Nice Automation Flox User Manual
Flox
Receiver
Codice: ISTFLO.4852 - Rev. 03 del 22 - 06 - 2009
EN - CE CONFORMITY DECLARATION
Note - The contents of this declaration correspond to those of the
last revision available of the official document, deposited at the
registered offices of Nice S.p.a., before printing of this manual. The
text herein has been re-edited for editorial purposes.
Number: 201/FLOX Revision: 1
Nice S.p.a. - via Pezza Alta, 13, Z.I. Rustignè, 31046
Oderzo (TV) Italy, declare that all products of the FLOX
line (FLOX1, FLOX2, FLOXB2, FLOXI, FLOXI2, FLOXM,
FLOXM220) conform to the essential requisites specified
in the R&TTE 1999/5/EC Directive for the use the devices
have been manufactured for. The products are in Class 1.
Oderzo, 2thJuly 2007
Lauro Buoro
(Managing Director)
IT - DICHIARAZIONE DI CONFORMITÀ CE
Nota - Il contenuto di questa dichiarazione corrisponde a quanto
dichiarato nel documento ufficiale depositato presso la sede di
Nice S.p.a., e in particolare, alla sua ultima revisione disponibile
prima della stampa di questo manuale. Il testo qui presente è stato riadattato per motivi editoriali.
Numero: 201/FLOX Revisione: 1
Nice S.p.a. - via Pezza Alta, 13, Z.I. Rustignè, 31046
Oderzo (TV) Italia, dichiara che tutti i prodotti della linea
FLOX (FLOX1, FLOX2, FLOXB2, FLOXI, FLOXI2, FLOXM,
FLOXM220) sono conformi ai requisiti essenziali richiesti
dalla Direttiva R&TTE 1999/5/CE, per l’uso cui gli apparecchi sono destinati. I prodotti sono in Classe 1.
Oderzo, 2 luglio 2007
Lauro Buoro
(Amministratore delegato)
DE - KONFORMITÄTSERKLÄRUNG CE
Anmerkung - Der Inhalt dieser Erklärung entspricht dem in der vor
dem Druck dieser Anleitung verfügbaren, letzten Revision, der offiziellen Unterlage, die sich im Firmensitz der Nice S.p.a. befindet.
Dieser Text wurde aus Herausgebergründen überarbeitet.
Nr.: 201/FLOX Revision: 1
NICE S.p.A. - Via Pezza Alta 13, Z.I. Rustignè, 31046
Oderzo (TV) Italien erklärt, dass alle Produkte der Serie
FLOX (FLOX1, FLOX2, FLOXB2, FLOXI, FLOXI2, FLOXM,
FLOXM220) mit den wichtigsten Anforderungen der
Richtlinie R&TTE 1999/5/CE konform sind, was den Einsatz betrifft, für den die Geräte bestimmt sind. Die Produkte gehören zu Klasse 1.
Oderzo, den 2. Juli 2007
Lauro Buoro
(Der Geschäftsführer)
PL - DEKLARACJA ZGODNOŚCI CE
Uwaga - Zawartość niniejszej deklaracji odpowiada oświadczeniom znajdującym się w dokumencie urzędowym, złożonym w siedzibie firmy Nice S.p.a., a w szczególności w ostatniej korekcie dostępnej przed wydrukowaniem tej instrukcji. Tekst w niej zawarty
został dostosowany w celach wydawniczych.
Numer: 201/FLOX Wersja: 1
Nice S.p.a. - via Pezza Alta, 13, Z.I. Rustigne, 31046
Oderzo (TV) Italia, oświadcza, że wszystkie wyroby linii
FLOX (FLOX1, FLOX2, FLOXB2, FLOXI, FLOXI2, FLOXM,
FLOXM220) są zgodne z podstawowymi wymaganiami
ustanowionymi przez Dyrektywę R&TTE 1999/5/CE, w
zakresie użytkowania urządzeń zgodnie z ich przeznaczeniem. Wyroby posiadają Klasę 1.
Oderzo, dnia 2 Lipiec 2007 roku
Lauro Buoro
(Zarządca delegowany)
FR - DÉCLARATION DE CONFORMITÉ CE
Note - Le contenu de cette déclaration de conformité correspond
à ce qui est déclaré dans la dernière révision disponible du document officiel, déposé au siège de Nice S.p.a., avant l'impression
de ce guide. Le texte ici présent a été réadapté pour des raisons
d’édition.
