NETGEAR GSM7228PS-100NAS User Manual

ProSafe Managed Switch

Command Line Interface (CLI) User Manual

10.0 GSM7328Sv2 GSM7352Sv2 GSM7228PS GSM7252PS M5300-28G3

M5300-52G3 M5300-28G-POE+ M5300-52G-POE+ M5300-28GF3 M5300-28G M5300-52G

350 East Plumeria Drive San Jose, CA 95134 USA

November 2012 202-11054-02

1.0

ProSafe Managed Switch

into any language in any form or by any means without the written permission of NETGEAR, Inc.

Technical Support

Thank you for choosing NETGEAR. To register your product, get the latest product updates, or get support online, visit us at http://support.netgear.com.

Phone (US & Canada only): 1-888-NETGEAR Phone (Other Countries): See Support information card.

Trademarks

NETGEAR, the NETGEAR logo, ReadyNAS, ProSafe, Smart Wizard, Auto Uplink, X-RAID2, and NeoTV are trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, Windows NT, and Vista are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders.

Statement of Conditions

To improve internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use, or application of, the product(s) or circuit layout(s) described herein.

Revision History

Publication Part Number

202-11054-02 1.0 November 2012 Added mixed stacking commands. 202-11054-01 1.0 August 2012 Replaced the private group commands with

202-10936-02 1.0 January 2012 Added clear event log, ip local-proxy-arp, and

202-10936-01 1.0 November 2011 Added PoE and MVR mode features. 202-10515-05 1.1 June 2011 Added DHCPv6 and DHCPv6 mode features. 202-10515-04 1.0 November 2010 New document template. 202-10515-03 v 1.0 June 2010 Move some content to the Software Setup

202-10515-02 Software release 8.0.2: new firmware with

Version Publish Date Comments

private VLAN commands, replaced the Auto-Voice over IP Commands chapter, and added iSCSI commands.

spanning-tree auto-edge. Removed poe reset auto.

Guide.

DHCP L3 Relay, color conform policy, DHCP server in dynamic mode, and configuring a stacking port as an Ethernet port.

202-10515-01 Original publication.

Chapter 1 Using the Command-Line Interface

Chapter 2 Stacking Commands

Licensing and Command Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Command Syntax. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Command Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Common Parameter Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Unit/Slot/Port Naming Convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Using a Command’s “No” Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Managed Switch Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Command Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Command Completion and Abbreviation . . . . . . . . . . . . . . . . . . . . . . . . . .17

CLI Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

CLI Line-Editing Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Using CLI Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Accessing the CLI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Dedicated Port Stacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Stacking Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Non-Stop Forwarding Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Stack Firmware Synchronization Commands. . . . . . . . . . . . . . . . . . . . . . .35

Chapter 3 Switching Commands

Port Configuration Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Loopback Interface Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Spanning Tree Protocol (STP) Commands . . . . . . . . . . . . . . . . . . . . . . . .47

VLAN Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Double VLAN Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Voice VLAN Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Provisioning (IEEE 802.1p) Commands. . . . . . . . . . . . . . . . . . . . . . . . . . .82

Protected Ports Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Private Group Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

Private VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

GARP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

GVRP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92

GMRP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94

Port-Based Network Access Control Commands. . . . . . . . . . . . . . . . . . . .96

802.1X Supplicant Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109

Storm-Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112

Flow Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122

ProSafe Managed Switch

Port-Channel/LAG (802.3ad) Commands . . . . . . . . . . . . . . . . . . . . . . . .123

Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139

Static MAC Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141

DHCP L2 Relay Agent Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145

DHCP Client Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149

DHCP Snooping Configuration Commands. . . . . . . . . . . . . . . . . . . . . . .150

Dynamic ARP Inspection Commands . . . . . . . . . . . . . . . . . . . . . . . . . . .159

IGMP Snooping Configuration Commands . . . . . . . . . . . . . . . . . . . . . . .166

IGMP Snooping Querier Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . .177

MLD Snooping Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180

MLD Snooping Querier Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . .187

set mld querier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187

set mld querier query_interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188

set mld querier timer expiry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188

set mld querier election participate. . . . . . . . . . . . . . . . . . . . . . . . . . . .189

show mldsnooping querier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .189

Port Security Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190

LLDP (802.1AB) Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194

LLDP-MED Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203

Denial of Service Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212

MAC Database Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .222

ISDP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224

Priority-Based Flow Control Commands . . . . . . . . . . . . . . . . . . . . . . . . .229

Chapter 4 Multicast VLAN Registration (MVR)

About MVR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .232

MVR Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .232

Chapter 5 Routing Commands

Address Resolution Protocol (ARP) Commands . . . . . . . . . . . . . . . . . . .240

IP Routing Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .246

Router Discovery Protocol Commands . . . . . . . . . . . . . . . . . . . . . . . . . .263

Virtual LAN Routing Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .266

Virtual Router Redundancy Protocol Commands. . . . . . . . . . . . . . . . . . .267

DHCP and BOOTP Relay Commands. . . . . . . . . . . . . . . . . . . . . . . . . . .276

IP Helper Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .278

Open Shortest Path First (OSPF) Commands . . . . . . . . . . . . . . . . . . . . .282

