NuTone NS130WW, NS130BL, NS136BL, NS136WW, NS136SS User Manual

...

MODELS NS130BL • NS130SS • NS130WW

NS136BL • NS136SS • NS136WW

NS Series Range Hood

READ AND SAVE THESE INSTRUCTIONS

FOR DOMESTIC COOKING ONLY

Page 1

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel. Lock or tag service panel to prevent power from being switched on accidentally.

3. Installation work and electrical wiring (including switch loca-

tion) must be done by a qualied person(s) in accordance with all applicable codes and standards, including re-rated

construction.

4. Provide sufcient air for proper combustion and exhausting of gases through the ue (chimney) of fuel burning equip-

ment to prevent backdrafting. Follow the combustion equipment standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and local codes.

5. This product may have sharp edges. Be careful to avoid cuts and abrasions during installation and cleaning.

6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

7. Ducted fans must always be vented to the outdoors.

8. Use only metal ductwork.

9. Do not use this fan with any solid-state speed control device.

10. As an alternative, this product may be installed with the ULapproved cord kit designated for the product, following instructions packed with the cord kit.

11. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave greasy cooking unattended. Oil, butter, lard, etc. can ignite in a few minutes.

2. Always turn hood ON when cooking at high heat or when

cooking aming foods.

3. Always use cookware appropriate for the size of the surface element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-tting lid, cookie sheet,

or metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the ames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned or

spread the re.

3. DO NOT USE WATER, including wet dishcloths or towels

- violent steam explosion will result.

4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher and you

already know how to operate it.

B. The re is small and contained in the area where it started. C. The re department is being called. D. You can ght the re with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust haz-

ardous or explosive materials and vapors.

2. For best capture of cooking impurities, range hood should be

mounted so that the top of the hood is 24”-30” [or applicable dimension depending on hood height and test height] above the cooking surface.

3. Read specication label on product for information and re-

quirements.

NOTE If hood is to be installed non-ducted:

Purchase a set of (2) non-ducted lters from your

local distributor or retailer and attach them to the

aluminum mesh lters.

Installer: Leave this manual with the homeowner.

Homeowner: Cleaning, Maintenance and Operating

instructions on page 2.

MODELS NS130BL • NS130SS • NS130WW

SOFFIT

24" - 30" ABOVE COOKING SURFACE

CABINET

3¼" X 10" DUCT (For horizontal discharge)

WALL CAP

ROOF CAP

3¼" X 10" or

7" ROUND DUCT

(For vertical

discharge)

HOUSE WIRING (Top or Back of hood)

HOODHOOD

VERTICAL DUCT

ACCESS HOLE

¾"

5¼"

CENTER

LINE

HOOD MOUNTING SCREWS (5)

ELECTRICAL

ACCESS HOLE

(in cabinet bottom)

WOOD SHIMS

(recessed-bottom

cabinets only)

CABINET FRONT

CABINET BOTTOM

15¼" (36" hood)

4½"

15¼" (36" hood)

12¼" (30" hood)

NS136BL • NS136SS • NS136WW

Page 2

CLEANING & MAINTENANCE

For performance, appearance, and health reasons, clean lter,

fan and grease-laden surfaces. Use only a clean cloth and mild detergent solution on stainless and painted surfaces. Clean all-

metal lters in the dishwasher.

The motor is permanently lubricated and never needs oiling. If

the motor bearings make excessive or unusual noise, replace the motor with the exact service motor. The impeller should also

be replaced. Use 120 V, 50 W, shielded halogen bulbs - MR16 or PAR16 with

GU10 base. Purchase bulbs separately.

TAB

LIGHT SWITCH

This 3-position rocker switch turns lights ON and OFF and controls their intensity.

Press left side of rocker (1) to turn lights ON to low intensity. Press right side of rocker (2) to turn lights ON to high intensity. Set rocker to middle position (0) to turn lights OFF.

