MOTOROLA MC14053BFR1, MC14053BFR2, MC14052BFR1, MC14052BFR2, MC14053BFL1 Datasheet

...

 Semiconductor Components Industries, LLC, 2000

March, 2000 – Rev. 3

1 Publication Order Number:

MC14051B/D

MC14051B, MC14052B, MC14053B

Analog Multiplexers/Demultiplexers

The MC14051B, MC14052B, and MC14053B analog multiplexers are digitally–controlled analog switches. The MC14051B effectively implements an SP8T solid state switch, the MC14052B a DP4T, and the MC14053B a Triple SPDT. All three devices feature low ON impedance and very low OFF leakage current. Control of analog signals up to the complete supply voltage range can be achieved.

• Triple Diode Protection on Control Inputs

• Switch Function is Break Before Make

• Supply Voltage Range = 3.0 Vdc to 18 Vdc

• Analog Voltage Range (V

– VEE) = 3.0 to 18 V

Note: VEE must be v V

• Linearized Transfer Characteristics

• Low–noise – 12 nV/√Cycle, f ≥ 1.0 kHz Typical

• Pin–for–Pin Replacement for CD4051, CD4052, and CD4053

• For 4PDT Switch, See MC14551B

• For Lower R

, Use the HC4051, HC4052, or HC4053 High–Speed

CMOS Devices

MAXIMUM RATINGS (Note 1.)

Symbol

Parameter Value Unit

DC Supply Voltage (Referenced

to V

, VSS ≥ VEE)

–0.5 to +18.0 V

Vin, V

out

Input or Output Voltage Range

(DC or Transient) (Referen– ced to V

for Control Inputs

and V

for Switch I/O)

–0.5 to VDD + 0.5 V

Input Current (DC or Transient)

per Control Pin

±10 mA

Switch Through Current ±25 mA

Power Dissipation,

per Package (Note 2.)

500 mW

Ambient Temperature Range –55 to +125 °C

stg

Storage Temperature Range –65 to +150 °C

Lead Temperature

(8–Second Soldering)

260 °C

1. Maximum Ratings are those values beyond which damage to the device

may occur.

2. Temperature Derating:

Plastic “P and D/DW” Packages: – 7.0 mW/_C From 65_C T o 125_C

This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high–impedance circuit. For proper operation, V

and V

out

should be constrained

to the range V

v (Vin or V

out

) v VDD.

Unused inputs must always be tied to an appropriate logic voltage level (e.g., either V

, VEE or VDD). Unused outputs must be left open.

http://onsemi.com

XX = Specific Device Code A = Assembly Location WL or L = Wafer Lot YY or Y = Year WW or W = Work Week

MARKING

DIAGRAMS

PDIP–16

P SUFFIX

CASE 648

MC140XXBCP

AWLYYWW

SOIC–16

D SUFFIX

CASE 751B

140XXB

AWLYWW

SOEIAJ–16

F SUFFIX

CASE 966

MC140XXB

AWLYWW

TSSOP–16 DT SUFFIX

CASE 948F

0XXB

ALYW

See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet.

ORDERING INFORMATION

MC14051B, MC14052B, MC14053B

http://onsemi.com

MC14051B

8–Channel Analog

Multiplexer/Demultiplexer

MC14052B

Dual 4–Channel Analog

Multiplexer/Demultiplexer

MC14053B

Triple 2–Channel Analog

Multiplexer/Demultiplexer

VDD = PIN 16

= PIN 8

= PIN 7

Note: Control Inputs referenced to VSS, Analog Inputs and Outputs reference to VEE. VEE must be ≤ VSS.

INHIBIT A B C X0 X1 X2 X3 X4 X5 X6 X7

CONTROLS

SWITCHES

IN/OUT

COMMON

OUT/IN

CONTROLS

SWITCHES

IN/OUT

COMMONS

OUT/IN

= PIN 16

= PIN 8

= PIN 7

CONTROLS

SWITCHES

IN/OUT

COMMONS

OUT/IN

= PIN 16

= PIN 8

= PIN 7

INHIBIT A B

X0 X1 X2 X3 Y0 Y1 Y2 Y3

INHIBIT A B

C X0

Y0 Y1 Z0 Z1

PIN ASSIGMENT

MC14051B MC14052B MC14053B

125

INH

125

INH

125

INH

MC14051B, MC14052B, MC14053B

http://onsemi.com

ELECTRICAL CHARACTERISTICS

– 55_C

25_C

125_C

Characteristic

Symbol

Test Conditions

Min

Max

Min

Typ

(3.)