OSPF Graceful Restart Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . .322

nsf. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323

nsf restart-interval. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323

nsf helper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324

nsf helper disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325

nsf [ietf] helper strict-lsa-checking . . . . . . . . . . . . . . . . . . . . . . . . . . . .325

OSPF Interface Flap Dampening Commands . . . . . . . . . . . . . . . . . . . . .327

Routing Information Protocol (RIP) Commands. . . . . . . . . . . . . . . . . . . .329

ICMP Throttling Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .336

ProSafe Managed Switch

Chapter 6 IP Multicast Commands

Multicast Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .339

DVMRP Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .344

PIM Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .349

Internet Group Message Protocol (IGMP) Commands. . . . . . . . . . . . . . .360

IGMP Proxy Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .367

Chapter 7 IPv6 Commands

Tunnel Interface Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .373

IPv6 Routing Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .375

OSPFv3 Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .398

OSPFv3 Graceful Restart Commands . . . . . . . . . . . . . . . . . . . . . . . . . . .429

DHCPv6 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .431

Chapter 8 IPv6 Multicast Commands

IPv6 Multicast Forwarder Commands . . . . . . . . . . . . . . . . . . . . . . . . . . .439

IPv6 PIM Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .442

IPv6 MLD Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .449

IPv6 MLD-Proxy Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .455

Chapter 9 Quality of Service (QoS) Commands

Class of Service (CoS) Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .461

Differentiated Services (DiffServ) Commands . . . . . . . . . . . . . . . . . . . . .469

DiffServ Class Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .470

DiffServ Policy Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .479

DiffServ Service Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .484

DiffServ Show Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .485

MAC Access Control List (ACL) Commands . . . . . . . . . . . . . . . . . . . . . .491

IP Access Control List (ACL) Commands. . . . . . . . . . . . . . . . . . . . . . . . .495

IPv6 Access Control List (ACL) Commands. . . . . . . . . . . . . . . . . . . . . . .502

Time Range Commands for Time-Based ACLs. . . . . . . . . . . . . . . . . . . .506

AutoVOIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .508

iSCSI Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .512

Chapter 10 Power over Ethernet (PoE) Commands

About PoE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .518

PoE Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .519

Chapter 11 Utility Commands

Auto Install Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .530

Dual Image Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .532

System Information and Statistics Commands. . . . . . . . . . . . . . . . . . . . .534

Logging Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .550

Email Alerting and Mail Server Commands . . . . . . . . . . . . . . . . . . . . . . .556

ProSafe Managed Switch

System Utility and Clear Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . .562

Simple Network Time Protocol (SNTP) Commands. . . . . . . . . . . . . . . . .572

DHCP Server Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .579

DNS Client Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .591

Packet Capture Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .595

Serviceability Packet Tracing Commands . . . . . . . . . . . . . . . . . . . . . . . .598

Cable Test Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .617

sFlow Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .617

Software License Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .622

IP Address Conflict Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .623

Link Local Protocol Filtering Commands . . . . . . . . . . . . . . . . . . . . . . . . .624

RMON Stats and History Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . .625

UDLD Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .631

Chapter 12 Management Commands

Configuring the Switch Management CPU. . . . . . . . . . . . . . . . . . . . . . . .636

Network Interface Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .638

Console Port Access Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .641

Telnet Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .643

Secure Shell (SSH) Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .648

Management Security Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .651

Hypertext Transfer Protocol (HTTP) Commands . . . . . . . . . . . . . . . . . . .652

Access Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .659

User Account Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .659

SNMP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .683

RADIUS Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .694

TACACS+ Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706

Configuration Scripting Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .711

Pre-Login Banner and System Prompt Commands. . . . . . . . . . . . . . . . .713

Switch Database Management (SDM) Templates. . . . . . . . . . . . . . . . . .714

IPv6 Management Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .716

Chapter 13 Log Messages

Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .722

Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .724

Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .726

Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .730

QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .736

Routing/IPv6 Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .737

Multicast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .740

Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .742

Technologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .743

O/S Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .745

Chapter 14 Captive Portal Commands

Captive Portal Global Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .747

ProSafe Managed Switch

Captive Portal Configuration Commands. . . . . . . . . . . . . . . . . . . . . . . . .751

Captive Portal Status Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .757

Captive Portal Client Connection Commands . . . . . . . . . . . . . . . . . . . . .761

Captive Portal Interface Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . .765

Captive Portal Local User Commands . . . . . . . . . . . . . . . . . . . . . . . . . . .766

Captive Portal User Group Commands . . . . . . . . . . . . . . . . . . . . . . . . . .772

Chapter 15 Command List Index

1. Using the Command-Line Interface

The command-line interface (CLI) is a text-based way to manage and monitor the system. You can access the CLI by using a direct serial connection or by using a remote logical connection with telnet or SSH.

This chapter describes the CLI syntax, conventions, and modes. It contains the following sections:

• Licensing and Command Support

• Command Syntax

• Command Conventions

• Common Parameter Values

• Unit/Slot/Port Naming Convention

• Using a Command’s “No” Form

• Managed Switch Modules

• Command Modes

• Command Completion and Abbreviation

• CLI Error Messages

• CLI Line-Editing Conventions

• Using CLI Help

• Accessing the CLI

Licensing and Command Support

As shown in the following table, some command groups or commands require a license and some are supported on particular switch models. For those requiring a license, license keys are available from your VAR or NETGEAR authorized e-commerce portal. License activation is described in the Software Setup Manual.

