NETGEAR 108 Mpbs
Wireless USB 2.0 Adapter
WG111T User Manual
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
202-10056-03
February 2007
Page 2
Technical Support
Please refer to the support information card that shipped with your product. By registering your
product at http://www.netgear.com/register, we can provide you with faster expert technical
support and timely notices of product and software upgrades.
NETGEAR, INC. Support Information
Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support
information card.
E-mail: support@netgear.com
Web site: http://www.netgear.com
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications
Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic,
building materials and construction, and network overhead, lower actual data throughput rate.
Safety and Regulatory Notices
FCC Statement
The WG111T has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the
FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
These limits are designed to prov ide rea sonabl e pr otecti on against harmful interference in a residential inst allat ion. T his
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to rad io or television
reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•Reorient or relocate the receiving antenna
ii
v2.0, February 2007
Page 3
•Increase the separation between the equipment or devices
•Connect the equipment to an outlet other than the receiver’s
•Consult a dealer or an experienced radio/TV technician for assistance
FCC Caution: Any change or modification to the product not expressly approved by Netgear could void the user’s
authority to operate the device.
FCC RF Radiation Exposure and SAR Statements
SAR Statement
The Netgear WG111T has been tested for body-worn Specific Absorption Rate (SAR) compliance.
The FCC has established detailed SAR requirements and has established that these requirements
have been met while installed in host notebook computer.
RF Exposure Information
The radio module has been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the
requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency
devices. This model meets the applicable government requirements for exposure to radio frequency waves. The highest
SAR level measured for this device was 0.74 W/kg.
Canadian Department of Communications Industry Canada (IC) Notice
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Cet ap pareil numérique de la classe B
est conforme à la norme NMB-003 et CNR-210 du Canada.
“To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to
licensing.”
“Pour empêcher que cet appareil cause du brouillage au service faisant l’objet d’une licence, il doit être utilisé à
l’intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son
antenne d’émission) est installé à l’extérieur, il doit faire l’objet d’une licence.”
Europe - EU Declaration of Conformity
A printed copy of the EU Declaration of Conformity certificate for this product is provided in the WG111T product
package.
Èesky
[Czech]
Dansk
[Danish]
Deutsch
[German]
NETGEAR, Inc. tímto prohlašuje, že tento NETGEAR 108 Mbps Wireless USB 2.0
Adapter WG111T
ustanoveními smìrnice 1999/5/ES.
Undertegnede NETGEAR, Inc. erklærer herved, at følgende udstyr NETGEAR 108 Mbps
Wireless USB 2. 0 Ad apter WG111T
krav i direktiv 1999/5/EF.
Hiermit erklärt NETGEAR, Inc., dass sich das Gerät NETGEAR 108 Mbps Wireless USB
2.0 Adapter WG11 1T in Übereinstimmung mit den grundlegenden Anforderungen und den
übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
je ve shodì se základními požadavky a dalšími pøíslušnými
overholder de væsentlige krav og øvrige relevante
iii
v2.0, February 2007
Page 4
Eesti
[Estonian]
EnglishHereby, NETGEAR, Inc., declares that this NETGEAR 108 Mbps Wireless USB 2.0
Käesolevaga kinnitab NETGEAR, Inc. seadme NETGEAR 108 Mbps Wireless USB 2.0
Adapter WG111T
tulenevatele teistele asjakohastele sätetele.
Adapter WG111T
provisions of Directive 1999/5/EC.
vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
is in compliance with the essential requirements and other relevant
Español
[Spanish]
Ελληνική
[Greek]
Français
[French]
Italiano
[Italian]
Latviski
[Latvian]
Lietuviø
[Lithuanian]
Nederlands
[Dutch]
Malti
[Maltese]
Por medio de la presente NETGEAR, Inc. declara que el NETGEAR 108 Mbps Wireless
USB 2.0 Adapter WG111T
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
ΜΕΤΗΝΠΑΡΟΥΣΑ NETGEAR, Inc. ΔΗΛΩΝΕΙΟΤΙ NETGEAR 108 Mbps Wireless
USB 2.0 Adapter WG111T
ΚΑΙΤΙΣΛΟΙΠΕΣΣΧΕΤΙΚΕΣΔΙΑΤΑΞΕΙΣΤΗΣΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Par la présente NETGEAR, Inc. déclare que l'appareil NETGEAR 108 Mbps Wireless
USB 2.0 Adapter WG111T
dispositions pertinentes de la directive 1999/5/CE.
Con la presente NETGEAR, Inc. dichiara che questo NETGEAR 108 Mbps Wireless
USB 2.0 Adapter WG111T
pertinenti stabilite dalla direttiva 1999/5/CE.
Ar šo NETGEAR, Inc. deklarç, ka NETGEAR 108 Mbps Wireless USB 2.0 Adapter
WG111T
noteikumiem.
Šiuo NETGEAR, Inc. deklaruoja, kad šis NETGEAR 108 Mbps Wireless USB 2.0
Adapter WG111T
Hierbij verklaart NETGEAR, Inc. dat het toestel NETGEAR 108 Mbps Wireless USB 2.0
Adapter WG111T
bepalingen van richtlijn 1999/5/EG.
Hawnhekk, NETGEAR, Inc., jiddikjara li dan NETGEAR 108 Mbps Wireless USB 2.0
Adapter WG111T
hemm fid-Dirrettiva 1999/5/EC.
atbilst Direktîvas 1999/5/EK bûtiskajâm prasîbâm un citiem ar to saistîtajiem
atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
in overeenstemming is met de essentiële eisen en de andere relevante
jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li
cumple con los requisitos esenciales y cualesquiera otras
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣΤΙΣΟΥΣΙΩΔΕΙΣΑΠΑΙΤΗΣΕΙΣ
est conforme aux exigences essentielles et aux autres
è conforme ai requisiti essenziali ed alle altre disposizioni
Magyar
[Hungarian]
Polski [Polish] Niniejszym
Alulírott,
Adapter WG111T
irányelv egyéb elõírásainak.
