance and inspection

1. Check the unit operation on regular basis.

2. If this unit has not been used for more than three months, be sure to check that this unit
operates normally and safely before use.

Troubleshooting

If device error 9 (Er9) occurs, take the following procedure promptly:
(1) Remove the cuff from the patient's arm.
(2) Turn off the power of the unit and unplug the AC adapter from the electric outlet.
(3) Display "Out of use" on this unit so that it cannot be used.
(4) Contact Omron Healthcare’s Customer Service at 1-877-216-1336.

HEM-907XL Rev B 3/2/07 1:41 AM Page 6

7

FEATURES OF THE PRODUCT

OMRON IntelliSense®Blood Pressure unit, Model HEM-907XL is developed to measure blood
pressure and pulse rate accurately and simply in a doctor's office, examination room,
or patient bedside.

• One-button operation

Simply wrap the cuff and push the START Button. Blood pressure and pulse rate are automatically
measured by the oscillometric method.

• Automatic pressure setting

When the P-SET (Pressure Setting) Knob is set to "AUTO," the unit will automatically inflate the
cuff to the optimal pressure according to each patient's blood pressure. Pre-setting inflation level
is not necessary.

• Noiseless operation

This unit operates so quietly that it can be used in the patient room at night.

• Average Mode (AVG Mode)

In the AVG Mode, this unit will automatically measure for two or three times. The average of
systolic and diastolic blood pressures and pulse rate are displayed. Each measurement can also
be shown individually. The number of measurements, waiting time before first measurement, and
the interval can be changed.

• Auscultation Mode (MANU Mode)

You can measure auscultatory blood pressure by using a stethoscope, with automatic cuff inflation
and deflation by this unit. Because the cuff pressures during deflation are displayed digitally and
synchronized with the heart beat, they can be read with accuracy. After taking systolic reading
you can accelerate cuff deflation to shorten measurement time.

• Large and easy to read display

Large and easy to read figures are displayed on the LCD display.

The IntelliSense

®

Monitor inflates the cuff to the ideal level with each use. No adjustments are
required by the user to select an inflation level. This is especially convenient for hypertensive users
and for people with certain arrhythmia or heart disorders, because their blood pressure is likely to
fluctuate. The advantage is Personalized Inflation for maximum comfort.

HEM-907XL Rev B 3/2/07 1:41 AM Page 7

8

COMPONENTS OF THE PRODUCT

XL

®

®

Main unit

Accessories

Air tube 1.0m (39 1/3") *

Model: HEM-TUBE-100X

AC adapter

Model: HEM-AC-J

Instruction Manual

Items identified with an asterisk (*) are consumables and not covered by the guarantee.

IntelliSense®Blood Pressure
Monitor, Model HEM-907XL

(Included and also available separately)

Cuff / bladder set Large
(with built-in bladder) *
Model: HEM-907-CL19
Applicable arm circumference:
13

" to 17" (

32 to 42 cm)

Cuf

f / bladder set Small
(with built-in bladder) *
Model: HEM-907-CS19
Applicable arm circumference:
7” to 9

" (

17 to 22 cm)

Cuff / bladder set Medium
(with built-in bladder) *
Model: HEM-907-CR19
Applicable arm circumference:
9

" to 13"

(22 to 32 cm)

Battery pack (48H907N)

Model: HEM-907-PBAT

The air tube is available for the
large, medium or small cuf

f size.
It is NOT for use with the
extra-large cuff size.

Cuff / bladder set Extra Large
(with built-in bladder) *
Model: HEM-907-CX19
For use with the HEM-907XL
unit only.
Applicable arm circumference:
17

" to 20" (

42 to 50 cm)

HEM-907XL Rev B 3/2/07 1:41 AM Page 8

9

COMPONENTS OF THE PRODUCT

Exclusive Stand
Model: HEM-907-STAND

W

all-hanging kit

Model: HEM-907-WKIT

Bladders *

Pole-mounting kit
Model: HEM-907-PKIT

Cuffs without bladder *

Options

Large Cuff
Model:HEM-907-CUFFL

Extra Large Cuff
For use with the
HEM-907XL only.
M

odel:HEM-907-CUFFX

Medium Cuff
Model: HEM-907-CUFFM

Small Cuff
Model: HEM-907-CUFFS

Large Bladder
Model: HEM-907-BLDRL

E

xtra Large Bladder
For use with the
HEM-907XL only.
Model: HEM-907-BLDRX

Medium Bladder
Model: HEM-907-BLDRM

Small Bladder
Model: HEM-907-BLDRS

Air tube 1.3 m (51 1/6")*
Model: HEM-TUBE-130

Items identified
with an asterisk (*)
are consumables
and not covered by
the guarantee.