ProSafe Managed Switch

Command Group or Command

Stacking Commands Supported Supported Supported Supported Supported Non-Stop Forwarding

Commands Stack Firmware

Synchronization Commands

Router Discovery Protocol Commands

Virtual Router Redundancy Protocol Commands

Open Shortest Path First (OSPF) Commands

OSPF Graceful Restart Commands

Routing Information Protocol (RIP) Commands

Tunnel Interface Commands

M5300-28G-POE+ M5300-52G-POE+

Supported Supported Supported Supported Supported

Require license Require license Supported Supported Require license

M5300-28G M5300-52G

M5300-28G3 M5300-52G3 M5300-28GF3

GSM7328Sv2 GSM7352Sv2

GSM7228PS GSM7252PS

IPv6 Routing Commands Require license Require license Supported Supported Require license OSPFv3 Commands Require license Require license Supported Supported Require license OSPFv3 Graceful Restart

Commands DHCPv6 Commands Require license Require license Supported Supported Require license Multicast Commands Require license Require license Supported Supported Require license DVMRP Commands Require license Require license Supported Supported Require license PIM Commands Require license Require license Supported Supported Require license Internet Group Message

Protocol (IGMP) Commands

IGMP Proxy Commands Require license Require license Supported Supported Require license IPv6 Multicast Forwarder

Commands IPv6 PIM Commands Require license Require license Supported Supported Require license IPv6 MLD Commands Require license Require license Supported Supported Require license

Require license Require license Supported Supported Require license

Using the Command-Line Interface

ProSafe Managed Switch

Command Group or Command

IPv6 MLD-Proxy Commands

PoE Commands Supported Not Supported Not Supported Not Supported Supported MVR Commands Supported Supported Supported Not Supported Not Supported Link Local Protocol Filtering

Commands Priority-Based Flow Control

Commands Captive Portal Commands Supported Supported Supported Supported Supported cos-queue random-detect Supported Supported Supported Supported Supported no cos-queue

random-detect random-detect exponential

weighting-constant no random-detect

exponential weighting-constant

M5300-28G-POE+ M5300-52G-POE+

Require license Require license Supported Supported Require license

Supported Supported Supported Supported Supported

Not Supported Not Supported Not Supported Not Supported Not Supported

Supported Supported Supported Supported Supported

M5300-28G M5300-52G

M5300-28G3 M5300-52G3 M5300-28GF3

GSM7328Sv2 GSM7352Sv2

GSM7228PS GSM7252PS

random-detect queue-parms

no random-detect queue-parms

Command Syntax

Format network parms <ipaddr> <netmask> [gateway]

Supported Supported Supported Supported Supported

A command is one or more words that might be followed by one or more parameters. Parameters can be required or optional values.

Some commands, such as show network or clear vlan, do not require parameters. Other commands, such as network parms, require that you supply a value after the command. You must type the parameter values in a specific order, and optional parameters follow required parameters. The following example describes the network parms command syntax:

• network parms is the command name.

• <ipaddr> and <netmask> are parameters and represent required values that you must

enter after you type the command keywords.

Using the Command-Line Interface

ProSafe Managed Switch

• [gateway] is an optional parameter, so you are not required to enter a value in place of

the parameter.

The New Template User Manual lists each command by the command name and provides a brief description of the command. Each command reference also contains the following information:

• Format shows the command keywords and the required and optional parameters.

• Mode identifies the command mode you must be in to access the command.

• Default shows the default value, if any, of a configurable setting on the device.

The show commands also contain a description of the information that the command shows.

Command Conventions

In this document, the command name is in bold font. Parameters are in italic font. You must replace the parameter name with an appropriate value, which might be a name or number. Parameters are order dependent.

The parameters for a command might include mandatory values, optional values, or keyword choices. Table 1 describes the conventions this document uses to distinguish between value types.

Table 1. Parameter Conventions

Symbol Example Description

<> angle brackets

[] square brackets Indicates an optional parameter that you can enter in

{} curly braces Indicates that you must select a parameter from the list of

| Vertical bars Separates the mutually exclusive choices. [{}] Braces within

square brackets

<value>

[value]

{choice1 | choice2}

choice1 | choice2

[{choice1 | choice2}]

Indicates that you must enter a value in place of the brackets and text inside them.

place of the brackets and text inside them.

choices.

Indicates a choice within an optional element.

Common Parameter Values

Parameter values might be names (strings) or numbers. To use spaces as part of a name parameter, enclose the name value in double quotes. For example, the expression “System

Using the Command-Line Interface

ProSafe Managed Switch

Name with Spaces” forces the system to accept the spaces. Empty strings (““) are not valid user-defined strings. Table 2 describes common parameter values and value formatting.

Table 2. Parameter Descriptions

Parameter Description

ipaddr This parameter is a valid IP address. You can enter the IP address in the following formats:

a (32 bits) a.b (8.24 bits) a.b.c (8.8.16 bits) a.b.c.d (8.8.8.8)

In addition to these formats, the CLI accepts decimal, hexadecimal and octal formats through the following input formats (where n is any valid hexadecimal, octal or decimal number):

0xn (CLI assumes hexadecimal format) 0n (CLI assumes octal format with leading zeros) n (CLI assumes decimal format)

ipv6-address

FE80:0000:0000:0000:020F:24FF:FEBF:DBCB, or FE80:0:0:0:20F:24FF:FEBF:DBCB, or FE80::20F24FF:FEBF:DBCB, or FE80:0:0:0:20F:24FF:128:141:49:32

For additional information, refer to RFC 3513.

