Nilfisk PHH15002A User Manual
Dear Owner,
Congratulations! Thank you for purchasing this new heater manufactured by a division of Marley
Engineered Products. You have made a wise investment selecting the highest quality product in the heating industry. Please carefully read and follow the installation and maintenance directions shown in this
manual. You should enjoy years of efficient heating comfort with this product from Marley Engineered
Products... the industry’s leader in design, manufacturing, quality and service.
... The Employees of
Marley Engineered Products
Read Carefully - This instruction sheet contains vital informa-
tion for the installation, use and efficient operation of the heater.
Carefully read the manual before installation, operation, or cleaning
of the heater. Failure to adhere to the instructions could result in
fire, electric shock, death, serious personal injury, or property damage. Save these instructions and review frequently for continuing
safe operation and instructing future users.
1.
Do Not operate heater without both support leg extensions
properly installed.(See Fig. 1) Do not allow heater to operate
in any position except as shown in this manual.
2.
Do Not install heater against combustible low-density cellulose
fiberboard surfaces.
3. Heater is not to be located below an electical convenience
outlet.
4. When moving, allow heater to cool then grasp heater along the
top of the back of the heater.
5. This heater is to be used on the floor only. Do not use on shelf,
table, bed, or any location except the floor.
6. This heater is a major electrical appliance and requires
adequate electrical power for safe use. The outlet to which the
heater is connected must be a 120 volt , AC circuit protected by a 15
or 20 amp fuse or circuit breaker in accordance with the
National and Local Electric Codes. No other major electrical
appliance can be operated on the same circuit as the heater.
7. To prevent electric shock match wide blade of plug to wide
slot in outlet and insert fully.
8. Plug heater power cord directly into the electrical outlet.
Never use an extension cord with this heater.
9. Heater surfaces may reach high temperatures during use.
Keep all electrical cords, drapes, bedding materials, and
other furnishings away from heater. Never place anything on
top of heater. It is recommended that a space of at least
twelve (12) inches be maintained around heater.
10.
Do Not store or use gasoline or other liquids with flammable
vapors in the vicinity of this heater.
11.
Do Not use this heater near water (as in a wet basement or near
swimming pools) or in a very humid environment.
12. When heater is not to be used for an extended time, turn off
heater by rotating thermostat knob to “OFF” position and
unplug heater. Wrap power cord to prevent damage and
move heater to safe place for storage.
13. Keep this heater clean.
Do not allow dirt or dust to accumulate
around element fins or the outlet grille area. See Cleaning
Instructions section of this manual.
14. If this heater or its power cord becomes damaged or malfunctions in any way, unplug heater, discontinue use, and have unit
repaired by a reputable repair service.
WARNING
OWNER’S MANUAL
FILE #E37116
The Choice of Professionals
PORTABLE ELECTRIC
HYDRONIC BASEBOARD
HEATER
MODEL
NO.
VOLTS WATTS AMPS
1500/750
BTU/HR
PHH15002A 120V
12.5/6.3
5120/2560
!
SAVE THESE INSTRUCTIONS
Heater Assembly
1. After removing the heater from its carton, carefully inspect
it for possible shipping damage. Return damaged units to
point of purchase.
2. Remove plastic support leg extensions from packaging. Line
up the slots and slide extension into end panels as shown.
(See Figure 1).
Heater Operations
1. The PHH15002 is provided with a POSITIVE OFF
thermostat. In addition to the thermostat, the PHH15002
has a LO/HI heat selection switch.
2. Operation is as simple as A-B-C:
a. Plug heater power supply cord into 120 volt outlet
(see warnings 1, 3, 4, 5 & 6). The rocker switch on
the PHH 15002 will illuminate, indicating power is on.
b. Move heat selection switch to the “LO” position for
750 watts or to the “HI” position for 1500 watts.
c. Rotate the thermostat knob to the right until it stops.
NOTE: You may notice a new smell coming from your
heater during initial use. It should go away within the first
few hours of operation.
3. Allow the heater to operate normally until the room
temperature is comfortable to you. Then simply rotate the
thermostat knob to the left until the thermostat clicks. The
thermostat will then automatically turn your heater on and
off to maintain the room temperature.
4. To adjust the room temperature, rotation of the thermostat
knob to the right will increase the heater output while
rotation of the thermostat knob to the left will decrease the
output. The numbers on the thermostat knob are for
reference only and may help you in setting and adjusting
the heater output for your comfort.
5. To turn heater off, rotate the thermostat knob to the left until
it stops. Always unplug heater when not in use.
Cleaning Instructions
(See Warning No. 11)
1. From time to time, your heater will require cleaning to
remove dust and dirt from the element fins and outlet
air grille. Maintaining a clean heater will help the
heater operate cooler and thus safer.
2. Always turn power off and unplug heater before
cleaning.
3. Use vacuum cleaner with brush attachment to carefully
remove all dust and dirt from element fins and outlet air
grille.
NOTE: Use care not to bend fins while cleaning.
4. To clean painted heater surfaces, use damp cloth only. Do
not use waxes, etc. because they sometimes discolor
due to temperature.
LIMITED WARRANTY
All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of purchase, except the element which is warranted for 10 years after purchase. This warranty does not apply to damage from accident, misuse, or alteration;
nor where the connected voltage is more than 5% above the nameplate voltage; nor to equipment improperly installed or wired or maintained in violation of the product’s installation instructions. All claims for warranty work must be accompanied by proof of the date of installation.
The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred
to return products to Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the
nearest Marley authorized service center or the Marley Engineered Products Service Center, and we will repair or replace, at our option, at no charge
to you with return freight paid by Marley. It is agreed that such repair or replacement is the exclusive remedy available from Marley Engineered Products.
THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY
DISCLAIMED AND EXCLUDED FROM THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALLNOT BE LIABLE FOR CONSEQUENTIAL
DAMAGES ARISING WITH RESPECT TO THE PRODUCT, WHETHER BASED UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CONTRACT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328. Merchandise
returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products.
When requesting return authorization, include all catalog numbers shown on the products.
NEED TECHNICAL OR WARRANTY ASSISTANCE?
PLEASE CALL TOLL-FREE 1-800-642-HEAT.
ECR 34741
11/01
5200-2365-002
Correct
Incorrect
Figure 1
SPX Corporation
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA
Loading...