The Service Box JBU–5 is used for power supply and current calibration.
Also flash loading and functional tests.
Product Code
Service Box JBU–5:0770120
View of JBU–5
Technical Documentation
PNS–5
”Pin set” PNS–5 is a spare part for Service Box JBU–5
Product Code
Pin set PNS–5:0750122
Page 4
Original 08/98
PAMS
NSE–6
Technical Documentation
Module Jig MJS–6
The Module Jig MJS–6 is used for repair of system/RF module. *
Product Code
Module Jig MJS–6:0770121
View of MJS–6
Service Tools
*Note: The nominal supply voltage for MJS–6 is +3.6 V.
Original 08/98
The supply voltage must not exceed +5.0 V.
Page 5
NSE–6
PAMS
Service Tools
Battery Adapter BDS–6
The Battery Adapter BDS–6 is used along with an external battery
capacity meter to check battery capacity.
Note that Li–ion batteries have an internal protection circuit to prevent
deep discharge.
Product Code
Battery Adapter BDS–6:0750121
View of BDS–6
Technical Documentation
Page 6
Original 08/98
PAMS
NSE–6
Technical Documentation
Flash Loading Adapter FLA–5 (Sales Pack)
The Flash Loading Adapter FLA–5 is used with the Service Battery BBD–3
and Service Cable SCH–5. Power is supplied to FLA–5 from the Flash
Security Box TDF–4 via the DC cable PCC–1, (The PCC–1 cable can be
replaced with a Travel Charger ACH–6), and is connected to the Flash
Prommer FPS–4S with the cable AXS–5.
The sales pack includes:
– Flash Loader Adapter FLA–50770085
– Service cable SCH–50730098
– D15 – D15 Cable AXS–50730091
– Installation software for FPS–48400041
Sales package code
Flash Loading Adapter FLA–5:0080178
View of FLA–5
Service Tools
Original 08/98
Page 7
NSE–6
PAMS
Service Tools
Flash Prommer FPS–4S (Sales Pack)
The Flash Prommer FPS–4S is used to update the main software of the
phone. Updating is done by first loading the new MCU software from the
PC to the flash prommer, and then loading the new SW from the prommer
to the phone. When updating more than one phone in succession, the
MCU software only needs to be loaded to the prommer once.
The sales pack includes:
– Flash Prommer FPS–40750090
NOTE: When flashing NSE–6 phone, FPS–4 must be upgraded using
1 Mb SRAM module (0200742).
Original 08/98
PAMS
NSE–6
Technical Documentation
Security Box TDF–4
The Security Box TDF–4 is required for updating MCU software, and infra
red testing.
Note 1:TDF–4 is delivered in de–activated mode. Fill in the enclosed
Activation Request Form, and fax to NMP Salo to get the
activation code
Note 2:The infra red module JLP–1 is not included in the TDF–4 sales
package
Product Code
Security Box TDF–4:0770106
View of TDF–4
Service Tools
Original 08/98
Page 9
NSE–6
PAMS
Service Tools
Service Audio Box JBA–4
The Service Audio Box JBA–4 is used between the Service Cable SCH–5,
MBUS Cable DAU–9S, and Audio Cable ADS–1.
Product Code
Service Audio Box JBA–4:0770094
View of JBA–4
Technical Documentation
Page 10
Original 08/98
PAMS
NSE–6
Technical Documentation
Audio Cable ADS–1
Audio cable is an adapter routing AF signals (MIC/EAR) from 8 pin
modular connector to two BNC connectors. It is used to connect JBA–4,
SCH–5, and DAU–9S.
Product code
Audio Cable ADS–1:0730011
View of ADS–1
Service Tools
Original 08/98
Page 11
NSE–6
PAMS
Service Tools
D15–D15 Cable AXS–5
The D15–D15 Cable AXS–5 is used to connect two 15 pin D connectors.
e.g. between FLA–5 and FPS–4S.
Product Code
D15–D15 Cable AXS–5:0730091
View of AXS–5
Technical Documentation
Page 12
Original 08/98
PAMS
NSE–6
Technical Documentation
DC Charging Cable PCC–1
The DC Cable PCC–1 is used e.g. to connect FLA–5 and TDF–4.
Product Code
DC Cable PCC–1 (with modular RJ connector):0730053
DC Cable PCC–1B (with banana connectors):0770050
View of PCC–1
Service Tools
Original 08/98
Page 13
NSE–6
PAMS
Service Tools
DC Cable SCB–3
The DC Cable SCB–3 is used to connect the Service Battery to the
charger connection Vin of the phone when doing the charger calibration
service procedure.
Product Code
DC Cable SCB–3:0730114
View of SCB–3
Technical Documentation
Page 14
Original 08/98
PAMS
NSE–6
Technical Documentation
MBUS Cable DAU–9S
The MBUS Cable DAU–9S has a modular connector, and is used with the
service Audio Box JBA–4, or a modular T–adapter.
Product Code
MBUS Cable DAU–9S:0730108
View of DAU–9S
Service Tools
Original 08/98
Page 15
NSE–6
PAMS
Service Tools
Power Cable PCS–1
The Power Cable PCS–1 is used to connect the module jigs JBT–1 and
JBS–19 to an external power supply. Can be used with FPS–4 also.
Product Code
Power Cable PCS–1:0730012
View of PCS–1
Technical Documentation
Page 16
Original 08/98
PAMS
NSE–6
Technical Documentation
Audio Cable SCA–5
Audio cable is an adapter routing AF signals (MIC/EAR) from phones
headset connector to the service box JBU–5.
Product code
Audio Cable SCA–5:0730136
View of SCA–5
Service Tools
Original 08/98
Page 17
NSE–6
PAMS
Service Tools
Service Cable XCM–5
XCM–5 is a modular cable for flashing.
Product code
Service Cable XCM–5:0730142
View of XCM–5
Technical Documentation
Page 18
Original 08/98
PAMS
NSE–6
Technical Documentation
Modular T–adapter
The modular T–adapter is a suitable branching unit to provide the needed
parallel modular connections.
Product Code
Modular T–adapter:4626134
View of Modular T–adapter
Service Tools
Original 08/98
Page 19
NSE–6
PAMS
Service Tools
SW Security Device PKD–1
SW security device is a piece of hardware enabling the use of the service
software when connected to the parallel (LPT) port of the PC. Whitout the
dongle present it is not possible to use the service software. Printer or any
such device can be connected to the PC through the dongle if needed.
Caution: Make sure thet you have switched off the PC and the printer
before making connections!
Caution: Do not connected the PKD–1 to the serial port. You may
damage your PKD–1!
Product Code
SW Security Device PKD–1:0750018
View of SW Security Device
Technical Documentation
Page 20
Original 08/98
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.