Oki MFR-2200, MFR-1100 User Manual

1
Copyright © OK International, Inc.
7000-2570_1
MFR-1100 & MFR-2200 Series User Guide
MFR-1100 & MFR-2200 系列 用户指南
MFR-1100 & MFR-2200 系列 使用者指南
MFR-1100 & MFR-2200 シリーズ ユーザーガイド
MFR-1100 & MFR-2200 시리즈 사용설명서
2
With power applied, the tip temperature can be > 300°C. Failure to observe the following precautions may lead to injury to users or damage the equipment:
Do not touch any metallic parts of the hand-piece
Do not use near flammable items
Do not use unit for any function other than described in this manual
Use only genuine MFR replacement parts
Use in a well ventilated area
Do not use the equipment with wet hands
Connect only to properly grounded outlets to prevent risk of electric shock.
Always place hand-piece back into the work stand to prevent accidental burning of oneself or surrounding objects.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Although the systems offer superior EOS (Electrical Overstress) protection, periodic checks of the instrument cord should be incorporated into standard operator maintenance procedures.
Waste Electrical and Electronic Equipment Directive - WEEE (2002/96/EC).
When this product is no longer required, if it cannot be re-used, we ask our customers not to dispose of it as unsorted municipal waste but to appropriately recycle the product. In Europe, please contact your OK International distributor who can advise the recycling options available (www.okinternational.com).
WARNING
!
3
Initial Setup & Operation.
1. Connect hand-piece(s) to power unit output connector(s).
2. Insert your selected tip or cartridge into the hand-piece. Push the tip or cartridge all the way until it seats (See instructions supplied with each hand­piece).
3. Place hand-piece(s) into associated work stand(s).
4. Add distilled water to work stand sponge (sulfur free).
5. (MFR-2200) Select the desired channel using the selector switch. Either Left, Right or Both (Selector switch is in the center position to run both channels simultaneously)
6. Plug the power cord into a grounded wall socket of the rated input line voltage.
7. To turn the unit on, push the AC power switch. The AC power LED should light up in green.
8. Unit must be grounded, otherwise it will not work, and the AC power LED will light in red.
9. Unit will not work in electrical network where an isolation transformer has been used.
Always use tip removal pad for changing tips.
AC Power LED
AC Power
Switch
Output
Connector
Channel
Switch
Channel
LED
MFR-
WS1 for soldering handpieces
or
MFR-WSPT for tweezers handpiece
MFR-H2-
MFR-H1-
MFR-H4-
See inserts for relevant hand-piece operating instructions
Contents and Identification of Features
MFR-PS1100
4
Channel LED
Green --- On / Ready
Red ------ Open connection: tip,
connector
Off ------- Channel not selected or channel is in Auto Off (cycle the power switch to reset)
AC Power LED
Green --- Power On
Red ------ Ground Fault
Off ------- Power Off
Auto-Sleep and Auto Off Functions
To prolong tip life, MFR systems with a soldering hand-piece (MFR-H1-SC, MFR-H2-ST) include an “Auto-Sleep Workstand” (WS1). When the hand-piece is placed into the workstand, the “Auto-Sleep Workstand” immediately reduces power to the hand-piece. All MFR systems have an “Auto Off” Function. The “Auto Off” Function will be engaged when the hand-piece has been idle in the sleep stand for a period of two hours. The channel LED indicator light will go from green to off. The “Auto Off” Function can be reset by cycling the power switch.
LED Indications and Meaning
System Specifications
Ambient Operating Temperature 10- 40°C Maximum Enclosure Temperature 55°C Input Line Voltage 100- 240 VAC, grounded circuit Input Line Frequency 50/60 Hz Power Consumption MFR-1100 90 Watts max MFR-2200 170 Watts max.(with both channels on) Output Power Max. 60 Watts max. Per channel at 22°C ambient
temperature Output Frequency 450--480 KHz Power Cord 3-Wire 183cm (18/3) SJT Dimensions w x d x h
MFR-1100 90mm (3.5”), 297mm (8”), 142 mm (5.6)
MFR-2200 122mm (4.8”), 200mm (8”), 152.5mm (6”) Certification / Marking cTUVus, CE Tip-to-Ground Potential <2mV Tip-to-Ground Resistance <2 ohms Idle Temperature Stability ± 1.1°C in still air Hand-piece Cable Length L=122cm (48”), burn proof, ESD safe Hand-piece Connector 8-pin circular DIN Workstand Dimensions w x d x h 100 mm (4”) x 200 mm (8”) x 100 mm (4”) max
MFR-PS1100
MFR-PS2200
5
Accessories & Spares
The following upgrade kits provide extra hand-pieces with workstands as a set
AC-CP2 Soldering cartridge / tip removal pad MFR-CA2 Coil Assembly for MFR-H2-ST handpiece MFR-PM70 Power meter, MFR, 0-70W scale
Soldering and Rework Tips and Cartridges
OKi offers a comprehensive range of cartridges and tips for each of its hand-pieces. For an up to date listing of all options please visit our web site at www.okinternational.com
MFR-H2-ST Soldering cartridge hand-piece
SxV Series production soldering & touch-up soldering tips CxV “Clean-up” blade tips for BGA pad clean-up
MFR-H1-SC Soldering tip hand-piece
SxP Soldering cartridge tips RxP Rework cartridge tips
MFR-H4-TW Precision tweezers hand-piece
TxP Series cartridges for SMD rework
6
SmartHeat® & Calibration
Each cartridge or tip is equipped with a self-regulating heater which ‘senses’ its own temperature and tightly maintains its pre-set idle temperature for the life of the heater-tip; all controlled by OK International’s proprietary SmartHeat® Technology. The tip temperature is determined by the inherent metallurgical properties of the heater; no external adjustment or equipment is required. The power delivered to the tip automatically varies in direct response to the thermal load. This eliminates spikes and transients associated with electrically switched elements found in conventional soldering irons. Please feel free to contact your OK International representative with any questions.
