Mitsubishi Outlander III (2018) Owner’s Manual

Outlander

2018 / OWNER’S MANUAL

Table of contents

1
2
3
4
5
6
7
8

9
10
11
12

Overview

Quick index

General information

Seat and restraint systems

Features and controls

Driving safety

Comfort controls

For emergencies

Vehicle care and maintenance

Customer assistance/Reporting Safety Defects

Specifications

Alphabetical index

Instruments and controls

1

Combination headlights and dimmer switch P.5-207
Automatic high beam system switch
(if so equipped) P.5-211
Turn signal lever P.5-217
Front fog light switch (if so equipped)
P.5-218

Steering wheel remote control switches
[Refer to the separate owner’s manual.]

Active stability control
(ASC) OFF switch P.5-101

Supplemental restraint system
(SRS) - airbag (for driver’s
seat) P.4-35, 4-42
Horn switch P.5-227

Instrument cluster
P.5-154

Windshield wiper and washer
switch P.5-219
Rear window wiper and
washer switch P.5-223

Cruise control switches
P.5-103, 5-107

Steering wheel height and reach adjustment lever P.5-57

Engine switch (if so
equipped) P.5-18

Driver’s vents
P. 7 -2

Sportronic steering wheel paddle
shifter (if so equipped)
P.5-72, 5-80

Driver’s vents P.7-2

Multi information display
switch (if so equipped)

P.5-157
Headlight leveling switch
(if so equipped) P.5-216

Driver’s side power liftgate switch
(if so equipped) P.5-41

Fuse box P.9-26

Lane Departure Warning
(LDW) switch (if so equipped)
P.5-135

Forward Collision Mitigation
system (FCM) ON/OFF
switch (if so equipped)
P.5-122

Supplemental restraint system (SRS) - front knee airbag
(for driver’s seat) P.4-35, 4-42

Ignition switch (if so equipped)
P.5-63

Camera switch (if so equipped)
P. 5-144

Instruments and controls

N00100202788

Overview

1-1

1

Audio (if so equipped)
[Refer to the separate owner’s manual.]
Multi Around Monitor (if so equipped) P.5-144

Hazard warning flasher switch
P.5-218

Electric rear window defogger switch P.5-225
Wiper deicer switch (if so equipped) P.5-224

Fuel tank filler door release lever
P. 3- 3

Air conditioner P.7-5

Hood release lever
P. 9 -3

Floor console box P.5-240
Arm rest
12 V power outlet P.5-230
USB input terminal P.5-227

Cup holder P.5-242

12 V power outlet P.5-230

Power liftgate main switch (if so equipped)
P.5-40

Key slot (if so equipped)
P.5-27

Passenger’s vents
P. 7- 2

Passenger’s airbag off indicator P.4-40

Front passenger seat belt warning light
P.4-23

Heated steering wheel
switch (if so equipped)
P.5-226

Blind Spot Warning (BSW)
switch (if so equipped)
P.5-126

Camera switch (if so equipped)
P.5-148

Instruments and controls

Overview 1-2

Instruments and controls

1

Supplemental restraint system (SRS) - airbag
(for front passenger’s seat)
P. 4-35, 4-42

Glove compartment P.5-239
Card holder P.5-239

Selector lever
P.5-68, 5-75

Drive mode-selector
(if so equipped) P.5-83
S-AWC drive mode-selector
(if so equipped) P.5-86

Parking brake lever P.5-53

Heated seat switch
(if so equipped)
P. 4 -8

Selector lever
P.5-68, 5-75

Electric parking brake switch P.5-54

Brake auto hold
switch P.5-93

Drive mode-selector
(if so equipped)
P.5-83

Electric parking brake typeParking brake lever type

Heated seat switch
(if so equipped)
P. 4 -8

1-3 Overview

Interior

1

Sun visors P.5-229
Vanity mirror P.5-229
Card holder P.5-229

Supplemental restraint system (SRS) - side airbag
(for front seats) P.4-35, 4-46

Sunglasses holder (if so equipped)
P.5-242

Adjustable seat belt shoulder anchor P.4-24
Seat belts P.4-18

Cargo room light
P.5-238, 9-33

Electric remote-controlled outside rearview mirrors switch P.5-61

Lock switch P.5-50

Power door lock
switch P.5-36

Power window switch
P.5-49

Second row seats P.4-8

Third row seat (7 persons)
P. 4- 1 0

Dome light (rear) P.5-237

Inside rearview mirror P.5-57

HomeLink

®

Wireless Control System

(if so equipped) P.5-231

Front seats P.4-4

Interior

N00100302473

Overview 1-4

1

Assist grips P.5-246
Coat hook P.5-246

Bottle holder P.5-243

Sunroof switch
(if so equipped) P.5-51

Head restraints P.4-11

Arm rest P.4-10
Cup holder P.5-243

Cargo area cover (if so equipped)
P.5-244

Supplemental restraint system (SRS) - curtain
airbags P.4-35, 4-47

Dome light (front)/Reading
lights P.5-236

Downlight
P.5-207

Hands-free microphone
(if so equipped)