PREPARE HOOD LOCATION

The grease lters, bottom panel, and blower wheel should be

cleaned frequently. Use a warm detergent solution. The grease

lters and blower wheel are dishwasher safe. Note: Some minerals, when in contact with dishwasher soap

additives, may cause lters to discolor. This discoloration

is not covered by the warranty.

To remove blower wheel: Pull wheel straight down and off of

motor. When reinstalling blower wheel, make sure TAB on wheel ts

into one hole on motor.

OPERATION

Always turn the hood ON before cooking in order to establish an

air ow in the kitchen. After turning off the range, let the hood run

for a few minutes to clear the air.

Operate the hood as follows:

BLOWER SWITCH

This 3-position rocker switch turns blower ON and OFF and controls blower speed.

Press left side of rocker (1) to turn blower ON to low speed. Press right side of rocker (2) to turn blower ON to high speed. Set rocker to middle position (0) to turn blower OFF.

1 Determine whether hood will discharge vertically (3¼” x

10” or 7” Round), or horizontally (3¼” x 10” only). For ver-

tical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitons and elbows.

2 Use the proper diagram below, for placement of ductwork

and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole.

Note the extra wood shim and mounting screw near

the cabinet front, 2-3/8” to the right of the cabinet center line.

3¼” X 10”

VERTICAL DUCTING

3¼” X 10”

CABINET BOTTOM

CABINET FRONT

HORIZONTAL DUCT

ACCESS HOLE

5¼"

HOOD

MOUNTING

SCREWS (5)

ELECTRICAL

ACCESS HOLE

(in wall)

3½"

CENTER

LINE

WOOD SHIMS

(recessed-bottom

cabinets only)

15¼" (36" hood)

12¼"

(30" hood)

15¼" (36" hood)

12¼" (30" hood)

ELECTRICAL

ACCESS HOLE

(in cabinet bottom)

15¼" (36" hood)

12¼" (30" hood)

HOOD MOUNTING SCREWS (5)

7-IN. ROUND

DUCT ACCESS

HOLE

5" 5"

HORIZONTAL DUCTING

7-IN. ROUND

DUCTING

MODELS NS130BL • NS130SS • NS130WW

NS136BL • NS136SS • NS136WW

Page 3

↑

4 Remove Bottom Cover held in place with ve (5)

screws.

↑

Note that the 7-in. round duct will need to be squeezed into an

oval shape to connect to the 7-in. oval duct plate on the hood.

PREPARE THE HOOD

3 Remove the Aluminum Filters from the hood.

↑

(2) LIFT OUT

(1)

PULL

DOWN

ALUMINUM

FILTERS

↑

DAMPER /

DUCT CONNECTOR

5 Remove Damper / Duct Connector from inside the

hood.

FOR DUCTED INSTALLATIONS - Skip to Step 10.

MODELS NS130BL • NS130SS • NS130WW

NS136BL • NS136SS • NS136WW

Page 4

RECIRCULATION

SCROLL WALL

6 NON-DUCTED INSTALLATION ONLY:

Remove Recirculation Scroll Wall from inside the hood.

TABS

▼

THUMB

SCREW

9 NON-DUCTED INSTALLATION ONLY:

Remove Recirculation Plate and Thumb Screw from plastic bag. Slide plate down onto Recirculation Grille so that Slots in plate t into Tabs on grille. Secure plate with thumb screw.

CONNECTOR

RECIRCULATION

3¼” x 10”

DAMPER /

DUCT

PLATE

SLOTS & TABS

RECIRCULATION

GRILLE

DUCT PLATE

7” OVAL

RECIRCULATION

COVER

7 NON-DUCTED INSTALLATION ONLY:

Depress the Tabs on the Recirculation Cover and push cover out through top of hood to remove it.

RECIRCULATION

GRILLE

8 NON-DUCTED INSTALLATION ONLY:

Remove Recirculation Grille from plastic bag and snap it into the opening in the top of the hood.

