Omega Products PX610-10KG V Installation Manual

PX610 Series

Subminiature Millivolt Output Type
Pressure Transducer

DESCRIPTION

The OMEGA®PX610 subminiature millivolt output type
pressure transducers are for accurate measurements in
restricted locations. These transducers are manufactured
with a unitized metal (stainless) diaphragm. The advantage
of this type of design is that a thin diaphragm and heavy
sidewalls are made from one piece of stainless steel. This
unitized diaphragm is rugged, but at the same time is
capable of being made thin enough to measure pressures of
only a few inches of water.

The diaphragm is welded to the transducer body to provide
a hermetic seal for water applications. The transducers use
epoxy to seal around the base of the diaphragm and to seal
around the electrical leadwire exit at the rear of the body. For
air and nonconductor fluid applications, the epoxy seals will
not impair performance, however, if the transducers are to be
used in water, high moisture areas, or corrosive fluids, the
diaphragm should be welded to prevent moisture from
penetrating inside the transducer and causing the strain gage
to short to the metal case.

AVAILABLE MODELS

The following models are available from OMEGA
Engineering, Inc.

UNPACKING

Remove the Packing List and verify that all equipment has
been received. If there are any questions about the shipment,
please call the OMEGA Customer Service Department at

1-800-622-2378 or 203-359-1660. We can also be reached on
the Internet at

omega.com
e-mail: [e-mail]

Upon receipt of shipment, inspect the container and
equipment for any signs of damage. Take particular note of
any evidence of rough handling in transit. Immediately
report any damage to the shipping agent.

The carrier will not honor any claims unless all shipping material
is saved for their examination. After examining and removing
contents, save packing material and carton in the event
reshipment is necessary.

MOUNTING

These transducers all use an O-ring for pressure sealing. to
get the best seal with the O-ring on the transducer, the
tapped hole should have the dimensions as shown below. For
normal operating temperatures (-53.8° to 12.1°C [-65° to
250°F]) use BUNA-N (black) O-rings. Maximum installation
torque is 500 in-lbs.

NOTE

RANGE MODEL RANGE MODEL

0-200 PSIG PX610-200G V 0-3000 PSIG PX610-3KG V

0-500 PSIG PX610-500G V 0-5000 PSIG PX610-5KG V

0-1000 PSIG PX610-1KG V 0-10000 PSIG PX610-10KG V

0-2000 PSIG PX610-2KG V

INSTRUCTION

SHEET

Shop online at: omega.com e-mail: [e-mail]
For latest product manuals: omegamanual.info

M0309/0505

Servicing North America:

U.S.A.: One Omega Drive, Box 4047

ISO 9001 Certified Stamford, CT 06907-0047

Tel: [phone] FAX: [phone]
e-mail: [e-mail]

Canada: 976 Bergar

Laval (Quebec) H7L 5A1, Canada
Tel: [phone] FAX: [phone]
e-mail: [e-mail]

For immediate technical or application assistance:

U.S.A. and Canada:

Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA

®

Customer Service: 1-800-622-2378 / 1-800-622-BEST

®

Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN

®

Mexico: En Espan˜ol: [phone]-7803 e-mail: [e-mail]

FAX: [phone] [e-mail]

Servicing Europe:

Benelux:

Postbus 8034, 1180 LAAmstelveen, The Netherlands
Tel: [phone] FAX: [phone]
Toll Free in Benelux: 0800 0993344
e-mail: [e-mail]

Czech Republic: Frystatska 184, 733 01 Karvina´, Czech Republic

Tel: [phone] FAX: [phone]
Toll Free: 0800-1-66342 e-mail: [e-mail]

France: 11, rue Jacques Cartier, 78280 Guyancourt, France

Tel: [phone] FAX: [phone]
Toll Free in France: 0800 466 342
e-mail: [e-mail]

Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

Tel: [phone] FAX: [phone]
Toll Free in Germany: 0800 639 7678
e-mail: [e-mail]

United Kingdom: One Omega Drive, River Bend Technology Centre

ISO 9002 Certified Northbank, Irlam, Manchester

M44 5BD United Kingdom
Tel: [phone] FAX: [phone]
Toll Free in United Kingdom: 0800-488-488
e-mail: [e-mail]

OMEGAnet®On-Line Service Internet e-mail

omega.com [e-mail]

FOR WARRANTY RETURNS, please have the
following information available BEFORE contacting
OMEGA:

1. Purchase Order number under which the
product was PURCHASED,

2. Model and serial number of the product under
warranty, and

3. Repair instructions and/or specific problems
relative to the product.

FOR NON-W

ARRANTY

REPAIRS,

consult OMEGA
for current repair charges. Have the following
information available BEFORE contacting OMEGA:

1. Purchase O rder number to cover the COST

of the repair,

2. Model and serial number of the product, and

3. Repair instructions and/or specific problems

relative to the product.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the
latest in technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2005 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or

reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.

WARRANTY/ DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period
of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to
the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA’s
customers receive maximum coverage on each product.

If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue
an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is
found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting
from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design
limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been
tampered with or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture
or vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA’s control.
Components in which wear is not warranted, include but are not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither
assumes responsibility for any omissions or errors nor assumes liability for any damages that result
from the use of its products in accordance with information provided by OMEGA, either verbal or
written. OMEGA warrants only that the parts manufactured by the company will be as specified and
free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND
WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES
INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are
exclusive, and the total liability of OMEGA with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the purchase
price of the component upon which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical
applications or used on humans. Should any Product(s) be used in or with any nuclear installation or activity,
medical application, used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our
basic WARRANTY/ DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA
harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.

RETURN REQUESTS / INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING
ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM
OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR
number should then be marked on the outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.

It is the policy of OMEGA Engineering, Inc. to comply with all worldwide safety and EMC/EMI regulations
that apply. OMEGA is constantly pursuing certification of its products to the European New Approach
Directives. OMEGA will add the CE mark to every appropriate device upon certification.

The information contained in this document is believed to be correct, but OMEGA
Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to
alter specifications without notice. WARNING: These products are not designed for use in,
and should not be used for, human applications.

CONSTRUCTION

BODY MATERIAL: 17-4 PH Stainless Steel
DIAPHRAGM MATERIAL: 17-4 PH Stainless Steel
O-RING SIZE: 2-012
ELECTRICAL CONNECTION: PT06F-10-6S (not included)
WEIGHT: 42.5 g (1.5 oz)
DIMENSIONS: See below

WIRING

A+B +EXCIT
C + D -EXCIT
E -SIGNAL
F +SIGNAL

SPECIFICATIONS

EXCITATION: 5 Vdc @ 15mA
OUTPUT: 10 mv
SENSITIVITY: 2mV/V nominal
INPUT RESISTANCE: 350Ω
OUTPUT RESISTANCE: 350Ω
INSULATION RESISTANCE: >5MΩ @ 75 Vdc
PERFORMANCE

ACCURACY: ±1% full scale
LINEARITY & HYSTERESIS: ±1% full scale best fit straight line
REPEATABILITY: ±0.02 mV; ±0.1% full scale
ZERO BALANCE: ±3%
OPERABLE TEMP. RANGE: -53.9° to 148.9°C (-65° to 300°F )
COMPENSATED TEMP. RANGE: 15.5° to 71.1°C (60° to 160°F)
THERMAL ZERO EFFECT: +0.0015mV/°F; ±0.01% full scale/°F
THERMAL SENSITIVITY EFFECT: +0.002mV/°F; ±0.02% full scale/°F
PROOF PRESSURE: 1.5 x Range
BURST PRESSURE: 4 x Range; 20,000 maximum