Motorola RDU4160d, RDU4163d User Manual

Download

Page 1

RDX™ Series Two-way Radios

User Guide

en-US fr-CA

RDU4160d & RDU4163d Display Model

Page 2

Open Source Software Legal Notices:

This Motorola Solutions product contains Open Source Software. For information regarding licenses, acknowledgements, required copyright notices and other usage terms, refer to the documentation for this Motorola Solutions product at: http://businessonline.motorolasolutions.com Go to: Resource Center > Product Information > Manual > Accessories.

Informations juridiques relatives aux logiciels libres :

Ce produit Motorola Solutions contient des logiciels libres. Pour obtenir des renseignements relatifs aux licences, aux attestations, aux avis de droits d'auteur requis et à d'autres conditions d'utilisation, reportez-vous à la documentation concernant ce produit Motorola Solutions à l'adresse suivante : http://businessonline.motorolasolutions.com Allez à l'adresse Resource Center > Product Information > Manual > Accessories.

Page 3

English

Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Product Safety. . . . . . . . . . . . . . . . . . . . . . . .5

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .6

Package Contents. . . . . . . . . . . . . . . . . . . . . .6

FCC Licensing Information . . . . . . . . . . . . .7

Interference Information . . . . . . . . . . . . . . . . .7

Canada Licensing Information. . . . . . . . . . .9

General Information. . . . . . . . . . . . . . . . . . . . .9

The License Application . . . . . . . . . . . . . . . . .9

Batteries and Chargers Safety Information . 10

Operational Safety Guidelines. . . . . . . . . . . .11

Radio Overview . . . . . . . . . . . . . . . . . . . . . .12

Parts Of The Radio . . . . . . . . . . . . . . . . . . . .12

On/Off/Volume Knob. . . . . . . . . . . . . . . .13

Channel Selector Knob. . . . . . . . . . . . . .13

Accessory Connector . . . . . . . . . . . . . . .13

Model Label . . . . . . . . . . . . . . . . . . . . . .13

Microphone . . . . . . . . . . . . . . . . . . . . . . .13

Antenna. . . . . . . . . . . . . . . . . . . . . . . . . .13

LED Indicator . . . . . . . . . . . . . . . . . . . . .13

Front Buttons . . . . . . . . . . . . . . . . . . . . . 13

Side Buttons. . . . . . . . . . . . . . . . . . . . . . . . . 14

The Lithium-Ion (Li-Ion) Battery . . . . . . . 14

Battery Features. . . . . . . . . . . . . . . . . . . . . . 15

About the Li-Ion Battery . . . . . . . . . . . . . 15

Battery Recycling and Disposal . . . . . . . 16

Installing the Lithium-Ion (Li-Ion)

Battery . . . . . . . . . . . . . . . . . . . . . . . . 17

Removing the Lithium-Ion (Li-Ion)

Battery . . . . . . . . . . . . . . . . . . . . . . . . 17

Attaching the Antenna . . . . . . . . . . . . . . 18

Removing the Antenna . . . . . . . . . . . . . 18

Installing Spring Action Belt clip. . . . . . . 19

Power Supply, Adaptor and Drop-in Tray

Charger . . . . . . . . . . . . . . . . . . . . . . . 19

Battery Life Information . . . . . . . . . . . . . 20

Charging the Battery . . . . . . . . . . . . . . . 21

Drop-in Tray Charger LED Indicators . . 23

Estimated Charging Time . . . . . . . . . . . 25

Multi-Unit Charger LED Indicators . . . . . 27

Getting Started . . . . . . . . . . . . . . . . . . . . . . 28

Turning radio ON/OFF . . . . . . . . . . . . . . . . . 28

Adjusting Volume . . . . . . . . . . . . . . . . . . . . . 28

CONTENTS

Page 4

English

READING THE DISPLAY . . . . . . . . . . . . . . .28

Selecting a Channel . . . . . . . . . . . . . . . . . . .28

Talking and Monitoring . . . . . . . . . . . . . . . . .29

Receiving a Call . . . . . . . . . . . . . . . . . . . . . .29

Signal strength indicator and channel busy

indicators . . . . . . . . . . . . . . . . . . . . . . . . . .29

Talk Range . . . . . . . . . . . . . . . . . . . . . . . . . .30

Radio LED Indicators . . . . . . . . . . . . . . . . . .31

Hands-Free Use/VOX . . . . . . . . . . . . . . . . . .32

With Compatible VOX Accessories. . . . .32

CONTENTS

Hands Free without Accessories (iVOX).32

Toggle Voice Prompt in User Mode . . . . . . .33

Power Up - Tone Mode . . . . . . . . . . . . . . . . .33

Reset to Factory Defaults . . . . . . . . . . . . . . .33

Keypad Beeps. . . . . . . . . . . . . . . . . . . . . . . .33

Keypad Lock/Unlock . . . . . . . . . . . . . . . . . . .33

Menu Options . . . . . . . . . . . . . . . . . . . . . . . .34

Setting VOX/IVOX Sensitivity . . . . . . . . . . . .34

Microphone Gain. . . . . . . . . . . . . . . . . . . . . .35

Programming Features . . . . . . . . . . . . . . . .36

Advanced Configuration Mode . . . . . . . . . . .36

Entering Advanced Configuration Mode .36 Programming RX (Reception) Frequencies .37

Programming RX (Reception) codes (CTCSS/

DPL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Programming Scramble . . . . . . . . . . . . . . . . 38

Programming Maximum Number of

Channels . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Programming Call Tones . . . . . . . . . . . . . . . 39

Programming Microphone Gain Level . . . . . 39

Programming Microphone Accessory Gain

Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Other Programming Features . . . . . . . . . . . 41

Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Programming Scan List . . . . . . . . . . . . . 41

Programming Weather Channel (Not

allowed on RDX4163) . . . . . . . . . . . . 42

Editing Channel Alias Name . . . . . . . . . 42

Nuisance Channel Delete . . . . . . . . . . . 43

Customer Programming Software (CPS) . . . 44

Time-Out Timer . . . . . . . . . . . . . . . . . . . 44

Power Select . . . . . . . . . . . . . . . . . . . . . 44

Call Tones . . . . . . . . . . . . . . . . . . . . . . . 45

Scramble . . . . . . . . . . . . . . . . . . . . . . . . 45

Reverse Burst . . . . . . . . . . . . . . . . . . . . 45

Text-to-Speech (Changing Pre-Defined Voice

Page 5

English

Aliases). . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Enable User Pre-Defined Voice Prompt

(VP) Checkbox . . . . . . . . . . . . . . . . . .45

User Pre-Defined Voice Prompt (VP) Text .

Import Voice File. . . . . . . . . . . . . . . . . . .45

Listen to User Customized Voice Prompt

(VP) Text. . . . . . . . . . . . . . . . . . . . . . .46

Weather Feature (Not for RDU4163) . . . . . .46

Weather Alert Mode . . . . . . . . . . . . . . . .47

Weather Channel Frequencies Table . . .47

The Weather Alert has two modes of operations

EOM Enabled . . . . . . . . . . . . . . . . . . . . .48

New Alert Tone Timer. . . . . . . . . . . . . . .48

Event Type Filter . . . . . . . . . . . . . . . . . . . . . .48

All Events . . . . . . . . . . . . . . . . . . . . . . . .49

Alert Test Event . . . . . . . . . . . . . . . . . . .49

Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Watch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Emergency . . . . . . . . . . . . . . . . . . . . . . . . . .49

Statement . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Event Code Filter. . . . . . . . . . . . . . . . . . . . . .50

Block Event . . . . . . . . . . . . . . . . . . . . . . . . . 50

Event Code . . . . . . . . . . . . . . . . . . . . . . . . . 50

The Critical Events Table . . . . . . . . . . . . . . . 50

Geographic Filter . . . . . . . . . . . . . . . . . . . . . 52

State. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

County . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

FIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Cloning Radios. . . . . . . . . . . . . . . . . . . . . . . 53

Cloning with a Multi Unit Charger

(MUC) . . . . . . . . . . . . . . . . . . . . . . . . 53

Cloning Radio using the Radio to Radio

(R2R) Cloning Cable (Optional

Accessory) . . . . . . . . . . . . . . . . . . . . . 54

Cloning using the Customer Programming

Software (CPS) . . . . . . . . . . . . . . . . . 57

Troubleshooting. . . . . . . . . . . . . . . . . . . . . 58

Use and Care . . . . . . . . . . . . . . . . . . . . . . . 62

Frequency and Code Charts . . . . . . . . . . . 63

RDX UHF Frequencies Chart. . . . . . . . . . . . 63

RDU4163 – UHF Default Frequencies

Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

RDX UHF Frequencies Chart. . . . . . . . . . . . 65

RDU4160 – UHF Default Frequencies

CONTENTS

Page 6

English

Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Programming Customized Frequencies On

RDU4160 . . . . . . . . . . . . . . . . . . . . . . . . . .69

CTCSS and PL/DPL Codes . . . . . . . . . . . . .70

Accessories . . . . . . . . . . . . . . . . . . . . . . . . .75

Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Audio Accessories. . . . . . . . . . . . . . . . . . . . .75

Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Carry Accessories . . . . . . . . . . . . . . . . . . . . .76

CONTENTS

Software Applications . . . . . . . . . . . . . . . . . .76

Power supplies ac pin adapters . . . . . . . . . .76

Power supplies . . . . . . . . . . . . . . . . . . . . . . .76

Motorola Solutions Limited Warranty for the

United States and Canada . . . . . . . . . . . . .77

Page 7

English

PRODUCT SAFETY

C a u t i o n

PRODUCT SAFETY AND RF EXPOSURE COMPLIANCE

Before using this product, read the operating instructions and RF energy awareness information contained in the Product Safety and RF Exposure booklet enclosed with your radio.

ATTENTION!

This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.

For a list of Motorola Solutions-approved antennas, batteries and other accessories, visit the following website which lists approved accessories:

www.motorolasolutions.com/RDX

PRODUCT SAFETY

Page 8

English

INTRODUCTION

Thank you for purchasing the Motorola Solutions® RDX Series™ Radio. This radio is a product of Motorola Solutions' 80 plus years of experience as a world leader in the designing and manufacturing of communications equipment. The RDX Series radios provide cost-effective communications for businesses such as retail stores, restaurants, schools, construction sites, manufacturing, property and hotel management and more. Motorola Solutions professional two-way radios are the perfect communications solution for all of today's fast-paced industries.

INTRODUCTION

Note: Read this user guide carefully to ensure you

know how to properly operate the radio before use

PACKAGE CONTENTS

• Radio

• Antenna

• Lithium-Ion Battery

• Belt Clip

• Power Supply

• Quick Reference Guide

• Drop-in Tray Charger

• Product Safety & RF Exposure Booklet

For a copy of a large-print version of this user guide or for product-related questions, contact

1-800-448-6686 in the USA 1-800-461-4575 in Canada 1-888-390-6456 on TTY (Text Telephone)

For product related information, visit us at:

www.motorolasolutions.com/RDX

Business Radios RPSD 1C15, Motorola

8000 West Sunrise Boulevard Plantation, Florida 33322

Page 9

English

FCC LICENSING INFORMATION

INTERFERENCE INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

RDX Series Business two-way radios operate on radio frequencies that are regulated by the Federal Communications Commission (FCC).

To transmit on these frequencies, you are required to have a license issued by the FCC. Application is made available on FCC Form 601 and Schedules D, H, and Remittance Form

159.

To obtain these FCC forms, request document 000601 which includes all forms and instructions. If you wish to have the document faxed, mailed or have questions, use the following contact information.

FCC LICENSING

INFORMATION

Faxed contact the

Fax-On- Demand

system at:

1-202-418-0177 1-800-418-FORM

Mailed call the FCC forms hotline at:

1-800-418-3676

Questions regarding FCC

license contact the FCC at:

1-888-CALL-FCC 1-888-225-5322 Or: http://www.fcc.gov

Page 10

English

Before filling out your application, you must decide which frequency(ies) you can operate on. See “Frequencies and Code Charts”. For questions on determining the radio frequency, call Motorola Solutions Product Services at:

1-800-448-6686

Changes or modifications not expressly approved by Motorola Solutions may void the

INFORMATION

FCC LICENSING

user’s authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services.

Replacement of any transmitter component (crystal, semiconductor and more.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.

Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.

Page 11

English

CANADA LICENSING INFORMATION

GENERAL INFORMATION

The operation of your Motorola Solutions radio is subject to the Radiocommunications Act and must comply with rules and regulations of the Federal Government’s department of Industry Canada. Industry Canada requires that all operators using Private Land Mobile frequencies obtain a radio license before operating their equipment.

An application for your Industry Canada license is made on the form included with your radio. Additional forms and latest license application versions can be obtained from the nearest Industry Canada District office. A list of these offices is included for your information.

This device complies with Industry Canada’s licenceexempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference; and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

THE LICENSE APPLICATION

General Instructions

1. Fill in the items as per the instructions. If you

need additional space for any item use the reverse side of the application.

2. Be sure to use a typewriter or print legibly.

3. Make a copy for your files.

4. Prepare a cheque or money order made out to

the “Receiver General for Canada”, for an amount, which is on the following schedule, for each radio purchased. (License is valid until April 1st of each year, and the renewed.

5. Mail your completed application, along with your

cheque or money order to the closest Industry Canada District office, according to the list on pages.

To obtain the latest Canadian License Application form, please go to:

www.ic.gc.ca

CANADA LICENSING

INFORMATION

Page 12

English

BATTERIES AND CHARGERS SAFETY INFORMATION

This document contains important safety and operating instructions. Read these instructions carefully and save them for future reference.

Before using the battery charger, read all the instructions and cautionary markings on

• the charger,

• the battery, and

• the radio using the battery

SAFETY INFORMATION

1. To reduce risk of injury, charge only the

BATTERIES AND CHARGERS

rechargeable Motorola Solutions-authorized batteries. Other batteries may explode, causing personal injury and damage.

2. Use of accessories not recommended by

Motorola Solutions may result in risk of fire, electric shock, or injury.

3. To reduce risk of damage to the electric plug

and cord, pull by the plug rather than the cord when disconnecting the charger.

4. An extension cord should not be used unless

absolutely necessary. Use of an improper extension cord could result in risk of fire and electric shock. If an extension cord must be used, make sure that the cord size is 18AWG for lengths up to 100 ft (30.48 m), and 16AWG for lengths up to 150 ft (45.72 m).

5. To reduce risk of fire, electric shock, or injury, do

not operate the charger if it has been broken or damaged in any way. Take it to a qualified Motorola service representative.

6. Do not disassemble the charger; it is not

repairable and replacement parts are not available. Disassembly of the charger may result in risk of electrical shock or fire.

7. To reduce risk of electric shock, unplug the

charger from the AC outlet before attempting any maintenance or cleaning

Page 13

English

OPERATIONAL SAFETY GUIDELINES

• Turn the radio OFF when charging battery.

• The charger is not suitable for outdoor use. Use

only in dry locations/conditions.