NETGEAR, Inc. nyilatkozom, hogy a NETGEAR 108 Mbps Wireless USB 2.0
NETGEAR, Inc. oœwiadcza, ¿e NETGEAR 108 Mbps Wireless USB 2.0
Adapter WG111T
postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese]
Slovensko
[Slovenian]
NETGEAR, Inc. declara que este NETGEAR 108 Mbps Wireless USB 2.0 Adapter
WG111T está conforme com os requisitos essenciais e outras disposições da Directiva
1999/5/CE.
NETGEAR, Inc. izjavlja, da je ta NETGEAR 108 Mbps Wireless USB 2.0 Adapter
WG111T
ES.
v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloèili direktive 1999/5/
iv
megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC
jest zgodny z zasadniczymi wymogami oraz pozosta³ymi stosownymi
v2.0, February 2007
Page 5
Slovensky
[Slovak]
NETGEAR, Inc. týmto vyhlasuje, že NETGEAR 108 Mbps Wireless USB 2.0 Adapter
WG111T
spåòa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish]
Svenska
[Swedish]
NETGEAR, Inc. vakuuttaa täten että NETGEAR 108 Mbps Wireless USB 2.0 Adapter
WG111T
direktiivin muiden ehtojen mukainen.
Härmed intygar NETGEAR, Inc. att denna [utrustningstyp] står I överensstämmelse med
de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien
Product and Publication Details
Model Number:WG111T
Publication Date:February 2007
Product Family:Wirless Adapter
Product Name:NETGEAR 108 Mbps Wireless USB 2.0 Adapter WG111T
Home or Business Product:Home
Language:English
Publication Part Number:202-10056-03
v
v2.0, February 2007
Page 6
vi
v2.0, February 2007
Page 7
Contents
About This Manual
Conventions, Formats, and Scope ..................................................................................... i
How to Use This Manual ................................................................................................... ii
How to Print this Manual .................................................................................................... ii
Chapter 1
Basic Setup
What You Need Before You Begin ..................................................................................1-1
Verify System Requirements ....................................................................................1-1
Observe Wireless Location and Range Guidelines ..................................................1-2
What Is in the Box ..........................................................................................................1-3
Ad Hoc Mode Is Not Working Correctly ..........................................................................3-3
Windows XP Occasional Connection Problems .............................................................3-3
Appendix A
Technical Specifications
Appendix B
Related Documents
viii
v2.0, February 2007
Page 9
About This Manual
The NETGEAR® 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual describes how to
install, configure and troubleshoot the NETGEAR 108 Mbps Wireless USB 2.0 Adapter WG11 1T.
The information in this manual is intended for readers with intermediate computer and Internet
skills.
Conventions, Formats, and Scope
The conventions, formats, and scope of this manual are described in the following paragraphs:
•Typographical Conventions. This manual uses the following typographical conventions:
ItalicsEmphasis, books, CDs, URL names
BoldUser input
•Formats. This manual uses the following formats to highlight special messages:
Note: This format is used to highlight information of importance or special interest.
Tip: This format is used to highlight a procedure that will save time or resources.
•Scope. This manual is written for the WG1 11 108 Mbps Wireless USB 2.0 Adapter according
User Manual for the NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T
For more information about network, Internet, firewall, and VPN technologies, see the links to the
NETGEAR website in Appendix B, “Related Documents”.
Note: Product updates are available on the NETGEAR, Inc. website at
http://kbserver.netgear.com/products/WG111T.asp.
How to Use This Manual
The HTML version of this manual includes the following:
•Buttons, and , for browsing forwards or backwards through the manual one page
at a time
•A button that displays the table of contents and an button. Double-click on a
link in the table of contents or index to navigate directly to where the topic is described in the
manual.
•A button to access the full NETGEAR, Inc. online knowledge base for the product
model.
•Links to PDF versions of the full manual and individual chapters.
How to Print this Manual
To print this manual you can choose one of the following several options, according to your needs.
•Printing a Page in the HTML View.
Each page in the HTML version of the manual is dedicated to a major topic. Use the Print
button on the browser toolbar to print the page contents.
•Printing a Chapter.
Use the PDF of This Chapter link at the top left of any page.
–Click the PDF of This Chapter link at the top left of any page in the chapter you want to
print. The PDF version of the chapter you were viewing opens in a browser window.
–Your computer must have the free Adobe Acrobat reader installed in order to view and
print PDF files. The Acrobat reader is available on the Adobe we b site at
http://www.adobe.com.
x
v2.0, February 2007
Page 11
User Manual for the NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T
–Click the print icon in the upper left of the window.
Tip: If your printer supports printing two pages on a single sheet of paper, you can
save paper and printer ink by selecting this feature.
•Printing the Full Manual.
Use the Complete PDF Manual link at the top left of any page.
–Click the Complete PDF Manual link at the top left of any page in the manual. The PDF
version of the complete manual opens in a browser window.
–Click the print icon in the upper left of the window.
Tip: If your printer supports printing two pages on a single sheet of paper, you can
save paper and printer ink by selecting this feature.
xi
v2.0, February 2007
Page 12
User Manual for the NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T
xii
v2.0, February 2007
Page 13
Chapter 1
Basic Setup
The NETGEAR 108 Mbps Wireless USB 2.0 Adapter WG111T lets you connect a PC computer to
wireless networks. It is designed for PC computers running Microsoft Windows. For information
about product features and compatible NETGEAR products, see the NETGEAR website at
http://www.netgear.com.
