MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
128K x 8 Bit Fast Static Random
Access Memory
Order this document
by MCM6726D/D
MCM6726D
The MCM6726D is a 1,048,576 bit static random access memory organized
as 131,072 words of 8 bits. Static design eliminates the need for external clocks
or timing strobes.
Output enable (G
) is a special control feature that provides increased system
flexibility and eliminates bus contention problems.
This device meets JEDEC standards for functionality and revolutionary pinout,
and is available in a 400 mil plastic small–outline J–leaded package.
• Single 5 V ± 10% Power Supply
• Fully Static — No Clock or Timing Strobes Necessary
• All Inputs and Outputs Are TTL Compatible
• Three State Outputs
• Fast Access Times: 8, 10, 12 ns
• Center Power and I/O Pins for Reduced Noise
BLOCK DIAGRAM
A
V
A
A
A
A
A
A
A
A
ROW
DECODER
MEMORY
MATRIX
512 ROWS x 256 x 8
COLUMNS
CC
V
SS
WJ PACKAGE
400 MIL SOJ
CASE 857A–02
PIN ASSIGNMENT
AA
1
A
2
A
3
A
4
E
5
DQ
6
DQ
7
V
8
CC
V
9
SS
DQ
10
DQ
11
W
12
A
13
A
14
A
15
A
16
32
A
31
A
30
A
29
G
28
DQ
27
DQ
26
V
SS
25
V
CC
24
DQ
23
DQ
22
A
21
A
20
A
19
A
18
A
17
DQ
INPUT
DATA
CONTROL
DQ
E
W
G
10/9/96
Motorola, Inc. 1996
MOTOROLA FAST SRAM
COLUMN I/O
COLUMN DECODER
AA A A
A A A A
PIN NAMES
A Address Input. . . . . . . . . . . . . . . . . . . .
E
W
G
DQ Data Input/Output. . . . . . . . . . . . . . .
V
CC
V
SS
+ 5 V Power Supply. . . . . . . . . . . .
Chip Enable. . . . . . . . . . . . . . . . . . . . . .
Write Enable. . . . . . . . . . . . . . . . . . . .
Output Enable. . . . . . . . . . . . . . . . . . .
Ground. . . . . . . . . . . . . . . . . . . . . . .
MCM6726D
1
TRUTH TABLE (X = Don’t Care)
G W Mode VCC Current Output Cycle
E
H X X Not Selected I
L H H Output Disabled I
L L H Read I
L X L Write I
SB1
, I
CCA
CCA
CCA
SB2
High–Z —
High–Z —
D
out
High–Z Write Cycle
Read Cycle
ABSOLUTE MAXIMUM RATINGS (See Note)
Rating
Power Supply Voltage V
Voltage Relative to VSS for Any Pin Except
V
CC
Output Current I
Power Dissipation P
Temperature Under Bias T
Operating Temperature T
Storage Temperature — Plastic T
NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are
exceeded. Functional operation should be restricted to RECOMMENDED OPERATING CONDITIONS. Exposure to higher than recommended voltages for
extended periods of time could affect device reliability.
Symbol Value Unit
CC
Vin, V
out
bias
stg
out
D
A
– 0.5 to + 7.0 V
– 0.5 to VCC + 0.5 V
± 30 mA
1.2 W
– 10 to + 85 °C
0 to + 70 °C
– 55 to + 125 °C
This device contains circuitry to protect the
inputs against damage due to high static voltages or electric fields; however, it is advised
that normal precautions be taken to avoid application of any voltage higher than maximum
rated voltages to these high–impedance circuits.
This BiCMOS memory circuit has been designed to meet the dc and ac specifications
shown in the tables, after thermal equilibrium
has been established. The circuit is in a test
socket or mounted on a printed circuit board
and transverse air flow of at least 500 linear feet
per minute is maintained.
DC OPERA TING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 10%, TA = 0 to 70°C, Unless Otherwise Noted)
RECOMMENDED OPERATING CONDITIONS
Parameter Symbol Min Typ Max Unit
Supply Voltage (Operating Voltage Range) V
Input High Voltage V
Input Low Voltage V
*VIL (min) = –0.5 V dc; VIL (min) = –2.0 V ac (pulse width ≤ 2.0 ns) for I ≤ 20.0 mA.
