The material in this document is the intellectual property of MICRO-STAR
INTERNATIONAL. We take every care in the preparation of this document, but no
guarantee is given as to the correctness of its contents. Our products are under
continual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trade-
marks of NVIDIA Corporation in the United States and/or other countries.
AMD, Athlon™ , Athlon™ XP, Thoroughbred™, and Duron™ are registered trademarks of AMD Corporation.
Intel® and Pentium® are registered trademarks of Intel Corporation.
PS/2 and OS®/2 are registered trademarks of International Business Machines
Corporation.
Windows® 95/98/2000/NT/XP are registered trademarks of Microsoft Corporation.
Netware® is a registered trademark of Novell, Inc.
Award® is a registered trademark of Phoenix Technologies Ltd.
AMI® is a registered trademark of American Megatrends Inc.
Revision History
RevisionRevision HistoryDate
V1.0First release for PCB 1.XMay 2007
Technical Support
If a problem arises with your system and no solution can be obtained from the user’ s
manual, please contact your place of purchase or local distributor. Alternatively,
please try the following help resources for further guidance.
Visit the MSI website for FAQ, technical guide, BIOS updates, driver updates,
and other information: http://global.msi.com.tw/index.php?
4.Lay this equipment on a reliable flat surface before setting it up.
5.The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE OPENINGS.
6.Make sure the voltage of the power source and adjust properly 110/220V before connecting the equipment to the power inlet.
7.Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.
8.Always Unplug the Power Cord before inserting any add-on card or module.
9.All cautions and warnings on the equipment should be noted.
10. Never pour any liquid into the opening that could damage or cause electrical
shock.
11. If any of the following situations arises, get the equipment checked by a service
personnel:
† The power cord or plug is damaged.
† Liquid has penetrated into the equipment.
† The equipment has been exposed to moisture.
† The equipment has not work well or you can not get it work according to
User’s Manual.
† The equipment has dropped and damaged.
† The equipment has obvious sign of breakage.
12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 600 C (1400F), IT MAY DAMAGE THE EQUIPMENT.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
iii
FCC-B Radio Frequency Interference Statement
This equipment has been
tested and found to comply
with the limits for a Class B
digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the measures listed
below.
† Reorient or relocate the receiving antenna.
† Increase the separation between the equipment and receiver.
† Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
† Consult the dealer or an experienced radio/television technician for help.
Notice 1
The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to
comply with the emission limits.
VOIR LA NOTICE D’ INSTALLATION AVANT DE RACCORDER AU RESEAU.
Micro-Star International
MS-7367
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
iv
WEEE (Waste Electrical and Electronic Equipment) Statement
Thank you for choosing the K9AGM3 Series (MS-7367
v1.X) Micro-ATX mainboard. The K9AGM3 Series
mainboards are based on ATi® 690G/ 690V & SB600
chipsets for optimal system efficiency. Designed to fit
the advanced AMD® Athlon 64 X2/ Athlon 64
processor, the K9AGM3 Series deliver a high performance and professional desktop platform solution.
1-1
MS-7367 Mainboard
Mainboard Specifications
Processor Support
- AMD® Athlon64 / Athlon64 X2 processors in AM2 package
- Supports 4 pin CPU Fan Pin-Header with Fan Speed Control
(For the latest information about CPU, please visit http://global.msi.