• Connect charger only to an appropriately fused

and wired supply of the correct voltage (as specified on the product).

• Disconnect charger from line voltage by removing

main plug.

• The outlet to which this equipment is connected

should be nearby and easily accessible.

• In equipment using fuses, replacements must

comply with the type and rating specified in the equipment instructions.

• Maximum ambient temperature around the power

supply equipment must not exceed 40 °C (104 °F).

• Power output from the power supply unit must not

exceed the ratings stated on the product label located at the bottom of the charger.

• Make sure that the cord is located where it will not be stepped on, tripped over, or subjected to water, damage, or stress.

BATTERIES AND CHARGERS

SAFETY INFORMATION

Page 14

English

Antenna

On/Off/Volume Knob

LED Indicator

Channel Selector Knob

Audio Accessory 2 Pin Connector

PTT (Push-ToTalk) Button

Battery

Microphone

SB1

SB2

Programmable Button A

Menu Button

Display

Model Label

RADIO OVERVIEW

PARTS OF THE RADIO

Page 15

English

On/Off/Volume Knob

Programmable Button A

Menu Button

Used to turn the radio ON or OFF and to adjust the radio’s volume.

Channel Selector Knob

Used to switch the radio to different channels.

Accessory Connector

Used to connect compatible audio accessories.

Model Label

Indicates the model of the radio.

Microphone

Speak clearly into the microphone when sending a message.

Antenna

For models RDX4160 and RDX4163 the antennas are removable.

LED Indicator

Used to give battery status, power-up status, radio call information and scan status.

Front Buttons

RADIO OVERVIEW

Menu Button

• Gives access to set up features like VOX/iVOX levels, etc. It also allows you to move through all the features while in Programming Mode. Default set to preset Channel 1.

Programmable Button A

• Allows you to choose level or toggle options for features the Menu is on. Default set to generate current programmed call tone.

Programmable Button B

• Allows you to choose level or toggle options for features the Menu is on. Default set to Backlight Mode.

Note: A short press of either Programmable

Button (A or B) tunes the radio to the preset

Page 16

English

channel and the radio will play a good chirp. You can assign different functions to these buttons via the CPS. For example: Backlight Time Out, Reverse Burst, Scan/Nuisance Channel Delete, Monitor and Call Tones. To learn more about how to program these buttons, refer to “Advanced Configuration Mode” on page 36 and “Customer Programming Software (CPS)” on page 44.

SIDE BUTTONS

Push-to-Talk (PTT) Button

• Press and hold down this button to talk, release it

RADIO OVERVIEW

to listen.

Side Button 1 (SB1)

• The Side Button 1 is a general button that can be configured by the Customer Programming Software - CPS. The default setting of SB1 is ‘Monitor’.

Side Button 2 (SB2)

• The Side Button 2 is a general button that can be configured by the CPS. The SB2 default setting is ‘Scan/Nuisance Channel Delete’.

The Lithium-Ion (Li-Ion) Battery

RDX Series comes with a Standard Capacity Li-Ion battery. Other batteries may be available. For more information, see “Battery Features” on page 15.

This User Guide covers multiple RDX Series models, and may detail some features your radio does not have. The radio’s model is shown on the bottom of the radio and provides the following information:

Page 17

English

Table 1: RDX Series Radio Specifications

Model

RDU4160 UHF 4 16 Removable

RDU4163 UHF 4 16 Removable

BATTERY FEATURES

RDX Series radios provide Lithium-Ion batteries that come in different capacities that defines the battery life.

About the Li-Ion Battery

The RDX Series radio comes equipped with a rechargeable Li-Ion battery. This battery should be fully charged before initial use to ensure optimum capacity and performance.

Battery life is determined by several factors. Among the more critical are the regular

Frequency

Band

Transmit

Power (W)

Number of

Channels

overcharge of batteries and the average depth of discharge with each cycle. Typically, the greater the overcharge and the deeper the average discharge, the fewer cycles a battery will last. For example, a battery which is overcharged and discharged 100% several times a day, lasts fewer cycles than a battery that receives less of an overcharge and is discharged to 50% per day. Further, a battery which receives minimal overcharging and averages only 25% discharge, lasts even longer.

Antenna

RADIO OVERVIEW

Page 18

English

Motorola Solutions batteries are designed specifically to be used with a Motorola Solutions charger and vice versa. Charging in non-Motorola Solutions equipment may lead to battery damage and void the battery warranty. The battery should be at about 77 °F (25 °C) (room temperature), whenever possible. Charging a cold battery (below 50 °F [10 °C]) may result in leakage of electrolyte and ultimately in failure of the battery. Charging a hot battery (above 95 °F [35 °C]) results in reduced discharge capacity, affecting the performance of the radio. Motorola Solutions

RADIO OVERVIEW

rapid-rate battery chargers contain a temperature-sensing circuit to ensure that batteries are charged within the temperature limits stated above.

Battery Recycling and Disposal

Li-Ion rechargeable batteries can be recycled. However, recycling facilities may not be available in all areas. Under various U.S. state laws and the laws of several other countries,

batteries must be recycled and cannot be disposed of in landfills or incinerators. Contact your local waste management agency for specific requirements and information in your area. Motorola Solutions fully endorses and encourages the recycling of Li-Ion batteries. In the U.S. and Canada, Motorola Solutions participates in the nationwide Rechargeable Battery Recycling Corporation (RBRC) program for Li-Ion battery collection and recycling.

Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, access RBRC's Internet web site at:

http://www.call2recycle.org

or call:

(877)723-1297

This internet site and telephone number also provides other useful information concerning

Page 19

English

recycling options for consumers, businesses,

Battery Latch

Slots

Battery Latch

and governmental agencies.

Installing the Lithium-Ion (Li-Ion) Battery

radio until a click is heard.

Note: To learn about the Li-Ion Battery Life

features, refer to “About the Li-Ion Battery” on page 15

Removing the Lithium-Ion (Li-Ion) Battery

RADIO OVERVIEW

1. Turn OFF the radio.

2. With the Motorola Solutions logo side up on the

battery pack, fit the tabs at the bottom of the battery into the slots at the bottom of the radio’s body.

3. Press the top part of the battery towards the

1. Turn OFF the radio.

2. Push down the battery latch and hold it while

removing the battery.

3. Pull the battery away from the radio.

Page 20

English

Attaching the Antenna

RADIO OVERVIEW

Removing the Antenna

1. Align the threaded end of the antenna with the

radio’s antenna connector.

2. Turn the antenna clockwise to fasten it.

1. Turn the antenna counter-clockwise until you

can remove it.

Note: These instructions apply ONLY to models

RDU4100 and RDV5100. Do not attempt to remove the antenna if your radio is not one of these models.

Page 21

English

Installing Spring Action Belt clip.

Belt Clip Tab

Spring Action Belt Clip

Drop-in Tray Charger Power Supply

1. Slide the spring action belt clip rails into the belt

clip grooves on the back of the battery pack and slide it down until the belt clip tab snaps into place.

2. To remove, pull back the metal release tab on

the belt clip tab and push the spring action belt clip upward to remove.

Power Supply, Adaptor and Drop-in Tray Charger

RADIO OVERVIEW

The radio is equipped with one Drop-in Tray Charger and one Power Supply with Adaptor. For more information, refer to “Chargers” on page 76.

Page 22

English

Battery Life Information

When the Battery Save feature is set to ON (enabled by default), the battery life lasts

Table 2: Li-Ion Battery Life with Battery Save feature ON

Battery Type 5 W 4 W

High Capacity 15 hr 15 hr

longer. The following table summarizes battery life estimations:

RADIO OVERVIEW

Note: Battery life is estimated based on 5%

transmit / 5% receive / 90% standby standard duty cycle.

Page 23

English

Charging the Battery

Power Supply

Drop-In Tray Charger

The RDX Series radio offers two types of Chargers:

• Standard Charger and,

• Rapid Charger

Note: The radio comes with a Standard Power

Supply.

To charge the battery (with the radio attached), place it in a Motorola Solutions-approved Dropin Tray Single Unit Charger or Drop-in Tray Multi Unit Charger.

Note: When acquiring additional chargers or

power supplies, make sure you have similar drop-in tray chargers and power supplies sets (all “rapid” or all “standard”). For part number details, refer to “Chargers” on

page 76

Charging with the Drop-in Tray Single Unit Charger (SUC)

RADIO OVERVIEW

1. Place the Drop-in Tray Charger on a flat

surface.

2. Insert the connector of the Power Supply into

the charger port on the back of the Drop-in Tray Charger.

3. Plug the AC Adaptor into a power outlet.

4. Insert the radio into the Drop-in Tray Single Unit

Charger with the radio facing the front, as shown.

Page 24

English

Note: When charging a battery attached to the

radio, turn the radio OFF to ensure a full charge. See “Operational Safety Guidelines” on page 11 for more information.

Charging A Stand-Alone Battery

RADIO OVERVIEW

To charge only the battery - at step 4 on page 21, insert the battery into the tray, with the inside surface of the battery facing the front of the Drop-in Tray Single Unit Charger as shown above. Align the slots in the battery with the alignment ribs in the Drop-in Tray Single Unit Charger.

Note: Ensure that the bracket in the charger is

adjusted to the correct position for either Standard or High capacity battery. See “Charging a Standard Battery” on the right.

Page 25

English

Drop-in Tray Charger LED Indicators

Table 3: Standard Charger LED Indicator

Status LED Indicator Comments

Power On Steady red indication for 3 s The charger has powered up

Charging Blinking red (slow) The charger is currently charging

Charging Complete Steady red indication Battery is fully charged

Battery Fault (*) Blinking red (fast)

(*) Normally, re-positioning the battery pack will correct this issue.

RADIO OVERVIEW

Battery had a fault when battery was inserted

Page 26

English

Table 4: Rapid Charger LED Indicator

Status LED Indicator Comments

Power On Steady green indication for 3 s The charger has powered up

Charging Blinking green The charger is currently charging

Top-off Charging Blinking green (slow) Battery is near fully charged

Charging Complete Steady green indication Battery is fully charged

Battery Fault (*) Blinking red (fast)

Waiting to Charge (**) Double-blink yellow indications

(*) Normally, re-positioning the battery pack will

RADIO OVERVIEW

correct this issue. (**) Battery temperature is too warm or too cold or wrong power voltage is being used.

Battery had a fault when battery was inserted

Battery charging conditions not suitable

Page 27

English

Estimated Charging Time

The following table provides the estimated charging time of the battery. For more

Table 5: Battery Estimated Charging Time

Charging Solutions

Standard 12 hr

Rapid 3 hr

information, see “Audio Accessories” on page 75.

RADIO OVERVIEW

Estimated Charging Time

High Capacity Battery

Page 28

English

Charging a Radio and Battery using a Multi Unit-Charger - MUC (Optional Accessory)

The Multi-Unit Charger (MUC) allows drop-in charging of up to six radios or batteries. Batteries can be charged with the radios or removed and placed in the MUC separately.

RADIO OVERVIEW

Each of the six charging pockets can hold a radio (with or without the Holster) or battery, but not both.

1. Place the Multi-Unit Charger on a flat surface.

2. Insert the power cord plug into the MUC’s dual

pin connector .

3. Plug the power cord into an AC outlet.

4. Turn the radio OFF.

5. Set removable bracket for battery type

6. Insert the radio or battery into the charging

pocket with the radio.

Note:

• This Multi-Unit Charger clones up to three radios (three Source radios and three Target radios). Refer to “Cloning with a Multi Unit Charger (MUC)” on page 53 for more information.

• More information on the Multi-Unit Charger’s operation is available in the Instruction Sheets provided with the MUC. For more information on the parts and their part numbers, refer to Chapter “Accessories” on page 75.

Page 29

English

Multi-Unit Charger LED Indicators

Table 6: MUC Charger LED Indicator

Status LED Indicator Comments

Charging Steady Red Indication The charger is currently charging

Charging Complete Steady Green Indication Battery is fully charged

Battery Fault (*) Blinking red (fast) Battery was faulty when inserted

(*) Normally, re-positioning the battery pack will correct this issue.

RADIO OVERVIEW

Page 30

English

GETTING STARTED

Hi Power

Scramble

Keypad Lock

Vox / iVox

Scan

Battery Level

Signal Strength

Channel Number

Interference Eliminator Code Indicator

Frequency Indicator

Programming Mode Indicator

Channel Indicator

GETTING STARTED

For the following explanations, refer to “Parts Of The Radio” on page 12.

TURNING RADIO ON/OFF

To turn ON the radio, rotate the On/Off/Volume Knob clockwise. The radio plays one of the following:

• Power up tone and channel number announcement, or

• Battery level and channel number announcements, or

• Silent (Audible tones disabled)

The LED blinks red briefly. To turn the radio OFF, rotate the On/Off/Volume Knob

counterclockwise until you hear a ‘click’ and the radio LED Indicator turns OFF.

ADJUSTING VOLUME

Turn the On/Off/Volume Knob clockwise to increase the volume, or counterclockwise to decrease the volume.

Note: Do not hold the radio too close to the ear

when the volume is high or when adjusting the volume

READING THE DISPLAY

Note: The radio display shown here is for icon

location only. Each radio display may appear different (channel and code) based on the pre-programmed radio defaults and features available in the model or region. Pressing any button, except the PTT button, will turn on the backlight.

SELECTING A CHANNEL

To select a channel, turn the Channel Selector Knob until you reach the desired channel. An audible voice indicates the selected channel.

Each channel has its own Frequency, Interference Eliminator Code and Scan Settings.

Page 31

English

TALKING AND MONITORING

Signal Strength Indicator

It is important to monitor for traffic before transmitting to avoid ‘talking over’ someone who is already transmitting

To monitor, long press and hold the SB1(*) button to access channel traffic. If no activity is present, you will hear ‘static’. To release, press SB1 again. Once channel traffic has cleared, proceed with your call by pressing the PTT button. When transmitting, the LED Indicator stays solid red.

• To listen to all activity on a current channel, short press the SB1 to set the CTCSS/DPL code to 0. This feature is called ‘CTCSS/DPL Defeat (Squelch set to SILENT)’.

• (*) This assumes SB1 is not being programmed for a different mode.

RECEIVING A CALL

1. Select a channel by rotating the Channel

Selector Knob until you reach the desired channel. An audible voice indicates the selected channel.

2. Make sure the PTT button is released and listen

for voice activity.

3. The LED Indicator stays solid red when the

radio is receiving a call.

4. To respond, hold the radio vertically 1 to 2

inches (2.5 to 5cm) from mouth. Press the PTT button to talk; release it to listen.

SIGNAL STRENGTH INDICATOR AND CHANNEL BUSY INDICATORS

When there is activity on a frequency, the radio displays the Signal Strength Indicator icon and the radio LED blinks faster. When your radio is receiving (Rx) and there is activity on the same frequency and code as your radio, the radio Signal Strength Indicator icon can change from 1 (weakest) to 6 (strongest) depending on the radio reception coverage. This helps you to determine if your radio is moving out of range.