Numéro : 201/FLOX Révision : 1
NICE s.p.a. - via Pezza Alta, 13, Z.I. Rustignè, 31046
Oderzo (TV) Italia, déclare que tous les produits de la ligne
FLOX (FLOX1, FLOX2, FLOXB2, FLOXI, FLOXI2, FLOXM,
FLOXM220) sont conformes aux exigences essentielles
de la Directive R&TTE 1999/5/CE, pour l’utilisation à
laquelle les appareils sont destinés. Les produits sont en
Classe 1.
Oderzo, 2 Juillet 2007
Lauro Buoro
(Administrateur délégué)
ES - DECLARACIÓN DE CONFORMIDAD CE
Nota - El contenido de esta declaración corresponde a aquello
declarado en la última revisión disponible, antes de la impresión de
este manual, en el documento oficial, depositado en la sede de
Nice S.p.a. En este manual, el texto ha sido readaptado por motivos de impresión.
Número: 201/FLOX Revisión: 1
Nice S.p.a. - Via Pezza Alta 13, Z.I. Rustignè, 31046
Oderzo (TV) Italia, declara que todos los productos de la
línea FLOX (FLOX1, FLOX2, FLOXB2, FLOXI, FLOXI2,
FLOXM, FLOXM220) responden a los requisitos esenciales de la Directiva 1999/5/CE Equipos Radioeléctricos y
Equipos Terminales de Telecomunicación, para el uso
previsto del aparato. Los productos son fabricados en
Clase 1.
Oderzo, 2 de Julio 2007
Lauro Buoro
(Administrador delegado)
EN - DISPOSAL OF THE PRODUCT
As indicated by the symbol on the left, disposal of
this product in domestic waste is strictly prohibited.
IT - SMALTIMENTO DEL PRODOTTO
Come indicato dal simbolo a lato, è vietato gettare
questo prodotto nei rifiuti domestici.
FR - MISE AU REBUT DU PRODUIT
Comme l’indique le symbole ci-contre, il est interdit
de jeter ce produit avec les ordures ménagères.
DE - ENTSORGUNG DES PRODUKTES
Wie durch das Symbol seitlich angegeben, ist es
verboten, dieses Produkt zum Haushaltmüll zu
geben.
ES - ELIMINACIÓN DEL PRODUCTO
Tal como indicado por el símbolo de aquí al lado,
está prohibido arrojar este producto a los residuos
urbanos.
PL - UTYLIZACJA PRODUKTU
Zgodnie ze wskazaniem symbolu na rysunku obok
zabronione jest wyrzucanie tego produktu razem z
odpadami domowymi.
EN - Installation instructions and warnings
IT - Istruzioni ed avvertenze per l’installazione
FR - Instructions et recommandations pour l’installation
ES - Instrucciones y advertencias para la instalación
DE - Anleitung und Hinweise zur Installation
PL - Instrukcje i zalecenia dotyczące montażu
FLOX1
FLOX2
FLOXB2
FLOXI
FLOXI2
FLOXM
FLOXM220
2
25 mm
98 mm
41 mm
CB
101
12
54632
-
OUT1
OUT2
1
+
A
12-24 V ac/dc
18 ÷ 28
V
10 ÷ 18 V
MXD
MXT
NC
B
A
NC
NA
A
NA
B
T2
T1
B
A
B
A
B
A
B
A
F
F
H
G
E
F
H
G
E
F
H
G
E
H
G
E
F
E
H
G
H
G
E
F
= T
= S
FLO2FLO1
H
E
G
F
B
A
T
2 - OUT2
T
1 - OUT3
T
2 - OUT4
T1 - OUT3
T
2 - OUT3
T
1 - OUT1
T
1 - OUT3
T
1 - OUT4
T1 - OUT2
T
1 - OUT1
T
2 - OUT2
T
1 - OUT4
T2 - OUT4
T1 - OUT1
T2 - OUT2
T
1 - OUT1
NA
BA
RL 2
NC
NA
NC
A B
NA
RL 1
NA
NC
NC
LS
111
-A
OFF
ON
101
T4 - OUT1T3 - OUT1T2 - OUT1T1 - OUT1
T3 - OUT2 T4 - OUT2T3 - OUT1 T4 - OUT1
T1 - OUT2 T2 - OUT2T1 - OUT1 T2 - OUT1
FLOXM220: 230 Vac
21
12
A
10 ÷ 18 V
18 ÷ 28
V
109875643
MXT
MXD
M
FLOXM: 12-24 Vac/dc
MXP
110
B
T4
T3
T2
OUT1
OUT2
OUT3
OUT4
T1
21
-+
L
T2 (OFF)
T1 (ON)
VERY VEFLO1
L
T1
T2
T4
T3
FLO4FLO2
105 mm
34 mm
68 mm
147 mm
108 mm
52 mm 118 mm
11a
11b
14
13
12
8 9
5 6
1 2 3 4
10 7
3
GB
Product description