Max

Min

Max

Unit

SUPPLY REQUIREMENTS (Voltages Referenced to VEE)

Power Supply Voltage

Range

—

VDD – 3.0 ≥ V

≥ V

3.0

—

3.0

ОООООО

Quiescent Current Per

Package

ÎÎ

5.0 10 15

ООООО

Control Inputs:

= VSS or VDD,

Switch I/O: V

v V

I/O

VDD, and ∆V

switch

500 mV

(4.)

— — —

5.0 10 20

— — —

ÎÎ

0.005

0.010

0.015

5.0 10 20

— — —

150 300 600

µA

ОООООО

Total Supply Current

(Dynamic Plus Quiescent, Per Package

ÎÎ

D(AV)

5.0 10 15

ООООО

TA = 25_C only (The

channel component, (V

– V

out

)/Ron, is

not included.)

ООООООООООООО

(0.07 µA/kHz) f + I

Typical (0.20 µA/kHz) f + I

(0.36 µA/kHz) f + I

µA

CONTROL INPUTS — INHIBIT, A, B, C (Voltages Referenced to VSS)

ОООООО

Low–Level Input Voltage

ÎÎ

5.0 10 15

ООООО

Ron = per spec, I

off

= per spec

— — —

1.5

3.0

4.0

— — —

ÎÎ

2.25

4.50

6.75

1.5

3.0

4.0

— — —

1.5

3.0

4.0

ОООООО

High–Level Input Voltage

ÎÎ

5.0 10 15

ООООО

Ron = per spec, I

off

= per spec

3.5

7.0 11

— — —

3.5

7.0 11

ÎÎ

2.75

5.50

8.25

— — —

3.5

7.0 11

— — —

Input Leakage Current

Vin = 0 or V

—

± 0.1

—

±0.00001

± 0.1

—

1.0

µA

Input Capacitance

—

5.0

7.5

—

SWITCHES IN/OUT AND COMMONS OUT/IN — X, Y, Z (Voltages Referenced to VEE)

ОООООО

Recommended

Peak–to–Peak Voltage Into or Out of the Switch

ÎÎ

I/O

—

ООООО

Channel On or Off

ÎÎ

—

DDVPP

ОООООО

Recommended Static or

Dynamic Voltage Across the Switch

(4.)

(Figure 5)

ÎÎ

∆V

switch

—

ООООО

Channel On

600

ÎÎ

—

600

300

Output Offset Voltage

—

Vin = 0 V, No Load

—

µV

ОООООО

ON Resistance

ÎÎ

5.0 10 15

ООООО

∆V

switch

v 500 mV

(4.)

Vin = VIL or V

(Control), and Vin = 0 to V

(Switch)

— — —

800 400 220

— — —

ÎÎ

250 120

1050

500 280

— — —

1200

520 300

Ω

ОООООО

∆ON Resistance Between

Any Two Channels in the Same Package

ÎÎ

∆R

5.0 10 15

ОООООÎÎ

— — —

70 50 45

— — —

ÎÎ

25 10 10

70 50 45

— — —

135

95 65

Ω

ОООООО

Off–Channel Leakage

Current (Figure 10)

ÎÎ

off

ООООО

Vin = VIL or V

(Control) Channel to Channel or Any One Channel

—

± 100

—

ÎÎ

± 0.05

± 100

—

±1000

Capacitance, Switch I/O

I/O

—

Inhibit = V

—

ОООООО

Capacitance, Common O/I

ÎÎ

O/I

—

ООООО

Inhibit = V

(MC14051B) (MC14052B) (MC14053B)

— — —

ÎÎ

60 32 17

— — —

ОООООО

Capacitance, Feedthrough

(Channel Off)

ÎÎ

I/O

— —

ООООО

Pins Not Adjacent Pins Adjacent

— —

———

—

ÎÎ

0.15

0.47

— —

——pF

3. Data labeled “Typ” is not to be used for design purposes, but is intended as an indication of the IC’s potential performance.

4. For voltage drops across the switch (∆V

switch

) > 600 mV ( > 300 mV at high temperature), excessive VDD current may be drawn, i.e. the

current out of the switch may contain both V

and switch input components. The reliability of the device will be unaffected unless the

Maximum Ratings are exceeded. (See first page of this data sheet.)

MC14051B, MC14052B, MC14053B

http://onsemi.com

ELECTRICAL CHARACTERISTICS

(5.)

= 50 pF, TA = 25_C) (VEE v VSS unless otherwise indicated)

Characteristic

Symbol

VDD – V

Vdc

Typ

(6.)

