Omega Products CNi8C23 User Manual

1
54.84
(2.159)
8 DIN Ultra Compact Case, Temperature,
Process and Strain PID Controllers
CNi8C Series
CNi8C33, shown smaller than actual size.
U Ultra Compact 1⁄8 DIN Controller U Built-In Excitation U NEMA 4 (IP65) Bezel U RS232, RS422/485 or MODBUS
Communication, Menu Selectable
The ultra-compact CNi8C and CNi8SC controllers are similar to the full size CNi8 in an ultra-compact enclosure. Only 51 mm (2") behind the panel.
Options Ordering Suffix Description
Limit alarm version
-AL
Simplified menu (on/off
-SM
Network Options
Isolated RS232 and RS485/422,
-C24
Power Supply
-DC 12 to 36 Vac/dc, 24 Vac Factory Setup
-FS Factory setup and configuration
Factory scaled for MIL-T-7990B
-FS(RTD-1N)
Factory scaled for MIL-T-7990B
-FS(RTD-2N)
Software (Requires Network Option)
OPC-SERVER OPC server/driver
LICENSE software license
1
*
-DC”, “-C24”, and “-C4EI” not available with excitation.
2
*
Analog output is not available with “-AL” units.
3
*
“-SM” option not avaialbe on CNiS strain models.
(simplified menu, alarms only, no PID control)
or alarms, no PID)
300 to 19.2 Kb
2
*
control
3
*
1
*
Standard power input: 90 to 240 Vac/dc, 50 to 400 Hz (no entry required)
1
*
nickel RTD input, 0 to 200°C (32 to 392°F)
nickel RTD input, -40 to 300°C (-40 to 572°F)
ULTRA
COMPACT
Dimensions: mm (inch)
To Order
Visit omega.com/cni_series for Pricing and Details
(2.159)
104.10 (4.100)
54.84
CNi8C
CNi8
Model No. Output 1 Output 2
1
8 DIN Compact Case with 2 Control Outputs
CNi8C33 Relay Relay CNi8C34 Relay DC pulse CNi8C44 DC pulse DC pulse CNi8C22 0.5 A SSR 0.5 A SSR CNi8C23 0.5 A SSR Relay CNi8C24 0.5 A SSR DC pulse CNi8C53 Analog Relay CNi8C54 Analog DC pulse CNi8C52 Analog 0.5 A SSR
1
8 DIN Compact Case Strain/Process
Input
with 2 Control Outputs CNiS8C33 Relay Relay CNiS8C44 DC pulse DC pulse CNiS8C43 DC pulse Relay CNiS8C42 DC pulse 0.5 A SSR CNiS8C22 0.5 A SSR 0.5 A SSR CNiS8C23 0.5 A SSR Relay CNiS8C24 0.5 A SSR DC pulse CNiS8C53 Analog Relay CNiS8C54 Analog DC pulse CNiS8C52 Analog 0.5 A SSR
Ordering Examples: CNi8C33,
process controller with 2 relay outputs.
1
DIN compact universal temperature
8
P-21P-21
Common Specifications
(All
i/8, i/16, i/32 DIN)
Universal Temperature and Process Input (DPi/CNi Models)
Accuracy: ±0.5°C temp; 0.03% rdg Resolution: 1°/0.1°; 10 µV process Temperature Stability: RTD: 0.04°C/°C TC @ 25°C (77°F): 0.05°C/°C Cold Junction Compensation Process: 50 ppm/°C NMRR: 60 dB CMRR: 120 dB A/D Conversion: Dual slope Reading Rate: 3 samples/s Digital Filter: Programmable Display: 4-digit 9-segment LED
10.2 mm (0.40"); i32, i16, i16D, i8DV 21 mm (0.83"); i8 10.2 mm (0.40") and 21 mm (0.83"); i8DH RED, GREEN, and AMBER programmable colors for process variable, setpoint and temperature units Input Types: Thermocouple, RTD, analog voltage, analog current Thermocouple Lead Resistance: 100 Ω max
Thermocouple Types (ITS 90):
J, K, T, E, R, S, B, C, N, L (J DIN) RTD Input (ITS 68): 100/500/1000 Ω Pt sensor, 2-, 3- or 4-wire; 0.00385 or
0.00392 curve Voltage Input: 0 to 100 mV, 0 to 1V, 0 to 10 Vdc Input Impedance: 10 MΩ for 100 mV 1 MΩ for 1 or 10 Vdc
Current Input: 0 to 20 mA (5 Ω load) Configuration: Single-ended Polarity: Unipolar Step Response: 0.7 sec for 99.9% Decimal Selection:
Temperature: None, 0.1 Process: None, 0.1, 0.01 or 0.001
Setpoint Adjustment:
-1999 to 9999 counts Span Adjustment:
0.001 to 9999 counts
Offset Adjustment: -1999 to 9999
Excitation (Not Included with Communication): 24 Vdc @ 25 mA
(not available for low-power option)
Universal Strain and Process Input (DPiS/CNiS Models)
Accuracy: 0.03% reading Resolution: 10/1µV Temperature Stability: 50 ppm/°C NMRR: 60 dB CMRR: 120 dB A/D Conversion: Dual slope Reading Rate: 3 samples/s Digital Filter: Programmable Input Types: Analog voltage and current Voltage Input: 0 to 100 mVdc,
