Page 1
H700
motorola
Bluetooth
®
Handsfree Headset
Get connected in 4 quick steps.
BEFORE YOU
BEGIN
Before using this product, read the Important Safety and
Legal Information pamphlet and follow its instructions.
Take a moment before you get started to
familiarize yourself with your new
H700 Headset.
Multi-Color
Indicator Light
Volume
Buttons
Speaker
(on reverse
side)
Boom
Microphone
Call
Button
1
CHARGE YOUR
HEADSET
Charge your headset's battery for 2 hours:
Plug the Motorola charger into the end of
1
the headset.
The indicator light turns red when the
battery is charging. It may take up to 1
minute for the indicator light to turn on.
When the headset's battery is fully charged
(about 2 hours), the indicator light turns
green.
2
ENSURE YOUR
HEADSET IS IN
PAIRING MODE
Before you can use your headset, you must pair
(link) it with your phone.
Open the headset boom to initiate easy
pairing. After a few moments, the indicator
light will be steadily lit in purple to indicate
headset is in pairing mode.
Indicator Light
(steadily purple
for pairing mode)
If the headset does not enter pairing mode,
see TROUBLESHOOTING for help.
Disconnect the charger.
2
Note: Headset is not functional while charging.
Page 2
TROUBLESHOOTING
My headset will not enter pairing mode.
Make sure that any devices previously paired
with the headset are turned off. If the indicator
light is flashing in blue, turn off the other device,
then close and reopen the headset boom. The
indicator light becomes steadily lit in purple
indicating the headset is now in pairing mode.
My phone doesn't find my headset.
Make sure the indicator light on your headset is
on (lit in purple) and steady when your phone is
searching for devices (see step 2).
My headset worked before but now it's not
working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone (see step 3).
If the Bluetooth feature was turned off or was
turned on only temporarily, you may need to
restart the Bluetooth feature and pair your
phone and headset again (see steps 2 and 3).
Support.
If you need more help, contact us at
1-877-MOTOBLU or visit us at
www.hellomoto.com//Bluetoothsupport
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
www.hellomoto.com
1-877-MOTOBLU
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
Guide Number: 6809499A88-B
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The use of wireless devices and their
accessories may be prohibited or restricted in certain areas.
Always obey the laws and regulations on the use of these
products. The Bluetooth trademarks are owned by their
proprietor and used by Motorola, Inc. under license. All other
product or service names are the property of their respective
owners.
© Motorola, Inc. 2006.
3
TURN ON BLUETOOTH
ON YOUR PHONE AND
PAIR WITH HEADSET
Your phone's Bluetooth feature is off by
default. To use your headset, turn on the
Bluetooth feature in your phone.
To turn on Bluetooth:
Select (
1
Bluetooth Link > Setup.
2
Scroll to Power.
Press Change.
3
4
Select On.
Select Back.
5
M
Menu) > Settings > Connection >
TURN ON BLUETOOTH
ON YOUR PHONE AND
PAIR WITH HEADSET
Continued
Select [Look for Devices].
7
Note: Do not select STOP--you will automatically be
taken to the next screen.
Select Motorola H700.
8
Select Ye s to bond.
9
Enter the passkey 0000 and select OK.
10
When your headset and phone are successfully
paired, the indicator light changes from steadily
lit to flashing blue.
Select Handsfree.
6
Note: These steps are for most Motorola phones. For other
phones, see your phone's user's guide.
Note: These steps are for most Motorola phones. For other
phones, see your phone's user's guide.
Page 3
TEST AND USE
4
Your phone and headset are now paired and
ready to make and receive calls. To confirm they
are operating properly, make a call:
Place the headset over your ear. See
1
"Wearing the Headset" on the reverse side
of this guide.
On your phone, dial the number you want
2
to call and press the Send key.
If your phone and headset are successfully
3
paired, you will hear ringing on the headset.
After you have successfully paired your phone
and headset, you don't need to repeat these
steps. For daily use, ensure that your headset is
turned ON and that your phone's Bluetooth
feature is ON.