**VIH (max) = VCC + 0.3 V dc; VIH (max) = VCC + 2 V ac (pulse width ≤ 2.0 ns) for I ≤ 20.0 mA.
CC
IH
IL
DC CHARACTERISTICS
Parameter Symbol Min Max Unit
Input Leakage Current (All Inputs, Vin = 0 to VCC) I
Output Leakage Current (E = VIH, V
Output Low Voltage (IOL = + 8.0 mA) V
Output High Voltage (IOH = – 4.0 mA) V
= 0 to VCC) I
out
POWER SUPPLY CURRENTS
Parameter Symbol 6726D–8 6726D–10 6726D–12 Unit Notes
AC Active Supply Current (I
Active Quiescent Current (E = VIL, VCC = max, f = 0 MHz) I
AC Standby Current (E = VIH, VCC = max, f = f
CMOS Standby Current (VCC = max, f = 0 MHz, E ≥ VCC – 0.2 V,
Vin ≤ VSS + 0.2 V, or ≥ VCC – 0.2 V)
NOTES:
1. Reference AC Operating Conditions and Characteristics for input and timing (VIH/VIL, tr/tf, pulse level 0 to 3.0 V, VIH = 3.0 V).
2. All addresses transition simultaneously low (LSB) and then high (MSB).
3. Data states are all zero.
= 0 mA) (VCC = max, f = f
out
max
) I
max
) I
CCA
CC2
SB1
I
SB2
4.5 5.0 5.5 V
2.2 —
– 0.5*
lkg(I)
lkg(O)
OL
OH
195 175 165 mA 1, 2, 3
100 100 100 mA
60 60 60 mA 1, 2, 3
20 20 20 mA
— 0.8 V
— ±1.0 µA
— ±1.0 µA
— 0.4 V
2.4 — V
VCC + 0.3**
V
MCM6726D
2
MOTOROLA FAST SRAM
CAPACITANCE (f = 1.0 MHz, dV = 3.0 V, T
Address Input Capacitance C
Control Pin Input Capacitance C
Input/Output Capacitance C
= 25°C, Periodically Sampled Rather Than 100% Tested)
A
Parameter
Symbol Typ Max Unit
in
in
I/O
— 6 pF
— 6 pF
— 8 pF
AC OPERA TING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ±10%, TA = 0 to +70°C, Unless Otherwise Noted)
Input Timing Measurement Reference Level 1.5 V. . . . . . . . . . . . . . .
Input Pulse Levels 0 to 3.0 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Rise/Fall Time 2 ns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
READ CYCLE TIMING (See Notes 1 and 2)
Parameter Symbol Min Max Min Max Min Max Unit Notes
Read Cycle Time t
Address Access Time t
Enable Access Time t
Output Enable Access Time t
Output Hold from Address Change t
Enable Low to Output Active t
Output Enable Low to Output Active t
Enable High to Output High–Z t
Output Enable High to Output High–Z t
NOTES:
1. W
is high for read cycle.
2. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycles.
3. All read cycle timings are referenced from the last valid address to the first transitioning address.
4. At any given voltage and temperature, t
to device.
5. Transition is measured 200 mV from steady–state voltage with load of Figure 1b.
6. This parameter is sampled and not 100% tested.
7. Device is continuously selected (E
8. Addresses valid prior to or coincident with E
= VIL, G = VIL).
EHQZ
max < t
going low.
ELQX
min, and t
Output Timing Measurement Reference Level 1.5 V. . . . . . . . . . . . .
Output Load See Figure 1a. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6726D–8 6726D–10 6726D–12
AVAV
AVQV
ELQV
GLQV
AXQX
ELQX
GLQX
EHQZ
GHQZ
8 — 10 — 12 — ns 3
— 8 — 10 — 12 ns
— 8 — 10 — 12 ns
— 4 — 5 — 6 ns
3 — 3 — 3 — ns
3 — 3 — 3 — ns 4,5,6
0 — 0 — 0 — ns 4,5,6
— 4 — 5 — 6 ns 4,5,6
— 4 — 5 — 6 ns 4,5,6
GHQZ
max < t
min, both for a given device and from device
GLQX
OUTPUT
Z0 = 50
Ω
(a) (b)
MOTOROLA FAST SRAM
RL = 50
VL = 1.5 V
OUTPUT
Ω
255
Figure 1. AC TEST LOADS
TIMING LIMITS
+5 V
480
Ω
Ω
5 pF
The table of timing values shows either a
minimum or a maximum limit for each parameter. Input requirements are specified from
the external system point of view. Thus, address setup time is shown as a minimum
since the system must supply at least that
much time. On the other hand, responses
from the memory are specified from the device point of view. Thus, the access time is
shown as a maximum since the device never
provides data later than that time.
MCM6726D
3