Note: Obstacles blocking the signal path affects

the strength of incoming signal.

GETTING STARTED

Page 32

English

TALK RANGE

Industrial Multi-Level

Model

UHF 4W Up to 350,000 ft2 Up to 30 Floors

To establish a proper two-way communication, the channel, frequency, and interference eliminator codes must be the same on both radios. This depends on

GETTING STARTED

the stored profile that has been preprogrammed on the radio:

1. Channel: Current channel that the radio is

using, depending on radio model.

2. Frequency: The frequency the radio uses to

transmit/receive.

3. Interference Eliminator Code: These codes

help minimize interference by providing a choice of code combinations.

Inside steel/

concrete Industrial

buildings

Inside multi-

level buildings

4. Scramble Code: Codes that make the

transmissions sound garbled to anyone listening who is not set to that specific code.

5. Bandwidth: Some frequencies have selectable

channel spacing, which must match other radios for optimum audio quality.

For details on how to set up frequencies and CTCSS/ DPL codes in the channels, refer to “Advanced Configuration Mode” on page 36.

Page 33

English

RADIO LED INDICATORS

RADIO STATUS LED INDICATION

Channel Busy Solid Orange

Cloning Mode Double Orange Heartbeats

Cloning In Progress Solid Orange

Fatal Error at Power up

Low Battery Orange Heartbeat

Low Battery Shutdown Fast Orange Heartbeat

Monitor LED is OFF

Power-Up Solid Red for 2 s

‘Idle’ Programming Mode / Channel Mode

Scan Mode Fast Red Heartbeat

Transmit (TX)/Receive (RX) Solid Red

Transmit in Low Power Select Solid Orange

VOX/iVOX Mode Double Red Heartbeats

One Green Blink, One Orange Blink, One Green Blink, then repeat for 4 seconds

Green Heartbeat

GETTING STARTED

Page 34

English

HANDS-FREE USE/VOX

VOX Accessory

Accessory Port/ Connector

Motorola Solutions RDX Series radios can operate hands-free (VOX) when used with compatible VOX

GETTING STARTED

accessories.

With Compatible VOX Accessories

The default factory setting for VOX sensitivity level is OFF (level ‘0’). Before using VOX, set VOX level to a level different from ‘0’ via the Customer Programming Software (CPS). Then, perform the following steps:

1. Turn the radio OFF.

2. Open accessory cover.

3. Insert the audio accessory’s plug firmly into

accessory port.

4. Turn radio ON. The LED Indicator will blink

double red

5. Lower radio volume BEFORE placing

accessory near ear.

6. To transmit, speak into accessory microphone

and to receive, stop talking.

7. VOX can be temporarily disabled by pressing

the PTT button or by removing the audio accessory.

VOX can also be activated using the (Menu) button without using the CPS.

Note: To order accessories, refer to:

www.motorolasolutions.com/RDX,

call 1 (800) 448-6686, or contact your Motorola Solutions point of purchase.

Hands Free without Accessories (iVOX)

• Press the PTT button while turning ON the radio to enable iVOX. The icon blinks.

• iVOX can be temporarily disabled by pressing the

Page 35

English

PTT button.

Keypad Lock icon

• A short press of the PTT Button re-enables iVOX

Note:

• There is a short delay between the time when you start talking and when the radio transmits.

• For more information on setting VOX/iVOX sensitivity, refer to “Setting VOX/IVOX Sensitivity” on page 34.

TOGGLE VOICE PROMPT IN USER MODE

Short press the SB1 Button while turning ON the radio to enable/disable the Voice Prompt in User Mode. (Default is set to ON).

POWER UP - TONE MODE

To enable/disable power up tone mode, press SB1 and SB2 buttons simultaneously for 2-3 seconds while powering up the radio until you hear the preprogrammed power up tone. Three different power-up tones are available.

• Power up tone and channel number announcement, or

• Battery level and channel number announcements, or

• Silent (Audible tones disabled)

RESET TO FACTORY DEFAULTS

Reset to Factory Defaults will set back all radio features to the original factory default settings. To do so, press PTT, SB2 and SB1 simultaneously while turning ON the radio until you hear a high tone chirp.

KEYPAD BEEPS

To enable/disable Keypad Beeps, short press the SB2 button while turning ON the radio until you hear ‘chirp’ tone.

KEYPAD LOCK/UNLOCK

You can lock the keypad to avoid accidentally changing your radio settings. To lock the radio keypad, press and hold the (Menu) button for 4 seconds.

Note: The PTT Button and Programmable Button

A (if Call Tone feature has been assigned) cannot be locked using this feature.

GETTING STARTED

Page 36

English

MENU OPTIONS

To access the radio MENU, short press the (Menu) button. The radio displays the feature options. For each options, use the and buttons to navigate. After selecting your desired option settings, you can:

• Press (Menu) button to save and go to the next option, or

• Long press the PTT button to save and exit, or

• Turn OFF the radio to exit without saving the changes.

The MENU mode times out automatically if there is no activity detected for more than 10 seconds.

SETTING VOX/IVOX SENSITIVITY

The VOX/iVOX sensitivity settings can be adjusted via

GETTING STARTED

the MENU as well as the CPS. To modify via the MENU, make sure you have enabled VOX or iVOX. (Refer to “Hands-Free Use/VOX” on page 33 or “Hands Free without Accessories (iVOX)” on page 34 for more information). Once VOX/iVOX is enabled, short press the (Menu) button.

If iVOX is enabled when you press the (Menu) button, the radio displays the following:

If VOX is enabled (with accessory connected to the radio) when you press the (Menu) button, the radio displays the following:

To change the sensitivity level, use the Programmable Button A and Programmable Button B buttons:

• 0 = OFF (For VOX accessories only)

• 1 = Low sensitivity

• 2 = Medium sensitivity

• 3 = High sensitivity

Once you have selected the desired sensitivity level, you can:

Page 37

English

• Press the (Menu) button to go to the next step, or

• Turn OFF the radio to exit without saving changes.

Note: The default sensitivity is ‘Medium’ for VOX

and ‘High’ for iVOX.

MICROPHONE GAIN

The sensitivity of the microphone can be adjusted to fit different users or operating environments.

This feature can be adjusted only through the CPS. Microphone default setting is set to level 2 (medium gain).

GETTING STARTED

Page 38

English

PROGRAMMING FEATURES

Advanced Configuration Mode

PROGRAMMING FEATURES

ADVANCED CONFIGURATION MODE

Advanced Configuration is a configuration mode that allows the customization of additional features via the radio’s front panel.

Entering Advanced Configuration Mode

To enter Advanced Configuration Mode, press and hold the PTT Button and the SB1 Button simultaneously for 3 s, while turning ON the radio. A unique tone sounds, indicating the radio has entered Advanced Configuration Mode. The radio LED blinks a green heartbeat.

Note:

• The Advanced Configuration Mode defaults to the ‘Idle’ Programming Mode.

• ‘Idle’ Programming Mode is the stage in the Programming Mode where the radio waits for the user to start the radio programming cycle.

When the radio is set to Advanced Configuration Mode, the k icon displays and the current channel aliasing name blinks to indicate that you can rotate the

Channel Selector Knob to select the channel you want to program.

In Advanced Configuration Mode, the radio is capable of setting values for each channel by toggling between the different programming modes available:

• Frequencies,

• CTCSS/DPL Codes (Interference Eliminator Code),

• Scramble,

• Maximum Channels,

• Call Tone,

• Microphone Gain,

• Scan, and

• Weather Channel.

• To move along the different Programming Selection Mode without saving changes, short press the PTT Button or (Menu) Button.

• To save changes, long press the PTT Button. The radio returns to ‘Idle’ Programming Mode.

Page 39

English

• When in ‘Idle’ Programming Mode, long press the PTT button to exit the Programming Mode.

• Whenever you wrap around to the beginning of the Programming Mode options, the radio automatically saves all changes made, even if you turn OFF the radio.

• Exit the Programming Mode without saving changes (as long as you have not wrapped around to the beginning of the Programming Mode options) by turning OFF the radio.

PROGRAMMING RX (RECEPTION) FREQUENCIES

Once you have chosen the channel you want to program, short press the PTT button or (Menu) button to scroll through the options until you reach ‘Frequency Programming Mode’.

The radio display shows the frequency code as follows:

To program the desired frequency, use the Programmable Button A and Programmable Button B buttons to navigate to the frequency code value you need. Long press the PTT button to exit and save, or short press the PTT button to move to the next programming feature without saving.

PROGRAMMING RX (RECEPTION) CODES (CTCSS/DPL)

Once you have chosen the channel you want to program, short press the PTT button or (Menu) button to scroll through the options until you reach the ‘Code Programming Mode’.

The radio display shows the CTCSS/DPL code as follows:

To program the desired code, use the and buttons until you get the CTCSS/DPL code value you want to set up. Long press the PTT button to exit and save, or short press the PTT button to move to the next programming feature without saving.

PROGRAMMING FEATURES

Page 40

English

PROGRAMMING FEATURES

PROGRAMMING SCRAMBLE

The scramble feature makes your transmissions sound garbled to anyone listening without the same scramble code. It does not guarantee confidentiality, but it adds an extra layer of privacy. Scramble mode is by default set to ‘OFF’.

Once you have entered Advanced Configuration Mode and selected the channel in which you want to enable Scramble, scroll up or down through the programming modes by short pressing the PTT button or (Menu) button until the radio reaches the Scramble Programming Mode.

The radio display shows the Scramble settings as follows:

The current scramble value blinks. You can select the desired scramble value (0,1,2 or 3) by pressing the and buttons. Long press the PTT button to exit and save, or short press the PTT button to move to the next programming feature without saving.

Note: The values available for scrambling are

dependent to the values programmed viathe CPS. Scramble is disabled when the value is set to ‘0’.

PROGRAMMING MAXIMUM NUMBER OF CHANNELS

You can configure the maximum number of channels for the radio. Once you have entered the Advanced Configuration Mode, scroll up or down through the programming modes by short pressing the PTT button or (Menu) button until you reach the ‘Maximum Channel Programming Mode’.

The radio display shows the Maximum Number of Channels as follows:

The radio display blinks the current maximum number of channels programmed. Use the Programmable Button A and Programmable Button B buttons until you get the desired maximum number of channels. Long press the PTT button to exit and save, or short

Page 41

English

press the PTT button to move to the next programming feature without saving.

The values available for maximum channel settings are dependent on the maximum number of channels the radio supports.

PROGRAMMING CALL TONES

Call Tones feature allows you to transmit an audible tone to other radios on the same channel to alert them that you are about to talk or to alert them without speaking.

In ‘Call Tone Selection Mode’ you can configure the type of call tone for the radio. The settings available are dependent on the maximum number of call tones your radio supports.

To program Call Tones, enter the Advanced Configuration Mode and scroll up or down through the programming modes until your display radio shows the ‘Programming Call Tones’ selection by short pressing the PTT button or (Menu) button.

The radio display shows the Programming Call Tone’ as follows:

The radio display blinks the current call tone setting. You can select the desired call tone value (0,1,2 or 3) by pressing the Programmable Button A and Programmable Button B buttons. Each time you select a different value, your radio sounds the selected call tone (except for value ‘0’). Once you have selected the desired call tone, long press the PTT button to exit and save, or short press the PTT button to move to the next programming feature without saving.

Note: The values available for Call Tones settings

are dependent on the values programmed via the CPS. Call Tones is disabled when the value is set to ‘0’.

PROGRAMMING MICROPHONE GAIN LEVEL

To configure the Microphone Gain Level, enter the Advanced Configuration Mode and scroll up or down

PROGRAMMING FEATURES

Page 42

English

PROGRAMMING FEATURES

through the programming modes by short pressing the PTT button or (Menu) button until you reach the ‘Microphone Gain Level Programming Mode’.

The radio display shows the Microphone Gain Level as follows:

The radio display blinks the current Microphone Gain Level setting. You can select the desired Microphone Gain Level (1 = low gain, 2 = medium gain or 3 = high gain) by pressing the Programmable Button A and Programmable Button B buttons.

Once you have selected the desired Microphone Gain Level, long press the PTT button to exit and save, or short press the PTT button to move to the next programming feature without saving.

Note: The values available for Microphone Gain

Level settings are dependent on the maximum Microphone Gain Level the radio supports.

PROGRAMMING MICROPHONE ACCESSORY GAIN LEVEL

To configure the Microphone Accessory Gain Level, enter the Advanced Configuration Mode and scroll up or down through the programming modes by short pressing the PTT button or (Menu) button.

The radio display shows the Microphone Accessory Gain Level as follows:

The radio blinks the current Microphone Accessory Gain Level setting. You can select the desired Microphone Accessory Gain Level (1 = low gain, 2 = medium gain or 3 = high gain) by pressing the Programmable Button A and Programmable Button B buttons.

Once you have selected the desired Microphone Gain Level, long press the PTT button to exit and save, or short press the PTT button to move to the next programming feature without saving.

Note: The values available for Microphone

Accessory Gain Level settings are

Page 43

English

dependent on the maximum Microphone Accessory Gain Level the radio supports.

OTHER PROGRAMMING FEATURES

Scan

Scan allows you to monitor other channels to detect conversations. When the radio detects a transmission, it stops scanning and goes to the active channel. This allows you to listen and talk to people in that channel without having to change channel manually. If there is talking going on Channel 2 during this time, the radio stays on Channel 1 and you will not hear Channel 2. After talking has stopped in Channel 1, the radio waits for 5 seconds before resuming scan again.

• To start scanning, press the SB1 or SB2 button. When the radio detects channel activity, it stops on that channel until activity on that channel ends. You can talk to the person(s) transmitting without having to switch channels by pressing the PTT button.

Note: Scan has to be programmed either to SB1

or SB2 button via CPS. SB2 is by default Scan/Nuisance Channel delete button. If Auto-Scan has been enabled for a particular channel, do not press SB1 or SB2

(programmed for scan) to start scanning, as the radio does it automatically.

• To stop scanning, short press the SB1 or SB2 button (programmed for scan) again.

• By pressing the PTT button while the radio is scanning, the radio will transmit on the channel which was previously selected before Scan is activated. If no transmission occurs within 5 seconds, scanning resumes.

• If you want to scan a channel without the Interference Eliminator Codes (CTCSS/DPL), set the code settings for the channels to ‘0’ in the CTCSS/DPL Programming Selection Mode.

Note: Whenever the radio is set to Scan, the LED

Indicator blinks a Red Heartbeat.

Programming Scan List

You can enable or disable the Channel Scanning feature for each channel in your radio. To do so, enter the Advanced Configuration Mode and select the channel you want to program. Scroll through the programming modes by short pressing the PTT button or (Menu) button until you reach the ‘Scan Programming Mode’.

PROGRAMMING FEATURES

Page 44

English

The radio display shows the Scan Programming Mode as follows:

Both the channel number and current scan setting (YES = Enable or NO = Disable) blinks on the display, indicating you can choose your setting. To set the channel number, rotate the Channel Selector Knob until you reach the desired channel number.