com.tw/index.php?func=cpuform)
Supported FSB
- 400/ 533/ 800/ 1000 MHz HyperTransport
Chipset
- North Bridge: AMD® 690G/ 690V (optional) chipset
- South Bridge: SB600 chipset
Memory Support
- DDR2 800/667/533 DRAM (240pin/ 1.8V)
- 4 DDR2 DIMMs (8GB Max)
(For more information on compatible components, please visit http:/
/global.msi.com.tw/index.php?func=testreport)
LAN
- Supports 10/100 Fast Ethernet by Realtek 8101E (optional)
- Supports 10/100/1000 Fast Ethernet by Realtek 8111B (optional)
1394 (Optional)
- Transfer rate is up to 400Mbps
- Controlled by VIA VT6308P (optional)
Audio
- Chip integrated by Realtek® ALC888/ ALC883 (optional)
- Flexible 8-channel audio with jack sensing
- Compliant with Azalia 1.0 spec
IDE
- 1 IDE port by SB600
- Supports Ultra DMA 66/100/133 mode
- Supports PIO, Bus Master operation mode
SATA
- 4 SATA ports by SB600
- Supports 4 SATA devices
- Supports storage and data transfers at up to 300MB/s
Floppy
- 1 floppy port
- Supports 1 FDD with 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB
RAID
- SATA1~4 support RAID 0/ 1/ 0+1mode
1-2
Connectors
Back panel
- 1 PS/2 mouse port
- 1 PS/2 keyboard port
- 1 HDMI port (optional for AMD® 690G)
- 1 VGA port
- 1 DVI-D port (optional for AMD® 690G)
- 4 USB 2.0 Ports
- 1 LAN jack
- 6 flexible audio jacks
- 1 1394 port (optional)
On-Board Pinheaders
- 3 USB 2.0 pinheaders
- 1 1394 pinheader (optional)
- 1 TV-out pinheader (optional)
- 1 Front Panel Audio pinheader
- 1 CD-in pinheader
- 1 SPDIF-out pinheader (optional)
- 1 COM port pinheader (optional)
- 1 Chassis Intrusion Switch pinheader
Slots
- 1 PCI Express x16 slot
- 1 PCI Express x 1 slot
- 2 PCI slots
Form Factor
- Micro-ATX (24.4cm X 23.0 cm)
Mounting
- 6 mounting holes
Getting Started
1-3
MS-7367 Mainboard
IDE 1FDD
1
CPUFAN1
JUSB1
JUSB2
BATT
Mainboard Layout
Top : mouse
Bottom:
keyboard
JCOM1(optional)
HDMI Port
Top: VGA Port
Buttom: DVI Port(optional)
Top:1394 (optional)
Bottom: USB ports
LAN
Chip
JPW1
JTV1
(optional)
PCI _EX2
Top: LAN Jack
Bottom: USB ports
T:
Line-In
M:
Line-Out
B:
Mic
T:RS-Out
M:CS-Out
B:SS-Out
RS690G/RS690V
I/O
JCI1
DIMM1
DIMM3
DIMM2
DIMM4
ATX1
1-4
1394
Chip
Audio
codec
PCI _EX16
PCI1
PCI 2
JAUD1
JCD1
SPDOUT1
JBAT1
+
K9AGM3 Series (MS-7367 v1.X)
Micro- ATX Mainboard
SB600
SYSFAN
JFP1JUSB3
SATA4 SATA1
SATA3 SATA2
Packing Checklist
Getting Started
MSI motherboard
Power Cable
User’ s Guide
MSI Driver/Utility CD
Standard Cable for
IDE Devices
SATA Cable
Back IO Shield
* The pictures are for reference only and may vary from the packing contents of the
product you purchased.
1-5
Hardware Setup
Chapter 2
Hardware Setup
This chapter provides you with the information about
hardware setup procedures. While doing the installation,
be careful in holding the components and follow the
installation procedures. For some components, if you
install in the wrong orientation, the components will not
work properly.
Use a grounded wrist strap before handling computer
components. Static electricity may damage the
components.
2-1
MS-7367 Mainboard
Quick Components Guide
JCOM1,
p.2-18
Back Panel
I/O, p.2-9
PCI Express
slots, p.2-20
PCI Slots,
p.2-21
JPW1, p.2-18
JTV1, p.2-16
CPUFAN1, p.2-13
CPU, p.2-3
JBAT1, p.2-19
DDR2 DIMMs, p.2-6
JUSB1~3,
p.2-15
JCI1, p.2-13
FDD1, p.2-11
IDE1, p.2-11
ATX1, p.2-8
SYSFAN,
p.2-13
SATA1~4,
p.2-12
JFP1, p.2-14
2-2
J1394_1, p.2-17
SPDOUT1, p.2-18
JCD1, p.2-13
JAUD1, p.2-14
Hardware Setup
CPU (Central Processing Unit)
The mainboard supports AMD® Athlon64 X2/ Athlon64 processors. The mainboard
uses a CPU socket called Socket AM2 for easy CPU installation. When you are
installing the CPU, make sure the CPU has a heat sink and a cooling fanattached on the top to prevent overheating. If you do not have the heat sink and
cooling fan, contact your dealer to purchase and install them before turning on the
computer.