-100 mVdc to 1 Vdc, 0 to 10 Vdc Input Impedance: 10 MΩ for 100 mV; 1 MΩ for 1V or 10 Vdc
Current Input: 0 to 20 mA (5 Ω load) Linearization Points: Up to 10 Configuration: Single-ended Polarity: Unipolar Step Response: 0.7 sec for 99.9%
Decimal Selection: None, 0.1, 0.01
or 0.001 Setpoint Adjustment:
-1999 to 9999 counts
Span Adjustment: 0.001 to 9999 counts Offset Adjustment: -1999 to 9999 Excitation (Optional In Place Of Communication): 5 Vdc @ 40 mA;
10 Vdc @ 60 mA
Control
Action: Reverse (heat) or direct (cool) Modes: Time and amplitude proportional
control; selectable manual or auto PID, proportional, proportional with integral, proportional with derivative and anti-reset Windup, and on/off
Rate: 0 to 399.9 s Reset: 0 to 3999 s Cycle Time: 1 to 199 s; set to 0 for on/off Gain: 0.5 to 100% of span; setpoints 1 or 2 Damping: 0000 to 0008 Soak: 00.00 to 99.59 (HH:MM), or OFF Ramp to Setpoint:
00.00 to 99.59 (HH:MM), or OFF Auto Tune: Operator initiated from front panel
Control Output 1 and 2
Relay: 250 Vac or 30 Vdc @ 3 A (resistive
load); configurable for on/off, PID and ramp and soak Output 1: SPDT, can be configured as alarm 1 output Output 2: SPDT, can be configured as alarm 2 output SSR: 20 to 265 Vac @ 0.05 to 0.5 A (resistive load); continuous
DC Pulse: Non-isolated; 10 Vdc @ 20 mA Analog Output (Output 1 Only):
Non-isolated, proportional 0 to 10 Vdc or 0 to 20 mA; 500 Ω max
Network and Communications
Ethernet: Standards compliance
IEEE 802.3 10 Base-T Supported Protocols: TCP/IP, ARP, HTTPGET RS232/RS422/RS485: Selectable from menu; both ASCII and MODBUS protocol selectable from menu; p 300 to 19.2 Kb; complete programmable setup capability; program to transmit current display, alarm status, min/max, actual measured input value and status
RS485: Addressable from 0 to 199 Connection: Screw terminals
rogrammable
Alarm 1 and 2 (Programmable)
Type: Same as output 1 and 2 Operation: High/low, above/below,
band, latch/unlatch, normally open/normally closed and process/deviation; front panel configurations
Analog Output (Programmable):
Non-isolated, retransmission 0 to 10 Vdc or 0 to 20 mA, 500 Ω max (output 1 only); accuracy is ± 1% of FS when following conditions are satisfied: input is not scaled below 1% of input FS, analog output is not scaled below 3% of output FS
General
Power: 90 to 240 Vac ±10%, 50 to 400 Hz*,
110 to 375 Vdc, equivalent voltage Low Voltage Power Option: 24 Vac
12 to 36 Vdc for i/8, i/16, 1/32; 20 to 36 Vdc for CNi8DH, CNi8DV, CNi16D from qualified safety approved source
**,
Isolation
Power to Input/Output: 2300 Vac
per 1 minute test For Low Voltage Power Option: 1500 Vac per 1 minute test Power to Relay/SSR Output: 2300 Vac per 1 minute test Relay/SSR to Relay/SSR Output: 2300 Vac per 1 minute test RS232/485 to Input/Output: 500 Vac per 1 minute test Environmental Conditions: All Models: 0 to 55°C (32 to 131°F) 90% RH non-condensing CNi8DV, CNi8DH, CNi16D: 0 to 50°C (32 to 122°F), 90% RH non-condensing (for UL only) Protection: CNi32, CNi16, CNi16D, CNi8C:
NEMA 4X/Type 4 (IP65) front bezel CNi8, CNi8DH, CNi8DV: NEMA 1/Type 1 front bezel Approvals: UL, C-UL, CE per EN61010- 1:2001
Dimensions i/8 Series: 48 H x 96 W x 127 mm D
(1.89 x 3.78 x 5") i/16 Series: 48 H x 48 W x 127 mm D (1.89 x 1.89 x 5") i/32 Series: 25.4 H x 48 W x 127 mm D (1.0 x 1.89 x 5")
Panel Cutout i/8 Series: 45 H x 92 mm W
(1.772 x 3.622"), i/16 Series: 45 mm (1.772") square,
1
DIN
16
i/32 Series: 22.5 H x 45 mm W (0.886 x 1.772"),
Weight i/8 Series: 295 g (0.65 lb) i/16 Series: 159 g (0.35 lb) i/32 Series: 127 g (0.28 lb)
No CE compliance above 60 Hz.
* ** Units can be powered safely with 24 Vac
power, but no certification for CE/UL are claimed.
1
8
1
32
DIN
DIN
at any
setpoint
Patented
Totally Programmable Color Displays
P
P
P-22
P-22
Loading...