Once you have selected the channel, proceed to enable (‘YES’) or disable (‘NO’) the scan feature by pressing the SB2 (*) button. Once you have set the values you need, long press the PTT button to exit and save, or short press the PTT button to move to

PROGRAMMING FEATURES

the next programming feature without saving.

Note:

• (*) This assumes the SB2 button is not programmed for a different mode.

• If the Maximum Channel setting in the radio is set to ‘1’, the Scan Programming option is disabled and will not show on the radio display.

Programming Weather Channel (Not allowed on RDX4163)

Weather Channel Programming Mode is the last programming mode available. You can enable or disable the Weather Channel.

To do so, enter the Advanced Configuration Mode and select the channel you want to program. Scroll through the programming modes by short pressing the PTT button or (Menu) button until you reach the ‘Weather Channel Programming Mode’.

Press the Programmable Button A and Programmable Button B buttons to enable or disable the mode. Refer to “Weather Channel Frequencies Table” on page 47 for the frequency table.

Editing Channel Alias Name

To edit a Channel Alias Name, turn ON the radio and press and hold the PTT button simultaneously with the button for 3 seconds. The radio generate a special beep upon entering the ‘Channel Alias Mode’.

Page 45

English

The radio display shows the current channel alias name and channel number blinking as follows:

Choose the channel number you want to edit by rotating the Channel Selector Knob. Once you have selected the channel number, short press the PTT button or (Menu) button to start editing the channel alias name.

The character to be changed starts blinking. If it’s a blank character, a cursor starts blinking.

To change character, press the and buttons until the desired character is reached. To move to next character on the right, press the (Menu) button. The character sequence is [A-Z], “”, (Blank Space), [0-9] and Special Characters. No lower case is allowed.

Long press the PTT button to save and go back to the ‘Channel Alias Mode’ to choose other channel to edit the alias name or turn OFF the radio to exit without saving the changes

Note: If the channel alias name is left blank, long

pressing the PTT button does not save or leave the alias name.

Nuisance Channel Delete

Nuisance Channel Delete allows you to temporarily remove channels from the Scan List. This feature is useful when irrelevant conversations on a ‘nuisance’ channel ties up the radio’s scanning feature.

To delete a channel from the Scan List:

• Start Scan mode by short pressing the SB2(*) button.

• Wait until the radio stops at the channel you wish to eliminate. Long press the SB2 button to delete it. You cannot delete the channel with scan enabled (home channel).

• The channel will not be scanned again until you exit the Scan mode by short pressing the SB2 button again or by turning OFF the radio and back ON.

Note: (*) This assumes the SB2 button is not

programmed for a different mode.

PROGRAMMING FEATURES

Page 46

English

PROGRAMMING FEATURES

Drop-In Tray Charger Tray

Radio to be programmed

USB Ports

CPS Programming Cable

CUSTOMER PROGRAMMING SOFTWARE (CPS)

Figure 1: Setting up the radio to the CPS

The easiest way to program or change features in your radio is by using the Customer Programming Software (CPS) and the CPS Programming Cable(*). CPS Software is available for free as web based downloadable software at:

www.motorolasolutions.com/RDX

To program, connect the RM Series radio via the Drop-in Charger Tray and CPS Programming Cable as shown in Figure 1 on page 44. Toggle the cable

switch of the CPS Programming Cable to ‘CPS Mode’.

CPS allows you to program frequencies, PL/DPL Codes as well as other features such as: Bandwidth Select, Time-out Timer, Power Select, Scan List, Call Tones, Scramble, Reverse Burst, etc. CPS is a very useful tool as it can also lock the Front-Panel Radio Programming or restrict any specific radio feature to be changed (to avoid accidentally erasing the preset radio values). It also provides security by giving the option to set up a password for profile radio’s management. For more information, refer to Features Summary Chart Section at the end of the User Guide.

Note: (*) CPS Programming Cable P/N#

HKKN4027_ is an accessory sold separately. Please contact your Motorola point of purchase for more information.

Time-Out Timer

This timer sets the amount of time that the radio can continuously transmit before the transmission is automatically terminated. The default setting is 60 seconds and can be changed using the CPS.

Power Select

Power Select allows you to select between high and low transmission power per frequency in each

Page 47

English

channel. The High Power for RDX+ is 5 W for VHF and 4 W for UHF, Low Power for both bands is 2 W.

Note: Some frequencies may have FCC transmit

power restrictions that disallow them to be set at a higher power level. For more information, refer to the “Frequency and Code Charts” on page 63.

Call Tones

See “Programming Call Tones” on page 39.

Scramble

See “Programming Scramble” on page 38.

Reverse Burst

Reverse Burst eliminates unwanted noise (squelch tail) during loss of carrier detection. You can select values of either 180 or 240 to be compatible with other radios.

Note:

• The features described in previous pages are just some of the features CPS has. CPS offers more capabilities. For more information refer to the HELP file in the CPS.

• Some of the features available with the CPS

software may vary depending on the radio model.

PROGRAMMING FEATURES

TEXT-TO-SPEECH (CHANGING PREDEFINED VOICE ALIASES)

Enable User Pre-Defined Voice Prompt (VP) Checkbox

Check the box to enable user-defined voice on the selected channel. The user is given the option to either use the Text-to-Speech synthesizer in order to generate automated voice, or import a wave (.wav) file containing the voice data.

User Pre-Defined Voice Prompt (VP) Text

This field is used by the Text-to-Speech synthesizer embedded in the CPS to generate user-defined voice for the selected channel.

Note:

• The length of the string cannot exceed 18 characters.

• The string can only contain ISO-8859-1 characters.

Import Voice File

This field allows the user to upload a pre-existing wave (.wav) file from the local hard drive. The first

Page 48

English

eight characters of the wave files are used to populate the channel “Name”.

Note:

• The wave file must be sampled at 8 kHz.

• The wave file cannot exceed 65,000 kB in length.

Listen to User Customized Voice Prompt (VP) Text

This field allows the user to play the output voice signal generated from the Text-to-Speech synthesizer.

WEATHER FEATURE (NOT FOR RDU4163)

The RDX radio weather mode can be programmed to operate and receive weather channels that are broadcast by the National Weather Radio (NWR). The NWR system is a nationwide network of radio stations

PROGRAMMING FEATURES

(more than 1000 stations in United States) that broadcast continuous weather information for the public. The NWR broadcasts all types of weather service warnings, watches, forecasts and other hazard information. The NWR can also broadcast non- weather alerts such as national security, natural, environmental, and public safety in conjunctions with the Emergency Alert System (EAS).

The RDX radio weather feature can detect weather alerts/warnings that are broadcast by NWR. The RDX+ radio can be programmed to detect the analog tone or digital-over-audio protocol. The analog tone is a 1050 Hz tone (Warning Alarm Tone), which is issued for 10 seconds immediately before the warning message by the NWR transmitter. When RDX radio detects the Warning Alarm tone, it unmutes audio and allows the user to hear the weather alert message. As for digital-over- audio protocol, it is a newer technology called Specific Area Message Encoding (SAME) that allows weather radio to receive digital data stream about the type of weather events, timing, duration, and location. When RDX radio detects these special warnings, the radio can be programmed to automatically generate a loud tone, enable LED indicator, and display “hazard” status on the display. With the SAME technology, the RDX radio weather mode can be programmed to detect the type of weather warnings or watches for a specified the county or counties.

Further information about the National Weather Radio system such as network updates, transmitter coverage maps, and SAME event codes can be found on the Internet at www.nws.noaa.gov/nwr/.

Page 49

English

Weather Alert Mode

Select the alert mode the radio will respond to alerts sent from the National Weather Service, which transmitted prior to the broadcast of any message about a life or property threatening event.

Choices available are:

• OFF (Default): Disable the Weather Alert Feature.

• Tone Alert: Detect the Warning Alarm Tone (WAT).

• SAME Alert: Detect the Special Area Message Encoding (SAME).

Weather Channel Frequencies Table

Frequency Number Value (Mhz)

1 162.4000

2 162.4250

3 162.4500

Frequency Number Value (Mhz)

4 162.4750

5 162.5000

6 162.5250

7 162.5500

THE WEATHER ALERT HAS TWO MODES OF OPERATIONS

1. In Weather Channel Mode, the radio is in a

muted state until it detects the WAT/SAME. When the radio detects the WAT, the radio unmutes and allows the user to hear the weather alert message.

2. In two-way mode (on two-way channel),

Weather Alert feature becomes a special scan feature. The radio scans between the current selected two-way channel and the selected weather channel. When the radio detects WAT/ SAME signal on the weather channel, the radio

PROGRAMMING FEATURES

Page 50

English

unmutes to allow the user to listen the weather message. For Tone Alert, the radio stays in receiving mode until weather signal is weak or user presses the PTT button or changes the channel using the Channel Selector Knob. For SAME alert, whether the radio stays in receiving mode or switches back to two-way mode depending on the setting of the EOM Enabled.

Warning: RDX radio does not detect Weather Alert

while it is receiving or transmitting on a two-way channel.

EOM Enabled

This feature is only available for SAME Alert mode

PROGRAMMING FEATURES

and it is only effective when the radio operates in twoway mode or Weather Channel mode. When checked and in two-way mode, the radio switches back to twoway channel and continues to weather scan after it receives end of message (EOM). For weather channel, the radio mutes and continues to look for new SAME alert after it receives EOM. When unchecked, it stays in receiving mode until weather signal is weak or user presses the PTT button or

changes the channel using the Channel Selector Knob.

New Alert Tone Timer

Select a pre-defined time for a radio to play the new alert tone. When a radio receives a new SAME alert message, the LED screen lights up and the radio starts playing the new alert tone at the end of the message. Users have the ability to configure how long the alert tone will be played.

Choices available are:

• 0 – forever until a button is pressed, or user switches channel, or the new alert message is expired.

•5 min.

• 10 min.

• 30 min.

Note: Embedded in the SAME message is the

duration of the alert message. The RDX radio continues to display the alert until the duration expiration time.

EVENT TYPE FILTER

The RDX radio is a programmable weather radio that allows users to choose the type of weather warnings

Page 51

English

and watches that will alarm. The radio can be programmed to allow or block an event by its type.

All Events

When checked, the radio allows for all SAME events.

Alert Test Event

When SAME alert is enabled, the radio responds to any test events. When checked, the radio alerts the same way as other SAME alert messages. When unchecked, the radio displays only the Message, lights the alert LED without unmuting the radio. The radio does not play the new alert tone at this time.

Note: No matter how the user programs the event

filter, some critical events cannot be blocked. The National Weather Service broadcast a test alert every week on Wednesday between 11 AM and Noon. Users should use test alert to ensure that their radios are functioning properly. See also: The Critical Events Table.

WARNING

When checked, the radio allows all warning events. Warning events are events that alone pose a significant threat to public safety and/or property.

Note: No matter how the user programs the event

filter, some critical events cannot be blocked. See also: The Critical Events Table.

WATCH

When checked, the radio allows all watch events. Watches are events that meet the classification of a warning, but either the onset time, probability of occurrence or location is uncertain.

Note: No matter how the user programs the event

filter, some critical events cannot be blocked. See also: The Critical Events Table.

EMERGENCY

When checked, the radio allows all emergency events. Emergency event is an event that by itself would not kill or injure or do property damage, but indirectly may cause other things to happen that result in a hazard.

Note: No matter how the user programs the event

filter, some critical events cannot be blocked. See also: The Critical Events Table.

PROGRAMMING FEATURES

Page 52

English

STATEMENT

When checked, the radio allows all statement events. Statement is message that contains follow-up information to a warning, watch, or emergency.

Note: No matter how the user programs the event

filter, some critical events cannot be blocked. See also: The Critical Events Table.

EVENT CODE FILTER

A specific SAME event can be allowed or blocked. There are maximum of five Event Codes can be programmed.

BLOCK EVENT

When checked, the Event Codes entered below shall be blocked.

PROGRAMMING FEATURES

Note: No matter how the user programs the event

filter, some critical events cannot be blocked. See also: The Critical Events Table.

EVENT CODE

The Event Code field accepts wild card (“*”). The following are examples of valid Event Code format.

• “***” - all events

• FL"*” – FLA or FLW

•FLA

The “blank” means unprogrammed and the radio will bypass it without doing anything.

Note: No matter how the user programs the event

filter, some critical events cannot be blocked. See also: The Critical Events Table.

THE CRITICAL EVENTS TABLE

Abbreviation Description

BHW

Biological Hazard

Warning

CDW Civil Danger Warning

CEM

Civil Emergency

Message

Page 53

English

Abbreviation Description

CHW

Chemical Hazard

Warning

Abbreviation Description

FCW

Food Contamination

Warning

PROGRAMMING FEATURES

CWW

DBW Dam Break Warning

DEW

EAN

EAT

EQW Earthquake Warning

EVI

Contaminated Water

Warning

Contagious Disease

Warning

Emergency Action

Notification

Emergency Action

Termination

Evacuation

Immediate

HMW

HUW Hurricane Warning

IEW

IFW

LAE

LEW

LSW Land Slide Warning

Hazardous Materials

Warning

Immediate

Evacuation Warning

Industrial Fire

Warning

Local Area

Emergency

Law Enforcement

Warning

Page 54

English

Abbreviation Description

PROGRAMMING FEATURES

NHW

NUW

RHW

SPW

National Hazard

Warning

Nuclear Power Plant

Warning

Radiological Hazard

Warning

Shelter In Place

Warning

TOR Tornado Warning

TOW Tornado Warning

TRW

Tropical Storm

Warning

TSA Tsunami Watch

TSW Tsunami Warning

VOW Volcano Warning

WFW Wild Fire Warning

GEOGRAPHIC FILTER

There are maximum of six geographic codes can be programmed. When all fields are unselected, or any of the geographic code is “ALL” for both State and County code (FIPS is “000000”), the radio bypasses the Geographic Filter check.

There are two ways to enter the geographic code,

• Select State and County Code.

• Enter the FIPS code directly (must be 6 digits).

STATE

Selects the State, Territory and Offshore (Marine Area) portion (SS) the radio alerts for.

COUNTY

Select a county, province, or major metropolitan area (CCC) the radio alerts for.

Page 55

English

FIPS

Pocket 1

“CLONE” symbol

Pocket 2 “CLONE” symbol Pocket 5

Pocket 4

Federal Information Processing Standards (FIPS) contains six digits which represent PSSCCC, where P is the region code, SS is the state code and CCC is the county code.

Enters/Edits a specific FIPS whenever it is necessary. Further information about FIPS can be found on the

Internet at www.nws.noaa.gov/nwr/ indexnw.htm or call the National Weather Service Toll-Free Number SAME county code – 1888-NWS-SAME (1-888-697-

7263).

