Motorola LM339N, LM3302P, LM2901N, LM2901D, LM239N Datasheet

3

2

1

Device

Operating

Temperature Range

Package




 



ORDERING INFORMATION

LM239D,AD
LM239N,AN

LM339D, AD
LM339N, AN

LM2901D
LM2901N

LM2901VD
LM2901VN

MC3302P

TA = 25° to +85°C

SO–14

Plastic DIP

SO–14

Plastic DIP

SO–14

Plastic DIP

SO–14

Plastic DIP
Plastic DIP

Order this document by LM339/D

D SUFFIX

PLASTIC PACKAGE

CASE 751A

(SO–14)

N, P SUFFIX

PLASTIC PACKAGE

CASE 646

PIN CONNECTIONS

14

1

1

14

*
)

*
)

1

2

3

4

5

6

7

14

8

9

10

11

12

13

Output 2

– Input 1

Output 1

Output 3
Output 4

+ Input 1
– Input 2
+ Input 2

+ Input 4
– Input 4

+ Input 3
– Input 3

V

CC

Gnd

)
*

)
*

4

(Top View)

TA = 0° to +70°C

TA = –40° to +105°C

TA = –40° to +85°C

TA = –40° to +125°C

1

MOTOROLA ANALOG IC DEVICE DATA

  


These comparators are designed for use in level detection, low–level
sensing and memory applications in consumer automotive and industrial
electronic applications.

• Single or Split Supply Operation

• Low Input Bias Current: 25 nA (Typ)

• Low Input Offset Current: ±5.0 nA (Typ)

• Low Input Offset Voltage: ±1.0 mV (Typ) LM139A Series

• Input Common Mode Voltage Range to Gnd

• Low Output Saturation Voltage: 130 mV (Typ) @ 4.0 mA

• TTL and CMOS Compatible

• ESD Clamps on the Inputs Increase Reliability without Affecting Device

Operation

MAXIMUM RATINGS

Rating Symbol Value Unit

Power Supply Voltage V

CC

Vdc
LM239, A/LM339A/LM2901, V +36 or ±18
MC3302 +30 or ±15

Input Differential Voltage Range V

IDR

Vdc
LM239, A/LM339A/LM2901, V 36
MC3302 30

Input Common Mode Voltage Range V

ICMR

–0.3 to V

CC

Vdc

Output Short Circuit to Ground (Note 1) I

SC

Continuous

Power Dissipation @ TA = 25°C P

D

Plastic Package 1.0 W
Derate above 25°C 8.0 mW/°C

Junction Temperature T

J

150 °C

Operating Ambient Temperature Range T

A

°C
LM239, A –25 to +85
MC3302 –40 to +85
LM2901 –40 to +105
LM2901V –40 to +125
LM339, A 0 to +70

Storage Temperature Range T

stg

–65 to +150 °C

NOTE: 1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC.

Output short circuits to VCC can cause excessive heating and eventual destruction.

Figure 1. Circuit Schematic

V

CC

+ Input – Input Output

Gnd

NOTE: Diagram shown is for 1 comparator.

 Motorola, Inc. 1996 Rev 2

LM339, LM339A, LM239, LM239A, LM2901, M2901V, MC3302

2

MOTOROLA ANALOG IC DEVICE DATA

ELECTRICAL CHARACTERISTICS

(VCC = +5.0 Vdc, TA = +25°C, unless otherwise noted)

LM239A/339A LM239/339 LM2901/2901V MC3302

Characteristic Symbol

Min Typ Max Min Typ Max Min Typ Max Min Typ Max

Unit

Input Offset Voltage (Note 4) V

IO

– ±1.0 ±2.0 – ±2.0 ±5.0 – ±2.0 ±7.0 – ±3.0 ±20 mVdc

Input Bias Current (Notes 4, 5) I

IB

– 25 250 – 25 250 – 25 250 – 25 500 nA

(Output in Analog Range)