Interface or unit/slot/port

Logical Interface

Character strings Use double quotation marks to identify character strings, for example, “System Name with

Valid slot and port number separated by forward slashes. For example, 0/1 represents slot number 0 and port number 1.

Represents a logical slot and port number. This is applicable in the case of a port-channel (LAG). You can use the logical unit/slot/port to configure the port-channel.

Spaces”. An empty string (“”) is not valid.

Unit/Slot/Port Naming Convention

Managed switch software references physical entities such as cards and ports by using a unit/slot/port naming convention. The software also uses this convention to identify certain logical entities, such as Port-Channel interfaces.

The slot number has two uses. In the case of physical ports, it identifies the card containing the ports. In the case of logical and CPU ports it also identifies the type of interface or port.

Table 3. Type of Slots

Slot Type Description

Physical slot numbers Physical slot numbers begin with zero, and are allocated up to the maximum

number of physical slots.

Logical slot numbers Logical slots immediately follow physical slots and identify port-channel (LAG) or

router interfaces.

CPU slot numbers The CPU slots immediately follow the logical slots.

Using the Command-Line Interface

ProSafe Managed Switch

The port identifies the specific physical port or logical interface being managed on a given slot.

Table 4. Type of Ports

Port Type Description

Physical Ports The physical ports for each slot are numbered sequentially starting from zero. Logical Interfaces Port-channel or Link Aggregation Group (LAG) interfaces are logical interfaces

that are only used for bridging functions. VLAN routing interfaces are only used for routing functions. Loopback interfaces are logical interfaces that are always up. Tunnel interfaces are logical point-to-point links that carry encapsulated packets.

CPU ports CPU ports are handled by the driver as one or more physical entities located on

physical slots.

Note: In the CLI, loopback and tunnel interfaces do not use the

unit/slot/port format. To specify a loopback interface, you use the loopback ID. To specify a tunnel interface, you use the tunnel ID.

Using a Command’s “No” Form

The no keyword is a specific form of an existing command and does not represent a new or distinct command. Almost every configuration command has a no form. In general, use the no form to reverse the action of a command or reset a value back to the default. For example, the no shutdown configuration command reverses the shutdown of an interface. Use the command without the keyword no to re-enable a disabled feature or to enable a feature that is disabled by default. Only the configuration commands are available in the no form.

Managed Switch Modules

Managed switch software consists of flexible modules that can be applied in various combinations to develop advanced Layer 2/3/4+ products. The commands and command modes available on your switch depend on the installed modules. Additionally, for some show commands, the output fields might change based on the modules included in the software.

The software suite includes the following modules:

• Switching (Layer 2)

• Routing (Layer 3)

• IPv6—IPv6 routing

• Multicast

Using the Command-Line Interface

ProSafe Managed Switch

• Quality of Service

• Management (CLI, Web UI, and SNMP)

• IPv6 Management—Allows management of the device through an IPv6 through an IPv6

address without requiring the IPv6 Routing package in the system. The management address can be associated with the network port (front-panel switch ports) and a routine interface (port or VLAN).

• Stacking

Not all modules are available for all platforms or software releases.

Command Modes

The CLI groups commands into modes according to the command function. Each of the command modes supports specific software commands. The commands in one mode are not available until you switch to that particular mode, with the exception of the User EXEC mode commands. You can execute the User EXEC mode commands in the Privileged EXEC mode.

The command prompt changes in each command mode to help you identify the current mode.

Table 5 describes the command modes and the prompts visible in that mode.

Note: The command modes available on your switch depend on the

software modules that are installed. For example, a switch that does not support BGPv4 does not have the Router BGPv4 Command Mode.

Table 5. CLI Command Modes

Command Mode Prompt Mode Description

User EXEC

Privileged EXEC

Global Config

VLAN Config

Switch>

Switch#

Switch (Config)#

Switch (Vlan)#

Contains a limited set of commands to view basic system information.

Allows you to issue any EXEC command, enter the VLAN mode, or enter the Global Configuration mode.

Groups general setup commands and permits you to make modifications to the running configuration.

Groups all the VLAN commands.

Using the Command-Line Interface

ProSafe Managed Switch

Table 5. CLI Command Modes (Continued)

Command Mode Prompt Mode Description

Interface Config Switch (Interface <unit/slot/port>)#

Switch (Interface Loopback <id>)#

Switch (Interface Tunnel <id>)#

Line Config Switch (line)# Contains commands to configure outbound

Policy Map Config

Policy Class Config

Class Map Config Switch (Config-class-map)# Contains the QoS class map configuration

Ipv6_Class-Map Config

Router OSPF Config

Router OSPFv3 Config

Switch (Config-policy-map)# Contains the QoS Policy-Map configuration

Switch (Config-policy-class-map)# Consists of class creation, deletion, and

Switch (Config-class-map)# Contains the QoS class map configuration

Switch (Config-router)# Contains the OSPF configuration commands.