Interior

1-5 Overview

Luggage area

1

Jack P. 8-5
Tools P.8-5

Luggage hooks
P.5-246

Luggage floor box P.5-240

Tether anchorages for child restraint system P.4-30

12 V power outlet
P.5-230

Luggage area

N00100501579

Overview 1-6

Outside (Front)

1

Sunroof (if so equipped) P.5-51

Windshield wipers P.5-219

Engine hood P.9-3

Front fog lights (if so equipped) P.5-218, 9-32, 9-36

Outside rearview mirrors P.5-60
Side turn-signal lights (if so equipped)
P.5-217, 9-32, 9-36
Side-view camera (if so equipped)
P.5-144

Fuel tank filler P.3-3

Power window P.5-49

Front turn-signal lights
P.5-217, 9-32, 9-36

Front turn signal lights
P.5-217, 9-32, 9-36

Headlights, low beam
P.5-207, 9-32, 9-34

Parking lights P.5-207, 9-32, 9-36
Daytime running lights
P.5-207, 9-32, 9-36

Headlights, low beam
P.5-207, 9-32, 9-34

Parking lights P.5-207, 9-32, 9-36
Daytime running lights
P.5-207, 9-32, 9-36

Headlights, high beam
P.5-207, 9-32, 9-35

Headlights, high beam
P.5-207, 9-32, 9-35

Halogen headlights type LED headlights type

Front side-marker lights
P.5-207, 9-32, 9-35

Front side-marker lights
P.5-207, 9-32, 9-35

Sensor (if so equipped) [for Forward Collision Mitigation System
(FCM), Lane Departure Warning System (LDW) and Automatic
high beam system] P. 5-118, 5-134, 5-211
Rain sensor (if so equipped) P.5-219

Front-view camera (if so equipped) P.5-144

Outside (Front)

N00100602782

1-7 Overview

1

Outside (Rear)

Keyless entry system (if so equipped) P.5-7, 5-30
F.A.S.T.-key (Free-hand Advanced Security Transmitter) (if so equipped)
P.5-13
Locking and unlocking P.5-34

Tires P.9-15
Tire pressure monitoring system
P.5-137
Tire inflation pressures P.9-19
Changing tires P.8-6
Tire rotation P.9-20
Tire chains P.9-22
Size of tires and wheels P.11-7

Stop lights P.5-207, 9-32, 9-37

Rear turn signal lights P.5-217, 9-32, 9-37

Spare tire P.8-7

Back-up lights P.9-32, 9-38

License plate lights
P.5-207, 9-32, 9-39

Rear-view camera
P.5-142, 5-144

Rear window wiper
P.5-223

High-mounted stop light
P.9-32

Antenna

Liftgate (if so equipped) P.5-38
Power liftgate (if so equipped) P.5-39

Rear side-marker lights P.5-207, 9-32

Tail lights P.5-207, 9-32, 9-37

Outside (Rear)

N00100602737

Overview 1-8

2

If this warning light comes on or flashes while you’re driving...

NOTE

If this warning light comes on or flashes while you’re driving...

N00200702289

 For information regarding warning displays in the multi-information display (Color liquid crystal display type), refer to “Multi-information display” on

page 5-155.

 These warning lights will come on for a few seconds for a bulb check when the ignition switch is first turned to “ON” or the operation mode is put in ON.

Warning l igh ts Do this Ref. Page

 Park your vehicle in a safe place and stop the engine.

Charging system warning light

Oil pressure warning light

(Vehicles equipped with mono-color

liquid crystal display)

or

Brake warning light (red)

Contact your Mitsubishi Motors dealer or a repair facility of your choice for assis­tance.

 Park your vehicle in a safe place and stop the engine, then check the engine oil

level.
If the light comes on while the engine oil level is normal, have the system checked
at an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon
as possible.

 If this light comes on while driving, check to see that the parking brake is fully

released.

 If this light stays on after releasing the parking brake, immediately stop and check

the brake fluid level.

 If the brake fluid level is correct, there may be a system malfunction. Avoid hard

braking and high speed, and contact an authorized Mitsubishi Motors dealer or a
repair facility of your choice for assistance.

P. 5-204

P. 5-205

P. 5-203

Quick index

2-1

If this warning light comes on or flashes while you’re driving...

2

Warning lights Do this Ref. Page

 If the warning light comes on during driving, there is the possibility that the parking

brake cannot be operated or released. Immediately stop the vehicle in a safe place,
and contact an authorized Mitsubishi Motors dealer or a repair facility of your

Electric parking brake warning light

(yellow) (if so equipped)

choice for assistance.

P. 5-203

Selector lever position indicator in the
instrument cluster blinks rapidly (once

per second)

(Vehicles equipped with mono-color

liquid crystal display)

or

Engine malfunction indicator

(“SERVICE ENGINE SOON” or

“Check engine light”)

2-2 Quick index

 Park your vehicle in a safe place.