Input Offset Current (Note 4) I

IO

– ±5.0 ±50 – ±5.0 ±50 – ±5.0 ±50 – ±3.0 ±100 nA

Input Common Mode Voltage Range V

ICMR

0 – V

CC

–1.5

0 – V

CC

–1.5

0 – V

CC

–1.5

0 – V

CC

–1.5

V

Supply Current I

CC

mA
RL = ∞ (For All Comparators) – 0.8 2.0 – 0.8 2.0 – 0.8 2.0 – 0.8 2.0
RL = ∞, VCC = 30 Vdc – 1.0 2.5 – 1.0 2.5 – 1.0 2.5 – 1.0 2.5

Voltage Gain A

VOL

50 200 – 50 200 – 25 100 – 25 100 – V/mV

RL ≥ 15 kΩ, VCC = 15 Vdc

Large Signal Response Time – – 300 – – 300 – – 300 – – 300 – ns

VI = TTL Logic Swing,
V

ref

= 1.4 Vdc, VRL = 5.0 Vdc,

RL = 5.1 kΩ

Response Time (Note 6) – – 1.3 – – 1.3 – – 1.3 – – 1.3 – µs

VRL = 5.0 Vdc, RL = 5.1 kΩ

Output Sink Current I

Sink

6.0 16 – 6.0 16 – 6.0 16 – 6.0 16 – mA
VI (–) ≥ +1.0 Vdc, VI(+) = 0,
VO ≤ 1.5 Vdc

Saturation Voltage V

sat

– 130 400 – 130 400 – 130 400 – 130 500 mV
VI(–) ≥ +1.0 Vdc, VI(+) = 0,
I

sink

≤ 4.0 mA

Output Leakage Current I

OL

– 0.1 – – 0.1 – – 0.1 – – 0.1 – nA
VI(+) ≥ +1.0 Vdc, VI(–) = 0,
VO = +5.0 Vdc

PERFORMANCE CHARACTERISTICS (V

CC

= +5.0 Vdc, TA = T

low

to T

high

[Note 3])

LM239A/339A LM239/339 LM2901/2901V MC3302

Characteristic Symbol

Min Typ Max Min Typ Max Min Typ Max Min Typ Max

Unit

Input Offset Voltage (Note 4) V

IO

– – ±4.0 – – ±9.0 – – ±15 – – ±40 mVdc

Input Bias Current (Notes 4, 5) I

IB

– – 400 – – 400 – – 500 – – 1000 nA
(Output in Analog Range)

Input Offset Current (Note 4) I

IO

– – ±150 – – ±150 – – ±200 – – ±300 nA

Input Common Mode Voltage Range V

ICMR

0 – V

CC

–2.0

0 – V

CC

–2.0

0 – V

CC

–2.0

0 – V

CC

–2.0

V

Saturation Voltage V

sat

– – 700 – – 700 – – 700 – – 700 mV
VI(–) ≥ +1.0 Vdc, VI(+) = 0,
I

sink

≤ 4.0 mA

Output Leakage Current I

OL

– – 1.0 – – 1.0 – – 1.0 – – 1.0 µA
VI(+) ≥ +1.0 Vdc, VI(–) = 0,
VO = 30 Vdc

Differential Input Voltage V

ID

– – V

CC

– – V

CC

– – V

CC

– – V

CC

Vdc

All VI ≥ 0 Vdc

NOTES: 3. (LM239/239A) T

low

= –25°C, T

high

= +85°

(LM339/339A) T

low

= 0°C, T

high

= +70°C

(MC3302) T

low

= –40°C, T

high

= +85°C

(LM2901) T

low

= –40°C, T

high

= +105°

(LM2901V) T

low

= –40°C, T

high

= +125°C

4.At the output switch point, VO ] 1.4 Vdc, RS ≤ 100 Ω 5.0 Vdc ≤ VCC ≤ 30 Vdc, with the inputs over the full common mode range
(0 Vdc to VCC –1.5 Vdc).

5.The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state.

6.The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical.