Moultrie DIGITAL GAME CAMERA 100 User Manual

OPERATIONS • INFRARED SENSOR

DETECTION

The game camera's infrared sensor will trigger camera when
motion is detected infront of the camera infrared sensor.

AIMING INFRARED SENSOR

If your Game camera is not equipped with a laser aiming
device you can use the systems (INFRARED SENSOR) to
aim your camera. Walk in front of the camera and the Status
Light will flash when you enter the field of view. This
indicates Infrared activation.

6 MEMORY • CAPACITY & STORAGE

Your digital game camera has two
types of memory capacity.

1)Internal memory.

2)Optional SD memory card.

NOTE: Optional SD memory card
will override internal memory.
Maximum card size is 256 MB.

MEMORY CHART

Image capacity is based on average use and will vary.

Image Internal Memory

Standard 640 x 480 = 100 pics.
High Res 1280 x 1024 = 24 pics
Video Clips 10 frames per sec. = 9

Image Optional 256 MB Card

Standard 640 x 480 = 2,320 pics.
High Res 1280 x 1024 = 608 pics
Video Clips 10 frames per sec. = 288

IMPORTANT: Always turn unit off when inserting or
removing a memory card to avoid damage and ensure
that the camera properly updates the memory
information.

SD MEMORY CARD NOT INSTALLED: When the camera is turned

on and an SD memory card is not present, pictures are automatically
stored in the on-board camera memory. The stored images may only
be viewed on a computer or TV connected to the unit.

INSERTING AN SD MEMORY CARD: When an SD memory card is
inserted, any pictures stored in the camera on-board memory
become inaccessible, but are not lost. The user can access these
pictures via the camera USB port when the SD memory card is not
installed.

NOTE: If you get a message (CHECK MEMORY CARD) Your card
may be locked, full or defective and will not work.



OPERATIONS • IMAGE VIEWING

TV IMAGE VIEWING

Move the Switch to (ON). Connect unit TV OUT to a VIDEO
IN jack on your TV. Use the (CHANGE) buttons to scroll
through recorded images. Video cable included. TV OUT
works only in (SETUP) mode. All pictures
on memory card can be printed or edited
directly from the card.

Use optional card reader to
read images on card.

COMPUTER IMAGE VIEWING (Setup Mode Only)

Move the Switch to (ON). Connect unit USB OUT to a USB
jack on the computer.Double click "My Computer"
on the desktop and browse
"removable disk". USB works
only in SETUP mode. All your
images will be stored inside.
Images can be downloaded to
your hard drive. The first image
in the video mode is still and
contains time and date
information for the video clip.

NOTE: PC requires

windows 2000/ME/XP.

7 CAMERA • DESCRIPTION

Viewfinder

Shutter Button

(handheld)

Status Light

Infrared

Sensor

Mounting
Strap Lug

Power ON/OFF

(AIM optional)

Select Button (setup)

Status Light

Mode Button

Battery Hold Down Clips

Battery Compartment

Weather-Resistant Seal

Control Box Latch

Battery Connector

Pressure
Equalization Hole

( - black )

Light Sensor
Camera Lens

LCD Status
Display

Lockable
Latch

Weather
Resistant
Housing

Laser (optional)

Electronic Flash

TV Out
USB Out

SD Memory
Card Slot

Change Buttons
UP Down

Battery Connector
( + red )

8 CAMERA • SPECIFICATIONS

Operational Mode Auto or Handheld
Housing Weather-resistant and lockable
Display Liquid Crystal Display (LCD)
LCD Status Display Operating Mode Pictures taken  