Idle the engine until the selector lever position indicator stops blinking.
If the indicator continues blinking, contact an authorized Mitsubishi Motors dealer
or a repair facility of your choice immediately.

 Although your vehicle will usually be drivable and not need towing, have the

engine system checked at an authorized Mitsubishi Motors dealer or a repair facility
of your choice as soon as possible. If the vehicle is not drivable, contact emergency
roadside assistance at 1-888-648-7820 (for vehicles sold in U.S.A.) or 1-888-576­4878 (for vehicles sold in Canada), an authorized Mitsubishi Motors dealer, or local
towing company for assistance.

P. 5-70,

5-78

P. 5-204

If this warning light comes on or flashes while you’re driving...

2

Warning l igh ts Do this Ref. Page

 If this light comes on while the engine is running, it may become harder to turn the

Electric power steering system (EPS)

warning light

(Vehicles equipped with mono-color

liquid crystal display)

Anti-lock braking system warning

light

steering wheel. Have your vehicle inspected at an authorized Mitsubishi Motors
dealer or a repair facility of your choice as soon as possible.

 When this light comes on, the anti-lock braking system is not functioning and only

the ordinary braking system is functioning.

 Park your vehicle in a safe place and stop the engine.

Test the system as described on page 5-98.

 If the light does not go out after the test, or if it comes on again, we recommend that

you have the system checked at an authorized Mitsubishi Motors dealer or a repair
facility of your choice as soon as possible.

P. 5-99

P. 5-98

SRS warning light

Selector lever position indicator in the

instrument cluster blinks slowly (once

every 2 seconds)

(Vehicles equipped with mono-color

liquid crystal display)

 Immediately have the airbag and the pre-tensioner seat belt system checked at an

authorized Mitsubishi Motors dealer.

 Have the automatic transaxle checked at an authorized Mitsubishi Motors dealer or

a repair facility of your choice immediately.

Quick index 2-3

P. 4-41

P. 5-70,

5-78

If this warning light comes on or flashes while you’re driving...

2

Warning lights Do this Ref. Page

 Park your vehicle in a safe place and stop the engine.

Restart the engine and check whether the indicator goes out.

and

ASC indicator and ASC OFF indicator

ASC indicator

Tire pressure monitoring system warn-

ing light

 If the indicator does not go out, or if it comes on again, have your vehicle inspected

by an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon
as possible.

 When this indicator comes on, the active stability control is not functioning and

normal operation of the vehicle will not be affected.

 Park your vehicle in a safe place and stop the engine.

Restart the engine and check whether the indicator goes out.

 If the indicator does not go out, or if it comes on again, have your vehicle inspected

by an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon
as possible.

 When this indicator comes on, the hill start assist is not functioning.

Start off carefully on a steep uphill slope.

 If the warning light comes on, you should stop and adjust the tires to the proper

inflation pressure as soon as possible.
(See “Tire inflation pressures” on page 9-19.)
Once adjustments have been made, the warning light will go off after a few minutes
of driving.

 If the warning light blinks for approximately 1 minute and then remains continu-

ously illuminated, the system is not operating properly. If the system returns to nor­mal, the warning light will go off. If the warning light does not go off, have the
vehicle inspected at an authorized Mitsubishi Motors dealer.

P. 5-102

P. 5-96

P. 5-137

LED headlight warning light

2-4 Quick index

 If the warning light comes on, there may be a malfunction in the LED headlight

unit.
Have the vehicle inspected at an authorized Mitsubishi Motors dealer or a repair
facility of your choice.

P. 5-210

If this problem occurs...

2

If this problem occurs...

N00200901936

Problem Do this Ref. Page

Unable to turn the key.
(except for vehicles equipped
with the F.A.S.T.-key)

The engine does not start when
the engine switch is pressed.
(for vehicles equipped with the
F.A.S .T. -k ey)

Will not turn from “LOCK” to “ACC”. (Vehicles with steering lock system)

Turn the key while turning the steering wheel in either direction.

Will not turn from “ACC” to “OFF” or “LOCK”.

Check the position of the selector lever.
The key cannot be removed unless the selector lever is set to the “P” (PARK) position.
On vehicles with steering lock system, push the key in at the “ACC” position and keep it
depressed until it is turned to the “LOCK” position.

Make sure the F.A.S.T.-key is in the vehicle.
Make sure the selector lever is in the “P” (PARK) position, and then press the engine switch
while depressing the brake pedal.

P. 5-65

P. 5-64

P. 5-25

The F.A.S.T.-key does not oper­ate.
(for vehicles equipped with the
F.A.S .T. -k ey)

Insert the F.A.S.T.-key into the key slot of the instrument panel, and then start the engine or
change the operation mode. Use the emergency key to lock and unlock the driver’s door.

Quick index 2-5

P. 5-27,

5-28

If this problem occurs...

2

Problem Do this Ref. Page

Cannot shift the selector lever
from the “P” (PARK) position.

The windows are fogged up.

Shift the selector lever while pressing the brake pedal.
Check that the ignition switch or the operation mode is in ON.

