Motorola MC12023D, MC12023P Datasheet

Device

Operating

Temperature Range

Package



SEMICONDUCTOR

TECHNICAL DATA

MECL PLL COMPONENTS

÷64 PRESCALER

ORDERING INFORMATION

MC12023D MC12023P

TA = 0° to 70°C

SO–8

Plastic

Order this document by MC12023/D

P SUFFIX

PLASTIC PACKAGE

CASE 626

PIN CONNECTIONS

D SUFFIX

PLASTIC PACKAGE

CASE 751

(SO–8)

(Top View)

NC AP

Out

Gnd

7 6 5

1 2 3 4

  

The MC12023 is a prescaler which will divide by 64. This device may be

operated over a supply voltage range of 3.2 to 5.5 V.

• 225 MHz Toggle Frequency

• Low-Power 4.8 mA Maximum at 5.5 V

• Operating Supply Voltage of 3.2 to 5.5 V

• Connecting Pins 2 and 3 Allows Driving One TTL Load

MAXIMUM RATINGS

Characteristic Symbol Range Unit

Power Supply Voltage V

0 to 8.0 Vdc

Operating Temperature Range T

0 to 70 °C

Storage Temperature Range T

stg

–65 to 175 °C

NOTE: ESD data available upon request.

ELECTRICAL CHARACTERISTICS (V

= 3.2 to 5.5V; TA = 0 to +70°C)

Characteristic Symbol Min Typ Max Unit

Toggle Frequency

(Sine Wave Input)

max

min

225

–

– –

–

MHz

Supply Current at 5.5 V I

– 3.50

4.8 mA

Output Voltage HIGH

(VCC = 3.2 V)

1.2 1.4 – V

Output Voltage HIGH

(VCC = 5.0 V)

2.5 – – V

Output Voltage LOW

sink

= 2.0 mA)

– – 0.5 V

Input Voltage Sensitivity

35 MHz

50–225 MHz

400 200

– –

800 800

NOTES: 1.Pin 2 connected to Pin 3

2.I

source

= 50 µA

3.VCC = 4.5 V

Figure 1. Prescaler Block Diagram

0.1µF

0.001 µF

Signal

Gnd

0.001 µF

Signal

Input

Active

Pull-Up

Gnd

Output

To V

 Motorola, Inc. 1997 Rev 2

MC12023

MOTOROLA RF/IF DEVICE DATA

P SUFFIX

PLASTIC PACKAGE

CASE 626-05

ISSUE K

D SUFFIX

PLASTIC PACKAGE

CASE 751-06

(SO–8)

ISSUE T

NOTES:

1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL.

2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS).

3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

MIN MINMAX MAX

MILLIMETERS INCHES

DIM

9.40

6.10

3.94

0.38

1.02

0.76

0.20

2.92 —

0.76

10.16

6.60

4.45

0.51

1.78

1.27

0.30

3.43

0.370

0.240

0.155

0.015

0.040

0.030

0.008

0.115 —

0.030

0.400

0.260

0.175

0.020

0.070

0.050

0.012

0.135

1.01

2.54 BSC

7.62 BSC

0.100 BSC

0.300 BSC

A B C D F G H J K L

0.040

NOTE 2

0.13 (0.005)

M M M

-A-

-B-

-T-

SEATING

PLANE

OUTLINE DIMENSIONS

SEATING PLANE

A0.25MCB

0.25MB

X 45

DIM MIN MAX

MILLIMETERS

A 1.35 1.75

A1 0.10 0.25

B 0.35 0.49 C 0.19 0.25 D 4.80 5.00

1.27 BSCe

3.80 4.00

H 5.80 6.20

0 7

L 0.40 1.25

0.25 0.50

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.

2. DIMENSIONS ARE IN MILLIMETER.

3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.

5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION.

0.10

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.

Mfax is a trademark of Motorola, Inc.

How to reach us: USA/EUROPE /Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 141,

P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447 4–32–1 Nishi–Gotanda, Shagawa–ku, Tokyo, Japan. 03–5487–8488

Customer Focus Center: 1–800–521–6274 Mfax: RMFAX0@email.sps.mot.com – TOUCHTONE 1–602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

Moto rola Fax Back Sys tem – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

– http://sps.motorola.com/mfax/

HOME PAGE: http://motorola.com/sps/

MC12023/D

◊