This chapter describes how to install your WG111 108 Mbps Wireless USB 2.0 Adapter and set up
basic wireless connectivity on your Wireless Local Area Network (WLAN). Advanced wireless
network settings are covered in Chapter 2, “Network Connections and Wireless Security”
Note: Indoors, computers can connect to 802.11 wireless networks at distances of several
hundred feet. Because walls do not always block wireless signals, others outside
your immediate area could access your network. It is important to take steps to
secure your network from unauthorized access. The WG111 108 Mbps Wireless
USB 2.0 Adapter provides highly effective security features, which are covered in
Chapter 2, “Network Connections and Wireless Security”. Deploy the security
features appropriate to your needs.
What You Need Before You Begin
You must verify that your computer meets the minimum system requirements and identify the
wireless network settings of the wireless network where you will connect before you can set up
your wireless USB adapter and connect.
Verify System Requirements
Before installing the WG11 1 108 Mbps Wireless USB 2.0 Adapter, make sure that these minimum
requirements have been met. You must have a computer with:
®
•A Pentium
300 MHz or higher compatible processor with an available USB 2.0 or 1.1 port.
Note: If you do not have a USB 2.0 port on your PC, the throughput of the WG111T
will be limited to the 14 Mbps of the USB 1.1 standard.
1-1
v2.0, February 2007
Page 14
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
•A CD drive.
•5 Mbytes of free hard disk space.
•Windows Vista, XP Home, XP Professional, or 2000. Some versions of Windows may ask fo r
the original Windows operating system installation files to complete the installation of the
WG111T driver software.
Note: Windows XP users must install SP2 or install the KB822603 Hot fix which fixes
the USB 2.0 Host controller driver.
Observe Wireless Location and Range Guidelines
Computers can connect over wireless networks indoors at a range which vary significantly based
on the physical location of the computer with the NETGEAR 108 Mbps W ireless USB 2.0 Adapter
WG111T. For best results, avoid potential sources of interference, such as:
•Large metal surfaces
•Microwaves
•2.4 GHz Cordless phones
In general, wireless devices can communicate through walls. However, if the walls are constructed
with concrete, or have metal, or metal mesh, the effective range will decrease if such materials are
between the devices.
1-2
v2.0, February 2007
Page 15
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
What Is in the Box
The product package should contain the following items:
•NETGEAR 108 Mbps Wireless USB 2.0 Adapter WG111T
•Installation Guide for the NETGEAR 108 Mbps Wireless USB 2.0 Adapter WG111T
•NETGEAR CD, including:
–Driver and Configuration Utility Software
–NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual (this document)
–Animated Network Properties Configuration Tutorial
–PC Networking Tutorial
•Warranty and Support information card
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product for repair.
WG111T Default Wireless Settings
If this is a new wireless network installation, use the factory default settings to set up the network
and verify wireless connectivity. If this is an addition to an existing wireless network, you will
need to identify the wireless network and wireless security settings that are already defined.
Your NETGEAR 108 Mbps Wireless USB 2.0 Adapter WG11 1T factory default basic settings are:
•Network Name Service Set Identification (SSID): Any (First available network)
Note: In order for the WG111 108 Mbps Wireless USB 2.0 Adapter to communicate
with a wireless access point or wireless adapter, all devices must be set up to
use the same wireless network name (SSID).
•Network Mode (Infrastructure or Ad-hoc): Infrastructure
•Data security WEP, WPA2-PSK, or WPA-PSK encryption: Disabled
The section below provides instructions for setting up the NETGEAR 108 Mbps Wireless USB 2.0
Adapter WG11 1T for basic wireless connectivity to an access point. The procedures below provide
step-by-step installation instructions for Windows PCs. Use the procedure that corresponds to the
version of Windows that you are using.
1-3
v2.0, February 2007
Page 16
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Installation
The instructions in this chapter explain how to install the WG111 T to connect to a network with an
access point or router. Wireless security, advanced settings, and Computer-to-Computer (Ad Hoc)
instructions are covered in Chapter 2, “Network Connections and Wireless Security”.
Follow the instructions below to install the WG111 108 Mbps Wireless USB 2.0 Adapter:
1.First, install the WG111T software:
Insert the NETGEAR CD. If the CD main page does not appear, double click Autorun.exe on
the CD.
a.Click Install the Software.The Check for Updates window will open.
Figure 1-1
b.If you are connected to the Internet, click Check for Updates. If not, you can choose to
install from the CD.
c.When the Installation Complete message appears, click Next.
d.On the Smart Wizard screen, click Next to proceed with the Smart Wizard setup.
1-4
v2.0, February 2007
Page 17
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
2.Now, connect the wireless USB adapter.
Figure 1-2
a.Locate an available USB port on your PC. Connect the USB cable to the WG111T and
insert the other end of the cable into the USB slot on your PC. See “Placing the USB
Adapter Cradle” on page 1-10.
b.Restart your computer.
You will be prompted to select the country where you are located.
c.Select the country and click Agree.
3.Use the Smart Wizard to set up your wireless USB adapter.
a.Windows 2000 users go to Step b. Windows XP or Vista users can set up the wireless
adapter with the NETGEAR Smart Wizard (recommended) or the Windows configuration
utilities.
•NETGEAR Smart Wizard: Reveals more information about each network and
makes it easier to troubleshoot network connection problems.
•Windows configuration utilities: See the Windows documentation or “Using
Windows XP and Vista Wireless Configuration Utilities” at:
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
You will be prompted to let the wizard help you connect to a network (recommended).
Figure 1-3
c.Click Next to accept.
4.Connect to a wireless network.
a.Select the wireless network from the drop-down list, and the wizard records your choice.
Hidden
Figure 1-4
Note: Hidden networks do not broadcast the Network Name (SSID ) . These
networks are in the drop-down list, but the Network Name (SSID) is blank.
b.If the network uses security, then the Smart Wizard detects it
c.Follow the Wizard steps for Security (if used) and for saving a Profile.
1-6
v2.0, February 2007
Page 19
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
d.After you have reviewed the settings, click Finish.