P. 5-68

The engine does not start.
The lights do not come on.
The lights are dim.
The horn does not honk.
The horn sound is weak.

2-6 Quick index

Push the defogger switch to change to the “ ” position.

Have the battery checked. Recharge or replace as needed.

P. 7-8

P. 8-2,

9-13

If this problem occurs...

2

Typ e 1

Typ e 2

and

Problem Do this Ref. Page

The information screen in the
multi information display will
be interrupted and the engine
coolant temperature warning

display will appear. Also “ ”
will blink. (Type 1: Color liquid
crystal display type)
The high coolant temperature
warning light will illuminate.
(Type 2: Mono-color liquid
crystal display type)

Steam comes out of the engine
compartment.

The engine is overheated.
Carefully stop the vehicle in a safe place.

P. 8 - 4

Quick index 2-7

If this problem occurs...

2

WAR N ING

Problem Do this Ref. Page

1. Slowly press down on the accelerator pedal to get your vehicle moving again. For an all­wheel drive vehicle, set the drive mode-selector to the “4WD AUTO” or “4WD LOCK”

If your vehicle becomes stuck in
sand, mud or snow

 When attempting to rock your vehicle out of a stuck position, be sure that no one is near the vehicle. The rocking motion may cause the vehicle to

suddenly lurch forward or backward, possibly injuring bystanders.

 Avoid revving the engine or spinning the wheels. Prolonged efforts to free a stuck vehicle may result in overheating and transaxle failure.

If the vehicle remains stuck after several rocking attempts, have a towing service pull the vehicle out.

Problem Do this Ref. Page

The brakes are not functioning
properly after crossing a puddle
or stream.

The automatic transaxle makes
no gear change when accelerat­ing. The initial movement of the
vehicle is slow when the vehicle
starts moving.
(for vehicles with automatic
transaxle)

position (Electronically controlled 4WD), “SNOW” or “LOCK” position (S-AWC) and
then slowly press down on the accelerator pedal to get your vehicle moving.

2. If there is nothing to stop your tires from slipping, rock your vehicle out of the stuck posi­tion.

Dry out the brakes by driving slowly while lightly pressing the brake pedal.

There may be a problem in the automatic transaxle.
Have the system inspected by your authorized Mitsubishi Motors dealer or a repair facility of
your choice.

P. 8-15

P. 5-90,

6-5

P. 5-74

2-8 Quick index

If this problem occurs...

2

Problem Do this Ref. Page

The continuously variable trans­mission (CVT) makes no shift
change when accelerating. The
initial movement of the vehicle
is slow when the vehicle starts
moving.
(for vehicles with CVT)

A tire is punctured.

There may be a problem in the CVT.

If the or warning lights on the multi-information display (Color liquid crystal display
type) will not turn off, or if they come on frequently, please have the vehicle checked at your
nearest Mitsubishi Motors dealer.

P. 5-81

1. Park the vehicle in a safe place where the surface is flat and level.

2. Replace the flat tire with the spare tire.

P. 8 - 6

Quick index 2-9

3

General information

Fuel selection ...................................................................................3-2

Filling the fuel tank ..........................................................................3-3

Modifications to and racing of your vehicle ....................................3-5

Genuine Mitsubishi Motors parts ....................................................3-7

California Perchlorate Materials Requirements ...............................3-7

Fuel selection

3

WAR N ING

CAUTION

Fuel selection

Your vehicle is designed to use unleaded gas­oline only. It is equipped with a fuel tank
filler pipe specifically designed to accept only
a small diameter unleaded gasoline dispens­ing nozzle.

 Gasoline is highly flammable and explo-

sive. You could be burned, seriously
injured or killed when handling it. When­ever you refuel your vehicle, stop the
engine and keep flames, sparks, and
smoking materials away from the vehicle.
Always handle fuel in well-ventilated out­door areas.

 Using leaded gasoline in your vehicle will

damage the engine, catalytic converter, and
the oxygen sensors. Also, using leaded gaso­line is illegal, and will void your warranty
coverage of the engine, catalytic converter,
and oxygen sensors.

Gasoline detergent additives

In the United States, fuel suppliers are
required by law to add detergents to their gas-

N00301001951

oline to minimize fuel-injector clogging and
minimize intake-valve deposits. Detergent
gasoline helps keep your engine in tune and
your emission-control system working prop­erly.

Octane requirement

2.4 liter engine model

Your vehicle is designed to operate on
unleaded gasoline having a minimum octane
number of 87 [(MON+RON)/2] or 91 RON.

3.0 liter engine model

Unleaded gasoline having a minimum octane
number of 87 [(MON+RON)/2] or 91 RON
may be used, though it is recommended your
vehicle be operated on premium grade
unleaded gasoline having a minimum octane
number of 91 [(MON+RON)/2], or 95 RON.
To obtain maximum performance, premium
gasoline is recommended.

Oxygenated gasoline

Gasoline sold at some service stations con­tains oxygenates such as ethanol, although

the oxygenates may not be identified by those
names. Oxygenates are required in some
areas of the country. Oxygenated fuel can be
used in your vehicle.

