ModeJ No. NTEL7706.1
Serial No.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are corn=
mitted to providing compJete
customer satisfaction, tf you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
USER'S
CALL TOLL-FREE:
1-888-825-2588
Mono-Fri. 6 a,m,-6 pomoMST
Sat. 8 a.m.-5 p.m. MST
ON THE WEB:
www.nordictrackservice.com
Read alJ precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference. new products, prizes,
fitness tips, and much more!
800
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS ................................................................ 3
BEFORE YOU BEGIN ...................................................................... 4
ASSEMBLY ............................................................................... 5
HOW TO USE THE ELLIPTICAL EXERCISER .................................................. 10
MAINTENANCE AND TROUBLESHOOTING ................................................... 18
CONDITIONING GUIDELINES ............................................................... 19
PART LIST .............................................................................. 20
EXPLODED DRAWING .................................................................... 22
HOW TO ORDER REPLACEMENT PARTS ............................................. Back Cover
LIMITED WARRANTY .............................................................. Back Cover
NordicTrack is a registered trademark of ICON IP, Inc,
2
mMPORTANT PRECAUTIONS
AWARNING: To reduce the riskOf serious injury, read the following important precau-
tions before using the ellipticaJ exerciser.
1. Bead all instructiens in this manual and alJ
warnings on the elliptical exerciser before
using the elliptical exerciser. Use the eHi pti-
eal exercise onJy as described in this
manual
2. it is the responsibility of the owner to ensure
that aH users of the elliptical exerciser are
adequatemy informed of aH precautions.
3.
The elliptical exereieer is intended for
home use only. Do not use the elliptical
exerciser in a commercial, rentaJ, or institu-
tional setting.
4o Keep the eHipticaJ exerciser indoors, away 11. Keep your back straight while usingthe chip-
from moisture and duet. Place the elliptical
exerciser on a tevel eurfaee, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around the elliptical exerciser to mount, dis-
mount, and use it.
5. mnspeet and properly tighten aH parts regu_
Jar|y. RepJace any worn parts immediately.
6. Keep children under 12 and pets away from
the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 300 pounds.
8. Wear appropr}ate exercise clothes while
using the elliptical exercieero Always wear
athJetie shoes for foot protection while exer-
cising.
9. Hold the handgrip pulse sensors or the upper
body arms when mounting, dismounting, or
using the eJHptical exerciser.
10. The puJse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The puJse sensor is
................................ determin-
ing heart rate trends in general.
tieal exerciser: do not arch your back.
12. if you feel pain or dizziness while exereisi rig,
stop immediately and cool down.
13. When you stop exercising, allow the pedaJe
to slowly come to a stop.
14. The warning decals shown on page 4 have
been placed on the eHiptieaJ exerciser in the
locations shown, if a decal is missing or
iHegible_ call the toll-free tebphone number
on the front cover of this manual and order
a free replacement decal Apply the deeaJ in
the {oeation shown.
AWARNmNG: Beforebeg nn ogth soranyexerciseprogram,coneultyourphysician,
This is especially important for persons over the age of 35 or persons with pre-existing health probe
leme. Bead aH instructions before using. _CON assumes no responsibility for persona_ iniury or
property damage sustained by or through the use of this product.
BEFORE YOU BEGIN
Thank you for purchasing the revolutionary
NordicTrack:" AUDIOSTRIDER 800 elliptical exerciser,
The AUDIOSTRIDER 800 elliptical exerciser provides
a wide array of features designed to make your work=
outs at home more effective and enjoyable--and
when you're not exercising, the unique eHipticaJexer=
ciser can be folded out of the way,
For your benefit, read this manual carefulJy before
you use the ellipticaJ exerciser. If you have ques=
Upper Body Arm
Stereo Speakers
Water Bottle Holder*
Storage Magnet
tions after reading this manual, pJease see the front
cover of this manual To heJp us assist you, note the
product model number and serial number before con-
tacting us. The model number is NTEL7706,1, The
serial number can be found on a decal attached to the
elliptical exerciser (see the front cover of this manuaJ
for the location of the decal),
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below,
Fan
Console
se Sensor
FRONT
clear of
_s area.
REAR
Pedal Disk
Handle
Leveling Foot
and
IncJine Knob
Ramp
Wheel
Pedal
Pedal Arm Latch
Latch Button
RIGHT SiDE
*No water bottJe is included
4
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included he× keys and your own phillips screwdriver and rubber
mallet C-I---L-: _ "
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses
below each drawing is the key number of the part, from the PART LESTon pages 20 and 21. The number follow-
ing the parentheses is the quantity needed for assembly. Note: Some small parts may have been preassem-
bled. tf a part is not in the parts bag, check to see if it has been preassembJed.
f ....