Accessories and
options are subject
to change without
prior notice.

(not included)

The air tube is available for the large,
medium or small size cuff.
It is NOT for use with the extra-large
cuff size.

HEM-907XL Rev B 3/2/07 1:41 AM Page 9

10

FEATURES AND FUNCTIONS

Main unit

1.Display:

Displays blood pressure and, pulse rate readings, and oscillation pulse level.

2.HIDE Button: Switches display and non-display of measured results.

3.DC jack: Connects the AC adapter.

4.P-SET (pressure setting) Knob: In the AUTO position, inflation level is automatically set.

Otherwise, inflation level can optionally be set manually between 100 and 280 mmHg.

5.MODE Selector: Selects the operation mode.

•

One-time Measurement Mode (SINGLE Mode): Measurement with automatic inflation.

• Average Mode (AVG Mode): Automatically measures two (or three) times consecutively.

• Auscultation Mode (MANU Mode): Automatic inflation, automatic deflation, and pressure display for auscultation (does
not measure blood pressure).

• Check Mode (CHECK Mode): Checks the accuracy of pressure display. Displays only pressure.

6.ON/OFF (power) Button: Turns on or off the unit.

7.START Button: Starts the measurement.

8. DEFLATION (deflation control) /Measurement Result Display Switch Button:

• In the MANU Mode, deflates the cuff by approximately 5 to 10 mmHg with each push during deflation.

•

In the

A

VG Mode, switches the display of average values and the measurement results with each push.

9.Air Connector: Connects the air tube.

10.STOP Button: Stops the measurement and deflates air rapidly.

HIDE

P

-

SET

100

AUTO

140

180

220

260

280

MODE

AVG.

MANU.

CHECK

SINGLE

ON/OFF

A

V

G

.

/

1

s

t

/

2

n

d

/

3

r

d

D

E

F

L

A

T

I

O

N

START

STOP

mmHg

SYS

mmHg

DIA

BPM

P

U

L

S

E

AC

DC8V

X

L

®

1. Display

2. HIDE (non-display) Button

3. DC jack

4. P-SET (pressure
setting) Knob

5. MODE Selector

6. ON/OFF (power)
Button

7. START Button

8. DEFLATION
(deflation control)
/Measurement
Result Display
Switch Button

9. Air Connector

10. STOP Button

Names of the Parts

(See Page 11 for detail)

HEM-907XL Rev B 3/2/07 1:41 AM Page 10

11

FEATURES AND FUNCTIONS

Display

HIDE

BPM

mmHg

PULSE

SYS

mmHg

DIA

AC

Systolic blood pressure

Diastolic blood pressure

Pulse rate

Contents when the AVG
Mode is selected

A

VG.: Mean value
1st : First reading
2nd : Second reading
3rd

: Third reading

Ready to Measure /
Pulse synchronization

Pulse level /
Number of irregular pulses

Number of irregular pulse waves: The pulse
wave having a difference of more than 25%
from the average interval of pulse waves is
determined irregular. Number of irregular
pulse waves is displayed up to three times.

Battery level

Displays for the operable level.

Blinks for a low charged

level

Displays for the inoperable

level.

Charging

Displays when the battery
pack is being charged.

External power source

Displays AC when the unit is connected
to the external power source via the AC
adapter.

Example of display

No. of irregular pulses

123

HEM-907XL Rev B 3/2/07 1:41 AM Page 11

12

FEATURES AND FUNCTIONS

Functions setting

(1) Inflation level setting

AUTO (Automatic setting): Can be used when the SINGLE, AVG, or MANU Mode is selected.

The unit estimates the systolic blood pressure during inflation and inflates to a proper cuff pressure
(approximately 30-40 mmHg above the patient’s systolic pressure).

