How it Works
Oki
Loading...
LUCIDIOM EQ-9800
Installation Manual
12 pgs1.91 Mb0
Installation Manual
14 pgs2.05 Mb0

Oki LUCIDIOM EQ-9800 Installation Manual

Download
Page 1
LUCIDIOM
EQ-9800
Installation
Guide
Page 2
Preinstall Checklist.................................................................................2
To print a configuration page: .................................................................2
Disable Auto Tray Switch........................................................................4
Media Type Setting................................................................................4
Disable Media Check .............................................................................. 4
To Configure Options Automatically.......................................................... 5
Configuration Page ................................................................................ 9
Driver Setup....................................................................................... 10
Rev. 3.6
Page 3
1 BEFORE YOU GO ONSITE
PREINSTALL CHECKLIST
These instructions assume that certain requirements have been fulfilled prior to installation. It is recommended that you call the customer and confirm that the following are in place before arriving onsite:
□ Network connection and cable are
available/tested and ready for the installation to the printer
□ Assigned IP address or DHCP? □ Location for the printer has been
cleared and ready to receive printer
□ PC is available and setup to install
drivers and software. Order of preference:
• WinXP with Photo Finale Lab (PFLAB)
• WinXP with Print Station
• Any WinXP computer
*Only schedule setup, when customer has WinXP.
□ PC should be able to contact printer’s
IP address
□ Open ports between PC and printer
• SNMP (port 161)
• HTTP (port 80)
2 SETUP PRINTER
Setup the printer, install the media and calibrate the printer. When finished, print a configuration page to ensure that the printer is working.
Contents:
EQ-9800 Printer
2nd Paper Tray (optional)
High Capacit y F eed er
Not Shown: Sample Media Pack
Install the media in the following trays locations:
O PRINT A CONFIGURATION PAGE:
T
MPT = All other media
Tray 1 = 10” x 7” 80# cover Tray 2* = 8.5” x 11” 100# text Tray 3 = 8.5” x 11” 80# cover Tray 4 = 12” x 12” 100# text Tray 5 = 12” x 18” 80# cover
*Tray 2 is an optional paper tray
• LPR (port 515)
□ ES-1000 (Eye-One) Spectrometer to
calibrate printer
□ Equipment (EQ-9800, paper trays and
sample media)
1. Press ENTER to switch to the menu mode.
2. Use the T key to scroll down to Print Pages. Press ENTER.
3. Use the T key to scroll down to Configuration. Press ENTER.
4. Display will read [Printing Config]
2
Page 4
3 ASSIGN AN IP ADDRESS TO
THE
If you are not using DHCP, you need to obtain an IP Address from your network Administrator and enter it using the front panel:
1. Confirm that the printer displays [Ready to print].
2. Press T key until [Admin Setup] appears. Press ENTER.
3. Continue to Setup? displays. Press E printer goes offline and Running Setup displays. This will take about a minute.
4. The Setup Menu displays, press T to select [Network Setup]. Press ENTER.
5. Press T to select [Protocol Setup]. Press ENTER.
6. Press T to select [TCP/IP Setup]. Press ENTER.
7. Press T to select [Ethernet Setup]. Press ENTER.
PRINTER
NTER to select Yes. The
12. [Gateway Address] displays. Repeat instructions in step 9.
13. Press ENTER to exit TCP/IP Setup,
Protocol Setup, and Network Setup.
14. Select Yes and press ENTER to Save Changes. Press ENTER to Exit the Setup Menu.
15. Printer restarts the server and initializes. [Ready to Print] displays.
4 CONFIGURE PRINTER
Press ENTER to switch to the menu
ode.
m
1. Use the T key to scroll down to the function you wish to change.
2. Press ENTER.
8. [TCP/IP Ethernet] displays. Select Yes and press E Enable AutoIP Config? displays. Select No. Press ENTER.
9. The default IP Address displays. Use ▲/T to change each octet. Press ENTER to proceed to the next octet or to leave the octet unchanged.
10. [Subnet Mask] displays. Repeat instructions in step 9.
11. [TCP/IP bound to Ethernet] displays. Press E
NTER.
NTER.
3. Use the T/S and E
NTER keys to drill
down to the item you wish to change.
4. Use the S/T keys to move to the setting you wish to engage.
5. Press ENTER.
An asterisk appears next to the new setting.
3
Page 5
6. Press ON LINE to exit the Menu mode.
DISABLE AUTO TRAY SWITCH
MENUS → TRAY CONFIGURATION → TRAY SWITCH → OFF
AUTO
MEDIA TYPE SETTING
MENUS → RAY ONFIGU CONFIG → MEDIA TYPE →
Repeat, changing the tray selection until all trays have been set to
T C RATION → TRAY1
GLOSSY
Glossy.
