Moultrie LX-30IR User Manual

MFH-DGS-LX30IR

Table of Contents

Introduction
Important Care & Caution Information
Important Battery Information
Moultrie Limited Warranty……………………………………………… 2

Quick Start Guide……………………………………………………..... 3

Default/Easy Start

Specifications………………………………………………………….... 4

Product Overview……………………………………………………..... 5

Definitions……………………………………………………………….. 6

Camera Setup…………………………………………………………... 7 & 8

Programming Camera………………………………………………….. 9 & 10

Capture Modes
Memory & Storage……………………………………………………... 11

Downloading & Viewing Images
Warnings & Regulations……………………………………………….. 12

To connect the camera to a PC computer, press and hold the (On/Off) button until LCD turns
on, slide the (Mode) switch to (Setup). Connect the USB cord (

not included) between the USB

out port and the PC computer. The computer will recognize the camera as a removable
drive. Copy the images and videos from the camera onto your PC for further editing or
printing. When the USB cable is disconnected, the camera will go back to (Setup) mode.

Connecting to Computer

FCC Statements
Note: changes and modifications not expressly approved by the party responsible could void the user’s authority
to operate this device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

NOTE: This device complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This product may not comply with California Proposition 65 standards, known to the state of California to cause
birth defects or other reproductive harm.

Warnings & Regulations

Printed in China

03/12

RECYCLED

RECYCLABLE

Moultrie Products, LLC
MFH-DGS-LX30IR

12

Introduction

Thank you for your purchase of Moultrie LX-30IR
Infrared Surveillance Camera.

Your LX-30IR camera is a compact high performance digital surveillance camera that uses
infrared detection. Your game camera uses an infrared detector to sense heat changes in
the surrounding environment. When movement from a heat source such as people or
animals is detected, the camera will trigger and take a picture or video clip. It is a rugged
camera that is an ideal tool for spotting game or general surveillance.

Please enjoy this quality product and follow these sample instructions, to keep your camera
working properly and pay attention to the following care and caution Information:

Important Care & Caution Information

• Do not attempt to open the camera for any unauthorized service. This will void the
warranty.

• Keep the memory card out of the reach of children in order to avoid any risk of it being
swallowed.

• When the camera is not in use, please remove the memory card and batteries.

• Please don't subject this camera to a strong shock or pressure. It can cause a loss in the

weather resistant performance.

• Do not touch the lens with fingers. Use a soft lens cloth to clean lens.

Important Battery Information

• Only use Alkaline batteries. We recommend the use of

Duracell

®

or Energizer

®

batteries.

• Do not mix old and new batteries. Always replace ALL the batteries at the same time.

• When the camera is not in use, please remove the batteries.

Moultrie Limited Warranty

This product has been thoroughly tested and inspected before shipment. It is guaranteed from
defects in material and workmanship from the date of purchase for 1 year. Under this limited
guarantee we agree to replace or repair free of charge any part or parts which have been found
to be defective in original material or workmanship. Should you require in-warranty service, call
our Customer Service Department. If your problem cannot be addressed over the telephone, we
may need you to send us your defective product plus proof of purchase.

IMPORTANT:

You must activate your warranty online at: www.moultriefeeders.com/warranty to be
covered.

Our Service Department will gladly answer any questions you may have.
Call: Toll Free: [phone]
Address: 150 Industrial Road • Alabaster, AL 35007
Hours: Monday - Friday 8:00am to 5:00pm CST
Register Online: www.moultriefeeders.com/warranty

Customer Service Contact Information

2

Memory & Storage

Downloading & Viewing Images

Your camera supports external SD memory card ONLY and will accept up to a 32GB card.
Using large memory cards can slow the camera response. If the camera cannot capture any
photo or video without external memory, please insert a SD memory card to operate
camera. Estimates are based on the most common types of memory cards that can be
purchased at electronic stores, office
supply stores, or online. Estimates
may vary based on camera settings
or environmental conditions.

Memory Full

When the LCD shows (FULL), it
means that the memory is full. The
camera will shut off automatically to
save battery life. Please insert an
empty SD memory card for
memory space.

