®
HDP1800
High Definition PowerCenter™
PowerCenter™ Haute Définition
Manuel du propriétaire
TABLE OF CONTENTS |
Page |
|
|
Important Safety Information |
ii |
Proper Grounding and Installation |
|
A Note from The Head Monster |
2 |
Monster Clean Power |
3 |
T2 Circuitry |
4 |
The Minds Behind The Monster PowerCenter Design. |
5 |
Monster HDP1800 PowerCenter Features |
6 |
Hook-Up Guide |
8 |
High Definition Digital Outlets |
8 |
Analog Audio Outlets |
9 |
Ultra-High Current Audio PLC-Compatible Outlets |
10 |
Coaxial Connections |
1 |
Phone and Network Connections |
12 |
Troubleshooting |
13 |
Specifications |
16 |
Warranty Information |
17 |
Owner’s Manual in French (Manuel du propriétaire en Français) |
23 |
i
IMPORTANT SAFETY INFORMATION
Please read and observe the following safety points at all times.
WARNING – Power Sources
Do not plug this PowerCent into a power outlet that differs from the source indicated for safe use on the PowerCenter. If you don’t know the type of electrical power that is supplied to your home, consult your local power company or a qualified electrician.
WARNING – Grounding and Polarization
A.Do not force your PowerCente plug into an outlet that is not designed to accept a three-wire grounded-type AC plug (a three-prong plug).This plug is designed to be inserted into a grounded-type outlet only. If this plug doesn’t fit directly inside your outlet, do not attempt to force it into the outlet. Never attempt to dismantle the plug in any way (or to alter the power cord). Do not attempt to defeat the grounding feature by using a 3-to-2 prong adapter. If you have questions about grounding, consult your local power company or a qualified electrician.
B.If you use rooftop devices such as satellite dishes, antennas, or any other component with wire that connects to your PowerCente , be sure the wire(s) is properly grounded. This protects against voltage surges and static charges.
C.Do not place any antenna near overhead power lines or any other power circuit. Do not touch any power line or power circuit. Doing so may cause severe physical injury or possibly death.
WARNING – Liquid: Avoiding Electrical Shocks
A.Do not operate your Monster PowerCenter if liquid of any kind is spilled onto or inside the unit.
B.Do not operate your Monster PowerCenter near rain or water that’s spilled or contained (e.g., bathtub, kitchen or sink).
WARNING – Power Cord Safety
A.When routing your PowerCenter’s AC power cord, do not place it near heavy foot traffic areas (e.g., hallways, doorways, and floors). Do not create a trip hazard with the power cord.
B.If your power cord’s protective jacket begins to rip or fray, exposing the internal wiring, shielding, etc., disconnect it from the AC power source and discontinue use of the Monster PowerCenter immediately. See the Warranty Information section of this owner’s manual for important details.
ii
WARNING – No User Serviceable Parts Inside
If, for any reason, your PowerCenter is not operating properly, do not remove any part of the unit (cover, etc.)
for repair. Unplug the unit and consult the Warranty Information section of this owner’s manual for important details.
CAUTION – Exposure To Heat
Do not expose your PowerCenter to direct sunlight or place it near wall heaters, space heaters, or any enclosed space prone to temperature increase.
CAUTION – Proper Cleaning
In general, the only cleaning necessary for your Monster PowerCenter is a light dusting. Unplug the PowerCenter from the wall outlet before cleaning it. Do not use any type of liquid or aerosol cleaners.
iii
PROPER GROUNDING AND INSTALLATION
WARNING – Proper Grounding
Monster PowerCenters require a properly grounded outlet for safety and to protect connected equipment.
If you’re not sure if your home’s electrical wiring is properly grounded, have it checked by a qualified electrician.
Important Note – Proper Power and Protection
To completely protect your equipment against electrical surges, every AC power cable coaxial cable, network line, and phone line in the system must be connected to an appropriate PowerCenter outlet or port.
Important Note Proper Protection and the Limited Connected Equipment Warranty
The U.S. $350,000 Limited Connected Equipment Warranty becomes invalid if any wire (AC, coax, phone or network) or audio or video interconnect leading into the equipment comes from a component that is not properly protected by the PowerCenter. See the Warranty Information section
of this owner’s manual for important details.
1
A NOTE FROM THE HEAD MONSTER
Dear Enthusiast,
THANK YOU for purchasing the Monster High Definition PowerCenter1800.
The home theater high definition revolution is in full swing. Modern HDTVs and digital audio equipment offer stunning picture and sound with a level of precision that was impossible just a few years ago. Unfortunately, high definition digitalAV components are just as vulnerable to dirtyAC power and surge problems as their predecessors.