 Pictures left  Events
 Battery Strength Camera status 

Status LED Camera, Flash or IR activity
Sensor 1.3 Megapixel
Built-in Memory Stores pictures or video
Memory Card Up to 256 MB SD card (optional)
Format  JPEG - Still pictures, AVI - Video clips
Image Output  USB OUT, TV OUT, SD Card
USB Output  Requires PC / Windows 2000/ME/XP.
Picture Delay  Variable 1 Minute - 60 Minutes
Sequential Delay  15 Seconds between still pictures
Lens  Multi element, 10.2mm, F:2.8
Field of View  42°
Focus  4' - Infinity
Infrared Sensor  Passive
Infrared Distance  32'
Infrared Width  22°
Flash  On, Auto or Off ( Security)
Flash Range  30'
Flash Cycle  15 Seconds
Power Supply  6 Volt Lantern Battery or equivalent
Duty Cycle 20 day average with 6 volt/6 ah battery
Power Connection  Alligator clips, red = (+) / black = (-)
Battery Hold Downs Holds battery in place
Clock Battery  3 Volt battery powers LCD Time/Date
Laser Aim (optional)  Class 2
Size  7" X 10.25" X 3.5"
Accessories  Rechargeable battery, Memory Cards.

WARRANTY

This product has been thoroughly tested and inspected before shipment. It is
guaranteed from defects in material and workmanship from the date of
purchase for 1 year. Under this limited guarantee we agree to replace or
repair free of charge any part or parts which have been found to be defective
in original material or workmanship. Should you require in-warranty service,
call our Customer Service Department. If your problem cannot be addressed
over the telephone, we may need you to send us your defective product plus
proof of purchase.

IMPORTANT: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Moultrie Feeders

150 Industrial Rd.

Moultrie Customer Service
[phone] or [phone]
www.moultriefeeders.com

Alabaster, AL 35007

Printed in China

(0905)

DIGITAL GAME CAMERA 100

USER MANUAL

Please take a few minutes
to read and understand these
instructions before using.

1

QUICK START

EASY STEPSEASY STEPS

33

A

B

C

and you are ready to go!

Load Battery and Turn

On Power

Set Time and Date

Set to Auto and Wait for

Light to Go Out

2 SETUP • LOAD BATTERY

Insert a fresh 6Volt/6ah lantern
battery or equivalent. Connect the
Red(+) & Black(-) clips to the battery
and lower the battery hold down
arms. Battery life is about 20 days
depending on temperature and
usage. When B = 20% Replace
battery.

SETUP • PROGRAMMING

SETUP MENU

Press the (MODE) button on the game camera to enter setup.
Press the (CHANGE BUTTONS) to scroll between setting
choices. The feature setting will flash in the LCD until set. Press
the (SELECT BUTTON) to accept settings and move to the next
selection. Programming will rotate between functions until you
exit the SETUP feature.

SETUP DATE/TIME

MM/DD/YY HH:MM

SEL

MM/

01 to 12

SEL

Press the (SELECT) button, LCD will show month (MM), use
(CHANGE) buttons to set month, press (SELECT) to move to

Day and change to set.

RESET EVENTS

SEL

NO

Scroll using the (CHANGE BUTTONS) to choose whether you
would like to reset the number of events counted. Choosing yes
will reset the events back to (00).

ERASE IMAGES

SEL

NO

Scroll using the (CHANGE BUTTONS) to choose to erase any
stored images on your game camera or optional memory card.
Choosing YES will reset the events back to (00).

HH:

SEL

00 to 23

/DD/

01 to 31

SEL SEL

YES

YES

SEL

:MM

00 to 59

SEL

SEL

/YY

00 to 35

DEFAULT SETTINGS

SEL

NO

Scroll using the (CHANGE BUTTONS) if you wish to set the
camera to its default factory settings.

YES

SEL

FLASH

SEL

ON

Scroll using the (CHANGE BUTTONS), Press select to choose
flash setting: (ON), (AUTO), OR (OFF). Security mode = (OFF):

Status light will remain off during this setting.

OFFAUTO

(SECURITY)

SEL

IMAGE MODE

SEL

STILL

Scroll using the (CHANGE BUTTONS). Press select to choose
between: (STILL), or (VIDEO).

VIDEO

SEL

IMAGE QUALITY

SEL

STANDARD

Scroll using the (CHANGE BUTTONS). Press select to choose
between the image quality choices.

HIGH

SEL

IMAGE DELAY

SEL

1 MIN

3O MIN 6O MIN

Scroll using the (CHANGE BUTTONS). Press select to choose
between the image quality choices.

5 MIN

1O MIN

SEL

SEL

MULTI-IMAGE

SEL

1-SHOT

Scroll using the (CHANGE BUTTONS). Press select to choose
the number of pictures to be shot in sequence.

