Numark N-Wave 580L User Guide
User Guide
English ( 3 – 5 )
Guía del usuario
Español ( 6 – 8 )
Guide d’utilisation
Français ( 9 – 11 )
Guida per l’uso
Italiano ( 12 – 14 )
Benutzerhandbuch
Deutsch ( 15 – 17 )
Appendix
English ( 18 )
User Guide (English)
Introduction
Box Contents
(2) N-Wave 580L Speakers
1/4” (6.35 mm) TRS Audio Connection Cable
4-Pin LED Connection Cable
RCA Audio Cable
Power Cable
User Guide
Safety & Warranty Manual
Support
For the latest information about this product (system requirements, compatibility information,
etc.) and product registration, visit numark.com.
For additional product support, visit numark.com/support.
Quick Start
Important: Ensure that high-quality, shielded audio cables are used away from sources of
electromagnetic interference.
Before turning on the power of N-Wave 580L’s right speaker, do the following:
1. Ensure the volume control on N-Wave 580L’s right speaker is turned down.
2. Connect N-Wave 580L’s left and right speakers with the included 1/4” (6.35 mm) audio
connection cable and 4-pin LED connection cable.
3. Connect any audio sources (such as an audio interface, mixer, etc.) to the inputs on NWave 580L’s right speaker. Power on the audio sources.
4. Connect the included power cable to the power input on N-Wave 580L’s right speaker,
and then plug the other end of the power cable into an outlet.
5. Flip the power switch on N-Wave 580L’s right speaker to the “on” position.
6. Adjust the volume control on the front panel of N-Wave 580L’s right speaker.
3
Setup
Placement
Left Speaker
Listener
The speakers and listener should be
at the three corners of an equilateral
triangle.
Height
Right Speaker
The placement of your speakers has a huge
impact on how well they will perform in your
studio. Although nearfield studio monitors are
designed to be more forgiving when it comes to
placement, you should do your best to make sure
they form an equilateral triangle relative to your
head. In other words, make sure that each
speaker is equally distant from both your head as
well as the other speaker. Once each speaker has
been placed, rotate the speakers slightly so that
the drivers are pointing toward the listener.
Take a look at the diagram on the left. Notice that
the distance from the listener’s head to each
speaker is the same as the distance between the
left and right speakers. Also note that the
speakers are turned slightly so that the drivers are
facing the listener. This is an ideal setup but if it is
not practical (or possible) to do this, try to match
this setup as closely as possible.
The ideal height for N-Wave 580L is so that the
speaker is parallel to the ground and that the
midpoint of the woofer and tweeter is at ear-height.
The diagram to the right demonstrates the ideal
placement height of the speakers relative to the
listener. Notice that the listener’s ears are directly
between the woofer and tweeter.
4
Features
Rear Panel
10
2
8
6
4
9
5
3
1
7
1. Power Input: Use a power cable (included) to connect this to a power outlet.
2. Power Switch: Use this switch to power N-Wave 580L on or off. Turn on N-Wave 580L
after all input devices have been connected.
3. Speaker Link (Right): This is the audio connection to the left speaker. Use the included
1/4” (6.35mm) TRS cable to connect the right speaker to the left speaker.
4. Speaker Link (Left): This is the audio connection from right speaker. Use the included
1/4” (6.35mm) TRS cable to connect the left speaker to the right speaker.
5. Output to Left LED: This is the LED connection to the left speaker. Use the included 4-pin
LED connection cable to connect the right speaker to the left speaker.
6. Input from Right LED: This is the LED connection from right speaker. Use the included 4pin LED connection cable to connect the left speaker to the right speaker.
7. LED Mode: Press this button to cycle through the available light modes:
• Off: The lights will be off.
• Pulsate Mode: The audio signal will cause the lights to pulse. When there is no
audio signal, the lights will enter Slow Cycle Mode.
• Slow Cycle Mode: The lights will illuminate and change colors regardless of the
music playing.
8. Inputs (RCA): Connect your audio interface, mixer, etc. to these inputs, using a standard
RCA cable.
9. Input (1/4” / 6.35 mm TRS): Connect your audio interface, mixer, etc. to this input, using
standard 1/4” (6.35 mm) TRS cables.
10. Bass Boost: This two-position switch allows you to boost the speakers’ bass frequencies.
11. Vol (front panel, not pictured): Use this knob to adjust the speaker’s volume.
5
Guía del usuario (Español)
Introducción
Contenido de la caja
(2) altavoces N-Wave 580L
Cable de interconexión audio 6,35 mm (1/4 pulg.) TRS
Cable de interconexión LED de 4 patillas
Cable de audio RCA
Cable de alimentación
Guía del usuario
Manual sobre la seguridad y garantía
Soporte
Para obtener la información más completa acerca de este product (los requisitos del sistema,
compatibilidad, etc) y registro del producto, visite numark.com.
Para soporte adicional del producto, visite numark.com/support.
Inicio rápido
Importante: Asegúrese de utilizar cables de audio blindados de alta calidad y alejados de las
fuentes de interferencia electromagnética.
Antes de encender el altavoz derecho del N-Wave 580L, realice lo siguiente:
1. Asegúrese de que el control de volumen del altavoz derecho del N-Wave 580L esté
ajustado al mínimo.
2. Conecte los altavoces izquierdo y derecho del N-Wave 580L mediante el cable de
interconexión audio de 6,35 mm (1/4 pulg.) y el cable de interconexión LED de 4 patillas
incluidos.
3. Conecte las fuentes de audio (tales como una interfaz de audio, un mezclador, etc.) a las
entradas del altavoz derecho del N-Wave 580L. Encienda las fuentes de audio.
4. Conecte el cable de alimentación incluido a la entrada de alimentación del altavoz derecho
del N-Wave 580L y después enchufe el otro extremo del cable de alimentación a una toma
de corriente.
5. Coloque el interruptor de encendido del altavoz derecho del N-Wave 580L en la posición
de encendido.
6. Ajuste el control de volumen del panel frontal del altavoz derecho del N-Wave 580L.
6
Loading...