The WG11 1T icon appears in the system tray and on the desktop. The wizard initiates
your wireless connection. It could take up to a minute for your wireless connection to be
established.
The Smart Wizard Settings page opens.
Figure 1-5
5.Use the status bar to verify your wireless connectivity. For more details about connecting, see
“Connecting to Wireless Networks and the Internet” on page 1-7.
Connecting to Wireless Networks and the Internet
Note: The maximum speed of a USB v2.0 port is 480 Mbps. If your computer has a USB
v1.1 port, the WG111 T is limited to that port’s maximum speed, which is 14 Mbps.
The WG11 1T has indicators in three locations that show the status of your connection to a wireless
network and to the Internet:
•WG111T Icon: After you install the WG111T software, the icon appears on the desktop
and in the lower right of the Windows task bar. It is color coded to show the status of the
connection.
1-7
v2.0, February 2007
Page 20
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
•Smart Wizard Status Bar: Clicking on the system tray icon opens the Smart Wizard. The
status bar at the bottom of the page shows details about your wireless and Internet connection.
See “Smart Wizard Status Bar” on page 1-9.
•WG111 108 Mbps Wireless USB 2.0 Adapter LED: The LED on the wireless USB adapter
shows the network connection. Solid indicates a connection. The LED blinks when the
wireless USB adapter is looking for a network association.
WG111T Icon Colors
The WG11 1T icon is on the desktop and in the W indows System T ray (SysT ray). The System T ray
resides on one end of the taskbar in the Microsoft Windows desktop.
ColorConditionDescription
RedThe wireless USB adapter
has no connection to any
other wireless node.
YellowThe wireless USB adapter
has a connection with another
wireless node.
GreenThe wireless USB adapter
has a connection with another
wireless node.
The wireless USB adapter is not able to link to any other
wireless node or the link is lost. Check your configuration or
try moving to a location where the wireless signal quality is
better.
The wireless link is weak. You may need to move to a better
spot, such as closer to the wireless access point. Also, look
for possible interference such as a 2.4 GHz cordless phone or
large metal surface.
The wireless USB adapter has established good
communication with an access point and the signal quality is
strong.
1-8
v2.0, February 2007
Page 21
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Smart Wizard Status Bar
Click the icon to open the Smart Wizard so you can view the status bar. The Smart Wizard
Settings page opens. The status bar is located at the bottom of the Settings page.
Security
Wireless
network
Find a Network
Channel
Throughput
Signal
strength
Connection status
Figure 1-6
The following table describes how to interpret the Smart Wizard status bar
Understanding the Status Bar
Wireless networkIdentifies which wireless network you have joined.
Security• Locked: security enabled.
• Unlocked: security not enabled.
ChannelThe wireless channel used by the network. If many wireless networks in your
area use the same channel they can interfere with one another.
ThroughputWireless throughput measured in Mega bits per second.
If your computer has a USB v1.1 port, the WG111T is limited to that port’s
maximum speed, which is 14 Mbps.
Signal strengthMore dots indicates a stronger signal. Usually, you will experience higher
throughput when the signal is strongest.
Find a NetworkClick Find a Network to open the Connection Wizard.
Connection
status
Identifies the status of your network connection.
• Connected to Internet: Wireless Internet connection is OK.
• Connected to Router: Wireless connection to the router is OK but the router
is not connected to the Internet.
• 169.254.x.x or ___.___.___.___ : The wireless connection to the router is OK
but there is a problem with the router. See Chapter 3, “Troubleshooting”.
1-9
v2.0, February 2007
Page 22
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
If you right-click in the system tray icon, you can disable the Internet notification feature by
clearing check mark on this line. If you do so, then only the IP address is shown.
Figure 1-7
WG111T LED
The LED on the wireless USB adapter indicates the condition of wireless link.
LED Meaning
Off • The WG111T in not plugged in to the PC.
• Power save mode (default from power up or reset).
BlinkLooking for network association.
OnAssociated or joined with network.
Placing the USB Adapter Cradle
You can attach the WG111 108 Mbps Wireless USB 2.0 Adapter directly to a USB port on your
computer, or use the USB cable to extend the range and obtain better wireless reception.
Follow these instructions to use the USB cable, plastic cradle, and loop and hook fastener provided
in the package for better USB Adapter placement on a notebook computer:
1.The WG111 108 Mbps Wireless USB 2.0 Adapter comes with three black fasteners. Locate
the one that has a prickly side and attach it to the plastic cradle on the middle of the outside
rear.
2.Insert the WG111 108 Mbps Wireless USB 2.0 Adapter in the plastic cradle.
Figure 1-8
1-10
v2.0, February 2007
Page 23
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
3.Place one of the other pieces of loop and hook fastener on the back of your monitor near the
top for better reception.
Figure 1-9
Note: The last piece of the fastener can be placed on the side of your PC monitor
nearest your wireless access point, if you are using the USB Adapter with a
desktop PC.
4.Join the pieces of the fastener to attach the USB Adapter in the plastic cradle to the notebook
or desktop monitor.
See the installation instructions for your operating system before attaching the USB cable to the
USB Adapter and your computer.
Removing the WG111T Software
You can remove the wireless adapter software in these two ways:
•Navigate the Windows Start menu to the WG111 108 Mbps Wireless USB 2.0 Adapter
program group, select the uninstall option, and follow the screen prompts.
•Navigate the Windows Start menu to the Control Panel Add or Remove Program item, select
the WG111 108 Mbps Wireless USB 2.0 Adapter option, and follow the screen prompts.
1-11
v2.0, February 2007
Page 24
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Upgrading the WG111T Software
Upgrades may be available at the NETGEAR website. To install an upgrade, follow these steps.
1.Write down the settings for any profiles that you want to save. They will not be retained.
2.Download the upgrade from the NETGEAR website Support page.
3.Remove the WG111T software from your laptop computer.
4.Remove the WG111T adapter from your laptop computer, and if prompted restart your
computer.
