MSD 8725 Installation

Page 1
Electronic Governor
PN 8725
ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product will help if there is ever a warranty issue with your product and helps the MSD R&D team create new products that you ask for! Go to www.msdperformance.com/registration.
Parts Included:
1 - Electronic Governor 3 - RPM Limit Modules (3,600, 3,800 and 4,000 RPM)
with standard systems only.
MOUNTING THE ELECTRONIC GOVERNOR
The Electronic Governor may be mounted in any location in the engine compartment except on the engine or near the exhaust manifold. Excessive heat at these locations could damage the unit. When selecting a mounting location, make sure that the cable assembly will reach to the locations shown in Figure 1, 2, 3, or 4. Mark locations of the mounting holes at the corners of the unit and drill 1/8" holes at these locations. Mount the unit using the self tapping screws provided in the parts kit.
2 - Wire Splice Devices 4 - Self Tapping Screws
PROGRAMMING FOR 4, 6 OR 8 CYLINDER OPERATIONS
The short Red and Blue wire loops coming out of the Engine Governor are used for programming the unit for 4, 6, or 8 cylinder operation. Modify the loops as described for the number of cylinders that your engine has. Remember to tape any cut wires to prevent shorting.
8-Cylinder: Do not cut any loops. 6-Cylinder: Cut only the Red loop. 4-Cylinder: Cut both the Red and Blue loops.
SETTING THE RPM LIMIT
The RPM that the limiting action occurs at is easily adjusted with plug-in modules. Modules for 3,600, 3,800 and 4,000 RPM are included with this unit. Choose one and plug it into the module receptacle. If other RPM Modules are desired, see the list of RPM Module Kits on page 4.*
CONNECTING THE ELECTRONIC GOVERNOR
Figures 1, 2, 3 and 4 show the hookup for most vehicles. Select the proper diagram to connect the Engine Governor to your particular make of vehicle.
M S D   •   W W W . M S D P E RF O R M A N C E . C O M   •   ( 9 1 5 )   8 5 7 - 5 2 0 0   •   F A X   ( 9 1 5 )   8 57 - 3 3 4 4
Page 2
2 INSTALLATION INSTRUCTIONS
RPM MODULE
ELECTRONIC GOVERNOR
PN 8725
MAKE SURE THAT THE RED WIRE IS CONNECTED TO THE IGNITION KEY SIDE OF THE BALLAST RESISTOR.
Figure 1 Hookup for Domestic and Foreign Vehicles using a Threaded Stud Coil.
BLACK
IGNITION
KEY
RED
GREEN
ENGINE
GROUND
FROM BATTERY (+)
COIL
FROM POINTS OR
AMPLIFIER
BALLAST
IF USED
(+)
(-)
ELECTRONIC GOVERNOR
PN 8725
RPM MODULE
GREEN
BLACK
BROWN
RED
ENGINE
GROUND
PINK
BLACK
Figure 2 Hookup for GM Vehicles with the Unitized HEI system.
M S D   •   W W W . M S D P E RF O R M A N C E . C O M   •   ( 9 1 5 )   8 5 7 - 5 2 0 0   •   F A X   ( 9 1 5 )   8 57 - 3 3 4 4
Page 3
INSTALLATION INSTRUCTIONS 3
ELECTRONIC GOVERNOR
PN 8725
RPM MODULE
RED
GREEN
COIL
BLACK
ENGINE
GROUND
FORD
IGNITION MODULE
RED
MAKE SURE THAT THE GREEN WIRE IS HOOKED TO THE SIDE OF THE COIL WHERE THE WORD "TACH" IS MOLDED INTO THE COIL CONNECTOR. THIS IS THE NEGATIVE (-) SIDE OF THE COIL.
ELECTRONIC GOVERNOR
PN 8725
Figure 3 Hookup for Ford vehicles with Electronic Ignition.
DARK GREEN/
YELLOW
LT. GREEN
RPM MODULE
GREEN
RED
BLACK
ENGINE
GROUND
RED/
TFI COIL
(+)
(-)
Figure 4 Hookup for Ford Vehicles with the Ford TFI system.
M S D   •   W W W . M S D P E RF O R M A N C E . C O M   •   ( 9 1 5 )   8 5 7 - 5 2 0 0   •   F A X   ( 9 1 5 )   8 57 - 3 3 4 4
Page 4
TECH NOTES
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
Service
In case of malfunction, this MSD component will be repaired free of charge according to the terms of the warranty.
When returning MSD components for warranty service, Proof of Purchase must be supplied for verification. After the warranty period has expired, repair service is based on a minimum and maximum fee.
All returns must have a Return Material Authorization (RMA) number issued to them before
being returned. To obtain an RMA number please contact MSD Customer Service at 1 (888) MSD-7859 or visit our website at www.msdperformance.com/rma to automatically obtain a number and shipping information.
When returning the unit for repair, leave all wires at the length in which you have them installed. Be sure to include a detailed account of any problems experienced, and what components and accessories are installed on the vehicle. The repaired unit will be returned as soon as possible using Ground shipping methods (ground shipping is covered by warranty). For more information, call MSD at (915) 855-7123. MSD technicians are available from 7:00 a.m. to 5:00 p.m. Monday - Friday (mountain time).
Limited Warranty
M
SD warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date of the original purchase. This warranty is void for any products purchased through auction websites. If found to be defective as mentioned above, it will be repaired or replaced at the option of MSD. Any item that is covered under this warranty will be returned free of charge using Ground shipping methods. This shall constitute the sole remedy of the purchaser and the sole liability of MSD. To the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied, including any implied warranty of merchantability or fitness. In no event shall MSD or its suppliers be liable for special or consequential damages. *Intended normal use means that this item is being used as was originally intended and for the original application as sold by MSD. Any modifications to this item or if it is used on an application other than what MSD markets the product, the warranty will be void. It is the sole responsibility of the customer to determine that this item will work for the application they are intending. MSD will accept no liability for custom applications.
M S D   •   W W W . M S D P E RF O R M A N C E . C O M   •   ( 9 1 5 )   8 5 7 - 5 2 0 0   •   F A X   ( 9 1 5 )   8 57 - 3 3 4 4
© 2012 Autotr onic Cont rols Corp oration
FRM28466 Revised 02/12 Printed in U.S.A.
Loading...