For the latest information about CPU, please visit http://global.msi.com.tw/index.php?
func=cpuform
Important
Overheating
Overheating will seriously damage the CPU and system. Always make sure
the cooling fan can work properly to protect the CPU from overheating. Make
sure that you apply an even layer of thermal paste (or thermal tape) between
the CPU and the heatsink to enhance heat dissipation.
Replaceing the CPU
While replacing the CPU, always turn off the ATX power supply or unplug the
power supply’s power cord from the grounded outlet first to ensure the safety
of CPU.
2-3
MS-7367 Mainboard
Open the lever
Gold arrow
Gold arrow
Gold arrow
Correct CPU
O
Incorrect CPU
the lever
CPU Installation Procedures for Socket AM2
1.Please turn off the power and
unplug the power cord before
installing the CPU.
Sliding
2.Pull the lever sideways away
from the socket. Make sure to
raise the lever up to a 90-degree angle.
3.Look for the gold arrow on the
CPU. The gold arrow should point
as shown in the picture. The CPU
can only fit in the correct
orientation.Lower the CPU down
onto the socket.
the plate
90 degree
4.If the CPU is correctly installed,
the pins should be completely
embedded into the socket and
can not be seen. Please note
that any violation of the correct
installation procedures may
cause permanent damages to
your mainboard.
5. Press the CPU down firmly into
the socket and close the lever.
As the CPU is likely to move while
the lever is being closed, always close the lever with your
fingers pressing tightly on top of
the CPU to make sure the CPU is
properly and completely embedded into the socket.
2-4
Press down
the CPU
placement
placement
Close
Hardware Setup
Installing AMD Socket AM2 CPU Cooler Set
When you are installing the CPU, make sure the CPU has a heat sink and a
cooling fan attached on the top to prevent overheating. If you do not have the
heat sink and cooling fan, contact your dealer to purchase and install them before
turning on the computer.
Important
1. Read the CPU status in BIOS (Chapter 3).
2. Mainboard photos shown in this section are for demonstration of the CPU/
cooler installation only. The appearance of your mainboard may vary depending on the model you purchase.
1.Position the cooling set onto the retention mechanism.
Hook one end of the clip to hook
first.
3.Fasten down the lever.
2. Then press down the other end of
the clip to fasten the cooling set on
the top of the retention mechanism.
Locate the Fix Lever and lift up it .
Fixed Lever
4.Attach the CPU Fan cable to the CPU
fan connector on the mainboard.
2-5
MS-7367 Mainboard
1
2
3
Installed
Memory
These DIMM slots are used for installing memory modules.
For more information on compatible components, please visit http://global.msi.com.
tw/index.php?func=testreport
DDR2
240-pin, 1.8V
64x2=128 pin56x2=112 pin
Dual-Channel Memory Population Rules
In Dual-Channel mode, the memory modules can transmit and receive data with two
data bus lines simultaneously. Enabling Dual-Channel mode can enhance the system
performance. Please refer to the following illustrations for population rules under
Dual-Channel mode.
DIMM1
DIMM3
DIMM2
DIMM4
DIMM1
DIMM3
DIMM2
DIMM4
DIMM1
DIMM3
DIMM2
DIMM4
Empty
2-6
Hardware Setup
Installing Memory Modules
1. The memory module has only one notch on the center and will only fit in the right
orientation.
2. Insert the memory module vertically into the DIMM slot. Then push it in until the
golden finger on the memory module is deeply inserted in the DIMM slot.
Important
You can barely see the golden finger if the memory module is properly inserted
in the DIMM slot.
3. The plastic clip at each side of the DIMM slot will automatically close.
Volt
Notch
Important
-DDR2 memory modules are not interchangeable with DDR and the DDR2
standard is not backwards compatible. You should always install DDR2
memory modules in the DDR2 DIMM slots.