CAMERA ID

Scroll using the (CHANGE BUTTONS).
Press select to set camera's ID number.

You are done with setup. To exit setup,
press the (MODE) button again.

2-SHOT 3-SHOT

MODE

OO

00 to 99

SEL

SEL

3 SETUP • MODE SELECTION

GENERAL OPERATION

Your digital game camera can be used two ways.

1) Automatic (AUTO) mode records images using infrared 
 detection. Use default or custom settings.

2) (HANDHELD) mode records images using manual  
 operation when circumstances warrant.

NOTE: NEVER OPERATE THE CAMERA WITH

SELECT MODE

Press the (MODE) button to scroll between modes. Choose
between two operational modes.

MODE SELECTIONS

(AUTO MODE) - Automatic operation.

MODE

FRONT DOOR OPEN.

MODE

Pictures taken
Total pictures

AUTO P=OO93/125O
E=3456 B=94% DLY

Displays when

EVENTS

BATTERY STRENGTH

(HANDHELD MODE) - Manual operation.

MODE

camera is
operating
with a delay.

HANDHELD B=94%
P=OO93/125O

(SETUP MODE) - Used to set Game Camera settings
This screen appears when the camera enters SETUP mode.
Additional menu screens appear as you move through the
SETUP functions. Please refer to (SETTING UP GAME
CAMERA) to identify the different SETUP screen displays.

MODE

SETUP DATE/TIME
MM/DD/YY HH:MM

4 SETUP • DEFINITIONS

CLOCK BATTERY

The small CR2025 button battery powers the clock. It
should be replaced as required.

TURNING THE UNIT ON / OFF

(POWER ON)In the Auto Mode the led flashes for 30
seconds before arming the system. When the LED goes out
the system is working. 

MFHDGC_INSTRUCTIONS_INSIDE SPREAD_8.26.05

(TURNING OFF) The unit saves all setup data and turns OFF.
Turning the unit ON & OFF resets the internal systems. This will
not change your settings or erase images.

EVENTS

(MULTIPLE PICTURES PER EVENT) Depending on user settings
the camera may take 1, 2 or 3 pictures per event spaced
approximately 15 seconds apart. If the camera fails to detect
motion after the first detection the camera will still take
subsequent pictures. When capture mode is set to video or the
camera is in (HANDHELD) mode this setting is ignored.

AUTOMATIC FUNCTIONS 

(LOW LIGHT OR NIGHT SITUATIONS) The video clip function
will be automatically switched to still photos in low light or night
situations.

NOTE: First still in video will reflect user setup setting.

(DELAY STATUS MENU)During (AUTO) mode, when delay
mode is activated it will be indicated on the LCD
panel as (DLY).

MEMORY ERROR MESSAGES

(MEMORY FULL) Turn off the unit; then turn it back on; when the
unit is turned on it goes directly to the (SETUP) mode; Go to the
(ERASE MEMORY) menu item to delete all the images from the
memory or SD Card.
(SD CARD LOCKED) Turn the unit off; remove the SD card;
unlock it; then insert it; then turn the unit back on.
(SD CARD BAD) Turn the unit off; remove the SD card; insert
a new SD card or clean the contacts; turn the unit back on.

5 OPERATIONS • MOUNTING

MOUNTING CAMERA

Using mounting straps, mount the
system securely in the desired
location.

OPERATIONS • AIMING LASER

LASER AIMING (optional)

If your Game camera is equipped with a laser aiming device,
slide the (POWER ON/OFF/AIM) Switch to the (AIM) position.
Using the laser aim your camera. The red dot indicates the target
area. Note you can also do "Walk" aim in the auto mode.

CAUTION: Looking into laser may be hazardous to the eyes.
Do not stare into beam or aim at other people unnecessarily.

CAUTION

LASER RADIATION

DO NOT STARE INTO BEAM

Product complies with applicable
requirements of 21 CFR 1040.10
and 1040.11

Laser Classification
Class II Laser Product
Wavelength: 650nm
Maximum Output: < 1mW

DIODE LASER

1mW MAX OUTPUT at 650 nm

CLASS II LASER PRODUCT