Ethanol (Gasohol)

A mixture of up to 10 % ethanol (grain alco­hol) and 90 % unleaded gasoline may be used
in your vehicle, provided the octane number
is at least as high as that recommended for
unleaded gasoline.

Methanol

Do not operate your vehicle on gasoline con­taining methanol (wood alcohol). Using this
type of alcohol could adversely affect the
vehicle’s performance and damage critical
parts of the vehicle’s fuel system.

Reformulated gasoline

Many areas of the country require the use of
cleaner burning fuel referred to as “Reformu­lated Gasoline”.
Reformulated gasoline contains oxygenates
and is specially blended to reduce vehicle
emissions and improve air quality.

3-2 General information

Filling the fuel tank

3

NOTE

WAR N ING

NOTE

Mitsubishi Motors Corporation strongly sup­ports the use of reformulated gasoline. Prop­erly blended reformulated gasoline has no
adverse effect on vehicle performance or the
durability of the engine and the fuel system.

MMT (methylcyclopentadienyl
manganese tricarbonyl)

MMT is a manganese-containing metallic
additive that is blended into some gasolines
to increase the octane number. Mitsubishi
Motors Corporation recommends using gaso­lines without MMT.
Use of gasolines blended with MMT may
adversely affect performance, and cause the
malfunction indicator on your instrument
panel to come on. If this happens, contact an
authorized Mitsubishi Motors dealer or a
repair facility of your choice for assistance.

Sulfur in gasoline

Your vehicle may have been designed to sat­isfy California’s low-emission regulations
based on clean-burning low-sulfur gasoline.
Gasoline sold in parts of the country other
than California is allowed to have a higher
sulfur content. Using such gasoline could
adversely affect the vehicle’s catalytic con­verter and cause the engine malfunction indi-

cator (“SERVICE ENGINE SOON” or
“Check engine light”) to come on. Illumina­tion of this indicator while using high-sulfur
gasoline does not necessarily mean the vehi­cle’s emission-control system is malfunction­ing. Your authorized Mitsubishi Motors
dealer may suggest using a different, lower­sulfur brand of unleaded gasoline to deter­mine if the problem is fuel-related.

 Poor-quality gasoline can cause problems

such as hard starting, stalling during idling,
abnormal engine noise, and poor accelera­tion. If you experience any of these prob­lems, try using a different brand of gasoline.
If the engine malfunction indicator (“SER­VICE ENGINE SOON” or “Check engine
light”) flashes, have the vehicle inspected as
soon as possible by the nearest authorized
Mitsubishi Motors dealer or a repair facility
of your choice.

 Repeatedly driving short distances at low

speeds can cause deposits to form in the fuel
system and engine, resulting in hard starting
and poor acceleration. If these problems
occur, you are advised to add a detergent
additive to the gasoline when you refuel the
vehicle. The additive will remove the depos­its, thereby returning the engine to a normal
condition. Be sure to use a Mitsubishi
Motors Genuine cleaning additive. Using an
unsuitable additive could make an engine
malfunction. For details, please contact the
nearest authorized Mitsubishi Motors dealer.

Filling the fuel tank

N00301101994

 When handling fuel, comply with the

safety regulations displayed by garages
and filling stations.

 Gasoline is highly flammable and explo-

sive. You could be burned, seriously
injured or killed when handling it. When
refueling your vehicle, always turn the
engine off and keep away from flames,
sparks, and smoking materials. Always
handle fuel in well-ventilated outdoor
areas.

General information 3-3

Filling the fuel tank

3

WAR N ING

WAR N ING

 Before removing the fuel tank filler cap,

be sure to get rid of your body’s static
electricity by touching a metal part of the
car or fuel pump. Any static electricity on
your body could create a spark that
ignites fuel vapor.

 Perform the whole refueling process

(opening the fuel tank filler door, remov­ing the fuel cap, etc.) by yourself; do not
let any other person near the fuel tank
filler. If you allowed a person to help you
and that person was carrying static elec­tricity, fuel vapor could be ignited.

 Do not move away from the fuel tank filler

until refueling is finished. If you moved
away and did something else (for example,
sitting on a seat) part-way through the
refueling process, you could pick up a
fresh charge of static electricity.

 Be careful not to inhale fuel vapor. Fuel

contains toxic substances.

 Keep the doors and windows closed while

refueling the vehicle. If they were open,
fuel vapor could get into the cabin.

Fuel tank capacity

Refueling

1. Before filling with fuel, stop the engine.

2. The fuel tank filler is located on the rear
driver side of your vehicle.
The fuel tank filler door can be opened
from inside the vehicle with the fuel tank
filler door release lever located at the left
side of the driver’s seat.

3. Open the fuel tank filler pipe by slowly
turning the fuel tank filler cap counter­clockwise.

1- Remove
2- Close

 Since the fuel system may be under pres-

sure, remove the fuel tank filler cap
slowly. This relieves any pressure or vac­uum that might have built up in the fuel
tank. If the cap is venting vapor or if you
hear a hissing sound, wait until the sound
stops before removing the cap. Otherwise,
fuel may spray out, injuring you or others.