5.Run the installer that you downloaded (the file ends in .exe).
6.Follow the installer instructions, and if prompted, then restart your laptop computer.
1-12
v2.0, February 2007
Page 25
Chapter 2
Network Connections and Wireless Security
This chapter explains how to use your Wireless USB 2.0 Adapter to connect to your Wireless
Local Area Network (WLAN) and how to set up wireless security for the Wireless USB 2.0
Adapter so that it matches the wireless security settings for your network.
If you chose the Windows XP or W indows Vista Zero Configuration utility during installation, and
now you want to use the Smart Wizard, then you need to disable the Windows utility. If you are
working with the Vista configuration utility, see the online document:
To disable the Windows Zero Configuration utility:
1.Attach the wireless adapter to a USB port for your computer.
2.Go to Windows Start menu and select Network Connections.
3.On the Network connections page, select the Wireless Network Connection and right-click to
choose the Properties option.
Figure 2-1
2-1
v2.0, February 2007
Page 26
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
4.Click the Wireless Networks tab. Then clear the “Use Windows to configure my wireless
settings” check box.
Understanding the Smart Wizard
These instructions explain how to use the NETGEAR WG111T Smart Wizard to change the
WG111 108 Mbps Wireless USB 2.0 Adapter wireless settings.
When you have installed the software from the NETGEAR CD, the icon appears on your
desktop and in the Windows System Tray. The Windows System Tray is located on the Windows
taskbar. You can either double-click this icon on the desktop, or click it in the System Tray at any
time, to use the Smart Wizard. This software automatically restarts when you reboot your
computer.
The Smart Wizard provides a complete and easy to use set of tools to:
•View details about wireless networks in your area.
•Choose the network that you want to use.
•Configure wireless settings for your wireless USB adapter
•Save your wireless network settings in profiles.
•Remove or reinstall the wireless adapter software.
The following sections in this chapter explain how to use the Smart Wizard.
Viewing Wireless Networks in Your Area
You can use the Networks tab to view all available wireless networks in your area. You can also
scan to search for wireless networks and refresh the page.
To view information about wireless networks:
1.Use the icon to open the Smart Wizard. The Settings tab page opens.
2.Click the Networks tab to view the following page:
2-2
v2.0, February 2007
Page 27
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
You can click a column
heading to sort.
If many networks use
the same channel they
can interfere with each
other.
The Status bar shows
your network connection
and Internet connection.
Figure 2-2
The screen shows the following information for each network scanned:
•Network Name (SSID): The name assigned to a wireless network. This is the same as the
SSID or ESSID configuration parameter. Note that as a security measure, some wireless
access points do not broadcast their SSID. In such cases, the SSID field will be blank even
though the rest of the information will still be displayed.
•Channel: The channel determines which operating frequency will be used.
•Security: Identifies whether the wireless network uses security settings such as WEP,
WPA2-PSK, or WPA-PSK.
•Signal: Identifies the signal strength of the communications.
•MAC Address: Identifies the hardware address (MAC Address) of the wireless device
broadcasting this information.
•Mode: Identifies the type of wireless network—Access Point (Infrastructure) or Computer-toComputer (Ad Hoc)
The buttons located at the bottom of the Networks tab are:
•Help: Display online help.
•Find a Network: Find and connect to a network. See “Finding a Network” on page 2-4.
•Connect: Connect to the network that you selected.
•Scan: Check for wireless networks. Clicking Scan refreshes the page.
•Close: Close the window of the Wizard.
2-3
v2.0, February 2007
Page 28
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Finding a Network
During the WG111T software installation, the Smart Wizard lists the available networks. After
installation you can use the Find a Network button on the Network tab at any time to view the
available networks and select the one that you want to use.
Note: Make sure that you know the security settings for the network that you want to use.
For example, if WEP is used then you need to know the WEP key. If you use
secure networks frequently, set up profiles for each network with the wireless
network and security settings.
Follow the steps below to Find a Network:
1.Use the icon to open the Smart Wizard.
The Settings tab page opens.
2.On the Networks tab page, click Find a Network.
Figure 2-3
2-4
Hidden Network
v2.0, February 2007
Page 29
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
3.Select a network from the drop down list. If you select a hidden network then you must enter
the SSID. Click Next.
4.Follow the steps of the wizard to specify the wireless security if used, and to create a profile.
5.Review you settings, and click Finish.
The Smart Wizard initiates your wireless connection. You can use the Status Bar to verify your
network connection. For more information, see “Smart Wizard Status Bar” in Chapter 1.
Profiles
The WG111T Smart Wizard uses profiles to store all the settings for a particular wireless network.
There are two special profile names: Default and Profile.
•Default: The Profile named Default automatically scans for any available network. You
cannot change this profile name.
•Profile: If you do not enter a name in the Profile Name box, then the name Profile is used to
save your settings. If you do this more than once then you will be asked if you want to replace
the previous settings stored in Profile.
Adding Profiles
You can store multiple profiles and recall the one which matches the network you want to join.
If you use your computer to connect to different wireless networks, you can create a profile for
each wireless network. Then, you can easily load the profile that has all the settings that you need
to join the network you are using at the time.
There are two types of wireless network profiles that you can set up:
•Access Point (Infrastructure) – Connect to an access point or router with the 802.11
infrastructure mode.
•Computer-to-Computer (Ad Hoc) – Connect directly to another computer with the 802.11
ad hoc mode.
For more information, see the wireless reference document at:
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Setting up a Profile to Connect to an Access Point or Router
Follow these instructions to set up the WG111 108 Mbps Wireless USB 2.0 Adapter to connect to
a wireless access point or router.
1.Use the icon to open the Smart Wizard. The Settings page opens.
Figure 2-4
2.Enter the network settings.
a.In the Network Type section, be sure that Access Point (Infrastructure) is selected.
b.In the Profile box, type the name of the profile.
c.In the Network Name (SSID) field select a network or enter the SSID.
