Motorola H800 user Manual
H800
motorola
Slider
Bluetooth® Headset
Get connected in 4 quick steps.
BEFORE YOU BEGIN
Before using this product, read the Important Safety and Legal
Information pamphlet and follow its instructions.
Take a moment before you get started to
familiarize yourself with your new
H800 Headset.
Call
Button
Speaker
(other side)
Multi-Color
Indicator Light
Microphone
Slider
Charging Port
(other side)
Slider Lock
Switch
Volume
Buttons
1
Open charger port cover and plug the Motorola
1
charger into the charging port on the headset.
Note: Your headset has a micro USB charging port. If using
a mini USB charger, utilize the included micro USB adapter
when charging (shown on right).
With Micro USB Charger With Mini USB Charger and
The indicator light turns red when the battery is
charging. It may take up to 1 minute for the
indicator light to turn on. When the headset's
battery is 80% charged, the indicator light turns
yellow. When charging is complete (about 2
hours), the indicator light turns green.
Disconnect charger and close charger port
2
cover.
Note: Headset is not functional while charging.
CHARGE
Your Headset's Battery
Micro USB Adapter
2
START BLUETOOTH
FEATURE
Your Phone
Your phone's Bluetooth feature is off by default.
To use your headset, you must turn on the
Bluetooth feature in your phone.
For most Motorola phones (at the main menu):
M
Press (
1
Bluetooth Link > Setup.
2
Scroll to Power.
3
Select Change.
Scroll to On.
4
5
Press Select to turn on the Bluetooth
feature. The Bluetooth feature remains on
until you turn the feature off.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
Menu) > Settings > Connection >
3
Before you can use your headset, you must pair
(link) it with your phone.
Step A - ENSURE HEADSET IS IN PAIRING
MODE
Power on headset by pressing the Call button
to initiate easy pairing. After a few moments,
the indicator light will be steadily lit in blue to
indicate headset is in pairing mode.
Indicator Light
(steadily blue
for pairing mode)
If the headset does not enter pairing mode,
see TROUBLESHOOTING for help.
PAIR
Your Headset
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
www.hellomoto.com
1-877-MOTOBLU
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
Guide Number: 6809506A84-A
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The use of wireless devices and their
accessories may be prohibited or restricted in certain areas.
Always obey the laws and regulations on the use of these
products. The Bluetooth trademarks are owned by their
proprietor and used by Motorola, Inc. under license. All other
product or service names are the property of their respective
owners.
© Motorola, Inc. 2007.
3
Step B - SET YOUR PHONE TO LOOK FOR
YOUR HEADSET
For most Motorola phones:
On your Motorola phone, press (
1
PAIR
CONTINUED
Your Phone
M
Menu) >
Settings > Connection > Bluetooth L in k >
Handsfree > Look for D ev ic es .
The phone lists Bluetooth devices it finds.
Select Motorola H800.
2
Select OK or Yes to pair your headset with
3
your phone.
Enter the passkey: 0000
4
Select OK.
5
When your headset successfully pairs with
your phone, the indicator light flashes purple
and blue.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
4
Your phone and headset are now paired and
ready to make and receive calls.
To make a call:
1
Place the headset over your ear.
On the phone, dial the number you want to
2
call and press SEND key on your phone.
If your phone and headset are successfully
3
paired, you will hear ringing on the headset.
After you have successfully paired your
phone and headset, you don't need to
repeat these steps. For daily use, ensure
that your headset is turned ON and that
your phone's Bluetooth feature is ON.
To save battery power, turn OFF the
headset when you don't use it for an
extended time by closing the slider.
TEST AND USE
USING YOUR H800
See
Features and
Functions Guide
on the reverse side
for information on
using your H800
TROUBLESHOOTING
My headset will not enter pairing mode.
Make sure that any devices previously paired
with the headset are turned off. If the indicator
light is flashing in blue, first turn off the other
device, then turn your headset off and on. The
indicator light becomes steadily lit in blue
indicating the headset is now in pairing mode.
My phone doesn't find my headset.
Make sure the indicator light on your headset is
on (lit in blue) and steady when your phone is
searching for devices (see step 3).
My headset worked before but now it's not
working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone (see step 2).
If the Bluetooth feature was turned off or was
turned on only temporarily, you may need to
restart the Bluetooth feature (see step 2) and
pair your phone and headset again (see step 3).
Support.