CLONING RADIOS

You can clone RDX Series radio profiles from one Source radio to a Target radio by using any one of these three methods:

• Using a Multi Unit Charger (MUC- optional

• Using two Single Unit Chargers (SUC) and a

• the CPS (free software download)

Cloning with a Multi Unit Charger (MUC)

To clone radios using the MUC, there must be at least two radios:

• a Source radio (the radio which profiles will be cloned or copied from) and

• a Target radio (the radio which profile will be

accessory),

Radio-to-Radio cloning cable (optional accessory),

cloned from the source radio.)

The Source radio has to be in Pocket 1, 3 or 5 while the Target radio has to be in Pocket 2, 4 or 6, matching in the MUCs pockets by pairs as follows:

• 1 and 2 or,

• 3 and 4 or,

• 5 and 6 (*).

PROGRAMMING FEATURES

Page 56

English

When cloning, the MUC does not need to be plugged into a power source, but ALL radios require charged batteries.

1. Turn ON the Target radio and place it into one of

the MUC Target Pockets

2. Power the Source radio following the sequence

below:

• Long Press the PTT button and SB2 simultaneously while turning the radio ON.

• Wait for 3 seconds before releasing the buttons until the audible tone “Cloning” is heard.

3. Place the Source radio in the source pocket that

PROGRAMMING FEATURES

pairs with the target pocket you chose in step 1. Press and release the SB1 button.

4. After cloning is completed, the Source radio will

announce either “successful” (cloning is successful) or “fail” (cloning has failed). The ‘successful’ tone sounds like a good key ‘chirp’ whereas the ‘fail’ tone sounds similar to a ‘bonk’ tone. If the Source radio is a display model, it

will either show ‘Pass’ or ‘Fail’ on the display (a tone will be heard within 5 s).

5. Once you have completed the cloning process,

turn the radios OFF and ON or, long press the PTT button to exit the ‘cloning’ mode.

Further details on how to clone radios are explained in the Instructions Sheet provided with the MUC.

When ordering the MUC, refer to part number RLN6309_.

Note:

• If cloning fails, refer to “What To Do If Cloning Fails” on page 56.

• Paired Target radios and Source radios must be of the same band type in order for the cloning to run successfully.

• MUC pockets numbers should be read from left to right with the Motorola logo facing front.

Page 57

English

Cloning Radio using the Radio to Radio (R2R) Cloning Cable (Optional Accessory)

Operating Instructions

1. Before starting the cloning process, make sure

you have:

• A fully charged battery on each of the radios.

• Two Single-Unit Chargers (SUC).

• Turn OFF the radios and,

• Both radios are of the same radio model.

2. Unplug any cables (power supply or USB

cables) from the SUCs.

3. Plug one side of the cloning cable mini USB

connector to the first SUC and the other end to the second SUC.

Note: During the cloning process, no power is

being applied to the SUC. The batteries will not be charged. Only data communication is being established between the two radios.

4. Turn ON the Target Radio and place it into one

of the SUCs.

5. For the Source Radio, power ON the radio with

the following sequence:

• Long press the PTT button and SB2 simultaneously while turning the radio ON.

• Wait for 3 s before releasing the buttons until a distinctive audible tone is heard.

6. Place the Source radio in its SUC, press and

release SB1.

7. After cloning is completed, the Source radio will

sound either a ‘pass’ tone (cloning was successful) or a ‘fail’ tone (cloning process has failed). The ‘pass’ tone sounds like a good key

PROGRAMMING FEATURES

Page 58

English

‘chirp’ whereas the ‘fail’ tone sounds similar to a ‘bonk’ tone. If the Source radio is a display model, it will either show ‘Pass’ or ‘Fail’ on the display (a tone will be heard within 5 seconds).

8. Once you have completed the cloning process,

turn the radios OFF and ON to exit ‘clone’ mode.

What To Do If Cloning Fails

The radio will emit an audible “bonk” indicating that the cloning process has failed. In the event that the cloning fails, perform each of the following steps before attempting to start cloning process again:

1. Ensure that the batteries on both radios are fully

charged.

2. Check the cloning cable connection on both

PROGRAMMING FEATURES

SUCs.

3. Ensure that the battery is engaged properly on

the radio.

4. Ensure that there is no debris in the charging

tray or on the radio contacts.

5. Ensure that the Target radio is turned ON.

6. Ensure that the Source radio is in cloning mode.

7. Ensure that the two radios are both from the

same frequency band, same region and have the same transmission power.

Note: This cloning cable is designed to operate

only with compatible Motorola SUC RLN6175_ and RLN6304_.

When ordering Optional Cloning Cable, please refer to part number RLN6303_. For more information about the accessories, refer to “Accessories” on page 75.

Page 59

English

Drop-In Tray Charger Tray

Radio to be programmed

USB Ports

CPS Programming Cable

Cloning using the Customer Programming Software (CPS)

When cloning using this method, you need the CPS software, a Drop-In Tray Charger and the CPS Programming Cable.

To order the CPS Programming Cable, please refer to part number RKN4155_.

Information on how to clone using the CPS is available either in:

• the CPS Help File --> Content and Index --> Cloning Radios, or

• in the CPS Programming Cable Accessory Leaflet.

PROGRAMMING FEATURES

Page 60

English

TROUBLESHOOTING

Symptom Try This...

No Power

Hearing other noises or conversation on a channel

TROUBLESHOOTING

Message Scrambled

Recharge or replace the Li-Ion battery. Extreme operating temperatures may affect battery life. Refer to “About the Li-Ion Battery” on page 15.

Confirm Interference Eliminator Code is set. Frequency or Interference Eliminator Code may be in use. Change settings: either change frequencies or codes on all radios. Make sure radio is at the right frequency and code when transmitting. Refer to “Talking and Monitoring” on page 29.

Scramble Code might be ON, and/or setting does not match the other radios' settings.

Audio quality not good enough

Radio settings might not be matching up correctly. Double check frequencies, codes and bandwidths to make sure they are identical in all radios.

Page 61

English

Symptom Try This...

Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease range. Check for clear line of sight to improve transmission. Wearing radio close to body such as in a pocket or on a belt decreases range.

Limited talk range

Message not transmitted or received

Change location of radio. To increase range and coverage, you can reduce obstructions or increase power. UHF radios provides greater coverage in industrial and commercial buildings. Increasing power provides greater signal range and increased penetration through obstructions. Refer to “Talking and Monitoring” on page 29.

Make sure the PTT button is completely pressed when transmitting. Confirm that the radios have the same Channel, Frequency, Interference Eliminator Code and Scramble Code settings. Refer to “Talking and Monitoring” on page 29 for further information. Recharge, replace and/or reposition batteries. Refer to “About the Li-Ion Battery” on page 15. Obstructions and operating indoors, or in vehicles, may interfere. Change location. Refer to “Talking and Monitoring” on page 29. Verify that the radio is not in Scan. Refer to “Scan” on page 41 and “Nuisance Channel Delete” on page 43.

TROUBLESHOOTING

Page 62

English

Symptom Try This...

Heavy static or interference

Low batteries

Drop-in Charger LED light does not blink

TROUBLESHOOTING

Low battery indicator is blinking although new batteries are inserted

Radios are too close; they must be at least five feet apart. Radios are too far apart or obstacles are interfering with transmission. Refer to “Talking and Monitoring” on page 29.

Recharge or replace Li-Ion battery. Extreme operating temperatures affect battery life. Refer to “About the Li-Ion Battery” on page 15.

Check that the radio/battery is properly inserted and check the battery/charger contacts to ensure that they are clean and charging pin is inserted correctly. Refer to “Charging the Battery” on page 21, “Drop-in Tray Charger LED Indicators” on page 23 and “Installing the Lithium-Ion (Li-Ion) Battery” on page 17.

Refer to “Installing the Lithium-Ion (Li-Ion) Battery” on page 17, and “About the Li-Ion Battery” on page 15.

Page 63

English

Symptom Try This...

VOX feature might be set to OFF.

Cannot activate VOX

Battery does not charge although it has been placed in the drop-in charger for a while

Use the CPS to ensure that the VOX Sensitivity level is not set to ‘0’. Accessory not working or not compatible. Refer to “Hands-Free Use/VOX” on page 32.

Check drop-in tray charger is properly connected and correspond to a compatible power supply. Refer to “Charging with the Drop-in Tray Single Unit Charger (SUC)” on page 21 and “Charging A Stand-Alone Battery” on page 22. Check the charger’s LEDs indicators to see if the battery has a problem. Refer to “Drop-in Tray Charger LED Indicators” on page 23.

TROUBLESHOOTING

User voice prompt does not clone.

Note: Whenever a feature in the radio seems to not correspond to the default or preprogrammed values,

check to see if the radio has been programmed using the CPS with a customized profile.

Check the front radio name plate. Radios with an orange color font will not support customize voice prompt.

Page 64

English

USE AND CARE

Use a soft damp cloth to clean the exterior

Do not immerse in water

Do not use alcohol or cleaning solutions

If the radio is submerged in water...

Turn radio OFF and remove batteries

Dry with soft cloth

Do not use radio until completely dry

USE AND CARE

Page 65

English

FREQUENCY AND CODE CHARTS

RDX UHF FREQUENCIES CHART

The charts in this section provide Frequency and Code information. These charts are useful

RDX UHF 16CH Radios Default Frequencies – RDU4163

Channel Frequency #

1 1 458.6625 1 67.0 Hz 12.5 kHz

2 2 469.2625 1 67.0 Hz 12.5 kHz

3 1 458.6625 2 71.9 Hz 12.5 kHz

4 2 469.2625 2 71.9 Hz 12.5 kHz

5 1 458.6625 3 74.4 Hz 12.5 kHz

6 2 469.2625 3 74.4 Hz 12.5 kHz

7 1 458.6625 4 77.0 Hz 12.5 kHz

8 2 469.2625 4 77.0 Hz 12.5 kHz

9 1 458.6625 5 79.7 Hz 12.5 kHz

10 2 469.2625 5 79.7 Hz 12.5 kHz

Frequency

(MHz)

when using the Motorola Solutions RDX Series two-way radios with other business radios.

FREQUENCY AND CODE

RDU4163 – UHF DEFAULT FREQUENCIES CHART

CHARTS

Code# Code Bandwidth

Page 66

English

CHARTS

FREQUENCY AND CODE

RDX UHF 16CH Radios Default Frequencies – RDU4163

11 1 458.6625 6 82.5 Hz 12.5 kHz

12 2 469.2625 6 82.5 Hz 12.5 kHz

13 1 458.6625 7 85.4 Hz 12.5 kHz

14 2 469.2625 7 85.4 Hz 12.5 kHz

15 1 458.6625 8 88.5 Hz 12.5 kHz

16 2 469.2625 8 88.5 Hz 12.5 kHz

Page 67

English

RDX UHF FREQUENCIES CHART

RDX UHF Frequencies

Frequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth

1 464.5000 12.5 kHz 15 461.1875 12.5 kHz

2 464.5500 12.5 kHz 16 461.2125 12.5 kHz *3 467.7625 12.5 kHz 17 461.2375 12.5 kHz *4 467.8125 12.5 kHz 18 461.2625 12.5 kHz *5 467.8500 12.5 kHz 19 461.2875 12.5 kHz *6 467.8750 12.5 kHz 20 461.3125 12.5 kHz *7 467.9000 12.5 kHz 21 461.3375 12.5 kHz *8 467.9250 12.5 kHz 22 461.3625 12.5 kHz

9 461.0375 12.5 kHz *23 462.7625 12.5 kHz 10 461.0625 12.5 kHz *24 462.7875 12.5 kHz 11 461.0875 12.5 kHz *25 462.8125 12.5 kHz 12 461.1125 12.5 kHz *26 462.8375 12.5 kHz 13 461.1375 12.5 kHz *27 462.8625 12.5 kHz 14 461.1625 12.5 kHz *28 462.8875 12.5 kHz

FREQUENCY AND CODE

CHARTS

Page 68

English

RDX UHF Frequencies (Continued)

Frequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth

*29 462.9125 12.5 kHz 47 466.3625 12.5 kHz

30 464.4875 12.5 kHz *48 467.7875 12.5 kHz 31 464.5125 12.5 kHz *49 467.8375 12.5 kHz 32 464.5375 12.5 kHz *50 467.8625 12.5 kHz 33 464.5625 12.5 kHz *51 467.8875 12.5 kHz 34 466.0375 12.5 kHz *52 467.9125 12.5 kHz

CHARTS

FREQUENCY AND CODE

35 466.0625 12.5 kHz 53 469.4875 12.5 kHz 36 466.0875 12.5 kHz 54 469.5125 12.5 kHz 37 466.1125 12.5 kHz 55 469.5375 12.5 kHz 38 466.1375 12.5 kHz 56 469.5625 12.5 kHz 39 466.1625 12.5 kHz 57 462.1875 12.5 kHz 40 466.1875 12.5 kHz 58 462.4625 12.5 kHz 41 466.2125 12.5 kHz 59 462.4875 12.5 kHz 42 466.2375 12.5 kHz 60 462.5125 12.5 kHz 43 466.2625 12.5 kHz 61 467.1875 12.5 kHz 44 466.2875 12.5 kHz 62 467.4625 12.5 kHz 45 466.3125 12.5 kHz 63 467.4875 12.5 kHz 46 466.3375 12.5 kHz 64 467.5125 12.5 kHz

Page 69

English

RDX UHF Frequencies (Continued)

Frequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth

65 451.1875 12.5 kHz 82 456.4375 12.5 kHz 66 451.2375 12.5 kHz 83 456.5375 12.5 kHz 67 451.2875 12.5 kHz 84 456.6375 12.5 kHz 68 451.3375 12.5 kHz 85 457.3125 12.5 kHz 69 451.4375 12.5 kHz 86 457.4125 12.5 kHz 70 451.5375 12.5 kHz 87 457.5125 12.5 kHz 71 451.6375 12.5 kHz 88 457.7625 12.5 kHz 72 452.3125 12.5 kHz 89 457.8625 12.5 kHz 73 452.5375 12.5 kHz 90 468.2125 12.5 kHz 74 452.4125 12.5 kHz 91 468.2625 12.5 kHz 75 452.5125 12.5 kHz 92 468.3125 12.5 kHz 76 452.7625 12.5 kHz 93 468.3625 12.5 kHz 77 452.8625 12.5 kHz 94 468.4125 12.5 kHz 78 456.1875 12.5 kHz 95 468.4625 12.5 kHz 79 456.2375 12.5 kHz 96 468.5125 12.5 kHz 80 456.2875 12.5 kHz 97 468.5625 12.5 kHz 81 456.3375 12.5 kHz 98 468.6125 12.5 kHz 82 456.4375 12.5 kHz 99 468.6625 12.5 kHz

Note: (*) Frequency limited to 2 W maximum power

output.