Manual level setting: Inflation level can be set manually between 100 and 280 mmHg. Set the
level to 30 to 40 mmHg higher than the expected systolic pressure.

• To set the P-SET to "AUTO," turn the P-SET Knob counterclockwise as far as it goes until you can hear a click.

• In the "AUTO" setting, inflation level may not be set automatically when the systolic blood pressure is more than
220 mmHg. Use the unit in the manual setting.

• If the cuff has not been inflated to the necessary level, it may be re-inflated automatically.

O

N/OFF

A

V

G

.

/

1

s

t

/

2

n

d

/

3

r

d

D

E

F

L

A

T

I

O

N

START

S

TOP

H

IDE

k

Pa

S

YS

P-SET

100

AUTO

140 180

220

260

280

MODE

AVG.

MANU.

CHECK

SINGLE

ON/OFF

A

V

G

.

/

1

s

t

/

2

n

d

/

3

r

d

D

E

F

L

A

T

I

O

N

START

STOP

HIDE

kPaSYS

P-SET

100

AUTO

140 180

220

260

280

MODE

AVG.

MANU.

CHECK

SINGLE

(2) Non-display function

Use to prohibit the display of measurement results. However,
the cuff pressure during measurement is displayed.
This function can be used in the SINGLE and AVG Modes.

By pushing the Button, display or non-display of status
is switched alternatingly.

H

IDE

(3) Manual deflation control

Accelerate deflation by pushing the DEFLATION (deflation
control) / Measurement Result Display Switch Button during
deflation in the measurement by the MANU Mode.

With each push of the Button, cuff is deflated rapidly
in increments of 5 to 10 mmHg.

BPM

mmHg

PULSE

SYS

mmHg

DIA

AC

AC

Display Non-display

P-SET

HIDE

HEM-907XL Rev B 3/2/07 1:41 AM Page 12

13

FEATURES AND FUNCTIONS

O

N/OFF

A

V

G

.

/

1

s

t

/

2

n

d

/

3

r

d

D

E

F

L

A

T

I

O

N

START

STOP

HIDE

AC

P-S

ET

100

AUTO

140 180

220

260

2

80

M

ODE

AVG.

M

ANU.

C

HECK

SINGLE

XL

®

ON/OFF

A

V

G

.

/

1

s

t

/

2

n

d

/

3

r

d

D

E

F

L

A

T

I

O

N

START

STOP

HIDE

A

C

P-S

ET

100

AUTO

140 180

220

260

2

80

M

ODE

AVG.

M

ANU.

C

HECK

SINGLE

X

L

®

ON/OFF

A

V

G

.

/

1

s

t

/

2

n

d

/

3

r

d

D

E

F

L

A

T

I

O

N

START

STOP

HIDE

AC

P-SET

100

AUTO

140 180

220

260

280

MODE

AVG.

MANU.

CHECK

SINGLE

XL

®

List of Functions for each Mode

I

nflation level set-

ting

Non-display func-

tion

M

anual deflation

c

ontrol

Single (SINGLE)

Mode

Average

(AVG) Mode

Auscultation

(MANU) Mode

Check

(CHECK) Mode

Function

Measurement

Mode

(4) AVG Function setting

You can set the number of measurements, the waiting time until the 1st measurement, and the
measurement interval for the AVG Mode.

Items to set Set value

F1 Number of measurements 2 times or 3 times
F2

Waiting time until the start of 1st measurement

0 sec, 3 min, 5 min, or 10 min.

F3 Measurement interval 5 sec, 30 sec, 1 min, or 2 min.

Note: The bold letters represent the factory-set values.

Procedure to change the set values

1) When the power is OFF, push the ON/OFF (power) Button
for more than three seconds while holding the START Button;
F1 is displayed.

2) Push the START Button and select the function to set from
F1 to F3. Each time you push the START Button, the func­tions change in the order of .

3) Push the DEFLATION (deflation control)/Measurement
Result Display Switch Button and change the set values.

4) When the setting is finished, push the ON/OFF (power)
Button to turn off the power. The setting is changed.

min
sec

Function #

HEM-907XL Rev B 3/2/07 1:41 AM Page 13

14

HOW TO APPLY THE CUFF

General advice

• Do not inflate the cuff without being wrapped over
the arm.