Switch (Config rtr)# Contains the OSPFv3 configuration commands.

Manages the operation of an interface and provides access to the router interface configuration commands.

Use this mode to set up a physical port for a specific logical connection operation.

telnet settings and console interface settings.

commands.

matching commands. The class match commands specify Layer 2, Layer 3, and general match criteria.

commands for IPv4.

commands for IPv6.

Router RIP Config Switch (Config-router)# Contains the RIP configuration commands. MAC Access-list

Config

TACACS Config Switch (Tacacs)# Contains commands to configure properties for

DHCP Pool Config

DHCPv6 Pool Config

Stack Global Config Mode

ARP Access-List Config Mode

Switch (Config-mac-access-list)# Allows you to create a MAC Access-List and to

enter the mode containing MAC Access-List configuration commands.

the TACACS servers.

Switch (Config dhcp-pool)# Contains the DHCP server IP address pool

configuration commands.

Switch (Config dhcp6-pool)# Contains the DHCPv6 server IPv6 address pool

configuration commands.

Switch (Config stack)# Allows you to access the Stack Global Config

Mode.

Switch (Config-arp-access-list)# Contains commands to add ARP ACL rules in

an ARP Access List.

Using the Command-Line Interface

ProSafe Managed Switch

Table 6 explains how to enter or exit each mode.

Table 6. CLI Mode Access and Exit

Command Mode Access Method Exit or Access Previous Mode

User EXEC This is the first level of access. To exit, enter logout. Privileged EXEC From the User EXEC mode, enter

enable.

Global Config From the Privileged EXEC mode,

enter configure.

VLAN Config From the Privileged EXEC mode,

enter vlan database.

Interface Config From the Global Config mode,

enter interface <unit/slot/port> or interface loopback <id> or interface tunnel <id>

Line Config From the Global Config mode,

enter lineconfig.

Policy-Map Config

Policy-Class-Map Config

Class-Map Config

From the Global Config mode, enter policy-map <name> in.

From the Policy Map mode enter class.

From the Global Config mode, enter class-map, and specify the optional keyword ipv4 to specify the Layer 3 protocol for this class. See class-map on page 470 for more information.

To exit to the User EXEC mode, enter exit or press Ctrl-Z.

To exit to the Privileged EXEC mode, enter exit, or press Ctrl-Z.

To exit to the Global Config mode, enter exit. To return to the Privileged EXEC mode, enter Ctrl-Z.

To exit to the Policy Map mode, enter exit. To return to the Privileged EXEC mode, enter Ctrl-Z.

To exit to the Global Config mode, enter exit. To return to the Privileged EXEC mode, enter Ctrl-Z.

Ipv6-Class-Map Config

Router OSPF Config

Router OSPFv3 Config

From the Global Config mode, enter class-map and specify the optional keyword ipv6 to specify the Layer 3 protocol for this class. See class-map on page 470 for more information.

From the Global Config mode, enter router ospf.

From the Global Config mode, enter ipv6 router ospf.

To exit to the Global Config mode, enter exit. To return to the Privileged EXEC mode, enter Ctrl-Z.

Using the Command-Line Interface

ProSafe Managed Switch

Table 6. CLI Mode Access and Exit (Continued)

Command Mode Access Method Exit or Access Previous Mode

Router RIP Config

MAC Access-list Config

TACACS Config From the Global Config mode,

DHCP Pool Config

DHCPv6 Pool Config

Stack Global Config Mode

ARP Access-List Config Mode

From the Global Config mode, enter router rip.

From the Global Config mode, enter

mac access-list extended

<name>.

enter tacacs-server host <ip-addr>, where <ip-addr> is the IP address of the TACACS server on your network.

From the Global Config mode, enter ip dhcp pool <pool-name>.

From the Global Config mode, enter ip dhcpv6 pool <pool-name>.

From the Global Config mode, enter the stack command.

From the Global Config mode, enter the

command.

arp access-list

To exit to the Global Config mode, enter exit. To return to the Privileged EXEC mode, enter Ctrl-Z.

To exit to the Global Config mode, enter the exit command. To return to the Privileged EXEC mode, enter Ctrl-Z.

To exit to the Global Config mode, enter the

exit command. To return to the Privileged

EXEC mode, enter

Ctrl-Z.

Command Completion and Abbreviation

Command completion finishes spelling the command when you type enough letters of a command to uniquely identify the command keyword. Once you have entered enough letters, press the SPACEBAR or TAB key to complete the word.

Command abbreviation allows you to execute a command when you have entered there are enough letters to uniquely identify the command. You must enter all of the required keywords and parameters before you enter the command.

Using the Command-Line Interface

ProSafe Managed Switch

CLI Error Messages

If you enter a command and the system is unable to execute it, an error message appears.

Table 7 describes the most common CLI error messages.

Table 7. CLI Error Messages

Message Text Description

% Invalid input detected at '^' marker. Indicates that you entered an incorrect or unavailable command.

The carat (^) shows where the invalid text is detected. This message also appears if any of the parameters or values are not recognized.

Command not found / Incomplete command. Use ? to list commands.

Ambiguous command Indicates that you did not enter enough letters to uniquely identify

Indicates that you did not enter the required keywords or values.

the command.