As a long-time audiophile and serious home theater enthusiast, I always knew problematicAC power could seriously degrade picture and sound quality. Ordinary unfilteredAC power contains electromagnetic and radio frequency noise that degrades the picture and sound quality of your home theater. Monster PowerCenters feature patented Monster Clean Power filter circuitry that virtually stops the electromagnetic pollution that goes right through typical
surge protectors. Clean Power circuitry filters both externalAC powerline noise and also dramatically reduces noise generated byAV equipment connected to the PowerCenter.
The HDP1800 incorporates Monster HD Clean Power filters, which are specifically engineered for today’s digital high definition components.This reflects our commitment to creating performance-enhancing solutions for the latest audio and video equipment so
you can enjoy the best HD picture and digital sound quality from modern home theater systems.The HDP1800 also provides complete protection and filtering for legacy analog and high powerAV components.
These days, home theater components are better than ever, providing thrilling and dramatic digital sound and razor sharp high definition picture.We know your new HD PowerCenter will help bring it all together with Clean Power and superior surge protection.With Monster Power you’ll enjoy the best possible sound and picture, and that’s what high definition home theater is all about.
Noel Lee,
The Head Monster
2
PATENTED MONSTER CLEAN POWER STAGE 2
Monster Clean Power performs two tasks that are vital to maintaining optimum home theater performance:
1) noise filtration and 2) noise isolation.The higher the Clean Power stage number (1-5), the more sophisticated and advanced the filters are that reject noise generated on the AC powerline. In addition, the higher the Clean Power stage number, the more isolation that exists between connected equipment for maximum rejection of component generated noise.
Monster PowerCenters featuring Clean Power circuitry are each designated with a Clean Power Stage.
The High Definition PowerCenter1800 incorporates Monster HD Clean Power filters and Clean Power Stage 2 circuitry which filters both AC powerline noise and reduces noise generated by your connected equipment. Monster Clean Power Stage 2 features two ultra-advanced isolated filters optimized for high definition digital and audio components, and ultra high current audio outlets that provide the best possible AC powerline noise rejection and inter-component for improved component-generated noise rejection.These features make the High Definition PowerCenter1800 ideal for high definition digital AV systems and home theaters.To learn more about patented Monster Clean Power and the complete product family of PowerCenters, voltage stabilizers, and amplifiers, please visit MonsterPower.com
Actual spectrum analyzer |
AC power line filtered |
|
photo of AC power pollution |
by Monster Clean Powe |
3 |
|
|
PATENTED MONSTER T2 TECHNOLOGY
The Monster HDP1800 features exclusive Monster T2 technology.T2 is an active electronic microprocessor-controlled circuit that sits in front of the surge protection circuitry in select Monster Power products.T2 monitors the line, neutral and ground lines and automatically disconnects the PowerCenter from the AC power line when a long duration low-voltage sag or high-voltage swell occurs (continuous voltage below 80Vrms or above 132Vrms).
When the voltage sags or swells to these potentially damaging levels, ultra-fast T2 auto-disconnect protection circuitry shuts down the Monster PowerCenter for 15 seconds.When the under-voltage or over-voltage condition returns to normal, T2 reconnects the PowerCenter to the electricity and resets to full operation after 15 seconds. If the power fault condition does not clear, the T2 comparator circuit keeps the unit shut down.
Unlike ordinary power management devices,T2 will shut down your PowerCenter before the MOVs (Metal Oxide Varistors) and thermal fuses sense an overload condition and sacrifice themselves to protect your connected components.
This will extend the PowerCenter’s life, while providing the system protection you need.
4
THE MINDS BEHIND THE MONSTER POWERCENTER DESIGN
Richard Marsh – Richard developed Monster’s patented Clean Power circuitry, and is also responsible for several other groundbreaking designs including the high-end audio balanced circuit design, the MultiCap internal bypass capacitor, and the Servo-DC feedback concept in power amplifiers – a concept that is used by virtually every amplifier manufacturer today.
Demian Martin – Demian helped create several innovative AC power solutions. He was the co-founder
of Spectral Audio and was the chief designer of their many pioneering designs for amplifiers, D/A converters, and other high-end audio designs. He now brings his expertise to Monster Power’s elite research and development team.
Noel Lee – Noel Lee, The Head Monster, is best known for popularizing the concept of high performance audio cable 25 years ago with his creation of Monster Cable. Originally a laser-fusion design engineer at Lawrence Livermore National Laboratory and later a touring musician, Noel has invented or co-invented over 250 U.S. and international patents.
Monster Power is Noel’s realization of a long-nurtured vision of making affordable power solutions that deliver the best possible sound and picture.
Tony DiChiro was one of the founders of Kinergetics Research in 1971.
Kinergetics developed numerous patented technologies that advanced the state of the art in audio technology, and released highly acclaimed home theater products.
Kinergetics also debuted the first highend surround sound processor with THX certification. Tony currently heads up the
R&D team at Monster Cable where he continues to develop advanced products with cutting edge features.
