Omega Products PX6000L0-015AI User Manual

DIFFUSED SEMICONDUCTOR

ELECTRICAL CONNECTION BENDIX PTIH-10-6P OR EQUIV. MATES WITH BENDIX PTS06A-10-6S OR EQUIV. (NOT SUPPLIED). ALS O AVA ILAB LE: 4-PIN SOLDER TERM. OR INTEGRAL 0.6 m (24") CABLE

PX6000

17.5 ±0.25

(0.688 ±0.010)

WRENCH

FLATS

PXM6000

G1/4

(0.71)

HEX

PX6000: PRESSURE PORT PER MS3656-4* ALSO AVAILABLE: MS33649-4 (FEMALE) 1/4-18 NPT (MALE OR FEMALE) 1/8-27 NPT (MALE OR FEMALE PXM6000: G1/8 OR G1/8 (MALE OR FEMALE)

38 DIA.

(1.51) MAX.

76 MAX.

(3.00)

6.4 ±0.25

(0.25 ±0.01)

FLATS

PRESSURE TRANSMITTER

STANDARD AND METRIC MODELS

PX6000/PXM6000 Series

4 to 20 mA Output 0-15 to 0-300 psi-Standard Models 0-1 to 0-25 bar-Metric Models

Starts at

550

inert materials are deposited or grown on the chip surface to provide electrical isolation between the sensor and pressure medium.

⻬ High Reliability ⻬ Long-Term Stability ⻬ All Stainless Steel Case ⻬ Vacuum Range Available ⻬ Built-In Temperature

Sensor

Applications

⻬ Automotive Testing ⻬ Research and

Development

⻬ Engineering Testing

and Evaluation

⻬ Production Testing ⻬ Flight Recorders ⻬ Engine Monitoring ⻬ Ground Support

Equipment

OMEGA’s PX6000/PXM6000 Series pressure transducers fit easily into many applications. These low-cost transducers are small and light, and mounting requires no bulky structures. Users can select from 3 electrical terminations and 6 pressure fittings. The sensor is a small [about 2.54 mm (0.1") square] silicon chip, with 4 diffused strain gages mounted in the stainless steel case. Laser-trimmed resistors provide temperature compensation and adjust zero balance and span. The 4 to 20 mA output easily interfaces with most control and data acquisition systems. The PX6000/PXM6000 uses solid state media isolation for improved reliability. Thin films of chemically

These sensors are less sensitive to vibration and more dependable in high-shock environments because the films add no significant mass. Corrosion resistance is outstanding, and the isolation will remain effective because there are no gel or oil columns to deteriorate.

SPECIFICATIONS

Excitation: 12 to 40 Vdc unregulated Output: Load Impedance (Max):

50 x (V - 10) Ω where V = supply voltage (40 Vdc max)

Zero Balance:

4 mA adjustable ±10% FS

Dielectric Isolation Resistance:

100 MΩ minimum at 45 Vdc applied between the case or a conductive medium and the bridge circuit

Sensing Element:

4-active-arm bridge using a micromachined diffused silicon diaphragm sensor, thin-film media and dielectric isolation barriers

Temperature Sensor: Output resistance @ 24°C (75°F) 900 to 1500

Temperature Coefficient:

8% min, 10% max per 55.5°C (100°F) Accuracy: Combined linearity,

hysteresis and repeatability ≤±0.25% FS for all ranges

Operating Temp Range:

-29 to 85°C (-20 to 185°F)

Compensated Temp Range:

-29 to 85°C (-20 to 185°F)

Thermal Effects:

Vibration Sensitivity: At 20 g peak

sinusoidal vibration from 10 to 2000 Hz

(

0.04% FS/g for 15 psi range to

0.005% FS/g for 100 psi and above

4 to 20 mA adjustable ±10% FS

Span: ≤±0.02% of FS/°F Zero: ≤±0.02% of FS/°F

⁄2" D.A.), the output shall not exceed

B-212

Twist-lock style.

STANDARD

PX6000L1-100GI, $550, shown actual size.