• Do not use a damaged cuff.

1. Select the cuff according to the arm size

Arm circumference Name of the cuff

(7

" - 9") 17-22 cm HEM-907-CS19 (Small)

(9" - 13") 22-32 cm HEM-907-CR19 (Medium)
(13" - 17") 32-42 cm HEM-907-CL19 (Large)
(17" - 20") 42-50 cm HEM-907-CX19 (Extra Large)

• Check the following before applying the cuff:

1) The bladder is correctly installed in the cuff.

2) The bladder is not twisted inside the cuff.

3) The bladder tube is protruding from the cuff as shown in
the Figure on the right.

2. Connect the air tube securely.

• Connect the air tube to the main unit by securing
the air plug to the base of the air connector

.

• Securely connect the air tube and the cuff/bladder
set by rotating the luer connection as shown in
the Figure on the right.

Do not wrap the cuff over an arm to which
intravenous injection or transfusion is being
conducted, or when otherwise contraindicated.

Do not connect the air tube or the cuff to other
equipment which is connected to intracorporeal
organ. Air embolisms may result.

The cuff of OMRON IntelliSense®Blood Pressure Monitor HEM-907XL plays an important role of
collecting the information on blood vessels. Please wrap the cuff according to the procedure, below.

Cuff

Air tube

Air connector

Air plug

Cuf

f side

Air tube side

Extract the air tube from .

Enlarged figure of

the circled part

The extra-large cuf

f comes with an air tube with
an integrated air plug. Connect the air plug of the
cuff to the air connector securely when
connecting to the main unit.

To use the cuff in extra-large size only

To use the cuff in small, medium or large size

HEM-907XL Rev B 3/2/07 1:41 AM Page 14

15

HOW TO APPLY THE CUFF

4. Align the Artery Position Mark
with the brachial artery.

5. Wrap the cuff snugly using both hands
and securely fasten it with the Velcro™
tape. At this time, the lower edge of
the cuff must be placed 1/2" to 1"
above the inner side of elbow joint.

• If the INDEX is positioned outside the RANGE, select the cuff suitable for the
patient's arm circumference and wrap it again.

• Wrap the cuff so that you can insert only one finger between the cuff and arm.

6. Keep the level of the cuff at the
same level as the heart during the
measurement.

3. Place the right or left hand of the patient
with the palm of hand facing upward.

1/2"-1"

HEM-907XL Rev B 3/2/07 1:41 AM Page 15

16

HOW TO USE THE POWER SOU RC E

General advice

• Read the instruction manual of the other devices
to be used at the same time with this unit to
understand and be aware of the interaction
between the devices.

D

o not use this unit in the presence of
flammable gas, or anesthetics, or in a high
pressure oxygen room or oxygen tent.

Do not touch the AC adapter with wet hands.

Be sure to use the AC adapter from the
power supply of 110 VAC.

Do not install or store this unit where it may
come in contact with water or liquid medication.

This is a Class II device with double isolation.
Earth pin is not for protective purposes.

®

[1]

[2]

How to use the AC adapter

Connect the AC adapter to the DC jack of the main unit [1] and the electric outlet [2].

NOTE: When the AC adapter is connected and the unit is turned off, the AC adapter

charges the installed rechargeable battery.

HEM-907XL Rev B 3/2/07 1:41 AM Page 16

17

HOW TO USE THE POWER SOU RC E

1. Remove both screws on the upper portion of
the battery cover of this unit, and remove
the cover.

2. Disconnect the old battery pack from the
connector and replace with a new one.

3. Install the battery cover and fasten it with both
screws. Be careful not to pinch the lead wire.

4. Connect the main unit to the AC adapter to
charge the new battery. The battery is not
charged when you purchase the monitor. When you use the battery for the first
time, charge it for more than twelve hours before use.

If battery fluid gets into your eye or comes in
contact with skin, wash the affected area with
water repeatedly. Immediately consult a doctor
for treatment.

Do not use the battery pack for devices other
than for this unit.

Do not disassemble the battery pack.