5
HDP 1800 FRONT VIEW
HDP 1800
REAR VIEW
MONSTER HDP 1800 POWERCENTER FEATURES
12
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
4 |
|
5 |
6 |
7 |
8 |
|
|
9 |
|
|
|
10 |
11 |
12 |
13 |
14 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
����� |
|
|
|
��� |
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
18 |
|
|
|
|
|
|
|
|
15 16 17
6
HDP1800 POWERCENTER FEATURES
FRONT
1. |
“Protection On” Indicator |
7. |
Display Dimmer Button |
2. |
“Wiring OK” Indicator |
8. |
Power ON/OFF Switch (for Switched Outlets) |
3. |
“Clean Power On” Indicator |
9. |
High Definition Digital Filter (Unswitched Outlets) |
4. |
“Ground OK” Indicator |
10. Analog Audio Filter (Unswitched Outlets) |
|
5. |
Abnormal Voltage Indicator |
11. |
Ultra-High Current Audio Filter (Switched Outlets) |
6. |
Digital Display for Voltage |
|
|
REAR
12. |
Phone Line Surge Suppression |
16. |
Input AC Circuit Breaker |
13. |
Satellite Surge Suppression |
17. |
Ground Isolation Cable and Antenna |
14. |
Ground Screw |
18. Ultra-High Current PowerLine™ 100 AC Power Cable |
15. Network Line Surge Suppression
7
HOOK-UP GUIDE
High-Definition Digital Outlet Hook-Up
These outlets have a special filter circuit that is optimized to reduce interference to your high-definition digital components.
A)Attach a Monster Power identification label to each component’s power cord before you plug it into the appropriate color-coded PowerCenter outlet.
B)Plug each component’s power cord (HDTV, DVD, etc.) into the PowerCenter’s corresponding outlet. For components not listed, determine if they are audio, video, high-definition digital or ultra-high current audio components, and use a corresponding outlet for best performance.
IMPORTANT NOTE
It does not harm analog audio, video, or high current audio components to be connected to the high-definition
digital outlets. However, for best performance, we recommend plugging in only digital components to the high-definition digital outlets.
��� ��������� |
|
|
|
|
|
High Defi nition Digital Outlets
8
HOOK-UP GUIDE
Analog Audio Outlet Hook-Up
These outlets have a special filter circuit that is optimized to reduce interference to your audio components.
A)Attach a Monster Power identification label to each component’s power cord before you plug it into the appropriate color-coded PowerCenter outlet.
B)Plug each component’s power cord (Receiver, Processor, etc.) into the PowerCenter’s corresponding outlet. For components not listed, determine if they are audio, video, digital, or ultra-high current audio,
and use a corresponding outlet for best performance.
IMPORTANT NOTE
It does not harm video, digital, or high current audio components to be connected to the analog audio outlets.
However, for best performance, we recommend plugging in only analog audio components to the analog audio outlets.
��� ��������� ������� |
��������� |
����� |
|
|
|
Analog Audio Outlets
9
HOOK-UP GUIDE
Ultra-High Current Audio PLC-Compatible Outlet Hook-Up
These outlets are designed to deliver maximum current to power hungry components like amplifiers and pre-amplifiers.
A)Attach a Monster Power® identification label to each component’s power cord before you plug it into the appropriate color-coded PowerCenter outlet.
B)Plug each component’s power cord (Amplifier, etc.) into the PowerCenter’s corresponding outlet. For components not listed, determine if they are audio, video, digital, or ultra-high current audio, and use a corresponding outlet for best performance.
IMPORTANT NOTES
It does not harm analog audio, video, or digital components to be connected to the ultra-high current
audio outlets. However, for best performance, we recommend plugging in only high-current audio components to the ultra-high current audio outlets.
PLC or Power Line Communications is a home networking solution that uses your home’s AC power wiring
for data transfer. These outlets will allow PLC signals to pass through while still actively filtering noise and interference.
��� ��������� ������� |
��������� |
����� |
|
|
|
High Current Audio
PLC-Compatible Outlets
10
HOOK-UP GUIDE
Coaxial Connections Hook-Up
Coaxial Connections provide surge protection against damaging voltage surges and spikes on the incoming coax cable.
The HDP1800 Cable/TV coaxial connection also features ground loop isolation to dramatically reduce unwanted noise.
Only a Cable TV line should be connected to the PowerCenter’s Cable TV coaxial connection. Connecting a Satellite or other cable to the PowerCenter’s Cable TV connection may result in compromised reception.
Protect TV/Cable and Satellite Connections as follows:
From properly grounded |
From properly grounded |
TV/Cable Line |
Satellite Dish |
To TV/Cable Box |
To Satellite Receiver |
NOTES: You may need additional coaxial cables to connect the HDP1800 to your components.
To ensure complete power surge protection, all lines that connect to your AV components need to be connected to surge protected connections on the PowerCenter.
11