CLI Line-Editing Conventions

Table 8 describes the key combinations you can use to edit commands or increase the speed

of command entry. You can access this list from the CLI by entering help from the User or Privileged EXEC modes.

Table 8. CLI Editing Conventions

Key Sequence Description

DEL or Backspace Delete previous character Ctrl-A Go to beginning of line Ctrl-E Go to end of line Ctrl-F Go forward one character Ctrl-B Go backward one character Ctrl-D Delete current character Ctrl-U, X Delete to beginning of line Ctrl-K Delete to end of line Ctrl-W Delete previous word Ctrl-T Transpose previous character Ctrl-P Go to previous line in history buffer Ctrl-R Rewrites or pastes the line Ctrl-N Go to next line in history buffer

Using the Command-Line Interface

ProSafe Managed Switch

Table 8. CLI Editing Conventions (Continued)

Key Sequence Description

Ctrl-Y Prints last deleted character Ctrl-Q Enables serial flow Ctrl-S Disables serial flow Ctrl-Z Return to root command prompt Tab, <SPACE> Command-line completion Exit Go to next lower command prompt ? List available commands, keywords, or parameters

Using CLI Help

Enter a question mark (?) at the command prompt to display the commands available in the current mode.

(switch) >?

enable Enter into user privilege mode. help Display help for various special keys. logout Exit this session. Any unsaved changes are lost. ping Send ICMP echo packets to a specified IP address. quit Exit this session. Any unsaved changes are lost. show Display Switch Options and Settings. telnet Telnet to a remote host.

Enter a question mark (?) after each word you enter to display available command keywords or parameters.

(switch) #network ?

javamode Enable/Disable. mgmt_vlan Configure the Management VLAN ID of the switch. parms Configure Network Parameters of the router. protocol Select DHCP, BootP, or None as the network config protocol.

If the help output shows a parameter in angle brackets, you must replace the parameter with a value.

(switch) #network parms ?

<ipaddr> Enter the IP address.

If there are no additional command keywords or parameters, or if additional parameters are optional, the following message appears in the output:

<cr> Press Enter to execute the command

Using the Command-Line Interface

ProSafe Managed Switch

You can also enter a question mark (?) after typing one or more characters of a word to list the available command or parameters that begin with the letters, as shown in the following example:

(switch) #show m?

mac-addr-table mac-address-table monitor

Accessing the CLI

You can access the CLI by using a direct console connection or by using a telnet or SSH connection from a remote management host.

For the initial connection, you must use a direct connection to the console port. You cannot access the system remotely until the system has an IP address, subnet mask, and default gateway. You can set the network configuration information manually, or you can configure the system to accept these settings from a BOOTP or DHCP server on your network. For more information, see

Network Interface Commands on page 638.

Using the Command-Line Interface

2. Stacking Commands

This chapter contains the following sections:

• Dedicated Port Stacking

• Stacking Commands

• Non-Stop Forwarding Commands

• Stack Firmware Synchronization Commands

The commands in this chapter are in two functional groups:

• Show commands display switch settings, statistics, and other information.

• Configuration commands configure features and options of the switch. For every

configuration command, there is a show command that displays the configuration setting. The Primary Management Unit is the unit that controls the stack.

Note: When configuring a stack using M5300 Series switches and

GSM7328S V2H1, GSM7352S V2H1, GSM7228PS V1H1, or GSM7228PS V1H1switches, refer to on page 715.

sdm prefer (Mixed Stacking)

Dedicated Port Stacking

This section describes the commands you use to configure dedicated port stacking.

stack

This command sets the mode to Stack Global Config.

Format stack Mode Global Config

member

This command configures a switch. The <unit> is the switch identifier of the switch to be added/removed from the stack. The <switchindex> is the index into the database of the

ProSafe Managed Switch

supported switch types, indicating the type of the switch being preconfigured. The switch index is a 32-bit integer. This command is executed on the Primary Management Unit.

Format member <unit> <switchindex> Mode Stack Global Config

Note: Switch index can be obtained by executing the show supported

switchtype command in User EXEC mode.

no member

This command removes a switch from the stack. The <unit> is the switch identifier of the switch to be removed from the stack. This command is executed on the Primary Management Unit.

Format no member <unit> Mode Stack Global Config

switch priority

This command configures the ability of a switch to become the Primary Management Unit. The <unit> is the switch identifier. The <value> is the preference parameter that allows the user to specify, priority of one backup switch over another. The range for priority is 1 to

15. The switch with the highest priority value will be chosen to become the Primary Management Unit if the active Primary Management Unit fails. The switch priority defaults to the hardware management preference value 1. Switches that do not have the hardware capability to become the Primary Management Unit are not eligible for management.

Default enabled Format switch <unit> priority <value> Mode Global Config

switch renumber

This command changes the switch identifier for a switch in the stack. The <oldunit> is the current switch identifier on the switch whose identifier is to be changed. The <newunit> is the updated value of the switch identifier. Upon execution, the switch will be configured with the configuration information for the new switch, if any. The old switch configuration information will be retained, however the old switch will be operationally unplugged. This command is executed on the Primary Management Unit.

Stacking Commands

ProSafe Managed Switch

Note: If the management unit is renumbered, then the running

configuration is no longer applied (that is, the stack acts as if the configuration had been cleared).