Installation and Replacement of Battery Pack

HEM-907XL Rev B 3/2/07 1:41 AM Page 17

18

HOW TO USE THE POWER SOURCE

Battery life

• You can use the unit for approximately three hundred measurements with one charge.

• Approximate life of battery is two years. However the battery life from each charging may be
shortened depending on the state of using. If the interval between charging becomes short and
the icon appears frequently, replace it.

Charging time

• At approximately five seconds after connecting the AC adapter, the unit will start battery charging
automatically.

• While the battery is being charged, the icon turns on.

• The battery can be completely charged in approximately twelve hours.

Battery low

• When the icon starts to blink, twenty to thirty measurements remain on the battery.

However if the Battery Low Mark starts to blink, charge it soon.

• If the icon is displayed, the battery is low and the unit cannot operate. Please charge
the battery.

Automatic Power Off

• When using the unit with the battery, the unit will turn off automatically after five minutes

of inactivity.

• While the AC adapter is connected, the Auto Power Off function does not work.

HEM-907XL Rev B 3/2/07 1:41 AM Page 18

19

HOW TO MEASURE BLOOD PRESSURE

General advice

• Patients should not touch the unit.

If cuff inflation does not stop, remove the cuff
or pull out the air tube from the main unit.

List of Measurement Modes

To measure

only once

SINGLE Mode

Refer to Page

20.

To measure two

times (or three times)

automatically and

consecutively

AVG Mode

Refer to Page

22.

To measure by

using a stetho-

scope

MANU Mode

Refer to Page

24.

Confirm readings with the stethoscope when
an irregular pulse wave is displayed or when
the measured value is questionable or erratic.

Do not use a cellular phone near this unit.
Do not use this unit in a vehicle.

HEM-907XL Rev B 3/2/07 1:41 AM Page 19

20

1. Push the ON/OFF (power) Button to
turn on the power.

2. Set the MODE Selector to "SINGLE".

3. Set the P-SET (inflation level) Knob
to "AUTO" or to the target pressure
value.

4. Measure the patient’s arm size, and
wrap appropriate cuff over the
patient's arm. (Refer to Pages 14
and 15.)

HOW TO MEASURE

BLOOD PRESSURE (IN SINGLE MODE)

HEM-907XL Rev B 3/2/07 1:41 AM Page 20

21

5. Push the START Button to start the
measurement.

• Do not push the
START Button without
wrapping the cuff.

• If you want to stop
measurement, push
the STOP Button. The
cuff will rapidly
deflate.

6. The measurement results are
displayed.

• While the battery pack is in use, the
monitor will turn off automatically after
five minutes of inactivity and the display
(measurement results) will disappear.
(Automatic Power Off)

7. Push the ON/OFF (power) Button to
turn off the power.

If the monitor determines that the pressure value is not correct,
an error display appears (Er1 to 9). In this case, refer to Page
28 and start the measurement again.

HOW TO MEASURE

BLOOD PRESSURE (IN SINGLE MODE)

HEM-907XL Rev B 3/2/07 1:41 AM Page 21

22

1. Push the ON/OFF (power) Button to
turn on the power.

2. Set the MODE Selector to "AVG".

The factory-set values are set as follows:

• Number of measurements: 2

• Waiting time until the 1st measurement: 0 sec.

• Interval: 1 min.

To change these factory-set values, refer to
Page 13.

3. Set the P-SET (inflation level setting)
Knob to "AUTO" or the target
pressure value.

4. Measure the patient’s arm size and
wrap appropriate cuff over the
patient's arm. (Refer to Pages 14
and 15.)

HOW TO MEASURE

BLOOD PRESSURE (IN AVERAGE MODE)

HEM-907XL Rev B 3/2/07 1:41 AM Page 22

23

5. Push the START Button to start the
measurement.

After the pre-select waiting time, the unit
takes the 1st measurement.

After displaying the results of 1st
measurement, subsequent measures occur
automatically at the specified intervals.

6. The measurement results are displayed.

After all the measurements are finished,
average values will be displayed.

Each time the DEFLATION (deflation control)
/ Measurement Result Display Switch Button
is pushed, the measurement results for each
reading and the average value will be displayed.

7. Push the ON/OFF (power) Button to
turn off the power.

If the monitor determines that the pressure
value is not correct, an error display appears
(Er1 to 9). In this case, refer to Page 28 and
start the measurement again.