All Types

Max

Unit

ООООООООООООО

Propagation Delay Times (Figure 6)

Switch Input to Switch Output (R

= 10 kΩ)

MC14051

PLH

, t

PHL

= (0.17 ns/pF) CL + 26.5 ns

PLH

, t

PHL

= (0.08 ns/pF) CL + 11 ns

PLH

, t

PHL

= (0.06 ns/pF) CL + 9.0 ns

ÎÎÎ

PLH

, t

PHL

ÎÎÎ

5.0 10 15

ÎÎÎ

35 15 12

ÎÎÎ

90 40 30

ООООООООООООО

MC14052

PLH

, t

PHL

= (0.17 ns/pF) CL + 21.5 ns

PLH

, t

PHL

= (0.08 ns/pF) CL + 8.0 ns

PLH

, t

PHL

= (0.06 ns/pF) CL + 7.0 ns

ÎÎÎ

5.0 10 15

ÎÎÎ

30 12 10

ÎÎÎ

75 30 25

ООООООООООООО

MC14053

PLH

, t

PHL

= (0.17 ns/pF) CL + 16.5 ns

PLH

, t

PHL

= (0.08 ns/pF) CL + 4.0 ns

PLH

, t

PHL

= (0.06 ns/pF) CL + 3.0 ns

ÎÎÎ

5.0 10 15

ÎÎÎ

8.0

6.0

ÎÎÎ

65 20 15

ООООООООООООО

Inhibit to Output (RL = 10 kΩ, VEE = VSS) Output “1” or “0” to High Impedance, or High Impedance to “1” or “0” Level

MC14051B

ÎÎÎ

PHZ

, t

PLZ

PZH

, t

PZL

ÎÎÎ

5.0 10 15

ÎÎÎ

350 170 140

ÎÎÎ

700 340 280

ООООООООООООО

MC14052B

ÎÎÎÎÎÎÎ

5.0 10 15

ÎÎÎ

300 155 125

ÎÎÎ

600 310 250

ООООООООООООО

MC14053B

ÎÎÎÎÎÎÎ

5.0 10 15

ÎÎÎ

275 140 110

ÎÎÎ

550 280 220

ООООООООООООО

Control Input to Output (RL = 10 kΩ, VEE = VSS)

MC14051B

ÎÎÎ

PLH

, t

PHL

ÎÎÎ

5.0 10 15

ÎÎÎ

360 160 120

ÎÎÎ

720 320 240

ООООООООООООО

MC14052B

ÎÎÎÎÎÎÎ

5.0 10 15

ÎÎÎ

325 130

ÎÎÎ

650 260 180

ООООООООООООО

MC14053B

ÎÎÎÎÎÎÎ

5.0 10 15

ÎÎÎ

300 120

ÎÎÎ

600 240 160

ООООООООООООО

Second Harmonic Distortion

= 10KΩ, f = 1 kHz) Vin = 5 V

ÎÎÎ

—

ÎÎÎ

0.07

ÎÎÎ

—

ООООООООООООО

Bandwidth (Figure 7)

= 1 kΩ, Vin = 1/2 (VDD–VEE) p–p, CL = 50pF

20 Log (V

out/Vin

) = – 3 dB)

ÎÎÎ

—

MHz

ООООООООООООО

Off Channel Feedthrough Attenuation (Figure 7)

= 1KΩ, Vin = 1/2 (VDD – VEE) p–p

= 4.5 MHz — MC14051B

= 30 MHz — MC14052B

= 55 MHz — MC14053B

ÎÎÎ

—

ÎÎÎ

– 50

ÎÎÎ

—

ООООООООООООО

Channel Separation (Figure 8)

= 1 kΩ, Vin = 1/2 (VDD–VEE) p–p,

= 3.0 MHz

ÎÎÎ

—

ÎÎÎ

– 50

ÎÎÎ

—

ООООООООООООО

Crosstalk, Control Input to Common O/I (Figure 9)

= 1 kΩ, RL = 10 kΩ

Control t

TLH

= t

THL

= 20 ns, Inhibit = VSS)

ÎÎÎ

—

ÎÎÎ

—

5. The formulas given are for the typical characteristics only at 25_C.

6. Data labelled “Typ” is not lo be used for design purposes but In intended as an indication of the IC’s potential performance.

+ 8 hidden pages

MOTOROLA MC14053BFR1, MC14053BFR2, MC14052BFR1, MC14052BFR2, MC14053BFL1 Datasheet

Specifications and Main Features

Frequently Asked Questions

User Manual