Important: Always turn the unit
off when inserting or removing an
SD memory card to avoid damage
and ensure that the camera
properly updates the memory
information.

There are a number of ways for you download and view the pictures, videos in the field or
at another location.

In the Field

You can download the pictures, videos,
and time lapse pictures with the aid of
external devices. To download in the field
use a devise that supports SD cards or
a mini USB jack.

Removing

To remove the SD Memory Card open
the camera cover and push gently on
the SD card and it will pop out slightly
allowing you to remove it. Load the
SD card into the player or card reader
to view or move stored images
to another location.

Important: Make sure that the camera
is in the OFF position before removing
SD memory card.

Actual capacity will vary based on image properties.

See the full line of Moultrie camera
accessories at www.moultriefeeders.com

Auto Mode

Video Mode

SD Card: 2 GB 16 GB

HIGH 2560 x 1920 534 5,353

LOW 640 x 480 8,000 64,000

SD Card: 2 GB 16 GB

AVI 640 x 480 204 1,632

11

Capture Modes

Setting Camera ID

Press the (Select) button to select an
Identity for your camera. Choose between
nine (1 - 9) different numbers so the
locations can be marked every time the
camera is triggered. After the selections
have been made, press the (Select) button
and the LCD will display the time again. This
concludes the LCD readout display settings.

Setting Time Delay

To set the time delay, slide the (Delay) switch
to the desired time. There are 4 time delay
settings, 1 min, 5 mins, 10 mins and 30 mins.

Setting Image Quality

Slide the (Resolution) switch to the desired
setting. Choose one of 3 settings. High:
2560x1920 or Low: 640x480 for still images.
Choose (VID) for the video setting.

Sleep Mode

After all your settings have been made, slide the
(Mode) switch to (Auto) and close the cover.

Note: If there is no activity within 2 minutes,
the camera will enter sleep mode to conserve
battery life. The camera will then power up and
become active when motion is detected.

Photo Mode

To operate the camera in (Photo) mode, slide
the (Resolution) button to the (HI) or (LO) position.
Slide the (Mode) switch to (AUTO) position. The
LCD display will will count down for 10 seconds.
After the LCD goes off, the camera is ready for
capturing photo.

Video Mode

To operate the camera in (Video) mode, slide the
(Resolution) button to the (VID) position. Slide the
(Mode) switch to (AUTO) position. The LCD
display will count down for 10 seconds. After the
LCD goes off, the camera is ready for capturing
video. (10 second video clips at (30 FPS) frames
per second).

10

Use the steps below as a guide to quickly set up your camera so it will function
using the factory default settings.

STEP 1

Open camera cover. Install 4 C-Cell
Alkaline batteries. Make sure that
the polarities on the batteries match
the polarities indicated in the battery
chamber. Recommended for use:
Duracell® or Energizer

®

batteries.

STEP 2

Insert SD Memory Card until you hear
an audible click. Camera will not
operate without SD Card. Slide the
(Mode) Switch to Setup. Turn the
power ON. Press and hold (On/Off)
button until LCD activates. Set the
time and date with navigation
buttons, (Up/Down - Select/Enter).

STEP 3

Mount Camera in desired Location
using a mounting strap. Switch
camera to IR Aim.

Aim camera
using motion detection to
determine target area. Walk in
front of the camera at the desired
distance and the camera LED will
flash showing the covered area.

STEP 4

Set the (Delay) and (Resolution).
Slide the (Mode) switch to (Auto).
The camera will start count down.
Close cover and secure.

The
camera will operate using
(Default) settings. You may also
customize the settings if required.

Quick Start Guide

3

System Requirements

OS: Microsoft® Windows® XP with Service Pack 2
(Service Pack 3 recommended); Windows Vista® Home Premium,
Business, Ultimate, or Enterprise with Service Pack 1; or Windows 7

Hard disk space: 100MB or above
CPU: Intel® Pentium® 4 or AMD Athlon® 64 processor or above
Memory: 1GB of RAM