• For setting the number of measurements,
the waiting time until the 1st measurement,
and the interval, refer to Page 13.

• If you want to stop measurement, push the
STOP Button. The unit will rapidly deflate.

• If an error occurs during measurement, the
monitor will automatically start measurement
again. If a second error occurs, measurement
will automatically stop.

• Do not push the START Button without

wrapping the cuff.

• While the battery is in use, the monitor will
turn off after five minutes of inactivity and
the display (measurement results) will
disappear. (Automatic Power Off)

HOW TO MEASURE

BLOOD PRESSURE (IN AVERAGE MODE)

HEM-907XL Rev B 3/2/07 1:41 AM Page 23

24

1. Push the ON/OFF (power) Button to
turn on the power.

3. Set the P-SET (inflation level setting)
Knob to "AUTO" or the target
pressure value.

4. Measure the patient’s arm size and
wrap appropriate cuff over the
patient's arm. (Refer to pages 14
and 15.)

2. Set the MODE Selector to "MANU".

HOW TO MEASURE

BLOOD PRESSURE (IN MANUAL MODE)

HEM-907XL Rev B 3/2/07 1:41 AM Page 24

25

5. Place the stethoscope on the
patient's arm.

6. Push the START Button to start the
measurement.

• Do not push the START Button without
wrapping the cuff.

• Do not squeeze or press the cuff during
the measurement.

• If you want to inflate again after the start

of deflation, push the START Button.

• If you want to accelerate deflation after the

start of deflation, push the DEFLATION
(deflation control) / Measurement Results
Display Switch Button. Each time the
Button is pushed, cuff is deflated rapidly in
increments of 5 to 10 mmHg.

9. Push the ON/OFF (power) Button to
turn off the power.

7. Take the readings.

8. Push the STOP Button to remove air
inside the cuff.

• The unit does not automatically deflate in
the MANU Mode.

If the monitor determines that the pressure
value is not correct, an error display appears
(Er1 to 9). In this case, refer to Page 28 and
start the measurement again.

HOW TO MEASURE

BLOOD PRESSURE (IN MANUAL MODE)

HEM-907XL Rev B 3/2/07 1:41 AM Page 25

26

Accuracy of pressure display can be checked in the CHECK Mode.

What you need to prepare

(1) Calibrated mercury manometer (including inflation bulb), (2) T-tube, (3) two air tubes, and (4)
a sturdy cylindrical shaped object on which the cuff is wrapped.

Check result

Accuracy of the monitor is validated to be ±3 mmHg or 2% of standard manometer reading. If your
result shows a difference exceeding the tolerance, contact Omron Healthcare’s Cusomer Service
at 1-877-216-1336.

How to check

1. Connect the manometer,
inflation bulb, cuff, and the
monitor with the T-tube as
shown in the figure on
the right.

2. Tightly wrap the cuff over a
sturdy cylinder.

3. Release the valve of inflation
bulb to remove the air inside
the cuff completely.

4. Push the ON/OFF (power) Button to turn on the monitor.

5. Set the MODE Selector to “CHECK”.

6. Close the valve of inflation bulb and inflate the cuff to the
pressure to be checked, based on the manometer read.

7. Compare the pressure values displayed on the monitor to
the one on the manometer.

®

HOW TO CHECK

PRESSURE ACCURACY (IN CHECK MODE)

HEM-907XL Rev B 3/2/07 1:41 AM Page 26

27

HOW TO CLEAN THE UNIT AFTER USE

XL

1. Wipe the monitor with a soft, damp cloth diluted with disinfectant alcohol, or
diluted detergent.

2. Complete cleaning by wiping the monitor with a soft, dry cloth.

General advice

• Do not clean this unit with gasoline, paint thinner, or
h

igh concentration alcohol.

• Do not disinfect this unit by autoclave or gas steril­ization (EtO, gluteraldehyde, or high concentration
ozone.)

When cleaning this unit, unplug the AC
a

dapter from the electric outlet.

After cleaning this unit, dry it well, before
plugging the AC adapter in the electric outlet.