Warranty
OK International warrants the MFR against any defects in materials or workmanship for one (1) year from the date of purchase by the original owner. This Warranty excludes normal maintenance and shall not apply to any opened, misused, abused, altered or damaged items. If the product should become defective within the warranty period, OK International will repair or replace it free of charge at its sole option. The repaired or replacement item will be shipped, freight prepaid, to the original purchaser. The warranty period will start from the date of purchase. If the date of purchase cannot be substantiated the date of manufacture will be used as the start of the warranty period.
The MFR-H2-ST handpiece uses a coil assembly (MFR-CA2) which is a replaceable item. OK International warrants the coil for 30-days regular use.
For contact details for Warranty and Support look for your local office details at:
www.okinternational.com
Please visit OK International’s web page (www.okinternational.com) where you will find available information on systems, accessories, technical notes, and more.
7
通电后,焊嘴温度可达到 300°C 以上。请牢记以下注意事项,以免灼伤或损坏设备:
切勿接触手柄的任何金属部分
切勿在易燃物附近使用
切勿将本设备用于本手册中没有介绍的任何功用
请仅使用原装的 MFR 更换件
在通风良好的区域中使用
切勿在手潮湿的情况下使用本设备
只能连接已良好接地的电源插座,以避免触电的危险。
始终将手柄放置入工作台中,以避免意外灼伤自己或烧毁周围物体。
身体不适、感知能力或神智欠佳、或缺乏经验和知识的人群(包括儿童)不宜
使用本设备。如果他们确要使用本设备,应由负责他们安全的人员对设备的使
用进行监督或指导。
应看管好儿童,以防止他们玩耍本设备。
尽管系统提供了出色的 EOS(电性过压)保护,仍应将设备电线的定期检查纳入标准的 操作员维护程序中。
废弃电子电器设备指令 - WEEE (2002/96/EC)
如果客户不再需要使用本产品,且该产品无法再次利用,我们将 要求客户不要将产品当作未分类的市政废弃物处理,而是应当将 产品适当地回收再利用。 在欧洲,请联系您的 OK International 经销商,以获取可用的回收选项建议 (www.okinternational.com)
警告
!
8
首次安装和操作。
1. 将手柄连接到电源设备输出接口。
2. 将选择的焊嘴插入到手柄中。 用力推动焊嘴到底,直到其就位为止(请参阅每 个手柄随附的使用说明)。
3. 将手柄放入相关工作台。
4. 向工作台海绵(不含硫)添加蒸馏水。
5. (MFR-2200) 使用选择开关选择所需的通道。 可选择左通道、右通道,或两者 (选择开关处于中心位置时可同时运行两个通道)
6. 将电源线插入具有额定输入线电压的接地壁装插座中。
7. 要开启设备,请按下交流电源开关。 交流电源 LED 指示灯应亮起绿色。
8. 设备必须接地,否则设备将停止工作,同时交流电源指示灯亮起红色。
9. 设备无法在已经使用隔离变压器的电网中工作。
始终使用焊嘴拆卸垫更换焊嘴。
交流电源 LED 指示灯
交流电源开关 输出接口
通道开关
通道 LED 指示灯
MFR-PS2200
用于焊接手柄的 WS1
用于镊型手柄的 MFR-WSPT
MFR-H2-ST
MFR-H1-SC
MFR-H4-TW
请参见插页获得相关得手柄操作说明 系统组成及功能识别
无硫海绵
氧化物拆卸垫
MFR-PS1100
Loading...
+ 18 hidden pages