FREQUENCY AND CODE

CHARTS

Page 70

English

RDU4160 – UHF DEFAULT FREQUENCIES CHART

Channel Frequency #

1 1 464.5000 1 67.0 Hz 12.5 kHz

2 1 464.5000 4 77.0 Hz 12.5 kHz

3 1 464.5000 8 88.5 Hz 12.5 kHz

CHARTS

FREQUENCY AND CODE

4 1 464.5000 29 179.9 Hz 12.5 kHz

5 1 464.5000 0 - 12.5 kHz

6 2 464.5500 1 67.0 Hz 12.5 kHz

7 2 464.5500 6 82.5 Hz 12.5 kHz

8 WC 162.4000 10 67.0 Hz 25.0 kHz

9 2 464.5500 29 179.9 Hz 12.5 kHz

10 2 464.5500 0 - 12.5 kHz

11 22 461.3625 3 74.4 Hz 12.5 kHz

12 30 462.4875 5 79.7 Hz 12.5 kHz

13 32 462.5375 7 85.4 Hz 12.5 kHz

RDX UHF 16CH Radios Default Frequencies – RDU4160

Frequency

(MHz)

Code # Code Bandwidth

Page 71

English

RDX UHF 16CH Radios Default Frequencies – RDU4160

14 34 462.0375 9 91.5 Hz 12.5 kHz

15 36 464.0875 11 97.4 Hz 12.5 kHz

16 38 464.1375 13 103.5 Hz 12.5 kHz

Note: WC = Weather Channel Frequency

PROGRAMMING CUSTOMIZED FREQUENCIES ON RDU4160

4 W Models can be programmed to have customized frequencies (different from the ones shown in the UHF charts in previous pages). UHF range is 438 – 470 MHz.

4 W models can also be programmed to work with repeaters. Please contact your Motorola Solutions point of purchase for details.

FREQUENCY AND CODE

CHARTS

Page 72

English

CTCSS AND PL/DPL CODES

CTCSS Hz CTCSS Hz CTCSS Hz

1 67.0 14 107.2 27 167.9

2 71.9 15 11 0.9 28 173.8

3 74.4 16 114.8 29 179.9

4 77.0 17 11 8.8 30 186.2

5 79.7 18 123 31 192.8

CHARTS

FREQUENCY AND CODE

6 82.5 19 127.3 32 203.5

7 85.4 20 131.8 33 210.7

8 88.5 21 136.5 34 218.1

9 91.5 22 141.3 35 225.7

10 94.8 23 146.2 36 233.6

11 97.4 24 151.4 37 241.8

12 100.0 25 156.7 38 250.3

13 103.5 26 162.2 122 (*) 69.3

Note: (*) New CTCSS code.

CTCSS Codes

Page 73

English

PL/DPL Codes

DPL Code DPL Code DPL Code

39 23 55 116 71 243

40 25 56 125 72 244

41 26 57 131 73 245

42 31 58 132 74 251

43 32 59 134 75 261

44 43 60 143 76 263

45 47 61 152 77 265

46 51 62 155 78 271

47 54 63 156 79 306

48 65 64 162 80 311

49 71 65 165 81 315

50 72 66 172 82 331

51 73 67 174 83 343

52 74 68 205 84 346

53 114 69 223 85 351

54 115 70 226 86 364

FREQUENCY AND CODE

CHARTS

Page 74

English

CHARTS

FREQUENCY AND CODE

PL/DPL Codes (Continued)

DPL Code DPL Code DPL Code

87 365 104 565 121 754

88 371 105 606 123 645

89 411

90 412 107 624 125 Customized PL

91 413 108 627 126 Customized PL

92 423 109 631 127 Customized PL

93 431 11 0 632 128 Customized PL

94 432 111 654 129 Customized PL

95 445 11 2 662 130 Inverted DPL 39

96 464 11 3 664 131 Inverted DPL 40

97 465 11 4 703 132 Inverted DPL 41

98 466 11 5 712 133 Inverted DPL 42

99 503 11 6 723 134 Inverted DPL 43

100 506 11 7 731 135 Inverted DPL 44

101 516 11 8 732 136 Inverted DPL 45

102 532 11 9 734 137 Inverted DPL 46

103 546 120 743 138 Inverted DPL 47

106 612 124 Customized PL

Page 75

English

PL/DPL Codes (Continued)

DPL Code DPL Code DPL Code

139 Inverted DPL 48 156 Inverted DPL 65 173 Inverted DPL 82

140 Inverted DPL 49 157 Inverted DPL 66 174 Inverted DPL 83

141 Inverted DPL 50 158 Inverted DPL 67 175 Inverted DPL 84

142 Inverted DPL 51 159 Inverted DPL 68 176 Inverted DPL 85

143 Inverted DPL 52 160 Inverted DPL 69 177 Inverted DPL 86

144 Inverted DPL 53 161 Inverted DPL 70 178 Inverted DPL 87

145 Inverted DPL 54 162 Inverted DPL 71 179 Inverted DPL 88

146 Inverted DPL 55 163 Inverted DPL 72 180 Inverted DPL 89

147 Inverted DPL 56 164 Inverted DPL 73 181 Inverted DPL 90

148 Inverted DPL 57 165 Inverted DPL 74 182 Inverted DPL 91

149 Inverted DPL 58 166 Inverted DPL 75 183 Inverted DPL 92

150 Inverted DPL 59 167 Inverted DPL 76 184 Inverted DPL 93

151 Inverted DPL 60 168 Inverted DPL 77 185 Inverted DPL 94

152 Inverted DPL 61 169 Inverted DPL 78 186 Inverted DPL 95

153 Inverted DPL 62 170 Inverted DPL 79 187 Inverted DPL 96

154 Inverted DPL 63 171 Inverted DPL 80 188 Inverted DPL 97

155 Inverted DPL 64 172 Inverted DPL 81 189 Inverted DPL 98

FREQUENCY AND CODE

CHARTS

Page 76

English

CHARTS

FREQUENCY AND CODE

PL/DPL Codes (Continued)

DPL Code DPL Code DPL Code

190 Inverted DPL 99 200 Inverted DPL 109 210 Inverted DPL 119

191 Inverted DPL 100 201 Inverted DPL 110 211 Inverted DPL 120

192 Inverted DPL 101 202 Inverted DPL 111 212 Inverted DPL 121

193 Inverted DPL 102 203 Inverted DPL 112 213 Inverted DPL 123

194 Inverted DPL 103 204 Inverted DPL 113 214 Customized DPL

195 Inverted DPL 104 205 Inverted DPL 114 215 Customized DPL

196 Inverted DPL 105 206 Inverted DPL 115 216 Customized DPL

197 Inverted DPL 106 207 Inverted DPL 116 217 Customized DPL

198 Inverted DPL 107 208 Inverted DPL 117 218 Customized DPL

199 Inverted DPL 108 209 Inverted DPL 118 219 Customized DPL

Page 77

English

ACCESSORIES

Part No. Description

ANTENNA

Part No. Description

RAN4031

RAN4033

AUDIO ACCESSORIES

Part No. Description

HKLN4601 Surveillance Earpiece BR

53815 Headset w/Boom Mic BR

HMN4606 Remote Speaker Mic BR

53865 Headset w/Swivel Boom Mic

UHF Whip Antenna 438–470 MHz

UHF Stubby Antenna 438–470 MHz

HKLN4599 Earpiece w/Inline Mic Swivel

HKLN4604 Earpiece BR

BATTERY

Part No. Description

RLN6308 High Capacity Li-Ion Battery

RLN6351 Standard Li-ion Battery

CABLES

Part No. Description

RLN6303 Radio to Radio Cloning Cable

RKN4155 CPS Programming Cable

ACCESSORIES

Page 78

English

CHARGERS

SOFTWARE APPLICATIONS

ACCESSORIES

Part No. Description

RLN6304

RLN6309

RLN6175 Standard Drop-in Tray Charger

Rapid ACCY Charging Kit Americas (*)

Multi Unit Charger (MUC) Kit North America

CARRY ACCESSORIES

Part No. Description

RLN6302 Leather Carry Case

RLN6307 Spring Action Belt Clip

Part No. Description

RVN5147

Customer Programming Software (CPS)

POWER SUPPLIES AC PIN ADAPTERS

Part No. Description

RLN6349 North America AC Pin Adapter

POWER SUPPLIES

Part No. Description

RPN4054

RPN4058

PMPN4005 Rapid Exchg AC pin Pwr Supply

Standard US Fixed Power Supply

Standard Exchg AC pin Pwr Supply

Page 79

English

MOTOROLA SOLUTIONS LIMITED WARRANTY FOR THE UNITED STATES AND CANADA

What Does this Warranty Cover?

Subject to the exclusions contained below, Motorola Solutions, Inc. warrants its telephones, pagers, and consumer and business two-way radios (excluding commercial, government or industrial radios) that operate via Family Radio Service or General Mobile Radio Service, Motorola Solutions-branded or certified accessories sold for use with these Products (“Accessories”) and Motorola Solutions software contained on CD-ROMs or other tangible media and sold for use with these Products (“Software”) to be free from defects in materials and workmanship under normal consumer usage for the period(s) outlined below. This limited warranty is a consumer's exclusive remedy, and applies as follows to new Motorola Solutions Products, Accessories and Software purchased by consumers in the United States, which are accompanied by this written warranty.

Products and Accessories

Products Covered Length of Coverage

Products and Accessories as defined

above, unless otherwise provided for below.

Decorative Accessories and Cases.

Decorative covers, bezels, PhoneWrap™ covers and cases.

Business Two-way Radio Accessories

Products and Accessories that are Repaired or Replaced.

One (1) year from the date

of purchase by the first consumer purchaser of the product unless otherwise provided for below.

Limited lifetime warranty for the lifetime of ownership by the first consumer purchaser of the product.

One (1) year from the date of purchase by the first consumer purchaser of the product.

The balance of the original warranty or for ninety (90) days from the date returned

to the consumer, whichever is longer.

MOTOROLA SOLUTIONS LIMITED

WARRANTY FOR THE UNITED

STATES AND CANADA

Page 80

English

Exclusions

Normal Wear and Tear. Periodic maintenance, repair

and replacement of parts due to normal wear and tear are excluded from coverage. Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty. Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of the product resulting from misuse; (b) contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; (c) use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or

STATES AND CANADA

conditions; or (d) other acts which are not the fault of Motorola Solutions, are excluded from coverage.

Use of Non-Motorola Solutions Products and

WARRANTY FOR THE UNITED

Accessories. Defects or damage that result from the

MOTOROLA SOLUTIONS LIMITED

use of Non-Motorola Solutions branded or certified Products, Accessories, Software or other peripheral equipment are excluded from coverage. Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, or modification in any way by someone other than Motorola Solutions, or its authorized service centers, are excluded from coverage.

Altered Products. Products or Accessories with (a) serial numbers or date tags that have been removed, altered or obliterated; (b) broken seals or that show evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming or non-Motorola Solutions housings, or parts, are excluded form coverage. Communication Services. Defects, damages, or the failure of Products, Accessories or Software due to any communication service or signal you may subscribe to or use with the Products Accessories or Software is excluded from coverage.

Software

Products Covered Length of Coverage

Software. Applies only

to physical defects in the media that embodies the copy of the software (e.g. CDROM, or floppy disk).

Ninety (90) days from the date of purchase.

Exclusions

Software Embodied in Physical Media. No warranty

is made that the software will meet your requirements or will work in combination with any hardware or software applications provided by third parties, that the operation of the software products will be

Page 81

English

uninterrupted or error free, or that all defects in the software products will be corrected. Software NOT Embodied in Physical Media. Software that is not embodied in physical media (e.g. software that is downloaded from the internet), is provided “as is” and without warranty.

WHO IS COVERED?

This warranty extends only to the first consumer purchaser, and is not transferable.

HOW TO OBTAIN WARRANTY SERVICE OR OTHER INFORMATION?

Contact your Motorola point of purchase.

SOFTWARE COPYRIGHT NOTICE

The Motorola Solutions products described in this manual may include copyrighted Motorola Solutions and third party software stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola Solutions and third party software providers certain exclusive rights for copyrighted software, such as the exclusive rights to distribute or reproduce the copyrighted software. Accordingly, any copyrighted software contained in the Motorola Solutions products may not be modified, reverse-engineered, distributed, or reproduced in any manner to the extent allowed by law.

Furthermore, the purchase of the Motorola Solutions products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents, or patent applications of Motorola Solutions or any third party software provider, except for the normal, non-exclusive, royaltyfree license to use that arises by operation of law in the sale of a product.

PATENT NOTICE

This product is covered by one or more of the following United States patents. 5896277 5894292 5864752 5699006 5742484 D408396 D399821 D387758 D389158 5894592 5893027 5789098 5734975 5861850 D395882 D383745 D389827 D389139 5929825 5926514 5953640 6071640 D413022 D416252 D416893 D433001

EXPORT LAW ASSURANCES

This product is controlled under the export regulations of the United States of America. The Governments of the United States of America may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S. Department of Commerce.