USING YOUR H700
See
Features and
Functions Guide
on the reverse side
for information on
using your H700
To save battery power, turn OFF the headset
when you don't use it for an extended time by
closing the boom.
Features and
Functions Guide
H700
Bluetooth®
Handsfree Headset
IMPORTANT:
Be sure to first follow the
TURNING HEADSET
ON AND OFF
To turn your headset on, open the headset
boom. The indicator light flashes blue.
To turn your headset off, close the
headset boom. The indicator light will turn
off.
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H700.
Multi-Color
Indicator Light
Page 4
WEARING THE
CHANGING FOR USE
HEADSET
1
Open the headset boom, then open the
earhook.
Loop the earhook over your ear.
2
3
Press the headset to your ear.
Point the headset boom towards your
4
mouth.
ON OTHER EAR
You can wear your H700 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
Open the headset boom,
1
then open the earhook
°
from the headset).
(90
2
Gently lift and pull the
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
remove it.
Flip the headset over.
3
Hook the bottom of the
4
earhook onto the lower
hinge pin, then lift and
pull the top of the
earhook over the upper
hinge pin.
1 Open Earhook
2 Pull Earhook
Up
Hinge
Pin
CHANGING VOLUME
BUTTON ORIENTATION
You can also change the orientation of the
volume buttons on your headset.
Turn the headset power off.
1
Press the Call button until the indicator
2
light becomes steadily lit in purple, then
press the Volume button you want to
assign as the "volume up" button.
Call
Volume
Buttons
Button
European Union Directives
Conformance Statement
Hereby, Motorola declares that this
product is in compliance with:
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
• All other relevant EU Directives.
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
You can view your product’s Declaration of Conformity
(DoC) to Directive 1999/5/EC (to R&TTE Directive) at
www.motorola.com/rtte. To find your DoC, enter the
product Approval Number from your product’s label in
the “Search” bar on the web site.
Page 5
MAKING CALLS
MAKING CALLS
CONTINUED
Function Action
Make a voice dial call Tap the Call button
and speak the
name after the tone
End a call Tap the Call button
Answer a call Open headset boom
or tap the Call button
(if boom is already
open)
Ignore a call Press and hold the
Call button until you
hear a beep
Redial last call Press and hold the
Call button until you
hear a beep
Note: Your H700 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Function Action
Answer a second Press and hold the
incoming call Call button (places
first call on hold)
Toggle between two Press and hold
active calls the Call button
Join a 3-way call Press and hold
both Volume buttons
Put an active call on Press and hold the
hold or resume a call Call button until you
on hold hear a beep
Transfer a call from the Open headset boom
phone to the headset
Disable the Press and hold
indicator light both Volume
buttons for 3 to 4
seconds
Mute or unmute a call Tap both Volume
buttons
Note: Some features are phone/network dependent.
INDICATOR LIGHTS
With the Charger Plugged In
Indicator Light Headset Status
Red (steady) Charging (less than
80% charged)
Yellow (steady) Charging (more
than 80% charged)
Green (steady) Charging complete
With No Charger Plugged In
Indicator Light Headset Status
Off Power off
Purple (steady) Pairing mode/
Volume button
orientation
Red Battery low
Blue (10 rapid flashes) Pairing successful
Blue (slow pulse) Connected (on a call)
Blue (quick flash) Standby (not on a call)
Note: After 5 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.
AUDIO TONES
The audio tones provide information about your
headset status.
Audio Tone Headset Status
Single high tone when Volume at minimum
pressing Volume button or maximum
Five rapid high tones Low battery
repeated every 60 sec.
No audio indications; Out of range
deteriorating quality
Ring tone Incoming call
Single high tone Pairing confirmation
Single low tone Voice activation
Dual high/low tone Voice tag not
recognized
Single high tone End call
Low to high tone Phone network
not available
Two ascending tones Mute enabled
Two descending tones Mute disabled
Loading...