DISABLE MEDIA CHECK
Press ENTER.
1. Use the T key to sc [Admin S
etup]. Press ENTER.
roll down to
5 ADD A PRINTER
1. Open Printers by clicking the Start button, clicking Control Panel, clicking Printers and Faxes.
2. Click Add a printer.
3. When the Welcome to the Add
Printer Wizard appears, click Next.
4. Select Local printer attached to this computer. Deselect Automatically detect and install my Plug and Play printer, then
click Next.
2. T/S keys → Yes. Press ENTER. Offline appears on the display.
3. Wait for setup to run. The Setup menu appears
4. T/S keys → [Printer Setup]. Press ENTER.
5. Continue to press ENTER until you come to [Med
6. T/S key → Off. Press E Continue to press Enter >
7. [Save Changes?] T/S → Yes. Pres E
NTER.
8.
T/S key → [Exit Setup]. Press ENTER.
Printer will come back to ON
ia Check].
NTER.
s
LINE.
Select Creat
5. e a new port and
choose Standard TCP/IP Port
from the drop down menu.
6. Add
When the Welcome to the
Standard TCP/IP Printer Port Wizard appears, click Next.
7. n the
Type the printer’s IP address i field labeled Printer Name or IP Address. Click Next.
4
Page 6
8. On the Additional Port Information Required menu, choose Custom, then click the Settings… button.
9. On the Port Settings page, change the Protocol to LPR. Enter Print as the Queue Name. Check SNMP Status Enable, then click Ok. Click Next, then Finish.
16. On the Printer Sharing page, choose Do not share this prin and click Next.
17.
Print a test page to confirm your installation. Clic Finish.
6 AY COMMUNICATION
TWO W
After you have completed the printer driver installation, you must configure the printer for the installed options. You can configure the options manually or, for TCP/IP network connections, you can use the Two-Way Communication feature to configure the options automatically.
k Next, then
ter
TO CONFIGURE OPTIONS AUTOMATICALLY
On the Install the printer driver
10. page, click Have disk…
11. ate to the
Click browse, then navig driver location on Drivers, Color and Network Utilities CD.
<cdrom>\drivers\win2k_xp\p
12. S
13. Choose Oki C9800, then Next.
14. Select Keep existing driver
15.
elect OP723PS.inf. Click Ok.
(recommended), then click Ne On the Name Your Printer page,
type EQ-9800 and click Next.
s
xt.
If you have a TCP/IP-ena you can automati printer driver to reflect the options currently installed on the printer.
1. Click START → SETTINGS → PRINTER
2. Right-click the EQ-9800 icon.
3. Click Properties.
4. Click the Installable Options
cally update your
bled network,
S.
tab.
5
Page 7
5. Select Two-Way Communications.
6. Type the Fiery IP a name.
ddress or DNS
1
0. Click on Image Quality, then choose Best. Close Image Quality.
1
1. Click on Finishing.
7. To display the printers current default s select Update Fiery Driver Wh Opened.
8.
Click Update. Click OK.
If date, check that the IP address is
this does not up correct. If correct, then the customer m port 161 with network security.
7
PRINTING PREFERENCES D
EFAULTS
Righ rinter, and select
t-click on the p
Printing Preferences.
1. On the Fiery tab, click on Paper Source. Change the to Glossy.
2.
Scroll down and change Auto Tray Switch to O
ettings when opened,
ay be blocking
Media Type
ff.
en
12. Click on the drop down box for Two-sided Printing and cha to Long E
13. Click on Apply at the Close.
8
INSTALL COMMAND
dge Binding.
bottom and
nge
WORKSTATION
Insert the Fiery Administrator (p/ 35020001) into your CD-
n ROM
drive
.
1. Select your language.
2. Click Next to accept the License Agreement.
3. Sele
4. Select Quick Install to install only
ct your printer model. Click
Next.
Command W
orkStation.
Utilities
3. Change Media Check to Off. Click on Paper Sourc close those items.
4. ert
Click on Colorwise. Select Exp
Color, then click Ex Settings… button.
5.
Click Update.
6. wn menu for
Click on the drop do
RGB Source P Vivid.
7.
Click on the drop down menu for
Render Photographic.
8.
Click on the drop down menu for
Output Profile a Photo_r2. Click Ok.