Version Power input Connections Format Outputs Fixing Version Power input Buttons
FLOX1 12/24 V ac/dc Term. board Universal (fig.1) 1 Adhesive or screws FLO1 12V alkaline battery 1
FLOX2 12/24 V ac/dc Term. board Universal (fig.1) 2 Adhesive or screws FLO2 12V alkaline battery 2
FLOXB2 12/24 V ac/dc Term. board Box (IP53) (fig.2-3) 2 Adhesive or screws FLO4 12V alkaline battery 4
FLOXI 24 V ac/dc Nice slot Slot 1 Slot on Nice control unit VERY VE 2 3V lithium batteries 2
FLOXI2 24 V ac/dc Nice slot Slot 2 Slot on Nice control unit
FLOXM 12/24 V ac/dc Term. board Modular (fig.4) Up to 4 Screws
FLOXM220 230 Vac Term. board Modular (fig.4) Up to 4 Screws
The available receivers are: tab.1 The available transmitters are: tab.2
T1 T2 T1 T2
T1 T2
= ON = OFF
TX1°TX TX
2° .... 10°
x5
The FLO series radio control device is a radio system working at a frequency of 433.92 Mhz which remote controls door opening devices, gate opening devices and similar
pieces of equipment.
The system works by transmitting and receiving a digital code featuring 1024 combinations for each transmitter button.
Installation: Receivers
The FLOX1, FLOX2, FLOXB2 and FLOXM receivers can be powered by 24V ac/dc or 12V ac/dc. The power input mode can be selected by means of a jumper with tab
(ref. A fig.5 and 6).
Make sure the power input mode is correct before powering the receiver.
In all the versions, the receiver outputs are normally open (N.O.) pure contacts provided by the relays on the board. In the FLOXM and FLOXM220 versions, the outputs
are provided through the plug-in relay units (ref. M fig.6); there are three kinds of relay unit:
MXD: this output is impulsive, that is, it remains active as long as the command signal remains.
MXP: this output is step-by-step, that is, each command signal switches the status of the relay contact.
MXT: this output is timed, that is, after being activated it remains so for a period of time that can be adjusted from 3 seconds to about 5 minutes (use a maximum of 2 MXT units).
If a normally closed “NC” type of contact is needed, for versions FLOX1, FLOX2, FLOXB2, FLOXI and FLOXI2 proceed as follows
1. Disconnect the receiver (FLOX1, FLOX2, FLOXB2) if powered or remove the board from the slot (FLOXI and FLOXI2).
2. Open the receiver box and remove the board with care (FLOX1, FLOX2, FLOXB2).
3. On the solder side of the receiver: cut the copper section at point A and then connect the bump contacts with a spot of solder in point B (fig.9)
In the FLOXM and FLOXM220 versions, proceed as described in points 2 and 3 on the solder side of the relay units (fig.8).
If more than one receiver is installed close to each other, make sure they are over 50 cm apart in order to prevent interference.
Associating transmitter buttons with r
eceiver output: The FLOXM and FLOXM220 receivers feature 4 slots for the relay units, each one of which corresponds to a button
on the transmitter (fig.6). For the FLOX1, FLOXI, FLOX2, FLOXI2 and FLOXB2 receivers, each output relay is associated with a certain button by inserting a selection jumper
(ref. C fig.5): for the FLOX1 and FLOXI receivers, refer to figure 11a; for the FLOX2, FLOXI2 and FLOXB2 receivers, refer to figure 11b.