HOW TO CLEAN THE UNIT AFTER USE

HEM-907XL Rev B 3/2/07 1:41 AM Page 27

28

LIST OF ERROR CODES

Error code Explanation

Inflation error

• When the pressure does not exceed 12
mmHg within the set time after the start of
inflation

•

When the inflation does not reach the set

c

uff pressure within the specified time

after the start of inflation

Deflation error

• When the deflation speed is too fast during
the measurement

• When the deflation speed is too slow
during the measurement

• When the measurement does not finish
within the specified time after starting the
measurement

Overpressure error

• The cuff pressure exceeded 299 mmHg.

Insufficient inflation error

• Blood pressure could not be measured
due to insufficient inflation level.

Indeterminable blood pressure error

•

Blood pressure could not be measured
even when the cuff pressure reached the
specified pressure.

Low pulse level error

• Pulse wave was too small.

Blood pressure error

•

Relationship between systolic and dias­tolic pressures was abnormal.

Pulse rate error

•

Pulse rate did not stay within the range of
30 to 199 beats/min.

Device error

• Main unit malfunction.

How to correct

• Confirm that the air tube connecting the cuff and
the main unit is connected securely.

• Confirm that the air flow in the air tube
c

onnecting the cuff and the main unit isn’t

b

eing restricted.

• Confirm that the cuff is wrapped correctly (refer
to pages 14 and 15).

• Check bladder for leaks and, if necessary,
replace the bladder with new one (option).

•

Confirm that air flow in the air tube connecting
the cuff and the main unit isn’t being restricted.

• If the measurement is made by setting the P-SET
to "AUTO", ask the patient not to move during
the inflation.

• Confirm that the P-SET is securely set to
"AUTO". Turn the Knob counterclockwise as far
as it goes until you can hear a click sound.

• If the measurement is made by manual inflation
level setting, set the value to 30 to 40 mmHg
higher.

• Confirm that the cuf

f is wrapped correctly (refer

to pages 14 and 15).

• Confirm that the cuff is wrapped correctly (refer

to pages 14 and 15).

•

Ask the patient not to move during the measure­ment.

• Check the patient for arrhythmia.

• Contact Omron Healthcare’s Cusomer Service
toll-free at 1-877-216-1336.

HEM-907XL Rev B 3/2/07 1:41 AM Page 28

29

TROUBLESHOOTING

Trouble

The unit inflates to
abnormally high (low)
pressure.

The monitor cannot
measure blood
pressure.

Measured values are
abnormally high (low).

What to inspect

Is the cuff wrapped correctly?

Is the patient moving during
inflation?

Does this patient have arrhythmia?

Check the patient's condition.

Is the patient moving during the
measurement?

Does the patient have an
arrhythmia?

Is the size of the cuff correct and
is it wrapped correctly?

Is the level of the brachium to
which the cuff is wrapped at the
same level as the heart?

How to correct

Wrap the cuff correctly, and
measure again.

(Refer to Page 14 and 15.)

Ask the patient not to move
during measurement, and
measure again.

Set the P-SET to 30 to 40 mmHg
higher than estimated systolic
pressure of the patient, then
measure.

After checking the patient with
the stethoscope refer to the "list
of error codes".

(Refer to Page 28.)

Ask the patient not to move
during measurement, and
measure again.

Set the P-SET to 30 to 40 mmHg
higher than estimated systolic
pressure of the patient, then
measure.

Select the cuff according to the
patient's arm circumference, wrap
it correctly, then measure again.

(Refer to Pages 14 and 15.)

Keep the level of the brachium to
which the cuff is wrapped at the
same level as the heart, then
measure again.

If the unit malfunctions during use, please check the following:

Are the patient’s clothes restricting
normal blood flow to the arm?

Remove the clothing and
measure again.

HEM-907XL Rev B 3/2/07 1:41 AM Page 29

30

FIVE YEAR LIMITED WARRANTY

CAUTION

Your HEM-907XL IntelliSense®Automatic Blood Pressure Monitor is warranted to be free from manufacturing defects for a period
of five years under normal use.