MOTOROLA SOLUTIONS LIMITED

WARRANTY FOR THE UNITED

STATES AND CANADA

Page 82

Français (Canada)

TABLE DES MATIÈRES

Table des matières . . . . . . . . . . . . . . . . . . . .1

Sécurité du produit . . . . . . . . . . . . . . . . . . . .5

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .6

Contenu de l'emballage. . . . . . . . . . . . . . . . . .6

Renseignements de licence FCC. . . . . . . . .7

Informations relatives aux interférences . . . . .7

Renseignements relatifs aux licences

canadiennes. . . . . . . . . . . . . . . . . . . . . . . . . .9

Information générale . . . . . . . . . . . . . . . . . . . .9

Demande de licence . . . . . . . . . . . . . . . . . . . .9

Renseignements sur l'utilisation sécuritaire des batteries et des

chargeurs. . . . . . . . . . . . . . . . . . . . . . . . . . .11

TABLE DES MATIÈRES

Directives d'utilisation sécuritaire . . . . . . . . .12

Présentation de la radio . . . . . . . . . . . . . . .13

Parties de la radio . . . . . . . . . . . . . . . . . . . . .13

Bouton Marche/Arrêt/Volume . . . . . . . . .14

Bouton sélecteur de canal . . . . . . . . . . .14

Connecteur accessoire . . . . . . . . . . . . . .14

Étiquette du modèle . . . . . . . . . . . . . . . .14

Microphone . . . . . . . . . . . . . . . . . . . . . . .14

Antenne . . . . . . . . . . . . . . . . . . . . . . . . . 14

Voyant lumineux . . . . . . . . . . . . . . . . . . 14

Boutons avant . . . . . . . . . . . . . . . . . . . . 14

Boutons latéraux . . . . . . . . . . . . . . . . . . . . . 15

Batterie au lithium-ion (Li-Ion) . . . . . . . . 15

Caractéristiques de la batterie . . . . . . . . . . . 16

À propos de la batterie lithium-ion . . . . . 16

Recyclage et mise au rebut des

batteries . . . . . . . . . . . . . . . . . . . . . . . 17

Installation de la batterie au lithium-ion (Li-

Ion). . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Retrait de la batterie au lithium-ion

(Li-Ion). . . . . . . . . . . . . . . . . . . . . . . . 18

Installation de l'antenne . . . . . . . . . . . . . 19

Retrait de l'antenne . . . . . . . . . . . . . . . . 19

Installation de la pince de ceinture à

ressort . . . . . . . . . . . . . . . . . . . . . . . . 20

Bloc d'alimentation, adaptateur et

chargeur instantané . . . . . . . . . . . . . . 20

Information sur l'autonomie de la

batterie. . . . . . . . . . . . . . . . . . . . . . . . 21

Charge de la batterie . . . . . . . . . . . . . . . 22

Voyants DEL du chargeur instantané . . 24

Page 83

Français (Canada)

Durée de charge estimée . . . . . . . . . . . .26

Voyants DEL du chargeur multi-unités . .28

Pour commencer . . . . . . . . . . . . . . . . . . . . .29

Mise sous tension et hors tension

de la radio. . . . . . . . . . . . . . . . . . . . . . . . . .29

Réglage du volume . . . . . . . . . . . . . . . . . . . .29

LECTURE DE L’AFFICHAGE . . . . . . . . . . . .29

Sélection d'un canal . . . . . . . . . . . . . . . . . . .29

Conversation et contrôle . . . . . . . . . . . . . . . .30

Recevoir un appel . . . . . . . . . . . . . . . . . . . . .30

Indicateurs d’intensité du signal

et de canal occupé . . . . . . . . . . . . . . . . . . .30

Portée de communication . . . . . . . . . . . . . . .31

Voyants DEL de la radio . . . . . . . . . . . . . . . .33

Utilisation en mains libres/VOX . . . . . . . . . . .34

Avec accessoires VOX compatibles . . . .34

Activation du message vocal en mode

utilisateur . . . . . . . . . . . . . . . . . . . . . . . . . .35

Mode de tonalité de mise sous tension. . . . .35

Réinitialisation des paramètres par défaut . .35

Bips du clavier. . . . . . . . . . . . . . . . . . . . . . . .35

Verrouillage et déverrouillage du clavier . . . .36

Options de menu. . . . . . . . . . . . . . . . . . . . . .36

Réglage de la sensibilité VOX/iVOX . . . . . . 36

Gain du microphone. . . . . . . . . . . . . . . . . . . 37

Fonctions de programmation . . . . . . . . . . 38

Mode de configuration avancée . . . . . . . . . . 38

Accès au mode de configuration

avancée . . . . . . . . . . . . . . . . . . . . . . . 38

Programmation des fréquences RX

(réception) . . . . . . . . . . . . . . . . . . . . . . . . . 39

Programmation des codes RX (réception)

(CTCSS/DPL) . . . . . . . . . . . . . . . . . . . . . . 39

Programmation du brouillage . . . . . . . . . . . . 40

Programmation d’un nombre maximal de

canaux . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Programmation des tonalités d'appel. . . . . . 41

Programmation du niveau de gain du

microphone . . . . . . . . . . . . . . . . . . . . . . . . 42

Programmation du niveau de gain du

microphone auxiliaire. . . . . . . . . . . . . . . . . 43

Autres fonctions de programmation . . . . . . . 44

Balayage . . . . . . . . . . . . . . . . . . . . . . . . 44

Programmation de la liste de

balayage . . . . . . . . . . . . . . . . . . . . . . 44

Programmation du canal météo

TABLE DES MATIÈRES

Page 84

Français (Canada)

(non autorisé sur le modèle

RDX4163) . . . . . . . . . . . . . . . . . . . . . .45

Modification du nom de l'alias du

canal . . . . . . . . . . . . . . . . . . . . . . . . . .46

Suppression des nuisances sur le

canal . . . . . . . . . . . . . . . . . . . . . . . . . .46

Logiciel de programmation client (CPS) . . . .47

Minuterie de délai d’attente. . . . . . . . . . .48

Sélection de l'alimentation . . . . . . . . . . .48

Tonalités d'appel. . . . . . . . . . . . . . . . . . .49

Brouillage . . . . . . . . . . . . . . . . . . . . . . . .49

Rafale en arrière . . . . . . . . . . . . . . . . . . .49

Texte-parole (modification des alias

vocaux prédéfinis). . . . . . . . . . . . . . . . . . . .49

TABLE DES MATIÈRES

Case à cocher Activation des messages

vocaux prédéfinis par l'utilisateur . . . .49

Messages vocaux prédéfinis par

l'utilisateur . . . . . . . . . . . . . . . . . . . . . .49

Importer un fichier vocal . . . . . . . . . . . . .49

Écoute des messages vocaux définis par

l'utilisateur . . . . . . . . . . . . . . . . . . . . . .50

Fonction météo (non offerte sur le modèle

RDU4163). . . . . . . . . . . . . . . . . . . . . . . . . .50

Mode d'alerte météo . . . . . . . . . . . . . . . 51

Tableau des fréquences de canal

météo. . . . . . . . . . . . . . . . . . . . . . . . . 51

Il existe deux modes d'opération des alertes

météo :. . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

EOM activé . . . . . . . . . . . . . . . . . . . . . . 52

Minuterie de nouvelle tonalité d'alerte . . 52

Filtre de type d'événement. . . . . . . . . . . . . . 53

Tous les événements. . . . . . . . . . . . . . . 53

Événement de test d'alarme . . . . . . . . . 53

Avertissement . . . . . . . . . . . . . . . . . . . . . . . 54

Veille . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Urgence . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Communiqué . . . . . . . . . . . . . . . . . . . . . . . . 54

Filtre de code d'événement . . . . . . . . . . . . . 55

Blocage d'événement. . . . . . . . . . . . . . . . . . 55

Code d'événement . . . . . . . . . . . . . . . . . . . . 55

Tableau des événements critiques . . . . . . . 55

Filtre géographique . . . . . . . . . . . . . . . . . . . 57

État. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Comté. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

FIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Clonage de radios . . . . . . . . . . . . . . . . . . . . 58

Page 85

Français (Canada)

Clonage avec un chargeur

multi-unités (MUC) . . . . . . . . . . . . . . .58

Clonage de la radio au moyen du câble

de clonage de radio à radio (R2R)

(accessoire en option). . . . . . . . . . . . .60

Clonage à partir du logiciel de

programmation client (CPS) . . . . . . . .62

Dépannage. . . . . . . . . . . . . . . . . . . . . . . . . .63

Utilisation et entretien. . . . . . . . . . . . . . . . .67

Graphiques des fréquences et des

codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

RDU4163 – TABLEAU DES FRÉQUENCES

UHF PAR DÉFAUT. . . . . . . . . . . . . . . . . . .68

RDX – Tableau des fréquences UHF . . . . . .70

RDU4160 – Tableau des fréquences UHF par

défaut . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

PROGRAMMATION DES FRÉQUENCES

PERSONNALISÉES SUR LE MODÈLE

EDR4160 . . . . . . . . . . . . . . . . . . . . . . . . . .74

Codes CTCSS et PL/DPL . . . . . . . . . . . . . . .75

Accessoires . . . . . . . . . . . . . . . . . . . . . . . . .80

Antenne . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Accessoires audio . . . . . . . . . . . . . . . . . . . . 80

Batterie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Câbles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Chargeurs . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Accessoires de transport . . . . . . . . . . . . . . . 81

Applications logicielles . . . . . . . . . . . . . . . . . 81

Adaptateurs c.a. à broches pour blocs

d’alimentation . . . . . . . . . . . . . . . . . . . . . . 81

Blocs d'alimentation . . . . . . . . . . . . . . . . . . . 82

Garantie limitée de Motorola Solutions pour

les États-Unis et le Canada . . . . . . . . . . . . 83

TABLE DES MATIÈRES

Page 86

Français (Canada)

SÉCURITÉ DU PRODUIT

Mise en garde

SÉCURITÉ DU PRODUIT ET RESPECT DES NORMES RELATIVES À L'EXPOSITION AUX FRÉQUENCES RADIO

SÉCURITÉ DU PRODUIT

Pour être conforme aux règlements de la FCC relatifs aux normes d'exposition aux radiofréquences, cette radio ne doit être utilisée qu'à des fins professionnelles.

Pour obtenir une liste des antennes, des batteries et des autres accessoires autorisés par Motorola Solutions, visitez le site Web suivant :

www.motorolasolutions.com/RDX

Avant d'utiliser ce produit, veuillez lire les instructions d'utilisation et les informations sur l'exposition aux fréquences radio contenues dans la brochure « Sécurité du produit et exposition aux fréquences radio » fournie avec votre radio.

ATTENTION!

Page 87

Français (Canada)

INTRODUCTION

Nous vous remercions d'avoir acheté la radio RDX Series™ de Motorola Solutions produit de plus de 80 années d'expérience de Motorola Solutions en tant que leader mondial dans la conception et la fabrication d'équipement de communication. Les radios RDX Series offrent des communications à bon prix pour les entreprises telles que les magasins de détail, les restaurants, les écoles, les sites de construction, les manufactures, l'hôtellerie et bien plus encore. Les radios professionnelles bidirectionnelles de Motorola Solutions constituent la solution parfaite pour tous les secteurs au rythme rapide d'aujourd'hui. Remarque : Lisez attentivement ce guide d'utilisation

pour vous assurer que vous savez comment vous servir de votre radio de la façon adéquate avant de l'utiliser

CONTENU DE L'EMBALLAGE

• Radio

• Antenne

• Batterie au lithium-ion

• Pince de ceinture

. Cette radio est le

• Bloc d'alimentation

• Guide de référence rapide

• Chargeur instantané

• Brochure sur la sécurité du produit et l'exposition aux RF

Si vous souhaitez obtenir un exemplaire en gros caractères de ce guide de l'utilisateur ou avez une question relative au produit, veuillez communiquer avec

1 800 448-6686 aux États-Unis 1 800 927-4575 au Canada 1 888 390-6456 sur TTY (téléscripteur)

Pour des renseignements relatifs au produit, visitez-nous au :

www.motorolasolutions.com/RDX

Radios professionnelles Boîte postale 1C15, Motorola

8000, boul. Sunrise Ouest Plantation, Floride 33322

INTRODUCTION

Page 88

Français (Canada)

RENSEIGNEMENTS DE LICENCE FCC

INFORMATIONS RELATIVES AUX INTERFÉRENCES

Cet appareil est conforme aux stipulations de la Partie 15 des règlements de la FCC. Son utilisation est assujettie à la condition qu'il ne cause pas d'interférence nuisible.

Les radios professionnelles bidirectionnelles de la série RDX fonctionnent sur des

LICENCE FCC

fréquences radio régies par la Federal Communications Commission (FCC). Afin de

RENSEIGNEMENTS DE

transmettre sur ces fréquences, vous devez vous procurer une licence émise par la FCC. La demande doit être faite en remplissant le formulaire 601 et les annexez D et H, ainsi que le formulaire 159 (Remittance Form) de la FCC.

Pour obtenir ces formulaires de la FCC, demandez le document 000601 qui comprend tous les formulaires et les instructions. Si vous souhaitez que le document vous soit envoyé par télécopieur, par la poste ou si vous avez des questions, utilisez les coordonnées suivantes.

Pour obtenir une

télécopie, appelez le

système Fax-On-

Demand au :

1 202 418-0177 1 800 418-FORM

Pour obtenir une copie par la poste

des formulaires de la FCC,

1 800 418-3676

appelez au :

Pour des questions

concernant la licence FCC,

appelez la FCC au :

1 888 CALL-FCC 1 888 225-5322 Ou visitez la page : http://www.fcc.gov

Page 89

Français (Canada)

Avant de remplir votre demande, vous devez décider sur quelles fréquences vous souhaitez exploiter les radios. Reportez-vous à la section « Graphiques des fréquences et des codes ». Pour toute question sur le choix de la fréquence radio, appelez les services sur les produits de Motorola Solutions au :

1 800 448-6686

Toute modification effectuée à cet appareil sans l'autorisation explicite de Motorola Solutions peut annuler l'autorisation d'utiliser cet appareil, telle qu'autorisée par la FCC, et ne devrait pas être faite. Pour se conformer aux exigences de la FCC, les réglages de l'émetteur doivent être effectués par ou sous la surveillance d'un technicien certifiée pour faire l'entretien et les réparations d'émetteurrécepteur pour les services fixes ou mobiles terrestres privés, dont la certification provient

d'un représentant de l'organisation de l'utilisateur de ces services.

Le remplacement de n'importe quel composant de l'émetteur-récepteur (quartz, semi-conducteurs, etc.) non autorisé par l'autorisation d'équipement de la FCC pour cette radio risque d'enfreindre la réglementation de la FCC.

L'utilisation de cette radio en dehors du pays pour lequel elle est distribuée est soumise aux réglementations gouvernementales et peut être interdite.

RENSEIGNEMENTS DE

LICENCE FCC

Page 90

Français (Canada)

RENSEIGNEMENTS RELATIFS AUX LICENCES CANADIENNES

INFORMATION GÉNÉRALE

Le fonctionnement de votre radio Motorola Solutions est assujetti à la Loi sur la radiocommunication et doit se conformer aux règles et règlements du ministère de l’Industrie Innovation, Sciences et Développement économique Canada) (du gouvernement fédéral. Innovation, Sciences et Développement économique Canada exige que les utilisateurs de fréquences mobiles terrestres privées obtiennent une licence avant d'utiliser leur équipement.

Le formulaire de demande de licence d'Industrie Canada est inclus avec votre radio. Vous pouvez obtenir des formulaires supplémentaires et

RENSEIGNEMENTS RELATIFS

AUX LICENCES CANADIENNES

les plus récentes versions de demandes de licence auprès d'un bureau de district d'Innovation, Sciences et Développement économique Canada. Une liste de ces bureaux est incluse pour votre information.

Cet appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. Son utilisation est assujettie aux deux conditions suivantes:

1. Cet appareil ne doit pas causer d'interférence.

2. Cet appareil doit accepter toute interférence

reçue, y compris les interférences pouvant entraîner un fonctionnement indésirable de l'appareil.

DEMANDE DE LICENCE

Instructions générales

1. Remplissez les éléments en suivant les

instructions. Si vous avez besoin d'espace supplémentaire pour tout élément, utilisez le verso de la demande.

2. Assurez-vous d'utiliser une machine à écrire ou

d'écrire lisiblement.

3. Faites une copie pour vos fichiers.

4. Préparez un chèque ou un mandat-poste au

nom du « receveur général du Canada » au montant qui figure dans l'annexe suivante pour chaque radio achetée. (Les licences sont valides jusqu'au 1 puis sont renouvelées.)

5. Postez votre demande remplie ainsi que votre

chèque ou votre mandat-poste au bureau de district d'Innovation, Sciences et Développement économique Canada le plus près, conformément

avril de chaque année,

Page 91

Français (Canada)

à la liste des pages à.