All-wheel drive vehicles: 15.8 gal (60 L)
Front-wheel drive vehicles: 16.6 gal (63 L)

3-4 General information

Modifications to and racing of your vehicle

3

NOTE

CAUTION

CAUTION

WAR N ING

CAUTION

NOTE

5. When the nozzle stops automatically, do

 While filling with fuel, hang the fuel cap on

the hook (A) located on the inside surface of
the fuel tank filler door.

4. Fueling correctly depends mainly on cor­rect handling of the fuel filler nozzle. Do
not tilt the nozzle. Insert the nozzle in the
fuel tank filler port as far as it goes.

 Your vehicle can only be operated using

unleaded gasoline. Serious engine and cata­lytic converter damage will result if leaded
gasoline is filled into these vehicles, and
consequently, this must never be attempted.

not add more fuel.

 To avoid fuel spillage and overfilling, do not

“top-off” the fuel tank. Spilled fuel could
discolor, stain, or crack the vehicle’s paint­work. If fuel spills on the paintwork, wipe it
off with a soft cloth.

6. To re-install, turn the fuel tank filler pipe
cap slowly clockwise until you hear click­ing sounds, then gently push the fuel tank
filler door closed.

 Make sure the fuel tank filler cap is

securely closed. If the fuel cap were loose,
fuel could leak, resulting in a fire.

 If you need to replace the fuel tank filler cap,

use only the cap specified for your model
vehicle.

 If the fuel tank filler cap is not tight while

driving, the engine malfunction indicator
(“SERVICE ENGINE SOON” or “Check
engine light”) may come on when the
onboard diagnostic (OBD) system performs
a self check.
Always tighten the fuel tank filler cap until
you hear at least 3 clicks.
The indicator will go off after several driving
cycles. If the indicator does not go off, con­tact your authorized Mitsubishi Motors
dealer or a repair facility of your choice as
soon as possible.

Modifications to and racing
of your vehicle

N00301601205

This vehicle should not be modified with
non-Mitsubishi Motors genuine parts. Mit­subishi Motors designs and manufactures
high quality vehicles with an emphasis on
safety and durability. Modifications using
non-Mitsubishi Motors genuine parts may
affect the performance, safety and/or durabil­ity of your vehicle, and may violate applica­ble state and/or federal regulations.

DAMAGE OR PERFORMANCE PROB­LEMS RESULTING FROM MODIFICA­TIONS TO OR RACING OF YOUR

General information 3-5

Modifications to and racing of your vehicle

3

CAUTION

CAUTION

WAR N ING

VEHICLE ARE NOT COVERED
UNDER WARRANTY.

Examples of modifications to your vehicle
that can cause damage or performance prob­lems include the following:

 Failure to use Mitsubishi Motors genuine

parts

 Failure to use required fuel and fluids
 Failure to use proper size tires and wheels
 Modification of the fuel, intake, exhaust,

emission, suspension, engine, drive train
or electrical wiring systems

 Modification of any onboard com-

puter/control module, including repro­gramming, or replacing/adding chips to
any onboard computer/control module

Review the Warranty and Maintenance Man­ual for further details regarding warranty cov­erage.

Installation of accessories

 Before any electrical or electronic accesso-

ries are installed, consult an authorized Mit­subishi Motors dealer.

N00301701251

 Your vehicle is equipped with a diagnosis

connector (data link connector) for checking
and servicing the electronic control system.
Mitsubishi Motors does not recommend con­necting a device other than the Scan Tool for
inspections and service to this connector
because an unexpected problem could result.
In addition, malfunctions caused by connect­ing a device other than the Scan Tool may
not be covered under warranty.

 The installation of accessories, optional

parts, etc., should only be performed
within the limits prescribed by law, and in
accordance with the guidelines and warn­ings contained within the documents
accompanying this vehicle.
Only Mitsubishi Motors approved acces­sories should be fitted to your vehicle.

 Improper installation of electrical parts

could cause a fire. Refer to the “Modifica­tion/alterations to the electrical or fuel
systems” section within this owner’s man­ual.

 Using a cellular phone or radio set inside

the vehicle without an external antenna
may cause electrical system interference,
which could lead to unsafe vehicle opera­tion.

 Tires and wheels which do not meet spec-

ifications must not be used.

Refer to the “Specifications” section for
information regarding wheel and tire
sizes.

 While driving, do not use a cellular phone

in a way that hinders safe driving. Any­thing, including cellular phone usage, that
distracts you from the safe operation of
your vehicle increases your risk of an acci­dent.
Refer to and follow all state and local laws
in your area regarding cellular phone
usage while driving.

Important point!

Due to the large number of accessory and
replacement parts provided by different man­ufacturers in the market, it is not always pos­sible for an authorized Mitsubishi Motors
dealer to check whether the attachment or
installation of a non-Mitsubishi Motors genu­ine parts affects the driving safety of your
Mitsubishi-vehicle.