-In Dual-Channel mode, make sure that you install memory modules of the
same type and density in different channel DIMM slots.
-To enable successful system boot-up, always insert the memory modules
into the DIMM1 first.
- Due to the chipset resource deployment, the system density will only be
detected up to 7+GB (not full 8GB) when each DIMM is installed with a 2GB
memory module.
2-7
MS-7367 Mainboard
Power Supply
ATX 24-Pin Power Connector: ATX1
This connector allows you to connect an ATX 24-pin power supply.
To connect the ATX 24-pin power supply, make sure the plug of the
power supply is inserted in the proper orientation and the pins are
aligned. Then push down the power supply firmly into the connector.
You may use the 20-pin ATX power supply as you like. If you’d like
to use the 20-pin ATX power supply, please plug your power supply along with pin 1 & pin 13 (refer to the image at the right hand).
There is also a foolproof design on pin 11, 12, 23 & 24 to avoid
wrong installation.
This power connector JPW1 is used to provide power to the CPU.
JPW1
4
Pin Definition
2
13
PINSIGNAL
1GND
2GND
312V
412V
Important
1. Maker sure that all the connectors are connected to proper ATX power supplies to ensure stable operation of the mainboard.
2. Power supply of 350 watts (and above) is highly recommended for system
stability.
2-8
Back Panel
Mouse
VGA
(optional)
1394
Hardware Setup
Line-In
LAN
RS-Out
Keyboard
HDMI
(optional)
DVI-D
(optional)
Line-Out
USB Ports
Mic
CS-Out
SS-Out
Mouse/Keyboard
The standard PS/2® mouse/keyboard DIN connector is for a PS/2® mouse/keyboard.
HDMI Port (optional)
The High-Definition Multimedia Interface (HDMI) is an all-digital audio/video interface
capable of transmitting uncompressed streams. HDMI supports all TV format, including standard, enhanced, or high-definition video, plus multi-channel digital audio on a
single cable.
VGA Port
The DB15-pin female connector is provided for monitor.
DVI-D Port (optional)
The DVI (Digital Visual Interface-Digital) connector allows you to connect a LCD
monitor. It provides a high-speed digital interconnection between the computer and
its display device. To connect an LCD monitor, simply plug your monitor cable into the
DVI connector, and make sure that the other end of the cable is properly connected
to your monitor (refer to your monitor manual for more information.)
IEEE 1394 Port (optional)
The 1394 port on the back panel provides connection to 1394 devices.
USB Port
The USB (Universal Serial Bus) port is for attaching USB devices such as keyboard,
mouse, or other USB-compatible devices.
2-9
MS-7367 Mainboard
LAN
The standard RJ-45 LAN jack is for connection to the Local Area Network (LAN).
Link IndicatorActivity Indicator
You can connect a network cable to it.
LED ColorLED StateCondition
OffLAN link is not established.
Left OrangeOn (steady state)LAN link is established.
GreenOff10 Mbit/sec data rate is selected.
RightOn100 Mbit/sec data rate is selected.
OrangeOn1000 Mbit/sec data rate is selected.
On (brighter & pulsing)The computer is communicating with another computer on the LAN.
Audio Ports
These audio connectors are used for audio devices. You can differentiate the color
of the audio jacks for different audio sound effects.
Line-In (Blue) - Line In, is used for external CD player, tapeplayer or other
audio devices.
Line-Out (Green) - Line Out, is a connector for speakers or headphones.
Mic (Pink) - Mic, is a connector for microphones.
RS-Out (Black) - Rear-Surround Out in 4/ 5.1/ 7.1 channel mode.
CS-Out (Orange) - Center/ Subwoofer Out in 5.1/ 7.1 channel mode.
SS-Out (Gray) - Side-Surround Out 7.1 channel mode.
2-10
Hardware Setup
Connectors
Floppy Disk Drive Connector: FDD1
This connector supports 360KB, 720KB, 1.2MB, 1.44MB or 2.88MB floppy disk drive.
FDD1
IDE Connector: IDE1
This connector supports IDE hard disk drives, optical disk drives and other IDE devices.