Note: You will not get a wireless network connection unless the network SSID
matches exactly the SSID used by the access point.
3.Save your settings in a Profile.
a.Click the Save Profile button.
All the configuration settings are saved in this profile.
b.Click Apply and then click Close to exit the wizard, or Cancel to return to the previous
settings.
2-6
v2.0, February 2007
Page 31
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
4.Verify wireless connectivity to your network.
Use a browser to connect to the Internet, or check for file and printer access on your network.
You can check the status bar in the Smart Wizard for the current connection status.
Note: If you cannot connect, see Chapter 3, “Troubleshooting”. For problems with
accessing network resources, the Windows Client and File and Print Sharing
software might not be installed and configured properly on your computers. Please
refer to “Internet Networking and TCP/IP Addressing” in Appendix B.
Setting up a Computer-to-Computer (Ad Hoc) Profile
The Computer-to-Computer setting uses Ad Hoc mode. Ad Hoc mode is an 802.11 networking
framework in which devices or computers communicate directly with each other, without the use
of an access point. For example, this mode is used when two Windows computers are configured
with file and print sharing enabled and you want to exchange files directly between them.
Note: Ad Hoc mode will not work using DHCP settings. Ad Hoc mode requires either
static IP addresses (such as
192.168.0.1) or the IPX protocol. For instructions on
setting up static IP addresses on a Windows PC, refer to the PC Networking
Tutorial on the NETGEAR CD.
To create an Ad Hoc mode profile:
1.Use the icon to open the Smart Wizard. The Settings page opens:
Figure 2-5
2-7
v2.0, February 2007
Page 32
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
2.Enter the network settings.
a.Select Computer-to-Computer (Ad Hoc) for the Network Type.
b.Select or enter the Network Name (SSID) for the Ad Hoc network.
c.In the Profile box, type the name of the profile.
d.Click Apply.
3.Save your settings in a Profile.
a.Click the Save Profile button.
All the configuration settings are saved in this profile.
b.Click Apply.
c.Click Close to exit the Smart Wizard, or Cancel to return to the previous settings.
4.Configure the PC network settings.
a.Configure each PC with either a static IP address or with the IPX protocol.
Note: For instructions on configuring static IP addresses, refer to the networking
tutorial on your NETGEAR CD.
b.Restart the PCs.
5.Verify wireless connectivity between your peer devices.
Use the Ping program:
a.On the Windows taskbar click the Start button, and then click Run.
Figure 2-6
2-8
v2.0, February 2007
Page 33
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
b.Assuming the target PC is configured with 192.168.0.1 as its IP address, type
ping -t 192.168.0.1 and then click OK.
c.This will cause a continuous ping to be sent to the device with the 192.168.0.1 static IP
address. The ping response should change to “reply.”
Figure 2-7
At this point the connection is established.
Note: If you cannot connect, see “Removing the WG111T Software” in Chapter 1. For
problems with accessing network resources, the Windows Client and File and Print
Sharing software might not be installed and configured properly on your
computers. See the link to “Internet Networking and TCP/IP Addressing” in
Appendix B.
Starting a Computer-to-Computer (Ad Hoc) Network Connection
1.On the Settings tab page of the Smart Wizard, select or type the Network Name (SSID).
2.Select the Computer-to-Computer (Ad Hoc) network type.
3.Click Initiate Ad Hoc. The Ad Hoc Setting dialog box opens:
Figure 2-8
4.In the Start Ad Hoc field, choose the wireless standard (802.1 1a, 802.1 1b, or 802.1 1g) for your
Ad Hoc computer-to-computer network.
2-9
v2.0, February 2007
Page 34
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
5.In the Channel field, Automatic should work. If you notice interference problems with another
nearby wireless device, select a channel that is not being used by any other wireless networks
near your wireless adapter. Use the Networks tab page to identify the channels in use in your
area.
6.Click OK.
Note: The channel number differs depending on the country. The connection speed
automatically defaults to the highest speed.
Wireless Security
Many networks use wireless security to encrypt wireless data communications. If you try to
connect to a network with wireless security the Smart Wizard detects it. Before you can use that
network you must set up the WG11 1T with exactly the same kind of wireless security settings. The
main types of wireless security used for home networks are:
In addition to the wireless security features, networks should use LAN network security features
such as requiring a user name and password to access the shared resources in the network.
Using Wireless Security Features
You can strengthen the security of your wireless connection by enabling Wired Equivalent Privacy
(WEP) encryption of the wireless data communications. Or, you can use WPA-PSK (Wi-Fi
Protected Access Pre-Shared Key) encryption. For more information about wireless security, see
the Web link to “Wireless Communications” in Appendix B.
In addition to the WG111T wireless security features, you should also configure appropriate LAN
network security features such as requiring a user name and password to access the shared
resources in your network.
2-10
v2.0, February 2007
Page 35
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Wireless Network Name (SSID) and Security Settings
Print this form, fill in the configuration parameters and put it in a safe place for possible future
reference. For an existing wireless network, the person who set up the network will be ab le to
provide this information.
•Network Name (SSID): The Service Set Identification (SSID) identifies the wireless local
area network. Any
(SSID). You may customize it using up to 32 alphanumeric characters. Write your customized
wireless network name (SSID) on the line below .
Note: The SSID in the wireless access point is the SSID you configure in the wireless
Wireless network name (SSID): ______________________________
(First available network)is the default WG111T wireless network name
USB adapter. For the access point and wireless nodes to communicate with
each other, all must be configured with the same SSID.
•If WEP Authentication is Used.
–WEP Encryption key size. Identify one: 64-bit or 128-bit. The encryption key size must
the wireless network settings.
–Data Encryption (WEP) Keys. There are two methods for creating WEP data encryption
keys. Whichever method you use, record the key values in the spaces below.
