Motorola DC800 Quick Start Guide

			Before using this product, read the Important Safety and Legal
			Information pamphlet and follow its instructions.
			Follow the numbered steps to connect
			and use a Motorola Bluetooth® DC800
			Home Stereo Adapter.
DC800			Note: The DC800 Home Stereo Adapter is
			a Class 1 Bluetooth device. Bluetooth
Bluetooth®			features and Bluetooth Class 1 power
			levels are not allowed for outdoor operation
Home Stereo Adapter
			in France. To avoid unlawful interference
			with radio signals, do not use the Bluetooth
Get Connected in			features in France unless you are indoors.
			Note: To operate with the DC800 Home
5 Quick Steps
			Stereo Adapter, your Bluetooth audio
1 - 2 CONNECT			device must support A2DP Profile
			capability.
3 - 4 PAIR
5 TEST AND			Note: To maintain compliance with RF
USE
			exposure guidelines, you must keep the
			DC800 Home Stereo Adapter at least 20
			centimeters (8 inches) away from any
			person.

		1	AUDIO	2	POWER
			CONNECTIONS		CONNECTIONS
	Make the following audio connections to your			Make the following power connection to
	stereo adapter (using the supplied cables):			your stereo adapter:
		Audio Out
			Jacks
			Audio In
			Jacks	Power Jack
	1	Connect the Audio Out jacks on the stereo
		adapter to unused Audio In jacks on your		1 Plug the included AC power supply into
		home stereo system.
	2	Connect the Audio In jacks on the stereo		the Power Jack on the stereo adapter.
				2 Plug the other end of the AC power supply
		adapter to unused Audio Out jacks (such as
		Tape Out) on your home stereo system.		into a wall outlet.

Note: If your home stereo does not support Line Out audio, you may have to connect through the headphone jack with the included RCA-to-headphone cable.

Note: To stream music from your phone (when equipped with 2.5mm stereo output jack), use the included RCA-to- 2.5mm cable to connect to the adapter's Audio In jacks.

	3	PAIR WITH			Motorola, Inc.
					Consumer Advocacy Office
		BLUETOOTH HEADSET			1307 East Algonquin Road
					Schaumburg, IL 60196
Enable your stereo adapter to transmit music to
your Bluetooth wireless headphone:					www.hellomoto.com
	Note: This guide does not provide steps for pairing your				1-877-MOTOBLU
	stereo adapter with a Bluetooth USB PC Adapter or a				1-800-331-6456 (United States)
	Bluetooth-enabled PC. Consult the USB Adapter or PC's				1-888-390-6456 (TTY/TDD United States for
	user guide for details on completing this step.				hearing impaired)
1	Holding your headphone close to the				1-800-461-4575 (Canada)
	stereo adapter, place the headset into				Part Number: 6809494A97-C
	pairing mode.
	If using the Motorola HT820 Bluetooth				MOTOROLA and the Stylized M Logo are registered in the US
	Stereo Headphone, place in pairing mode
					Patent & Trademark Office. The Bluetooth trademarks are
	by pressing and holding the headphone's
					owned by their proprietor and used by Motorola, Inc. under
	Call button for approximately 6 seconds
					license. All other product or service names are the property of
	until the indicator light is solidly lit. For
					their respective owners.
	other products, refer to your headset's
	user's guide for details.				The use of wireless devices and their accessories may be
2	Turn on the stereo adapter by pressing in				prohibited or restricted in certain areas. Always obey the laws
					and regulations on the use of these products.
	the Power button. After a few moments,
	the Pairing Button indicator light begins
	blinking to indicate the power is on.				© Motorola, Inc. 2005.

	3 PAIR WITH BLUETOOTH				4	PAIR WITH
						BLUETOOTH PHONE
	HEADSET
		CONTINUED		Enable your stereo adapter to receive music
				from the built-in MP3 player of your Bluetooth
				A2DP-capable phone:
				Note: These steps are for most Motorola phones. Certain phones
				require additional steps to enable stereo audio streaming (A2DP
				Profile). See your phone's user's guide to verify proper steps.
				1	Turn on the stereo adapter by pressing in the
	Pairing Button with	Power Button			Power button. After a few moments, the
					Pairing button indicator light begins blinking
	Indicator Light
					to indicate the power is on.
	3 Press and hold the Pairing button on the			2	From the phone, perform a Bluetooth device
	stereo adapter until the indicator light
					discovery while holding it close to the adapter.
	remains solidly lit (about 5 seconds).
					The phone lists Bluetooth devices it finds.
	The stereo adapter searches for Bluetooth
				3	Select Motorola DC800.
	devices. When the stereo adapter finds the
	headphone, the indicator light rapidly flashes			4	Select OK or Yes to pair your stereo adapter
	indicating that pairing is successful.				and phone.
	Once the connection is established, the			5	Enter the passkey: 0000
	indicator light changes to a slower, pulsing			6	Select OK. The Pairing button indicator light
	light.				flashes rapidly to indicate pairing is successful.