IDE1
Important
If you install two IDE devices on the same cable, you must configure the
drives separately to master / slave mode by setting jumpers. Refer to IDE
device’s documentation supplied by the vendors for jumper setting
instructions.
2-11
MS-7367 Mainboard
Serial ATA Connector: SATA1/ SATA2/ SATA3/ SATA4
This connector is a high-speed Serial ATA interface port. Each connector can connect to one Serial ATA device.
SATA1SATA2
SATA4SATA3
Important
Please do not fold the Serial ATA cable into 90-degree angle. Otherwise,
data loss may occur during transmission.
2-12
Hardware Setup
Fan Power Connectors: CPUFAN1, SYSFAN
The fan power connectors support system cooling fan with +12V. When connecting
the wire to the connectors, always note that the red wire is the positive and should
be connected to the +12V; the black wire is Ground and should be connected to GND.
If the mainboard has a System Hardware Monitor chipset on-board, you must use a
specially designed fan with speed sensor to take advantage of the CPU fan control.
GND
+12V
SENS OR
Control
GNDSENSOR
+12V
CPUFAN1
SYSFAN
Important
1.Please refer to the recommended CPU fans at processor’s official website
or consult the vendors for proper CPU cooling fan.
2.CPUFAN1 supports fan control. You can install Dual Core Center utility
that will automatically control the CPU fan speed according to the actual
CPU temperature.
3. Fan/heatsink with 3 or 4 pins are both available for CPUFAN1.
Chassis Intrusion Switch Connector: JCI1
This connector connects to the chassis intrusion switch cable. If the chassis is
opened, the chassis intrusion mechanism will be activated. The system will record
this status and show a warning message on the screen. To clear the warning, you
must enter the BIOS utility and clear the record.
2
GND
CINTRU
1
JCI1
CD-In Connector: JCD1
This connector is provided for external audio input..
R
L
GND
JCD1
2-13
MS-7367 Mainboard
Front Panel Audio Connector: JAUD1
This connector allows you to connect the front panel audio and is compliant with
Intel® Front Panel I/O Connectivity Design Guide.
2
1
10
9
JAUD1
Pin Definition
PINSIGNALDESCRIPTION
1AUD_MICFront panel microphone input signal
2AUD_GNDGround used by analog audio circuits
3AUD_MIC_BIASMicrophone power
4AUD_VCCFiltered +5V used by analog audio circuits
5AUD_FPOUT_RRight channel audio signal to front panel
6AUD_RET_RRight channel audio signal return from front panel
7HP_ONReserved for future use to control headphone amplifier
8KEYNo pin
9AUD_FPOUT_LLeft channel audio signal to front panel
10AUD_RET_LLeft channel audio signal return from front panel
Front Panel Connectors: JFP1
These connectors are for electrical connection to the front panel switches and LEDs.
The JFP1 is compliant with Intel® Front Panel I/O Connectivity Design Guide.
Power
Power
LED
Switch
Reset
Switch
10
9
JFP1
2
1
HDD
LED
2-14
Pin Definition
PINSIGNALDESCRIPTION
1HD_LED +Hard disk LED pull-up
2FP PWR/SLPMSG LED pull-up
3HD_LED -Hard disk active LED
4FP PWR/SLPMSG LED pull-up
5RST_SW -Reset Switch low reference pull-down to GND
6PWR_SW +Power Switch high reference pull-up
7RST_SW +Reset Switch high reference pull-up
8PWR_SW -Power Switch low reference pull-down to GND
9RSVD_DNUReserved. Do not use.
Hardware Setup
Front USB Connector: JUSB1 / JUSB2 / JUSB3
This connector, compliant with Intel® I/O Connectivity Design Guide, is ideal for connecting high-speed USB interface peripherals such as USB HDD, digital cameras,
MP3 players, printers, modems and the like.
Pin Definition
PIN SIGNALPINSIGNAL
JUSB1/2/3
2
1
10
9
1VCC2VCC
3USB0-4USB15USB0+6USB1+
7GND8GND
9Key (no pin)10USBOC
USB 2.0 Bracket
(Optional)
Important
Note that the pins of VCC and GND must be connected correctly to avoid
possible damage.
2-15
Loading...
+ 66 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.