9. Click on Colorwise to close.
ing Style and change to
e at the top to
pert
rofile and change to
nd change to
9 COLOR SETUP
1. Click START → ALL PROGRAMS → FIERY → COMMAND WORKSTATION4
C from the
2. hoose Log in/Log out Server menu. CWS4 will start searching for Fiery servers. Choose the device that matches th IP Address.
6
e correct
Page 8
3.
Click the Login button next to the Fiery name to establish th connection.
4.
Select the Administrator option and the click Log In.
n
e
3. Select Install the software
automatically (Recommended),
then click, Next.
4. Click Finish, when Windows has completed installing the hardware.
11 CALIBRATE PRINTER
1. Click START → ALL PROGRAMS → FIERY → COMMAND WORKSTATION4
2. Choose Log in/Log out from the Server menu. CWS4 will start searching for Fiery servers. Choose the device that matches the correct IP Address.
5.
Choose Manage Color from the
6. Choose Color Setup.
7. Click on the drop down menu for
RGB Source Profile and change to Vivid.
8. Click on the drop down menu for
Rendering Style and change to Photographic.
9. Uncheck “Use Media Defined Profile”.
10. Click on the drop down menu for
Output Profile and change to Photo_r2. Click Apply, then Ok.
Server menu.
10 INSTALL EYE-ONE DEVICE
Plug the Eye-One (ES-1000) device into an available USB slot.
1. A found new hardware wizard will appear.
2. Select No, not this time when it asks you to connect to Windows Update, then click Next.
3. Click the Login button next to the Fiery name to establish the connection.
4. Select the Administrator option and then click Log In.
5. Choose Manage Color from the Server Menu.
6. Click on Calibrator.
7. For Select Method, choose ES- 1000 Spectrometer from the drop down menu.
8. For the Screen Setting, choose 12x6 Dot Screen from the drop down menu.
9. Click Print.
10. On the Print Options Menu, keep the defaults and click Print. A
7
Page 9
page with 21 swatches will print to the printer.
11. Place the printed page on a stack of 5 sheets of blank paper to prevent bleed through.
12. Align the plastic guide strip up so that the center passes through the first column of swatches (Cyan).
16. Measure the cyan swatches by starting the ES-1000 in the grey bracket atop the swatches.
17. Click the button on the device and wait for an audible beep. If you cannot hear the beep then wait 1-2 seconds, before dragging the device down the page.
18. While holding the button drag the device smoothly down the plastic guide until you have passed the last swatch, then release the button. To judge the correct speed, from start to finish, use a count of 4.
19. When the scan has been successful, a check will appear and the red cross will move to the next color.
20. When all four colors have been scanned, click the Accept button.
Click Measure.
13.
14. Confirm that you
are doing 21
patches and click Measure.
15.
A window opens that request
“Please place the ES-1000 in i calibration cradle and click Ok.”
Click Ok.
21. Click Ok.
22. Click Apply.
ts
8
Page 10
12 CHECKLIST
After completing all the installation steps, print a configuration page. Confirm that all the items have been completed on the checklist, then fax the checklist with the configuration page to: 856-222-5098.
Date: Company Name: Contact: Address: City, State, Zip: Printer Serial No:
CONFIGURATION PAGE
Update Information
□ Check for Photo_2.2
Network Setup
□ Check the IP address and record. (Step 3)
Printer Setup
□ Last Calibration should be today on 12x6 Dot Screen (Step 11) □ Check that Media Check: Disabled (Step 4)
Color Setup
□ RGB Source Profile: Vivid RGB (Step 9) □ Rendering Style: Photographic (Step 9) □ Output Profile: Photo_r2 (Step 9)
Tray Configuration
□ Auto Tray Switch: Off (Step 4) □ Media Type (Trays 1-4 & MP Tray): Glossy (Step 4)
9
Page 11
DRIVER SETUP
□ Printer Name is EQ-9800 (Step 5) □ Test page prints successfully (Step 5)
Ports Tab → Configure Port
□ Protocol: LPR (Step 5) □ LPR Settings – Queue Name: Print (Step 5) □ SNMP Status Enabled: Checked (Step 5)
General Tab → Print Preferences → Fiery Tab Paper Source
□ Media Type: Glossy (Step 7) □ Auto Tray Switch: Off (Step 7) □ Media Check: Off (Step 7)
Colorwise Expert Color is selected
□ RGB Source Profile: Vivid RGB (Step 7) □ Rendering Style: Photographic (Step 7) □ Output Profile: Photo_r2 (Step 7)
Image
Quality
□ Image Mode: Best (Step 7)
Finishing
□ 2-Sided Printing: Long Edge Binding (Step 7)
10
Page 12
Page 13
Page 14
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use