These characters are case
sensitive. Enter a word or group of printable characters and click the Generate Keys
button. Not all wireless devices support the passphrase method.
•Manual method. These values are not case sensitive. For 64-bit WEP, enter 10 hex
digits (any combination of 0-9 or a-f). For 128-bit WEP, enter 26 hex digits.
•If WPA2-PSK or WPA-PSK Authentication is Used.
–Passphrase: _________________________ _____
These characters are case sensitive.
Enter a word or group of printable characters. When y ou use WPA-PSK, the other devices
in the network will not connect unless they are set to WP A-PSK as well and are configured
with the correct Passphrase.
2-11
v2.0, February 2007
Page 36
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Setting up WEP Encryption Security
Follow the steps below to configure WEP Encryption Security.
1.Run the WG111T Smart Wizard.
a.Make sure the WG111T software is installed and the WG111T is connected to the USB
port in your computer.
b.Use the icon to open the Smart Wizard. The Settings tab page opens.
Figure 2-9
2.Configure the Security settings.
a.In the Profile box, select the profile or type in a profile name.
b.In the Network Name (SSID) field select the network, or enter the SSID.
Note: You will not get a wireless network connection unless the network SSID
matches exactly what is configured in the access point.
c.In the Security section, select WEP.
3.Select the WEP encryption strength you will use:
•64-bit WEP data encryption
•128-bit WEP data encryption
2-12
v2.0, February 2007
Page 37
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Note: Larger encryption keys require more processing and may slow the
communications response times.
4.Select Create with Passphrase and enter the passphrase. The configuration utility will
automatically generate the WEP keys.
Note: The characters are case sensitive. Be sure to use the same passphrase for all the
wireless devices in the network.
If the passphrase method is not available in the other devices, you must manually enter the
keys to match exactly what is in the access point and other 802.11b wireless devices.
5.Save your settings in a Profile.
a.Click the Save Profile button. All the configuration settings are saved in this profile.
b.Click Apply and then click Close to exit the configuration utility.
Setting up WPA2-PSK Security
Follow the steps below to configure WPA2-PSK Security.
1.Run the WG111T Smart Wizard.
a.Make sure the WG111T software is installed and the WG111T is fully inserted in a USB
port in your computer.
b.Use the icon to open the Smart Wizard. The Settings tab page opens.
2-13
v2.0, February 2007
Page 38
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
2.Configure the Security settings.
Figure 2-10
a.In the Profile box, select the profile or type in a profile name.
b.In the Network Name (SSID) field select the network, or enter the SSID.
Note: You will not get a wireless network connection unless the network SSID
matches exactly what is configured in the access point.
c.In the Security section, select WPA2-PSK [AES].
For more information about WPA2-PSK security, see the Web link to “Wireless
Communications” in Appendix B.
3.Save your settings in a Profile.
a.Click the Save Profile button. All the configuration settings are saved in this profile.
b.Click Apply and then click Close to exit the Smart Wizard.
Setting up WPA-PSK Security
Follow the steps below to configure WPA-PSK Security.
1.Run the WG111T Smart Wizard.
2-14
v2.0, February 2007
Page 39
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
a.Make sure the WG111T software is installed and the WG111T is fully inserted in a USB
port in your computer.
b.Use the icon to open the Smart Wizard. The Settings tab page opens.
Figure 2-11
2.Configure the Security settings.
a.In the Profile box, select the profile or type in a profile name.
b.In the Network Name (SSID) field select the network, or enter the SSID.
Note: You will not get a wireless network connection unless the network SSID
matches exactly what is configured in the access point.
c.In the Security section, select WPA-PSK [TKIP].
For more information, see the link to “Wireless Communications” in Appendix B.
3.Save your settings in a Profile.
a.Click the Save Profile button. All the configuration settings are saved in this profile.
b.Click Apply and then click Close to exit the Smart Wi zard.
2-15
v2.0, February 2007
Page 40
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Advanced Settings
The Advanced Settings should normally work in their default settings. On the Settings tab click the
Advanced Settings button to display the dialog box shown below:
Figure 2-12
Statistics Page
The Statistics page provides real-time and historical trend information on the data traffic and
performance of your wireless adapter.
Figure 2-13
•Transmit/Receive Performance (%): A real time graph identifying the total, receive, and
transmit utilization as a percentage the total possible.
2-16
v2.0, February 2007
Page 41
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
•Transmit, Receive, and Tota l (TxRx): Radio buttons let you select whether to display the
transmit performance, the receive performance, or both in the same graph.
•Transmit Statistics: Identifies transmit megabits per second (Mbps), transmit packets per
second (Tx Packets/s), total transmitted packets, and transmit errors.
•Receive S ta tistics: Identifies receive megabits per second (Mbps), receive packets per second
(Rx Packets/s), total received packets, and reception errors.
About Page
The About page displays the current software version information.
Figure 2-14
The following information is displayed in the About page:
•Regional Domain: This is the region setting for the wireless adapter. The approved channels
for the region are automatically scanned. Governments regulate the channels used for wireless
transmission. Operating the wireless adapter in a different region may violate local laws.
•Driver Version: The wireless adapter driver version.
•Driver Date: The wireless adapter driver release date.
2-17
v2.0, February 2007
Page 42
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
•MAC Address: The MAC address of the adapter. The Media Access Control address is a
unique 48-bit hardware address assigned to every network interface card. Some wireless
networks will restrict access based on a list of known MAC addresses. If you are
communicating with such a network, you would have to provide the address shown here to the
network administrator before you would be allowed to connect. Restricting access by MAC
address adds an obstacle against unwanted access to your network. However, unless you use
data encryption security, the data broadcast over the wireless link is fully exposed.
•IP Address: The IP address assigned to this adapter.
•Smart Wireless Utility: The version and release date of the Smart Wizard.
