Page 1
BEFORE YOU
BEGIN
Before using this product, read the Important Safety and
Legal Information pamphlet and follow its instructions.
motorola
H710
Quick Start Guide
Take a moment before you get started to
familiarize yourself with your new
H710 Headset.
Call
Volume
Buttons
Speaker
(on reverse
side)
Button
Multi-Color
Indicator Light
Boom
Microphone
(on reverse side)
1
Your Headset's Battery
Charge your headset's battery for 2 hours:
Plug the Motorola charger into the end of
1
the headset.
The indicator light turns red when the battery
is charging. It may take up to 1 minute for
the indicator light to turn on. When the
headset's battery is fully charged (about 2
hours), the indicator light turns green.
Disconnect the charger.
2
Note: Headset is not functional while charging.
Note: This product uses a lithium ion, rechargeable,
non-replaceable battery. Under normal use, the expected life
of the rechargeable battery is approximately 400 charges.
CHARGE
2
START BLUETOOTH
FEATURE
Your Phone
Your phone's Bluetooth feature is off by default.
To use your headset, you must turn on the
Bluetooth feature in your phone.
For most Motorola phones (at the main menu):
M
Press (
1
Bluetooth Link > Setup.
2
Scroll to Power.
3
Select Change.
Scroll to On.
4
5
Press Select to turn on the Bluetooth
feature. The Bluetooth feature remains on
until you turn it off.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
Menu) > Settings > Connection >
Page 2
3
A
s
P
Your Head
IR
et and Phone
Before you can use your headset, you must pair
(link) it with your phone.
Step A - ENSURE HEADSET IS IN PAIRING
MODE
Open the headset boom to power on the
headset and initiate pairing. After a few
moments, the indicator light will be steadily lit
in blue to indicate headset is in pairing mode.
Indicator Light
(steadily blue
for pairing mode)
If the headset does not enter pairing mode,
see TROUBLESHOOTING for help.
Step B - SET YOUR PHONE TO LOOK FOR
YOUR HEADSET
For most Motorola phones:
On your Motorola phone, press (
1
M
Menu) >
Settings > Connection > Bluetooth Link > Handsfree
> Look for Devices.
The phone lists Bluetooth devices it finds.
Select Motorola H710.
2
Select OK or Ye s to pair your headset with
3
your phone.
Enter the passkey: 0000
4
Select OK.
5
When your headset successfully pairs with
your phone, the indicator light flashes
purple and blue.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
www.hellomoto.com
1-877-MOTOBLU
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
Guide Number: 6809520A03-O
Bluetooth QD ID: B013079
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The use of wireless devices and their
accessories may be prohibited or restricted in certain areas.
Always obey the laws and regulations on the use of these
products. The Bluetooth trademarks are owned by their
proprietor and used by Motorola, Inc. under license. All other
product or service names are the property of their respective
owners.
4
Your phone and headset are now paired and
ready to make and receive calls. To confirm they
are operating properly, make a call:
Place the headset over your ear.
1
On the phone, dial the number you want to
2
call and press SEND key on your phone.
If your phone and headset are successfully
3
paired, you will hear ringing on the headset.
After you have successfully paired your phone
and headset, you don't need to repeat these
steps. For daily use, ensure that your headset is
turned ON and that your phone's Bluetooth
feature is ON.
To conserve power, close the boom to turn your
headset off. Re-open the boom to make a call.
TEST AND USE
© Motorola, Inc. 2007.
Page 3
USING A S
E
COND PHONE?
Multipoint technology allows you to make and
receive calls from two Bluetooth enabled
devices like your personal and business phones.
To pair a second phone to your headset, follow
these steps:
Turn off any phones or devices that are
1
already paired with your headset.
Turn off your headset by closing the headset
2
boom.
Perform Step 2 (“Start Bluetooth Feature”),
3
and Step 3 (”Pair”), and Step 4 (”Test and
Use”) to pair your headset with your second
phone.
To reconnect your headset with your first phone
(and thus be connected to both phones), follow
these steps:
Turn on first phone.
1
Use your first phone to connect to your
2
headset.
a
On your Motorola phone, press (Menu)
M
> Settings > Connection > Bluetooth Link >
Audio Devices.
The phone lists Bluetooth devices it finds.
b
Select Motorola H710.
Select OK or Ye s .
c
Your headset is now connected to both
phones. The last paired phone (your second
phone) is now your primary phone for voice
dial functionality.
After you have successfully paired both phones
with your headset, you don't need to repeat
these steps. For daily use, ensure that your
headset is turned ON and that your phone's
Bluetooth feature is ON.
TIPS FOR USING H710
WITH TWO PHONES
Use the following tips when using H710's
multipoint technology:
●
Incoming calls can be answered from both
phones:
– When answering a call, the idle phone is
disconnected from the headset.
– When the call ends, the idle phone is
automatically reconnected to the headset.
●
Last number redial dials the last outgoing call
made from either phone.
●
Voice dial is accessible from either phone via
different key actions:
– For your primary device (last paired
phone), tap the Call button until you hear
the tone.
TROUBLESHOOTING
My headset will not enter pairing mode.
Make sure that any devices previously paired with the
headset are turned off. If the indicator light is flashing in blue,
first turn off the other device, then close and reopen the
headset boom. The indicator light becomes steadily lit in
blue indicating the headset is now in pairing mode.
My phone doesn't find my headset.
Make sure the indicator light on your headset is on (lit in
blue) and steady when your phone is searching for devices
(see step 3).