3-6 General information

3

CAUTION

Modification/alterations to the
electrical or fuel systems

N00301800141

Mitsubishi Motors manufactures high quality
vehicles with an emphasis on safety. It is
important to consult an authorized Mitsubishi
Motors dealer before installation of any
accessory which may involve modification of
the electrical or fuel systems.

 Please consult an authorized Mitsubishi

Motors dealer concerning any such acces­sory fitment or modification.
If the wires interfere with the vehicle body or
improper installation methods are used (pro­tective fuses not included, etc.), electronic
devices may be adversely affected, resulting
in a fire, vehicle damage, or other accident.

Genuine Mitsubishi Motors
parts

N00301400219

Mitsubishi Motors Genuine Parts are
designed and manufactured to meet high stan­dards of performance, and are recommended
for all of your maintenance needs. Also avail­able from your Mitsubishi Motors dealer are
a wide variety of accessories to personalize
your new vehicle. Each Mitsubishi Motors

Genuine Mitsubishi Motors parts

vehicle has a selection of Mitsubishi Motors
authorized accessories to choose from to tai­lor your new vehicle to your own personal
preference. Your Mitsubishi Motors dealer’s
Parts Manager has information on various
audio systems, protection items, as well as
interior and exterior accessories available for
your specific model.

California Perchlorate
Materials Requirements

N00300100017

Certain components of this vehicle, such as
airbag modules, seat belt pretensioners, and
button cell batteries, may contain perchlorate
materials.
Special handling may apply. For additional
information, see www.dtsc.ca.gov/hazardous­waste/perchlorate.

General information 3-7

4

Seat and restraint systems

Seats .................................................................................................4-2

Seat arrangement .............................................................................4-3

Seats and restraint systems ..............................................................4-4

Front seats ........................................................................................4-4

Second row seats ..............................................................................4-8

Third row seat (Seating 7 passengers) ...........................................4-10

Head restraints ...............................................................................4-11

Making a cargo area .......................................................................4-13

Making a flat seat ...........................................................................4-16

Seat belts ........................................................................................4-18

Seat belt use during pregnancy ......................................................4-25

Seat belt pre-tensioner and force limiter systems ..........................4-25

Child restraint systems ...................................................................4-27

Maintenance and inspection of seat belts ......................................4-34

Supplemental Restraint System (SRS) - airbag .............................4-35

4

Seats

Seats

N00408401607

1 - Front seat

 To adjust the seat forward or backward

 Page 4-5

 To adjust the seatback  Page 4-6
 To adjust the seat height (Driver’s seat

only)  Page 4-6

 Heated seat (if so equipped)  Page 4-8

2 - Second row seats

 To adjust the seat forward or backward

(vehicles with second row seat slide func­tion)  Page 4-8

4-2 Seat and restraint systems

 To adjust the seatback  Page 4-8
 Arm rest  Page 4-10
 Accessing the third row seat (Seating 7

passengers)  Page 4-10

3 - Third row seat (Seating 7
passengers)

 To adjust the seatback  Page 4-10

4

Seat arrangement

You may arrange your seats in the following positions.

Seat arrangement

N00401701122

Seating 5 passengers Seating 7 passengers

Ordinary use

Flat seatPage 4-16

Folding the second row
seats
Page 4-13

Making a cargo
area

Folding the third row
seatsPage 4-16

—

Seat and restraint systems 4-3

Seats and restraint systems

4

WAR N ING

WAR N ING

Manual seat adjustment Power seat adjustment

CAUTION

WAR N ING

Seats and restraint systems

Your vehicle has seat belts and other safety
features that help protect you and your pas­sengers in an accident.
Seat belts are the most important safety
device. When worn properly, seat belts can
reduce the chance of serious injury or death
in various types of crashes. For added protec­tion during a severe frontal collision, your
vehicle has a Supplemental Restraint System
(SRS) with airbags for the driver and passen­gers. The seats, head restraints, and door
locks also are safety equipment, which must
be used correctly.

Always check the following before you drive:

 That everyone in your vehicle is properly

wearing their seat belt.

 That infants and small children are prop-

erly secured in an appropriate child
restraint system in the rear seat.

 That all doors are fully closed and locked.
 That seatbacks are upright, with head

restraints properly adjusted.

Safety equipment cannot prevent injury or
death in all motor vehicle accidents. How­ever, you can help reduce the risk of injury or
death, by following the instructions in this
manual.

N00401601251

 Do not place objects under the seats. This

could prevent the seat from locking
securely, and it could lead to an accident.
It may also cause damage to the seat or
other parts.

Front seats

N00401801426

Position the driver’s seat as far back as possi­ble while maintaining a position that still
enables you to fully apply the pedals, easily
control the steering wheel and safely operate
the vehicle.

 Do not attempt to adjust the seat while

driving. This can cause loss of vehicle con­trol and result in an accident.

 After adjusting the seat, make sure that it

is securely locked into position.