2-18
v2.0, February 2007
Page 43
Chapter 3
Troubleshooting
This chapter provides information about troubleshooting your NETGEAR 108 Mbps Wireless
USB 2.0 Adapter WG111T. For information about connecting to wireless networks and the
Internet, see “Connecting to Wireless Networks and the Internet” in Chapter 1.
Troubleshooting Tips
Use the information below to solve common problems you may encounter. Also, refer to the
knowledge base on the NETGEAR website at http://www.netgear.com/support/main.asp.
Table 3-1. Troubleshooting Tips
ProblemAction
The LED is not litThe WG111T is not connected to the USB port properly or the
WG111T software is not loaded.
• Remove and reinsert the WG111T.
• Check the Windows device manager to see if the WG111T is
recognized and enabled. Reload the WG111T software, if
necessary.
• Try to install the WG111T in a different USB slot on your
system if one is available.
The LED blinks but the WG111T is no t
connected to an access point.
I cannot connect to an access point.
The access point is available and there is
good signal strength.
The WG111T is tryi ng to connect to an access point, but
cannot connect.
• The access point may not be powered on.
• Or, the access point and the WG111T are not configured
with the same wireless parameters. Check the SSID and
WEP settings.
• If the access point is WPA-PSK protected, you need the
correct WPA-PSK passphrase. Otherwise, the WG111T will
still be connected to the previous access point and you will
not be able to change to the WPA-PSK access point.
• If the access point is WEP protected (either 64 or 128 bit
encryption), you will be prompted to enter the WEP
encryption security information.
3-1
v2.0, February 2007
Page 44
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Table 3-1. Troubleshooting Tips (continued)
ProblemAction
Throughput is only 54 Mbps or only 14
Mbps.
The Smart Wizard keeps asking me to save
settings.
Two WG111T icons are in the system tray.You have an older software version installed on your system
I can connect to the access point, but not
the other computers on the network or to
the Internet.
The WG111 108 Mbps Wireless USB 2.0 Adapter can operate
at faster speeds.
• At 54 Mbps you are probably connecting to a standard
802.11g network.
• If you do not have a USB 2.0 port on your PC, the
throughput is limited to the 14 Mbps of the USB 1.1
standard.
If you change the settings the Smart Wizard offers you the
chance to save the changes. To avoid this prompt, simply click
Apply before you close the Smart Wizard.
and it needs to be removed. See “Removing the WG111T
Software” in Chapter 1or “Upgrading the WG111T Software” in
Chapter 1.
This could be a physical layer problem or a network
configuration problem.
1. Check to make sure that the access point is physically
connected to the Ethernet network.
2. Make sure that the IP addresses and the Windows
networking parameters are all configured correctly. See
the link to “Internet Networking and TCP/IP Addressing” in
Appendix B
3. Restart the cable or DSL modem, router, access point, and
computer.
.
Viewing the IP address.To view the WG111 108 Mbps Wireless USB 2.0 Adapter IP
address, click the WG111T icon to open the Smart Wizard.
Then check the IP address in the About page.
No IP address is assigned to the WG111
108 Mbps Wireless USB 2.0 Adapter.
This may occur if you upgraded your WG111 108 Mbps
Wireless USB 2.0 Adapter software and did not reboot your
system.
• Either restart your computer, or connect to a different access
point.
• It does not usually help to shut down the Smart Wizard or
disable/enable the card.
3-2
v2.0, February 2007
Page 45
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
Ad Hoc Mode Is Not Working Correctly
You must click the Initiate Ad Hoc button before you click Apply. Here is how you start an Ad
Hoc network:
1.Fill in the Network Name (SSID).
2.Select the Computer-to-Computer (Ad Hoc) Network Type.
3.Click Initiate Ad Hoc.
4.Accept the default settings or make your changes and clic k OK
5.Click Apply.
Note: Be sure all computers in your Ad Hoc network are configured with static IP
addresses in the same subnet.
Windows XP Occasional Connection Problems
Windows XP users who apply Windows XP Hotfix (SP2) Q815485 from the Windows XP Update
Service may not be able to connect to the Internet, may have dropped wireless connections, or both
when using the WG111 108 Mbps Wireless USB 2.0 Adapter. You can delete this Hotfix from the
Add or Remove Program utility in the Control Panel.
To delete Windows XP Hotfix (SP2) Q815485:
1.Click Start, point to Control Panel, and then double click Add/Remove Programs.
2.Click Windows XP Hotfix (SP2) Q815485, and then click Remove.
•You may receive an error message that states that some program on the computer may not
work correctly if the update is removed.
•You can ignore this error message, and then click Yes to remove the update.
3.Restart your computer and rerun the Smart Display Setup Wizard.
This should solve your connection issue. You can restore this hotfix by following the link below:
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
3-4
v2.0, February 2007
Page 47
Appendix A
Technical Specifications
This appendix provides technical specifications for the NETGEAR 108 Mbps Wireless USB 2.0
Adapter WG111T.
Antennae1 Integrated internal antenna
Standards 802.11g, 802.11b
Radio Data Rate1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54, and 108 Mbps (Auto Rate Sensing)
Frequency2.4GHz to 2.5GHz CCK and OFDM Modulation
Power 5V Bus powered
EmissionsFCC, CE
Bus interfaceUSB 5V
Provided driversMicrosoft Vista, Windows XP, and Windows 2000
Operating Environment Operating temperature: 0 to 45 degree C
Encryption40-bit (also called 64-bit) and 128-bit WEP data encryption, WPA2-PSK,
and WPA-PSK
WarrantyLimited 1-year warranty
A-1
v2.0, February 2007
Page 48
NETGEAR 108 Mpbs Wireless USB 2.0 Adapter WG111T User Manual
A-2
v2.0, February 2007
Page 49
Appendix B
Related Documents
This appendix provides links to reference documents you can use to gain a more complete
understanding of the technologies used in your NETGEAR product.
Document Link
Windows XP and Vista
Wireless Configuration
Utilities