RH-21Company Confidential
Service ToolsNokia Customer Care
Page 4 2004 Nokia Corporation.Issue 2 07/2004
Page 5
Company Confidential RH-21
Nokia Customer CareService Tools
Service Tools
3520
PhotoCodeService ToolCodeDescription
MJ-8Module Jig0770522This jig allows phone
PWB-level service and
troubleshooting. Electric currents should be
protected against
over-voltage and
over-current.
FLS-4SPOS Flash Adapter0080543The Point of Sale
(POS) flash is a lowcost software upgrade
tool. This requires the
XCS-1 cable and
ACP-8U for operation.
FPS-8Flash Prommer0080321The Flash Prommer
FPS-8 is used for
flash.
FPS-8CHeavy Flash Prommer0080396The Heavy Flash
Prommer FPS-8C is
used for heavy parallel flashing.
Issue 2 07/2004 2004 Nokia Corporation.Page 5
Page 6
RH-21Company Confidential
Service ToolsNokia Customer Care
PhotoCodeService ToolCodeDescription
JBV-1Docking Station0770298The Docking Station
and the Docking Station Adapter (DA-32)
are needed for Mbus,
Fbus, RF, and audio
connections.
This setup allows connection between flash
prommers. When the
audio box is connected, it has to be
connected to the
phone’s audio connector.
DA-32Docking Station
Adapter
CPL-1Coupler0770287The coupler has been
JBA-8Audio Box0770320The Audio Box is
0770870The Docking Station
can be powered by
FPS-8 or external
power supply.
developed for antenna
go/no go testing.
needed for audio connections. The box
must support DCT4
Janette audios. JBA-8
provides an interconnection between the
phone’s system connector (XEAR, XMIC)
through a fixed audio
cable and audio tester
with a BNC-BNC
coax. Connection to a
PC can be made with
the service battery,
through a DAU-9
cable.
Page 6 2004 Nokia Corporation.Issue 2 07/2004
Page 7
Company Confidential RH-21
Nokia Customer CareService Tools
PhotoCodeService ToolCodeDescription
SF-35Flash Adapter0770868SF-35 allows a con-
tinuous maximum
power supply for the
phone from an external power supply, the
ACP-8.
RJ-15Soldering Jig0770611RJ-15 is used to hold
the PWB during repair
and troubleshooting.
AXP-8Printer Cable0730298The Parallel Printer
Cable connects the
parallel connector of
the PC and the parallel input of the FPS-8.
AXS-4D9-D9 Cable0730090The AXS-4 D9-D9
service cable is used
to connect two 9-pin
connectors (e.g.,
between PC and
FPS-8). AXS-4 length
is 2 meters
ADS-3Audio Cable0730197The audio cable con-
nects to the audio box
JBA-6.
ADS-4Audio Cable0730222ADS-4 is the service
cable between the
phone and the service
audio box.
Issue 2 07/2004 2004 Nokia Corporation.Page 7
Page 8
RH-21Company Confidential
Service ToolsNokia Customer Care
PhotoCodeService ToolCodeDescription
CA-5SDC Cable 0730283The DC Cable CA-5S is
used to connect the
docking station to the
charger connection
(Vin) of the phone to
conduct the charger
calibration service
procedure.
DAU-9SMbus Cable0730108The Mbus Cable has a
modular connector
and is used with the
service audio box
JBA-4 or a modular
T-adapter.
PCS-1Power Cable0730012The Power Cable
PCS-1 is used to connect the service tools
(JBV-1, DA-32) to an
external power supply.
XRS-6RF Cable0730231The XRS-6 cable con-
nects a service tool
and RF measurement
equipment.
XCS-4Mbus/Fbus Cable0730178The XCS-4 Service
Cable is a modular
cable for flashing
DCT4 products.
Page 8 2004 Nokia Corporation.Issue 2 07/2004
Page 9
Company Confidential RH-21
Nokia Customer CareService Tools
PhotoCodeService ToolCodeDescription
PKD-1SW Security Device0750018SW security device
PKD-1 is hardware
device that, when
connected to the parallel (LPT) port of the
PC, enables the use of
the service software.
Without the dongle
present, it is not possible to use the service software. Printers
or other peripheral
devices can be connected to the PC
through the dongle, if
needed.
Caution: Make sure
that you have
switched off the PC
and the printer before
making connections!
Caution: Do not connect the PKD-1 to the
serial port. You may
damage your PKD-1!
SA-12
XRS-11
GAC-8/
GAC-9K
RF Probe Support
RF Probe
Adapter0080834The GAC-8/GAC-9K
0770623
0630265
The RF Cable is used
for connection to the
RF output of the PWB.
The XRS-11 Cable is
used together with
the SA-12 to ensure a
good connection.
adapter is needed for
proper RF connection
when using the DA-
32. The adapter allows
galvanic connections
to assembled handset
RF switches. The
adapter permits the
handset to be connected to RF measuring and test
equipment during test
and repair and can be
used with covers on or
off.
NOTE: GAC-8 must be
used with GAC-9k.
Issue 2 07/2004 2004 Nokia Corporation.Page 9
Page 10
RH-21Company Confidential
Service ToolsNokia Customer Care
Flashing and Testing Setups
FPS-8 Flash Prommer for Heavy Flash
The FPS-8 flash prommer is used for heavy flashing. The sales pack product code is
0080321.
FPS-8C Flash Prommer for Heavy Parallel Flash
The FPS-8C flash prommer is used for heavy parallel flashing. The sales pack product
code is 0080396.
Page 10 2004 Nokia Corporation.Issue 2 07/2004
Page 11
Company Confidential RH-21
Nokia Customer CareService Tools
User Instructions
SF-35
Follow these instructions to avoid damage to the adapter or the phone.
Note: Using the adapter in any way other than described here may harm the important pins and connectors of the adapter.
1Place the adapter in your left hand and the phone in your right hand.
2Align the battery connecter with the battery contacts of the adapter. Gently
press the phone onto the adapter (see following picture).
Issue 2 07/2004 2004 Nokia Corporation.Page 11
Page 12
RH-21Company Confidential
Service ToolsNokia Customer Care
3Press the upper end of the handset down onto the adapter until the locking
mechanism engages.
To remove adapter, dis-engage the locking mechanism by pulling back on the lever. Follow the reverse order as described in steps 1 through 3.
Page 12 2004 Nokia Corporation.Issue 2 07/2004
Page 13
Company Confidential RH-21
Nokia Customer CareService Tools
DA-32
Follow these instructions to avoid causing any damage to the adapter or the phone.
Note: Using the adapter in any other way may harm the important pins and connectors of the adapter.
1Place the adapter in your left hand and the phone in your right hand.
2Let the other edge of the phone down in place.
Issue 2 07/2004 2004 Nokia Corporation.Page 13
Page 14
RH-21Company Confidential
Service ToolsNokia Customer Care
3Press down the upper end of the phone with your finger until the locking mecha-
nism engages.
4To remove the phone from the adapter, dis-engage the locking mechanism by
pulling back on the lever. Follow the reverse order as described in steps 1
through 3.
Page 14 2004 Nokia Corporation.Issue 2 07/2004
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.