If you need more help, contact us at
1-877-MOTOBLU or visit us at
www.hellomoto.com/Bluetoothsupport
Features and
Functions Guide
H800
Slider
Bluetooth® Headset
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H800.
TURNING HEADSET
ON AND OFF
To turn your headset on, press the Call
button to extend the slider. The indicator
light flashes blue (if paired with another
device), or is steadily blue (if ready to be
paired).
To turn your headset off, push the slider
closed. The indicator light flashes blue three
times.
Call
Multi-Color
Indicator Light
Slider
To prevent accidental headset operation, slide
the slider lock switch to the locked position.
Button
Slider Lock Switch
(in locked position)
EARHOOKS AND YOUR
HEADSET
Your H800 headset is supplied with multiple size
earhooks. The earhook is attached onto a hinge pin,
and is placed onto your ear when using your
headset. To install an earhook on your headset:
Open the attached
1
earhook 90 degrees from
the headset.
Gently lift and pull the
2
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
remove it.
Position the headset for
3
right or left ear use (right
ear use is displayed).
Hook the bottom of the
4
earhook onto the lower
hinge pin, then lift and pull
the top of the earhook
over the upper hinge pin.
1 Open Earhook
2 Pull Earhook Up
Hinge Pin
WEARING THE
HEADSET
Once you have attached your desired
earhook, follow these steps to wear your
headset on your ear:
Open the attached
1
earhook 45 degrees from
the headset.
2
Loop the earhook over
your ear.
Press earhook to your ear.
3
When worn, your headset
will look like this on your
head:
1
2
CHANGING VOLUME
BUTTON ORIENTATION
You can also change the orientation of the
volume buttons on your headset.
Turn the headset power off.
1
Press the Volume button you want to
2
assign as the "volume up" button and
press the Call button to extend the slider
(to power on the headset). The indicator
light flashes three times in blue.
Call
3
Button
Volume
Buttons
European Union Directives
Conformance Statement
Hereby, Motorola declares that this
product is in compliance with:
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
• All other relevant EU Directives.
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
You can view your product’s Declaration of Conformity
(DoC) to Directive 1999/5/EC (to R&TTE Directive) at
www.motorola.com/rtte. To find your DoC, enter the
product Approval Number from your product’s label in
the “Search” bar on the web site.
MAKING CALLS
Function Action
Make a voice dial call Tap the Call button
and speak the
name after the tone
End a call Tap the Call button
Answer a call Tap the Call button
Ignore a call Press and hold either
Volume button until
incoming call stops
ringing
Redial last call Press and hold the
Call button for at least
2 seconds until you
hear a beep
Mute or unmute a call Tap both Volume
buttons
Note: Some features are phone/network dependent.
Note: Your H800 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which profile
your phone supports. See your phone's user's guide for more
information.
MAKING CALLS
Function Action
Disable/Enable the Press and hold both
indicator light Volume buttons at the
same time while
powering on headset
Answer a second Tap the Call button
incoming call
End active call and Tap the Call button
resume call on hold
Note: Resuming a call on hold is a phone-dependent feature.
If tapping the Call button does not execute action, revert to
the phone controls to resume call on hold.
Note: When indicator light is disabled, light does not display
for any headset function. Re-enable indicator light by pressing
and holding both Volume buttons at the same time while
powering on headset.
CONTINUED
INDICATOR LIGHTS
With the Charger Plugged In
Headset Indicator Headset Status
Red Charging
Yellow Charging 80% done
Green Charging complete
With No Charger Plugged In
Headset Indicator Headset Status
Off Power off
Three blue flashes Powering on/off
Steady blue Pairing mode
Rapid blue/purple flashes Pairing successful
Quick blue flash Incoming/outgoing call
Slow blue pulse Connected (on a call)
Slow blue flash Standby (not on a call)
Slow red flash Idle (not connected
to phone)
Slow purple pulse Connected call muted
Quick red flash Low battery
Note: After 20 minutes on a call or of inactivity, the light stops
flashing to conserve power, but the headset remains on.
AUDIO TONES
Audio Tone Headset Status
Ascending tone Powering on
Descending tone Powering off
Two ascending Pairing successful/
tones Initiate voice dial
Ring tone Incoming call
Two short tones when Volume at minimum
pressing Volume button or maximum
High/low tones Low battery
repeated every 60 sec.
No audio indications; Out of range
deteriorating quality
Three ascending tones Connected call/
Redial last number
Three descending tones Ended call
Two rapid ascending Mute enabled
tones
Two rapid descending Mute disabled
tones
Loading...