The five year warranty excludes the monitor cuf

f. The cuf

f is warranted for a one year period.
This warranty extends only to the original retail purchaser.
To obtain warranty service contact Omron Healthcare’s Customer Service by calling 1-877-216-1336 for the address of the
repair location and the return shipping and handling fee. Information for warranty service is avalable on our website
at www.omronhealthcare.com
We will either repair or replace (at our option) free of charge any parts necessary to correct defects in the materials or workmanship.
The above warranty is complete and exclusive. The warrantor expressly disclaims liability for incidental, special, or consequential
damages of any nature. (Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
warranty may not apply to you.)
Any implied warranties arising by the operation of law shall be limited in duration to the term of this warranty. (Some states do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. As a condition to operation
of your warranty, the enclosed registration card must be completed and sent to us within 10 days from the date of purchase.

FOR CUST

OMER SER

VICE CALL

T

OLL

FREE:

1-877-216-1336

CAUTION:

Changes or modifications not expressly approved by Omron Healthcare, Inc. could void the user’s authority to
operate this product.

NOTE:

POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only)
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If the product does cause harmful interference to radio or television reception,
which can be determined by turning the product on and off, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the product and receiver.

• Connect the product into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for Canada only)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in
the interference-causing equipment standard entitled "Digital Apparatus", ICES-003 of the Canadian Department of
Communications.

Cet appareil numérique respecte les limites de bruits radioeléctriques applicables aux appareils numériques de Classe
B prescrites dans la norme sur le matériel brouilleur: "Appareils Numériques", NMB-003 èdictée par le ministre des
communications.

HEM-907XL Rev B 3/2/07 1:41 AM Page 30

31

N

ame: OMRON Digital Automatic Blood Pressure Monitor

Model:

HEM-907XL

D

isplay: Digital display
Measurement: Oscillometric method
M

easurement Range: Pressure; 0 to 299 mmHg

Pulse rate; 30 to 199 beats/min

Accuracy: Pressure; Within ±3 mmHg or 2%

Pulse rate; Within ±5% of reading
Inflation: Automatic inflation with pumping
Deflation: Automatic deflation by electromagnetic control valve
Air Release: Automatic rapid air release by electromagnetic control valve
Pressure Detection: Electrostatic capacity semi-conductor pressure sensor
Power supply: AC adapter (120 VAC, 60 Hz, 20 VA) or

Battery pack (4.8 VDC, 6W)
Electic Shock Protection Method: Class II B type
Operating Tenmperature and Humidity: 50°F to 104°F (10 to 40°C), 30 to 85% RH, IPX 0 Rating
Weight of Main Unit: Approx. 32 oz (910 g)
External Dimensions: Approx.5 1/2" (W) x 8"(H) x 5 1/6"(D)

139 (W) x 203 (H) x 131 (D) mm
Accessories: Cuff / bladder set Extra Large, Cuff / bladder set Large, Cuff / bladder set

Medium, Cuff / bladder set Small,

AC adapter, Battery pack, air tube (1.0 m), Instruction Manual

(with guarantee card)
Options: Cuff Extra Large (without bladder), cuff Large (without bladder), cuff Medium

(without bladder), cuff Small (without bladder), Bladder Extra Large, bladder

Large, bladder Medium, bladder Small, air tube 1.3 m (51 1/6"),

Stand exclusive for this unit, wall-hanging kit, pole-mounting kit

Complies with: IEC 60601-1:1998+A1:1991+A2:1995 General requirements for safety

IEC 60601-1-2:1993

Electromagnetic compatibility ­Requirements and tests

AAMI SP10:1992 Manual, Electronic or Automated

Sphygmomanometers

Please note that specifications may be changed without prior notice.

Medical Equipment with respect to electric shock, fire and
mechanical hazards only in accordance with UL 2601-1 and
CAN/CSA C22.2 No. 601.1

SPECIFICATIONS

HEM-907XL Rev B 3/2/07 1:41 AM Page 31

For Customer Service

Call Toll Free

1-877-216-1336

Manufactured by OMRON HEALTHCARE
Distributed by:

OMRON HEALTHCARE, INC.

1200 Lakeside Drive
Bannockburn, Illinois 60015
www.omronhealthcare.com

Copyright © 2007 OMRON HEALTHCARE, INC.
HEM-907XLINST Rev B 1628519-0B

HEM-907XL Rev B 3/2/07 1:41 AM Page 32