Entering the code: set the 10 dip switches (ref. B fig.5 and 6) to ON – OFF in order to create the required combination.
Installation: Aerial
To guarantee optimum performance, each FLO receiver must be installed with its own ABF or ABFKIT aerial. The aerial must be installed as high as possible; if there are
metal structures or reinforced concrete walls nearby, install the aerial on top of them. If the cable supplied with the aerial is too short, use a coaxial cable with an impedance
of 52 ohms (e.g.: RG58 with low dispersion); the total length of the cable must not exceed 10 m. Connect the aerial to the relative terminal (fig.5 and 6) by connecting the
central part (core) to terminal 2 and the braid to terminal 1.
If the aerial must be installed where there is not a good earth level (e.g.: masonry structures), terminal 1 of the aerial can be earthed to obtain a wider range of action; this
is clearly advantageous if the quality of the earth connection is good and it is located in the immediate vicinity. Good results can be obtained, however, by using an 18 cm
long piece of wire, mounted horizontally and connected to terminal 2 of the aerial input, as an aerial.
Installation: Transmitters
Entering the code for the FLO series: Open the transmitter (fig.13) and move the 10 dip switches in order to obtain the same combination as the receiver.
Entering the code for the VERY VE series: Enter the code with the two transmitter buttons as follows:
1. Press down both buttons on the transmitter until the LED lights up (ref. L fig.7), then start entering the code sequence within
5 seconds.
2. Press button T1 if dip switch 1 on the receiver is ON, otherwise button T2 if this dip switch is OFF (fig.7).
3. Repeat point 2 for all the 10 dip switches of the receiver. The example shown in fig. 10 is obtained with the sequence
T1-T1-T2-T1-T1-T1-T2-T2-T2-T1.
4. After the 10th dip switch is entered the LED will start flashing rapidly for 5 seconds. If no button is pressed while the LED flashes,
the code will be memorised, otherwise the operation will be cancelled.
If there is more than one VERY VE’s to programme, it may be easier to use the relative CVU programming unit; this can even set up two different codes for the two buttons.
Selecting the transmitter buttons. If necessary, the “value” of the buttons in the transmitters can be modified, that is, for example, by pressing button T1 to transmit the
button T2 code. For transmitters FLO1 and FLO2 this can be done by cutting point “T” and applying a spot of solder at point “S”, as shown in fig. 12. The FLO4 transmitter
cannot be modified. With the VERY VE transmitters selection can only be made by using the relative CVU programming unit.
Maintenance
The receiver is maintenance-free. In the transmitters, instead, if there is a considerable loss of range or if the LED on the VERY VE (ref. L fig.7) transmitters lights up
discontinuously, replace the battery. To do this, open the transmitter as shown in figs. 13, 14.
Disposal
This product is made from various kinds of material, some of which can be recycled while others must be disposed of. Find out about recycling or disposal systems in
compliance with current by-laws.
Some electronic components may contain polluting substances: do not dump them.
Technical features
Nice S.p.A. reserves the right to modify the products whenever it sees fit and without notice.
!!!
Receivers
Reception frequency : 433.92 MHz
Power input : 24V or 12V ac/dc ± 10%
230 Vac ± 10% for FLOXM220
Sensitivity : < 0.5µV (range 100-150m
with ABF- ABFKIT aerial)
Stand-by/active channel consumption : 15 mA / 35 mA
Decoding : digital ( 1024 combinations)
N° outputs : from 1 to 4 depending on the versions
Relay contact : max. 0.5A 48V ac/dc.
Excite / de-excite time : 250mS / 300 mS
Operating temperature : -10°C +55°C
Transmitters
Transmission frequency : 433.92 MHz
Irradiated power : 100 µW
Carrier frequency tolerance : ± 100 KHz
Coding : digital (1024 combinations)
N° buttons : 1, 2 or 4 depending on version
Operating temperature : -10°C + 55°C
Dimensions / weight FLO series : 69 x 39 x 15.5 / 31g
Dimensions / weight VERY VE : 65 x 30 x 10 / 14g
Loading...