My headset worked before but now it's not working.
Make sure your phone is on and the Bluetooth feature is
turned on in your phone (see step 2). If the Bluetooth feature
was turned off or was turned on only temporarily, you may
need to restart the Bluetooth feature (see step 2) and pair
your phone and headset again (see step 3).
My headset will not pair with my phone.
Open the boom flip. Press and hold both Volume buttons
and the Call button for more than 10 seconds. The indicator
light flashes blue 3 times and then become steadily lit. The
headset is now in pairing mode (see step 3B) to complete
the pairing process.
– For your secondary device (other paired
phone), tap the Call button and either
Volume button until you hear the tone.
Support.
If you need more help, contact us at
1-877-MOTOBLU or visit us at
www.hellomoto.com/Bluetoothsupport
Page 4
Features and
TURNING HEADSET
ON AND OFF
Functions Guide
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H710.
To turn your headset on, open the headset
boom. The indicator light flashes blue (if
connected with a device) or is steadilly lit (if
ready to be paired).
To turn your headset off, close the
headset boom. The indicator light will turn
off.
Multi-Color
Indicator Light
WEARING THE HEADSET
1
Open the headset boom, then open the
earhook.
Loop the earhook over your ear.
2
Press the headset to your ear.
3
Point the headset boom towards your
4
mouth.
CHANGING FOR USE
ON OTHER EAR
You can wear your H710 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
Open the headset boom,
1
then open the earhook
(90
°
from the headset).
2
Gently lift and pull the
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
remove it.
Flip the headset over.
3
Hook the bottom of the
4
earhook onto the lower
hinge pin, then lift and
pull the top of the
earhook over the upper
hinge pin.
1
Open Earhook
2
Pull Earhook
Up
Hinge
Pin
Page 5
CHANGING VOLUME
QUICK BATTERY
BUTTON ORIENTATION
You can also change the orientation of the
volume buttons on your headset.
Close the boom to turn the headset off.
1
Press and hold down the desired
2
"volume up" button and open the boom.
Keep the button pressed until the
indicator light flashes blue three times.
Volume
Buttons
Call
Button
CHECK
When not in a call, open the boom to check
your headset's battery charge level by
pressing and holding both Volume buttons.
The indicator light displays charge status
until you release the buttons. See below for
details on indicator light and available talk
time based on charge status.
Headset Indicator Available Talk Time
Red Less than 2 hours
Yellow 2 to 4.5 hours
Green Up to 6.5 hours
European Union Directives
C
onformance Statement
Hereby, Motorola declares that
this product is in compliance
with:
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
• All other relevant EU Directives.
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
You can view your product’s Declaration of
Conformity (DoC) to Directive 1999/5/EC (to R&TTE
Directive) at www.motorola.com/rtte. To find your
DoC, enter the product Approval Number from your
product’s label in the “Search” bar on the web site.
MAKING CALLS
Function Action
Make a voice dial call Tap the Call button
(Primary phone) and speak the
name after the tone
Make a voice dial call Tap the Call button
(Secondary phone) and either Voume
button and speak the
name after the tone
End a call Tap the Call button,
and hear a
high-to-low tone
Answer a call Open the boom or tap
the call button (if
boom is ready open),
hear the ring tone,
then a low-to-high
tone
Reject a call Press and hold either
Volume button until
you hear a tone
Note: Some features are phone/network dependent.
Page 6
MAKING CALLS
CONTINUED
AUDIO TONES
Function Action
Redial last call Press and hold the
Call button until you
hear a tone
Answer a second Press and hold the
incoming call Call button (places
first call on hold), and
hear a tone
Reject second incoming Press and hold either
call Volume button until
you hear a tone
Transfer a call from the Press both Volume
headset to the phone buttons and Call
button, and hear a
descending tone
Mute or unmute a call Tap both Volume
buttons until you hear
a mute tone
Note: Your H710 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Audio Tone Headset Status
Ring tone Incoming call
Short tone Phone network not
available
High to low tone End call
Two short tones when Volume at minimum
pressing Volume button or maximum
during a call
Ascending tone Mute enabled
Low tone Mute reminder
(repeated every
15 seconds)
Descending tone Mute disabled
Low to high tone Connection
confirmation/voice
activation
No audio indications; Out of range
deteriorating quality
Two tones Low battery
repeated every minute
INDICATOR LIGHT
With No Charger Plugged In
Headset Indicator Headset Status
Off Power off
Three blue flashes Powering on/off
Steady blue Pairing mode
Quick blue/purple flashes Pairing successful
Quick blue flash Incoming/outgoing call
on primary phone
Slow blue pulse Connected (on a call)
Slow blue flash Standby (not on a call)
Note: After 20 minutes on a call or of inactivity, the light stops
flashing to conserve power, but the headset remains on.
Note: To disable the indicator light, press and hold both
Volume buttons while turnng headset on.
INDICATOR LIGHT
With No Charger Plugged In
Headset Indicator Headset Status
Red flash Idle (not connected
to phone)
Slow purple pulse Connected call muted
Quick red flash Low battery
Tip: Set your primary and secondary phones to different ring
tones to know which phone is ringing when wearing the
headset. See "Tips for using H710 with Two Phones" for
more information.
CONTINUED
INDICATOR LIGHT
With the Charger Plugged In
Headset Indicator Headset Status
Red Battery level less
than 50% charge
Yellow Battery level more
than 50% charge
Green Charging complete
Loading...