Natural Frequency: Greater than

35 kHz for 100 psi and above Shock: 100 g, 11 ms half sine wave

without damage Proof Pressure: 2 times rated pressure

will not cause changes in performance beyond the specified tolerances

Burst Pressure: 3 times rated pressure for pressure ranges below 200 psi, or 2.5 times rated pressure for pressure ranges above 200 psi, will not cause rupture of the pressure sensor

Wetted Parts: 316 stainless steel, silicon, Pyrex

Electrical Connection: PTIH-10-6P (standard), 0.6 m (2') cable or 4-pin solder terminal header (optional)

Pressure Port: See dimensional drawing below

Weight: 170 g (6 oz) typical Mating Connector: PTS06A-10-6S

(sold separately)

glass, epoxy, Kovar

Dimensions: mm (in)

DIN Pin Wire Code

A RED = + INPUT B YEL = N/C C WT = N/C D BL = - INPUT E ORG = Temp Sensor F BRN = Temp Sensor Shield = Case Ground

PRESSURE TRANSDUCERS

CURRENT OUTPUT

DIFFUSED SEMICONDUCTOR PRESSURE TRANSMITTER

STANDARD CUSTOM CONFIGURATIONS

PX6000 PRESSURE ELECTRICAL RANGE SERIES PORT CONNECTION (psi) UNITS OUTPUT OPTIONS

A = B = 1⁄8-27 NPT female C = 1⁄4-18 NPT male D = 1⁄4-18 NPT female L = MS33656-4 male M = MS33649-4 female

Ordering Examples: PX6000M1-100GI, 100 psi vented gage pressure transducer with MS33649-4, female pressure connection, PT1H-10-6P electrical connector, 4 to 20 mA output, $550. PTS06A-10-6S, mating connector (sold separately), $47.

PX6000L1-015AI, 15 psi absolute pressure transducer with MS33656-4, male pressure connection, PTIH-10-6P, electrical connector and 4 to 20 mA output, $560. PTS06A-10-6S, mating connector (sold separately), $47.

[ 1 ] [ 2 ] [ 3 ] [ 4 ] [ 5 ] [ 6 ]

⁄8-27 NPT male

0 = 0.6 m (2') PVC cable (std)

+$4.50/ft over 0.6 m (2')

1 = PTIH-10-6P connector

(or equal, no charge). Mating connector (sold separately), order

PT06A-10-6S(SR) $18.

3 = 4-pin eyelet header (no charge);

temp sensor not available on 4-pin connector

6 = mini DIN connector (no charge)

no temp sensor

30* 015 020 050 100 200 300

* Referenced to atmospheric pressure,

VAC A,G A,G A,G A,G A,G A,G

30 Vac range is 30 to 0 inHg vacuum, all other ranges are psi

Base Price PX6000

I = 4 to 20 mA output

$550 all ranges

To order a custom configuration:

1. Select a pressure port

2. Select electrical connection

3. Select a pressure range

4. Select pressure units

5. Select output

6. Select options and agency approvals

CAL11 = 11-point NIST

calibration +$150

( )ft = Optional cable

length in feet

METRIC CUSTOM CONFIGURATIONS

PXM6000 PRESSURE ELECTRICAL RANGE SERIES PORT CONNECTION (BAR) UNITS OUTPUT OPTIONS

MA = G MB = G1⁄8B Female no charge MC = G1⁄4B Male +$20 MD = G1⁄4B Female no charge

Ordering Examples: PXM6000MB0-010BARGI, 10 bar gage pressure transducer with G termination, $560.

PXM6000MD1-010BARAI, 10 bar absolute pressure transducer with G mating connector (sold separately), $26.50.

[ 1 ] [ 2 ] [ 3 ] [ 4 ] [ 5 ] [ 6 ]

⁄8B Male +$20

0 = 3 m (10') cable (std)

$15/m over 3 m (10')

1 = PTIH-10-6P connector

(or equal, no charge) Mating connector (sold separately), order

PT06A-10-6S(SR) $18.

3 = 4-pin eyelet (no charge)

no temp sensor

6 = mini DIN connector (no

charge) no temp sensor

-1

1.0

1.6

4.0

6.0 10 16 25

See page B-12 for additional options including extended compensated temperatures.

VAC A, G A, G A, G A, G A, G A, G A, G

⁄4B female connection and twist-lock connector, $560. PTS06A-10-6S,

Base price PXM6000 I= 4 to 20 mA $560 All Ranges

CAL11 = 11-point calibration

To order a custom configuration:

1. Select a pressure port

2. Select electrical connection

3. Select a pressure range

4. Select pressure units – absolute, gage

or sealed gage

5. Select output

6. Select options and agency approvals

⁄8B female connection and 3 m (10') cable

certificate +$150

( )m = Optional cable

length in meters

B-213

+ 2 hidden pages