Operational Mode Auto - Game Detect / Video - 10 sec. AVI clips
Resolution 5.0 MP
Still Resolutions JPEG - Low 640x480, High 2560x1920
Video Resolutions AVI - 640x480 at 30FPS
Image Format USB OUT or SD Card
Response Time 1.2/1.5 seconds
Sensor 2.0 MP
Housing Weather-resistant and lockable
Display Liquid Crystal Display (LCD)
LCD Status Display Picture Count
Status LED Camera, or IR activity
SD Memory Card Up to 32 GB SD card (not included)
Format JPEG - Still pictures, AVI - Video: 10 second clips
USB Output Requires PC / MS Windows XP/Vista/7
Picture Delay Variable 1, 5, 10, 30 minutes
Standby Time 170 days
Run Time 90 days
Focus 5' - Infinity
Infrared Sensor Passive
Infrared Range Up to 40”
Flash Type 12 LED's 850nm
Flash Range 5' - 40'

Note When batteries become weak, the flash power is reduced to increase run time.

Upgradeable Software Yes
Easy Read Bar Camera ID / Date / Time
Power Supply 4 C-Cell Alkaline batteries (not included)
External Power port 12V
Size 7" x 5" x 2.5"

Factory Settings

PHOTO QUALITY: HIGH 2560 x 1920 FILE COUNT: 0001

TIME/DATE:

AM

12:00 2011/1/01

CAMERA ID: 1

Default/Easy Start

Specifications

4

Setup and Programming

Navigating Different Settings

During the (Setup) mode, you can program the
camera for different settings. The (Enter) button will
start the programming process when the selection
flashes. The (Up/Down) buttons will move from one
value to the next. The (Enter) button will then lock in
any selections. Then press the (Select) button again
to move to the next setting.

Turning Power ON/OFF

Open the camera cover. Turn the (Mode) switch to
the (Setup) position. Press and hold the (On/Off)
button until the time appears on the LCD display. If
you want to turn the unit off, press the (On/Off)
button once, the LCD shows “OFF” and then
goes off.

Note: If there is no activity for 2 minutes the
camera will shut off automatically to save
battery life.

Setting Time and Date

While the camera is in the (Setup) mode,
the LCD Display will show the time. Press
the (Enter) button and the selection will
flash. Use the (Up/Down) buttons to move
from one value to the next. Press the
(Enter) button to make the selection. Press
the (Select) button to move to the next
selection. Repeat the process to set the
year, month and day.

Reset Picture Count

After the camera’s time and date have been
set, you can reset the picture count on the
camera. Press the (Select) button until
(Clr) shows in the LCD display. Press
(Enter) button and use the (Up/Down)
buttons to choose between Yes or No.
(Yes) will reset file number to start
from 0001.

9

5

Moultrie Accessories

Product Overview

1 Security Lock Hole
2 Cover Latch
3 Mounting Strap Slot
4 Front Cover
5 On / Off Button
6 LCD Display
7 Infrared Sensor
8 Lens
9 LED Infrared Flash
10 Red Status Indicator
11 Green Battery Indicator
12 Up / Down Buttons
13 Select / Enter Buttons

14 Battery Chamber
15 Resolution Switch
16 Delay Switch
17 Mode Switch
18 Tree Mount Socket
19 SD Card Slot

3

4

5 6 7 8 9 10 11

19 20

2

1

13

12

14

18

17 1516

21 22 23 24

20 USB Out Port
21 Cord Strain Relief
22 12V DC Power Panel Plug
23 Tripod Mount Socket
24 Water-resistant Seal

5

8

Aiming Camera

After the camera has been mounted, open the
cover and slide the (Mode) Switch to (IR Aim).
Close Cover. Stand in front of the camera.
The (Status) LED will flash red when it
detects movement. Use this process to guide
your camera to cover the desired target area.

Using a Tripod

Set the Tripod facing up or down the trail
approximately 3 ft. high. Screw the camera
onto the Tripod head in a clockwise direction.
Lock the tripod into place.

Hint: Place something heavy around the legs
of the tripod to help hold the tripod in place.
Camouflage the tripod with local brush.

Note: Make sure that the brush does not
interfere with the camera.

Using a Tree Mount

The camera can also be mounted directly to
a tree using a mounting bracket that attaches
directly to a tree or pole. Strap the tree mount
to the tree and secure, then attach the
camera to the tree mount using the tree
mount socket located on the back of
the camera.