Pour obtenir le plus récent formulaire de demande de licence canadienne, veuillez visiter :

www.ic.gc.ca

AUX LICENCES CANADIENNES

RENSEIGNEMENTS RELATIFS

Page 92

Français (Canada)

RENSEIGNEMENTS SUR L'UTILISATION SÉCURITAIRE DES BATTERIES ET DES CHARGEURS

Ce document contient d'importantes directives relatives à la sécurité et au fonctionnement de l'appareil. Veuillez lire attentivement cette notice et la conserver pour vous y référer ultérieurement. Avant d'utiliser le chargeur de batterie, lisez toutes les directives et marquages d'avertissement propres

• au chargeur,

RENSEIGNEMENTS SUR

• à la batterie et

BATTERIES ET DES CHARGEURS

L'UTILISATION SÉCURITAIRE DES

• à la radio qui utilise cette batterie

1. Afin de réduire les risques de blessure,

ne chargez que les batteries rechargeables agréées Motorola Solutions. Les batteries non agréées pourraient exploser et causer des blessures corporelles et autres dommages.

2. L'utilisation d'accessoires non recommandés

par Motorola Solutions pourrait occasionner des risques d'incendie, de choc électrique ou de blessure.

3. Afin de réduire la possibilité d'endommager la

fiche et le cordon d'alimentation, débranchez le chargeur en tirant sur la fiche au lieu du cordon.

4. Il n'est pas recommandé d'utiliser une rallonge,

sauf en cas de nécessité absolue. L'utilisation d'une rallonge inappropriée pourrait causer un risque d'incendie et de choc électrique. Si une rallonge doit être utilisée, assurez-vous que le format du cordon est de calibre 18 lorsque sa longueur est de 100 pieds (30,48 m) ou moins et de calibre 16 lorsque sa longueur est de 150 pieds (45,72 m) ou moins.

5. Pour réduire le risque d'incendie, de choc

électrique ou de blessure, n'utilisez pas le chargeur s'il est brisé ou endommagé de quelque manière que ce soit. Apportez-le à un technicien Motorola qualifié.

Page 93

Français (Canada)

6. Ne désassemblez pas le chargeur. Il ne peut

être réparé et aucune pièce de rechange n'est disponible. Le désassemblage du chargeur pourrait occasionner des risques de choc électrique ou d'incendie.

7. Pour réduire les risques de choc électrique,

débranchez le chargeur de la prise c.a. avant de procéder à une maintenance ou à un nettoyage.

DIRECTIVES D'UTILISATION SÉCURITAIRE

• Éteignez la radio lorsque vous chargez la batterie.

• Le chargeur n'est pas conçu pour une utilisation à l'extérieur. Ne l'utilisez que dans des emplacements secs et sous des conditions de nature semblable.

• Ne branchez le chargeur qu'à un bloc d'alimentation à fusible câblé approprié de tension prescrite (telle que spécifiée sur le produit).

• Débranchez le chargeur de la tension de secteur en retirant la fiche principale.

• La prise de courant à laquelle cet équipement est branché doit se trouver à proximité et être facilement accessible.

• Pour les appareils utilisant des fusibles, les pièces de rechange devront être conformes aux instructions fournies dans la documentation.

• La température ambiante maximale autour du bloc d'alimentation ne doit pas dépasser 40 °C (104 °F).

• La puissance de sortie du bloc d'alimentation ne devra pas dépasser la puissance indiquée sur l'étiquette du produit apposée sous le chargeur.

• Assurez-vous que le cordon est placé à un endroit où il ne sera pas écrasé ou endommagé, ne gênera pas le passage, ne sera pas tendu de façon anormale et ne sera pas exposé à une source d'humidité.

L'UTILISATION SÉCURITAIRE DES

BATTERIES ET DES CHARGEURS

RENSEIGNEMENTS SUR

Page 94

Français (Canada)

Antenne

Bouton Marche/ Arrêt/Volume

Voyant lumineux

Bouton sélecteur de canal

Connecteur à deux broches pour accessoire audio

Bouton PTT (Push-To-Talk)

Batterie

Microphone

SB1

SB2

Bouton programmable a

Bouton de menu

Affichage

Étiquette du modèle

PRÉSENTATION DE LA RADIO

PARTIES DE LA RADIO

Page 95

Français (Canada)

Bouton programmable a

Bouton de menu

Bouton Marche/Arrêt/Volume

Utilisé pour allumer et éteindre la radio et régler le volume.

Bouton sélecteur de canal

Utilisé pour changer les canaux de la radio.

Connecteur accessoire

Utilisé pour connecter des accessoires audio compatibles.

Étiquette du modèle

Indique le modèle de la radio.

Microphone

Parlez clairement dans le microphone lors de l'envoi d'un message.

Antenne

Pour les modèles RDX4160 et RDX4163, les antennes sont amovibles.

Voyant lumineux

Utilisé pour indiquer l'état de la batterie, de mise sous tension et de balayage et donner de l’information relative aux appels radio.

Boutons avant

Bouton de menu

• Donne accès aux fonctions de configuration comme les niveaux VOX/iVOX, etc. Il vous permet également de parcourir toutes les fonctions lorsque vous êtes en mode de programmation. Paramètre par défaut pour prérégler le canal 1.

Bouton programmable a

• Vous permet de sélectionner les options de niveau ou de bascule pour des fonctions affichées à l’écran. Paramètre par défaut pour générer la tonalité d'appel actuellement programmée.

PRÉSENTATION DE LA RADIO

Page 96

Français (Canada)

Bouton programmable b

• Vous permet de sélectionner les options de niveau ou de bascule pour des fonctions affichées à l’écran. Paramètre par défaut réglé au mode de rétroéclairage.

Remarque : Le fait d’appuyer brièvement sur le

bouton programmable (A ou B) règle la radio au canal prédéfini et la radio émet une forte tonalité. Vous pouvez attribuer différentes fonctions à ces boutons depuis le CPS. Exemple : Expiration du rétroéclairage, rafale en arrière, balayage ou suppression d’un canal nuisible, contrôle et tonalités d'appel. Pour en savoir plus sur la façon de programmer ces boutons, reportez-vous aux sections « Mode de configuration avancée » à la

PRÉSENTATION DE LA RADIO

page 38 et « » à la page 47.

BOUTONS LATÉRAUX

Bouton d'émission (PTT)

• Maintenez ce bouton enfoncé pour parler et relâchez-le pour écouter.

Bouton latéral 1 (SB1)

• Le bouton latéral 1 est un bouton général qui peut être configuré à partir du logiciel de programmation client (CPS). Le paramètre par défaut du SB1 est réglé à « Contrôle ».

Bouton latéral 2 (SB2)

• Le bouton latéral 2 est un bouton général qui peut être configuré par le CPS. Le paramètre par défaut du bouton SB2 est Balayage/Suppression d'un canal nuisible.

Batterie au lithium-ion (Li-Ion)

La radio de série RDX est livrée avec une batterie au lithium-ion de capacité standard. D'autres batteries peuvent être disponibles. Pour plus d'informations, reportez-vous à la section « Caractéristiques de la batterie » à la page 16. Ce guide de l'utilisateur couvre plusieurs modèles de la série RDX et peut décrire certaines fonctionnalités dont ne dispose pas votre radio. Le modèle de la radio est indiqué au bas de la radio et fournit les informations suivantes :

Page 97

Français (Canada)

Tableau 1 : Spécifications de la radio Série RDX

PRÉSENTATION DE LA RADIO

Modèle

RDU4160 UHF 4 16 Amovible

RDU4163 UHF 4 16 Amovible

Bande de

fréquences

CARACTÉRISTIQUES DE LA BATTERIE

Les radios de série RDX sont offertes avec des batteries au lithium-ion de différentes capacités qui définissent la durée de vie de la batterie.

À propos de la batterie lithium-ion

La radio Série RDX est équipée d'une batterie lithiumion rechargeable. Cette batterie doit être entièrement chargée avant la première utilisation pour assurer une capacité et une performance optimales.

L'autonomie de la batterie dépend de plusieurs facteurs. Parmi les plus importants, on retrouve la surcharge régulière des batteries et le niveau de perte de charge associé à chaque cycle. Généralement, un état de surcharge fréquent et un niveau de perte de charge important entraînent une diminution du

Puissance de

transmission

(watts)

Nombre de

canaux

nombre de cycles de la batterie. Par exemple, une batterie surchargée et déchargée à 100 % plusieurs fois par jour offrira moins de cycles de vie qu'une batterie moins surchargée et dont le niveau de perte de charge est de 50 % par jour. En outre, une batterie dont l'état de surcharge est minimal et dont le niveau de perte de charge moyen est de 25 % durera plus longtemps.

Les batteries Motorola Solutions sont conçues spécifiquement pour être utilisées avec un chargeur Motorola Solutions et inversement. La charge de la batterie au moyen d'un chargeur non-Motorola Solutions peut endommager la batterie et annuler sa garantie. La température de la batterie doit être d'environ 25 °C (77 °F) chaque fois que c'est possible. La charge de la batterie froide (moins de 10 °C

Antenne

Page 98

Français (Canada)

[50 °F]) peut entraîner une fuite d'électrolytes et, éventuellement, la défaillance de la batterie. La charge d'une batterie chaude (plus de 35 °C [95 °F]) réduit la capacité de permet de charge, ce qui affecte la performance de la radio. Les chargeurs rapides de Motorola Solutions contiennent un circuit de détection de la chaleur pour s'assurer que la température des batteries en cours de charge respecte les seuils de température indiqués cidessus.

Recyclage et mise au rebut des batteries

Les batteries au lithium-ion peuvent être recyclées. Cependant, on ne retrouve pas des installations de recyclage appropriées dans toutes les régions. En vertu de différentes lois d’États américains et des lois de plusieurs autres pays, les batteries doivent être recyclées et ne peuvent pas être mises au rebut dans les sites d'enfouissement ou les incinérateurs. Communiquez avec votre agence de gestion de

PRÉSENTATION DE LA RADIO

l'élimination des déchets obtenir des renseignements et connaître les exigences applicables dans votre région. Motorola Solutions soutient pleinement et encourage le recyclage des batteries au lithium-ion. Aux États-Unis et au Canada, Motorola Solutions participe au programme national Rechargeable Battery Recycling Corporation (Société de recyclage

des piles rechargeables) qui a comme objectif la collecte et le recyclage des batteries au lithium-ion.

De nombreux détaillants participent à ce programme. Pour connaître l'emplacement du dépôt le plus proche, consultez le site Web de la RBRC à l'adresse suivante :

http://www.call2recycle.org

Ou encore, composez le :

877 723-1297

Ce site Internet et ce numéro de téléphone donnent accès à des informations utiles sur les possibilités de recyclage qui s'offrent aux consommateurs, aux entreprises et aux agences gouvernementales.

Page 99

Français (Canada)

Installation de la batterie au lithium-ion

Loquet de la batterie

Fentes

Loquet de la batterie

(Li-Ion)

Remarque : Pour en savoir plus sur les

caractéristiques liées à la durée de vie de la batterie au lithium-ion, reportezvous à la section « À propos de la batterie lithium-ion » à la page 16.

Retrait de la batterie au lithium-ion (Li-Ion)

PRÉSENTATION DE LA RADIO

1. Éteignez la radio.

2. Le logo Motorola Solutions sur la batterie étant

3. Appuyez sur la partie supérieure de la batterie

tourné vers le haut, insérez les languettes au bas de la batterie dans les fentes au bas du corps de la radio.

en direction de la radio jusqu'à ce que vous entendiez un clic.

1. Éteignez la radio.

2. Poussez le loquet de la batterie vers le bas et

maintenez-le pendant que vous enlevez la batterie.

3. Retirez la batterie de la radio.

Page 100

Français (Canada)

Installation de l'antenne

Retrait de l'antenne

1. Alignez l'extrémité filetée de l'antenne de la

PRÉSENTATION DE LA RADIO

radio au connecteur d'antenne.

2. Tournez l'antenne dans le sens horaire pour

la fixer.

1. Tournez l'antenne dans le sens antihoraire

jusqu’à ce que vous puissiez la retirer.

Remarque : Ces directives s'appliquent

UNIQUEMENT aux modèles RDU4100 et RDV5100. Ne tentez pas de retirer l'antenne si votre radio n'est pas un de ces modèles.

Motorola RDU4160d, RDU4163d User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

CONTENTS

PRODUCT SAFETY

INTRODUCTION

PACKAGE CONTENTS

FCC LICENSING INFORMATION

INTERFERENCE INFORMATION

CANADA LICENSING INFORMATION

GENERAL INFORMATION

THE LICENSE APPLICATION

BATTERIES AND CHARGERS SAFETY INFORMATION

OPERATIONAL SAFETY GUIDELINES

RADIO OVERVIEW

PARTS OF THE RADIO

On/Off/Volume Knob

Channel Selector Knob

Accessory Connector

Model Label

Microphone

Antenna

LED Indicator

Front Buttons

SIDE BUTTONS

The Lithium-Ion (Li-Ion) Battery

BATTERY FEATURES

About the Li-Ion Battery

Battery Recycling and Disposal

Installing the Lithium-Ion (Li-Ion) Battery

Removing the Lithium-Ion (Li-Ion) Battery

Attaching the Antenna

Removing the Antenna

Installing Spring Action Belt clip.

Power Supply, Adaptor and Drop-in Tray Charger

Battery Life Information

Charging the Battery

Charging with the Drop-in Tray Single Unit Charger (SUC)

Drop-in Tray Charger LED Indicators

Estimated Charging Time

Charging a Radio and Battery using a Multi Unit-Charger - MUC (Optional Accessory)

Multi-Unit Charger LED Indicators

GETTING STARTED

TURNING RADIO ON/OFF

ADJUSTING VOLUME

READING THE DISPLAY

SELECTING A CHANNEL

TALKING AND MONITORING

RECEIVING A CALL

SIGNAL STRENGTH INDICATOR AND CHANNEL BUSY INDICATORS

TALK RANGE

RADIO LED INDICATORS

HANDS-FREE USE/VOX

With Compatible VOX Accessories

Hands Free without Accessories (iVOX)

TOGGLE VOICE PROMPT IN USER MODE

POWER UP - TONE MODE

RESET TO FACTORY DEFAULTS

KEYPAD BEEPS

KEYPAD LOCK/UNLOCK

MENU OPTIONS

SETTING VOX/IVOX SENSITIVITY

MICROPHONE GAIN

PROGRAMMING FEATURES

Advanced Configuration Mode

Entering Advanced Configuration Mode

PROGRAMMING RX (RECEPTION) FREQUENCIES

PROGRAMMING RX (RECEPTION) CODES (CTCSS/DPL)

PROGRAMMING SCRAMBLE

PROGRAMMING MAXIMUM NUMBER OF CHANNELS

PROGRAMMING CALL TONES

PROGRAMMING MICROPHONE GAIN LEVEL

PROGRAMMING MICROPHONE ACCESSORY GAIN LEVEL

OTHER PROGRAMMING FEATURES

Scan

Programming Scan List

Programming Weather Channel (Not allowed on RDX4163)

Editing Channel Alias Name

Nuisance Channel Delete