Mustek KB4000, KP100, SD100 User Manual

KB4000 / KP100 / SD100

MULTIFUNCTION

SECURITY DEVICE

USER’S MANUAL

Rev. B

MANUFACTURED BY:

AN

MUSTEK CORP.

ISO-9001

AND

ISO-14001

CERTIFIED MANUFACTURER

SOME IMPORTANT NOTES

FCC NOTES

This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions manual, may cause interference to radio communications.
It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of
Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when
operated in a commercial environment. Operation of this equipment in a residential area is likely to
cause interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any person other than
the authorized technicians. The user should consult his/her dealer for the problem happened. Warranty
voids if the user does not follow the instructions in application of this merchandise. The manufacturer
is by no means responsible for any damage or hazard caused by improper application.

The hardware utility program, including instructions for its use, is provided “AS IS” without
warranty of any kind. Mustek Corp. further disclaims all implied warranties including without
limitation any implied warranties of merchantability or of fitness for a particular purpose. the entire risk
arising out of the use or performance of the software and documentation remains with y ou.

ABOUT THIS MANUAL

This manual is written in an attempt with full strength to assist the user to utilize the stand
alone multifunction keyboard KB4000 series together with its derivative upgrade kits for the Posiflex
touch terminal systems. This series of products incorporate several delicately designed POS peripherals
each can be used as an excellent tool to accommodate the required security specially involved in POS
business, kiosk and hospitality operation. This manual covers both operational and technical aspects of
these units.

The manufacturer of the KB4000 series heartily apologizes to the user for reserving the right
to change or to modify this manual without notice due to the rapid and constant progress and
improvement on science and technology. The user may always obtain the most up to date information
through our web site:

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, or
otherwise, without the prior written consent of Mustek Corp. the publisher of this documentation.

TRADE MARKS AND SERVICE MARKS

marks of their respective owners.

http://www.posiflex.com.tw

Copyright Mustek Corp. 2003

©

POSIFLEX is a registered trademark of Mustek Corp..
Other brand and product names are trademarks and registered trademarks and service

.

P/N: 19010900030

GENERAL DESCRIPTION

OVERVIEW

Table below indicates construction of this series of security devices.

KB4000 KP100 SD100

Structure
Programmable keypad
Magnetic stripe reader

Smart card reader

Finger print sensor

iButton reader

Note:

In SD100, the internal control boards for standard USB interface MSR
and smart card reader share same space so they do not exist at the same time.
Choosing a non-USB type MSR can solve the problem but the special support of
MSR connector from the host must be checked for such a choice.

Stand alone Upgrade kit for Jiva (TP) series

Horizontal layout Vertical layout N. A.

Optional
Optional
Optional

N. A.

Optional for one

of the two

Optional for one

of the two

(Note)

OPTIONS

Items underlined below means that this item must be installed by Posiflex
authorized distributor only and never by average user. Items in Italic printing
below means that this item must be installed prior to delivery from the factory.

• Magnetic Stripe Reader (PS2 KB interface for KB4000 and KP100)

∗ ISO 7811 head reader for tracks 1 and 2
∗ ISO 7811 reader head for tracks 2 and 3
∗ ISO 7811 reader head for tracks 1, 2 and 3 + AAMVA + CA DMV
∗ JIS/II reader head

• Magnetic Stripe Reader (USB interface for SD100)

∗ ISO 7811 head reader for tracks 1 and 2
∗ ISO 7811 reader head for tracks 2 and 3
∗ ISO 7811 reader head for tracks 1, 2 and 3 + AAMVA + CA DMV

KB4000 Series User’s Manual

1 - 1

• Magnetic Stripe Reader (MSR interface for SD100)

∗ ISO 7811 head reader for tracks 1 and 2
∗ ISO 7811 reader head for tracks 2 and 3
∗ ISO 7811 reader head for tracks 1, 2 and 3
∗ JIS/II reader head

• Smart card reader

• Finger print sensor

iButton receptor

•

• iButton key

Note: if all devices utilizing a specific interface are omitted from the product,
that interface will not be installed in the product. Ex. For SD100 with only
special interface MSR installed or KP100 or KB4000 containing no finger print
sensor neither smart card reader, there will be no USB interface installed; For
SD100 without the special interface MSR, there will be no MSR connector; For
SD100 without the iButton reader, there will be no 9 pin D connector.

KB4000 Series User’s Manual

1 - 2