Using Power Panel

Place near the tree where the camera is
mounted. Place for best exposure to sun. To
attach to a tripod secure the power panel to
the tripod angled upward for best exposure.
Plug the power panel to the 12V Power Panel
Plug. This will extend the life of your camera
in the field.

Note: Leave batteries in the camera installed
during use.

Definitions

5 ON/OFF Button

Press and hold the (ON/OFF) button down until the LCD display activates. To turn the camera
off, Press and hold the (ON/OFF) button down until the LCD display deactivates.

6 LCD Display

Shows important operational information such as time, date, picture count, and camera ID.

7 Infrared Sensor

Detects motion and tells the camera when to activate using the preferences setup by the user.

8 LED Infrared Flash

In low light situations the LED flash will activate using infrared technology.

10 Sta

tus LED Indicator

The LED Indicator will turn red when motion or heat is detected while using the IR Aim function.

11 Battery LED Indicator

Turns green to Indicate batteries are low and need to be replaced.

12 Up / Down Buttons

The up or down buttons are used to move up or down to change the values for each setting.

13 Select / Enter Button

Used to select the settings for the camera.

14 Battery Chamber

Used to store batteries. Note: make sure that your (+ or _) polarities match the polar

ities indicated

inside the battery chamber.

15 Resolution Switch

Depending on the position of the switch, there will be 1 video option: (VID) and 2 still image resolutions:
(HI and LO).

16 Delay Switch
Depending on the position of the switch, there are 4 time delay: 1 min, 5mins, 10mins and 30mins.
17 Mode Switch

IR Aim Mode
Infrared detection is used to assist in aiming the camera at your desired target area. Note: the camera
must be on to use the IR Aim feature.

Setup Mode

Customize the cameras settings by slidin

g the (Mode) switch to the (Setup) position. Follow the prompts

on the LCD display.

Auto Mode

The camera will be operational and capture images or videos when the (Mode) switch is in the
(Auto) position. In the (Auto) mode the LCD display will show the time and then will count down for
10 seconds. The LCD goes off and the camera will enter (Standby) for capturing images or videos.

18 Tree Mount Socket

Is used to mount your camera to a tree or pole using tree mount tripod accessory.
Sold separately, vis

it us at www.moultriefeeders.com for more information.

19 SD Card Slot

Will accept SD cards up to 32 GB. To remove SD card gently push the card inward and let go, the card
should pop out enough to remove.

20 USB Out Port

Is used to connect your camera to a computer or external device to download, view, or delete pictures
and videos off the camera.

22 12V DC Power Panel Plug

Used to connect an external power source. Accepts Moultrie accessories. Visit us at
www.moultriefeeders.com for more information.

23 Tripod S

ocket

Is used to mount your camera to a tripod when necessary. Sold separately, visit us at
www.moultriefeeders.com for more information.
24 Water-Resistant Seal
Helps keep moisture out of the unit during wet conditions.

6

Camera Setup

Battery Installation

Open the camera cover and install 4 C-Cell
Alkaline batteries. Make sure that the
(+ and _) polarities match the polarities
indicated inside the battery chamber.

Note: Anytime you load or unload batteries,
make sure that the camera is OFF. If using
12V DC Power Panel Plug, do not remove
internal batteries.

Insert SD Card

You will need to open the front cover to
insert a SD memory card. You can insert a
SD Card up to 32 GB. Insert the SD card in
the direction indicated on the card, until you
hear an audible click.

Note: Camera will not operate without
an SD memory card installed.

Power ON

Slide the (Mode) Switch to the (Setup)
position. Press and hold the (ON/OFF)
Button until the time appears on the LCD
Display. The camera will power up.

Mounting with a Strap

Close cover and place camera on a tree or
pole approximately 3 ft. high. Thread
the mounting strap through the mounting
strap slots on the back of the camera
and secure.

Hint: If you are mounting camera to cover a
trail face the camera down the trail tilted at
a slight downward angle.

Face the camera North or South to avoid
over exposure from the sun.

Clear brush away from camera front to
avoid false triggers from the wind.

NO

Trail

YES

Trail

7