KNOCKOUT

OPENINGS

10 DUCTED INSTALLATION ONLY:

Remove vertical or horizontal duct knockout. Attach 3¼”

x 10” Damper/Duct Connector (if using 3¼” x 10” duct)

or 7” Oval Duct Plate ** (if using 7-inch round duct) over the knockout opening.

Note that the 7-in. round duct will need to be squeezed into an

oval shape to connect to the 7-in. oval duct plate on the hood.

MODELS NS130BL • NS130SS • NS130WW

HO0059

HO0060

HE0059

HD0154

NS136BL • NS136SS • NS136WW

Page 5

INSTALL THE HOOD

WARNING

To reduce the risk of electrical shock, switch power off at service panel. Lock or tag service panel to prevent power from being switched on accidentally.

HOUSE

POWER CABLE

11 Run House Power Cable between service panel and

hood location. Attach power cable to hood using appropriate connector.

12 Hold the hood in position under the cabinet.

For ducted installations: Make sure the damper / duct

connector enters the ductwork and that the damper opens and closes freely.

13 Tighten all 5 mounting screws completely to secure the

hood to the cabinet.

COMPLETE INSTALLATION

15 Reinstall Bottom Cover using 5 screws.

(2) ROTATE

CLOCKWISE

(1) PUSH IN

16 Install Halogen Bulbs. Use 120 V, 50 W, shielded halo-

gen bulbs - MR16 or PAR16 with GU10 base. Purchase bulbs separately.

CONNECT THE WIRING

GREEN

GROUND

SCREW

HOUSE

POWER

CABLE

14 Connect House Power Cable to range hood wiring

- BLACK to BLACK, WHITE to WHITE, and GREEN or BARE WIRE to GREEN Ground Screw.

SERVICE PARTS

KEY NO. PART NO. DESCRIPTION

1 97017397 3¼” x 10” Damper/Duct Connector * 2 97017398 7” Oval Duct Plate * 3 99526174 Recirculation Cap, Black 99526175 Recirculation Cap, White 99526146 Recirculation Grille, Black 99526147 Recirculation Grille, White 4 97017399 Rocker Switch, Black (2 Switches) 97017400 Rocker Switch, White (2 Switches) 5 99526148 Nameplate, Black 99526149 Nameplate, White

6 97017434 Recirculation Deector for 30” Hood,

Black *

97017435 Recirculation Deector for 30” Hood,

White *

97017436 Recirculation Deector for 36” Hood,

Black *

97017437 Recirculation Deector for 36” Hood,

White * 7 99526176 Recirculation Scroll Wall, Black 99526177 Recirculation Scroll Wall, White 8 97017403 Lamp Socket Holder Kit (Includes RH & LH Socket Holder, Trim Ring, Socket, & Splice Connectors) 9 97017404 Motor Mounting Bracket * 10 97017405 Motor * 11 97017406 High Speed Motor Capacitor * 12 97017407 Low Speed Motor Capacitor * 13 97017408 Blower Wheel (Includes Mounting Ring) 14 99526154 Blower Wheel Mounting Ring 15 97017409 Bottom Cover, Black, for 30” Hood * 97017410 Bottom Cover, White, for 30” Hood * 97017411 Bottom Cover, Black, for 36” Hood * 97017412 Bottom Cover, White, for 36” Hood * 16 97017413 Non-duct Filter Kit for 30” Hood (2 Filters & 8 Filter Clips) 97017414 Non-duct Filter Kit for 36” Hood (2 Filters & 8 Filter Clips) 17 97017415 Filter Kit for 30” Hood (2 Filters) 97017416 Filter Kit for 36” Hood (2 Filters) ** 97017417 Parts Bag

MODELS NS130BL • NS130SS • NS130WW

NS136BL • NS136SS • NS136WW

Page 6

* Includes hardware ** Not illustrated Order replacement parts by PART NO. - not by KEY NO.

Replacement parts can now be ordered on our website. Please visit us at www.nutone.com.

WARRANTY

MODELS NS130BL • NS130SS • NS130WW

NS136BL • NS136SS • NS136WW

Page 7

99526145B

+ 14 hidden pages