Format switch <oldunit> renumber <newunit> Mode Global Config

movemanagement

This command moves the Primary Management Unit functionality from one switch to another. The <fromunit> is the switch identifier on the current Primary Management Unit. The <tounit> is the switch identifier on the new Primary Management Unit. Upon execution, the entire stack (including all interfaces in the stack) is unconfigured and reconfigured with the configuration on the new Primary Management Unit. After the reload is complete, all stack management capability must be performed on the new Primary Management Unit. To preserve the current configuration across a stack move, execute the copy system:running-config nvram:startup-config (in Privileged EXEC) command before performing the stack move. A stack move causes all routes and layer 2 addresses to be lost. This command is executed on the Primary Management Unit. The system prompts you to confirm the management move.

Note: The movemanagement command does not NSF (non-stop

forwarding). To move the management unit to the backup unit, use initiate failover instead. For more information, see

failover on page 33.

Format movemanagement <fromunit> <tounit> Mode Stack Global Config

standby

Use this command to configure a unit as a Standby Management Unit (STBY).

Format standby <unit number> Mode Stack Global Config

initiate

Stacking Commands

ProSafe Managed Switch

Note: The Standby Management Unit cannot be the current Management

Unit. The Standby unit should be a management-capable unit.

slot

This command configures a slot in the system. The <unit/slot> is the slot identifier of the slot. The <cardindex> is the index into the database of the supported card types, indicating the type of the card being preconfigured in the specified slot. The card index is a 32-bit integer. If a card is currently present in the slot that is unconfigured, the configured information will be deleted and the slot will be re-configured with default information for the card.

Format slot <unit/slot> <cardindex> Mode Global Config

Note: Card index can be obtained by executing show supported cardtype

command in User EXEC mode.

no slot

This command removes configured information from an existing slot in the system.

Format no slot <unit/slot> <cardindex> Mode Global Config

Note: Card index can be obtained by executing show supported cardtype

command in User EXEC mode.

set slot disable

This command configures the administrative mode of the slot(s). If you specify [all], the command is applied to all slots, otherwise the command is applied to the slot identified by <unit/slot>.

If a card or other module is present in the slot, this administrative mode will effectively be applied to the contents of the slot. If the slot is empty, this administrative mode will be applied

Stacking Commands

ProSafe Managed Switch

to any module that is inserted into the slot. If a card is disabled, all the ports on the device are operationally disabled and shown as “unplugged” on management screens.

Format set slot disable [<unit/slot> | all] Mode Global Config

no set slot disable

This command unconfigures the administrative mode of the slot(s). If you specify [all], the command removes the configuration from all slots, otherwise the configuration is removed from the slot identified by <unit/slot>.

If a card or other module is present in the slot, this administrative mode removes the configuration from the contents of the slot. If the slot is empty, this administrative mode removes the configuration from any module inserted into the slot. If a card is disabled, all the ports on the device are operationally disabled and shown as “unplugged” on management screens.

Format no set slot disable [<unit/slot> | all] Mode Global Config

set slot power

This command configures the power mode of the slot(s) and allows power to be supplied to a card located in the slot. If you specify [all], the command is applied to all slots, otherwise the command is applied to the slot identified by <unit/slot>.

Use this command when installing or removing cards. If a card or other module is present in this slot, the power mode is applied to the contents of the slot. If the slot is empty, the power mode is applied to any card inserted into the slot.

Format set slot power [<unit/slot> | all] Mode Global Config

no set slot power

This command unconfigures the power mode of the slot(s) and prohibits power from being supplied to a card located in the slot. If you specify [all], the command prohibits power to all slots, otherwise the command prohibits power to the slot identified by <unit/slot>.

Use this command when installing or removing cards. If a card or other module is present in this slot, power is prohibited to the contents of the slot. If the slot is empty, power is prohibited to any card inserted into the slot.

Format no set slot power [<unit/slot> | all] Mode Global Config

Stacking Commands

ProSafe Managed Switch

reload (Stack)

This command resets the entire stack or the identified <unit>. The <unit> is the switch identifier. The system prompts you to confirm that you want to reset the switch.

Format reload [<unit>] Mode User EXEC

show slot

This command displays information about all the slots in the system or for a specific slot.

Format show slot [<unit/slot>] Mode User EXEC

Term Definition Slot The slot identifier in a <unit/slot> format. Slot Status The slot is empty, full, or has encountered an error Admin State The slot administrative mode is enabled or disabled. Power State The slot power mode is enabled or disabled. Configured Card

Model Identifier Pluggable Cards are pluggable or non-pluggable in the slot. Power Down Indicates whether the slot can be powered down.

The model identifier of the card preconfigured in the slot. Model Identifier is a 32-character field used to identify a card.

If you supply a value for <unit/slot>, the following additional information appears:

Term Definition Inserted Card

Model Identifier Inserted Card

Description Configured Card

Description

The model identifier of the card inserted in the slot. Model Identifier is a 32-character field used to identify a card. This field is displayed only if the slot is full.

The card description. This field is displayed only if the slot is full.

The card description of the card preconfigured in the slot.

Stacking Commands

ProSafe Managed Switch

show supported cardtype

This commands displays information about all card types or specific card types supported in the system.