]
....... J
M10 x 25mm M10 Curved Link Arm
Washer (87)-2 Washer (99)-4 Spacer (74)-4
M6 Split Washer
(102)-8
M8 Split
Washer (101)-4
M8.5 x 16mm x
1.5mm Washer
(103)-6
M4 x 16mm
Wave Washer Screw (97)-16
(100)-2
M8 x 15mm Button
Screw (106)-10
1, See HOW TO FOLD AND UNFOLD THE
ELLIPTICAL EXERCISER on page 11 and
unfold the elliptical exerciser.
While another person lifts the front of the
Frame (1), attach the Front Stabilizer (4) to the
Frame with two M10 x 93mm Button Screws
(82) and two M10 Curved Washers (99).
M8 x 20mm Button
Screw (107)-4
M6 x 35mm
Screw (109)-4
M8 x 25mm Button
Screw (110)-2
M10 x 93mm Button Screw (82)-4
M6 x 62mm
Screw (108)-4
M10 x 20mm Button
Screw (111)-2
4
2, While another person lifts the Folding Frame (2),
attach the Rear Stabilizer (3) to the Folding
Frame with two M10 x 93mm Button Screws (82)
and two M10 Curved Washers (99),
Next, tighten the Center Foot (95) into the
Frame (1),
Attach the Front Ramp Cover (6) to the
Ramp (5) with four M4 x 16ram Screws (97),
Slide an M10 x 25mm Washer (87) onto an
M10 x 20mm Button Screw (111). Tighten the
Button Screw into one end of the Ramp
Axle (72), Apply a small amount of the included
grease to the Ramp Axle,
95
82
62
Orient the Ramp (5) as shown, Align the lower
end of the Ramp with the welded tube on the
Frame (1), Insert the Ramp Axle (72) into the
Ramp and the welded tube, Then, pull the Ramp
Knob (9), lower the Ramp, and engage the
Ramp Pin (62) in one of the three adjustment
hoJes in the front of the Frame,
Slide an M10 x 25mm Washer (87) onto an
M10 x 20mm Button Screw (111), Tighten the
Button Screw into the open end of the Ramp
AxJe (72),
97
Adjustment
87 111
72
8\
Grease
6
Identify the Left Pedal (34) and the Left Pedal
Arm (32), which are marked with stickers.
Attach the Left Pedal (34) to the Left Pedal
Arm (32) with two M6 x 62ram Screws (108),
two M6 x 35mm Screws (109), and four M6
Split Washers (102).
Attach the Right PedaJ (not shown} to the
Right Pedal Arm (not shown) in the same
way.
Insert the Roller (38) on the Left Pedal Arm (32)
and the Roller on the Right Pedal Arm (33) into
the sides of the Ramp (5).
Attach the Rear Ramp Cover (7) to the
Ramp (5) with two M4 x 16ram Screws (97).
See the inset drawing. Lift the Pedal Arm
Latch (41) on the Left Pedal Arm (32), and set
the end of the Left Pedal Arm on the left Crank
Bushing Sleeve (54). Release the Pedal Arm
Latch, and make sure that the Left Pedal Arm is
securely connected to the Crank Bushing
Sleeve.
Connect the Right Pedal Arm (not shown} to
the right Crank Bushing Sleeve (not shown)
in the same way.
32
34
/
102
U
109
102
97
7
33
/
5
32
38
41
7
While another person holds the Upright (10)
6. 6
near the Frame (1), connect the Upper Wire
Harness (65) to the Lower Wire Harness (64).
Carefully insert the Upright (10) into the
Frame (1); be carefuJ not to damage the Wire
Harnesses (84, 85). Attach the Upright with four
M8 x 20mm Button Screws (107) and four M8
Split Washers (101 ).
Be carefuJ not
to damage the
Wire Harnesses
(84, 65) during
this step.
Attach the Left Upper Body Arm (22) to the left
Upper Body Leg (24) with three M8 x 15mm
Button Screws (106).
Attach the Right Upper Body Arm (23) in the
same way.
/,//
///
_10
i
i
Hold the Left Rear Upper Body Cover (26) and
the Left Front Upper Body Cover (27) around
the left Upper Body Leg (24). Attach the Upper
Body Covers with five M4 x 16mm Screws (97).
Attach the Right Rear Upper Body Cover (28)
and the Right Front Upper Body Cover (29)
in the same way.
29
97_
27
Loading...