Format show supported cardtype [<cardindex>] Mode User EXEC

If you do not supply a value for <cardindex>, the following output appears:

Term Definition Card Index (CID) The index into the database of the supported card types. This index is used when

preconfiguring a slot.

Card Model Identifier

The model identifier for the supported card type.

If you supply a value for <cardindex>, the following output appears:

Term Definition Card Type The 32-bit numeric card type for the supported card. Model Identifier The model identifier for the supported card type. Card Description The description for the supported card type.

show switch

This command displays information about all units in the stack or a single unit when you specify the unit value. For units that would normally be allowed to join the stack but do not have a matching stack template ID, their switch status is shown as “STM Mismatch.”

Format show switch [<unit>] Mode Privileged EXEC

Term Definition Switch The unit identifier assigned to the switch.

When you do not specify a value for <unit>, the following information appears:

Term Definition Management

Status Preconfigured

Model Identifier

Indicates whether the switch is the Primary Management Unit, a stack member, or the status is unassigned.

The model identifier of a preconfigured switch ready to join the stack. The Model Identifier is a 32-character field assigned by the device manufacturer to identify the device.

Stacking Commands

Term Definition

ProSafe Managed Switch

Plugged-In Model Identifier

Switch Status The switch status. Possible values for this state are: OK, Unsup ported, Code

Code Version The detected version of code on this switch.

The model identifier of the switch in the stack. Model Identifier is a 32-character field assigned by the device manufacturer to identify the device.

Mismatch, Config Mismatch, or Not Present.

When you specify a value for <unit>, the following information appears:

Term Definition Management

Status Hardware

Management Preference

Admin Management Preference

Switch Type The 32-bit numeric switch type. Model Identifier The model identifier for this switch. Model Identifier is a 32-character field assigned by

Indicates whether the switch is the Primary Management Unit, a stack member, or the status is unassigned.

The hardware management preference of the switch. The hardware management preference can be disabled or unassigned.

The administrative management preference value assigned to the switch. This preference value indicates how likely the switch is to be chosen as the Primary Management Unit.

the device manufacturer to identify the device.

Switch Status The switch status. Possible values are OK, Unsupported, Code Mismatch, Config

Mismatch, or Not Present.

Switch Description

Expected Code Version

Detected Code Version

Detected Code in Flash

Stack Template ID The ID of the stack template currently in use. For example: 3. Stack Template

Description Up Time The system up time.

The switch description.

The expected code version.

The version of code running on this switch. If the switch is not present and the data is from pre-configuration, then the code version is “None”.

The version of code that is currently stored in FLASH memory on the switch. This code executes after the switch is reset. If the switch is not present and the data is from pre-configuration, then the code version is “None”.

The stack template description. For example: v1 and v2 Mix.

Stacking Commands

ProSafe Managed Switch

show supported switchtype

This commands displays information about all supported switch types or a specific switch type.

Format show supported switchtype [<switchindex>] Modes

• User EXEC

• Privileged EXEC

If you do not supply a value for <switchindex>, the following output appears:

Term Definition Switch Index (SID) The index into the database of supported switch types. This index is used when

preconfiguring a member to be added to the stack.

Model Identifier The model identifier for the supported switch type. Management

Preference Code Version The code load target identifier of the switch type.

The management preference value of the switch type.

If you supply a value for <switchindex>, the following output appears:

Term Definition Switch Type The 32-bit numeric switch type for the supported switch. Model Identifier The model identifier for the supported switch type. Switch

Description

The description for the supported switch type.

Stacking Commands

This section describes the commands you use to view and configure stacking information.

stack-port

This command sets stacking per port to either stack or ethernet mode.

Default stack Format stack-port <unit/slot/port> [{ethernet | stack}] Mode Stack Global Config

Stacking Commands

ProSafe Managed Switch

show stack-port

This command displays summary stack-port information for all interfaces.

Format show stack-port Mode Privileged EXEC

Term Definition QOS Mode Stacking QOS Mode for all Interfaces.

For Each Interface:

Term Definition Unit The unit number. Interface The slot and port numbers. Configured Stack

Mode Running Stack

Mode Link Status Status of the link. Link Speed Speed (Gbps) of the stack port link.

Stack or Ethernet.

show stack-port counters

This command displays summary data counter information for all interfaces.

Format show stack-port counters Mode Privileged EXEC

Term Definition Unit The unit number. Interface The slot and port numbers. Tx Data Rate Trashing data rate in megabits per second on the stacking port. Tx Error Rate Platform-specific number of transmit errors per second. Tx Total Error Platform-specific number of total transmit errors since power-up. Rx Data Rate Receive data rate in megabits per second on the stacking port.

Stacking Commands

+ 769 hidden pages

NETGEAR GSM7228PS-100NAS User Manual

ProSafe Managed Switch

Contents

1. Using the Command-Line Interface

Licensing and Command Support

Command Syntax

Command Conventions

Common Parameter Values

Unit/Slot/Port Naming Convention

Using a Command’s “No” Form

Managed Switch Modules

Command Modes

Command Completion and Abbreviation

CLI Error Messages

CLI Line-Editing Conventions

Using CLI Help

Accessing the CLI

2. Stacking Commands

Dedicated Port Stacking

Stacking Commands