 To reduce the risk to the driver of serious

injury or death during deployment of the
driver’s airbag, always properly wear the
seat belt and adjust the driver’s seat as far
back as possible while maintaining a posi­tion that still enables you to fully apply the
pedals, easily control the steering wheel,
and safely operate the vehicle.

 To reduce the risk to the front passenger

of serious injury or death during deploy­ment of the passenger’s airbag, always
properly wear the seat belt and adjust the
front passenger’s seat as far back as possi­ble.

 Always place children 12 years old and

under in the rear seat and use appropriate
child restraint systems.

 Make sure that the seat is adjusted by an

adult. If it is adjusted by a child, an unex­pected accident might occur.

 Do not place a cushion or the like between

your back and the seatback while driving.
The effectiveness of the head restraints will
be reduced in the event of an accident.

 When sliding the seats, be careful not to

catch your hand or leg.

4-4 Seat and restraint systems

Front seats

4

CAUTION

WAR N ING

NOTE

To adjust the seat forward or

 When sliding or reclining the seat rearward,

pay careful attention to the second row seat
passengers.

 When adjusting the front seat while the sec-

ond row seat is folded, be careful not to
apply strong force to the flipped second row
seat cushion.
Doing so could cause damage to the cover of
the front seat and the fitting of the second
row seat cushion.

backward

N00401901326

Manual seat adjustment

Pull the seat adjusting lever up and slide the
seat forward or backward to the desired posi­tion. Release the adjusting lever to lock the
seat in place.

 To make sure that the seat is securely

locked, try to move it forward or back­ward without using the adjusting lever.

Power seat adjustment

Operate the switch forward or backward to
move the seat to the desired position. Release
the switch to lock the seat in place.

1- Forward (toward the front of the vehicle)
2- Backward (toward the rear of the vehi-

cle)

 To prevent the battery from completely dis-

charging, operate the power seat with the
engine running.

Seat and restraint systems 4-5

Front seats

4

CAUTION

NOTE

WAR N ING

To adjust the seatbacks

Manual seat adjustment

To adjust the seatback, lean forward slightly,
gently pull the seatback lock lever up, then
lean backward to a comfortable position and
release the lever. The seatback will lock in
place.

 The reclining mechanism used in the seat-

back is spring loaded, and will cause the
seatback to return quickly to the vertical
position when the lock lever is operated.
When pulling the lever, sit close to the seat­back or hold the seatback with your hand to
control its return motion.

N00402001379

Power seat adjustment

Operate the switch in the direction of the
arrows to adjust the seatback.

1- Move forward
2- Move backward

 To prevent the battery from completely dis-

charging, operate the power seat with the
engine running.

 To reduce the risk of serious injury or

death in the event of an accident or sud­den stop, all seatbacks should be kept in
the upright position while the vehicle is in
motion.
Seat belt performance during an accident
can be adversely affected if the seatbacks
are reclined. The more a seatback is
reclined, the more likely seat belt perfor­mance will be adversely affected. If the
seat belt is not properly positioned against
the body during an accident, there is
increased risk you will slide under the belt
and receive serious injury or death.

To adjust the seat height
(Driver’s seat only)

N00402101253

Manual seat adjustment

Operate the lever repeatedly to raise or lower
the seat.

4-6 Seat and restraint systems

Front seats

4

NOTE

1- Raise
2- Lower

Power seat adjustment

Operate the switch in the direction of the
arrows to raise or lower the seat.

 To prevent the battery from completely dis-

charging, operate the power seat with the
engine running.

1- Raise or lower the front end of the seat

2- Raise or lower the back end of the seat

3- Raise or lower the entire seat

Seat and restraint systems 4-7

Second row seats

4

Type 1

Type 2

WAR N ING

CAUTION

CAUTION

Heated seat (if so equipped)

The heated seats can be operated by pushing
the switch when the ignition switch or the
operation mode is in ON. The indicator light
(A) will illuminate while the heater is on.

1 (HI) - Heater high (for quick heat-

ing)
2 (neutral
position)

- Heater off

N00435601463

3 (LO) - Heater low (to keep the seat

warm)

 Persons who are unable to feel tempera-

ture change or skin pain due to age, ill­ness, injury, medication, alcohol use,
fatigue or other physical conditions or
who have sensitive skin may suffer burns
when using the heated seat even at low
temperatures. To reduce the risk of burns,
people with such conditions must use care
when using the heated seat.

 Switch off the heated seats when not in use.

Operate the heaters at the “HI” position for
quick heating. After the seat has become
warm, set the heater switch to the “LO” posi­tion to keep it warm. Slight variations in the
seat temperature may be felt while using the
heated seats. This is caused by the operation
of the heater’s internal thermostat and does
not indicate a malfunction.

 Do not place heavy objects on the seat or

stick pins, needles, or other pointed objects
into the seat.

 Do not place a blanket, cushion, or other

insulating material on the seat while using
the heater; doing so can cause the heater ele­ment to overheat.

 When cleaning the seat, do not use benzine,

kerosene, gasoline, alcohol, or other organic
solvents; doing so can cause damage not
only to the surface of the seat, but also to the
heater.

 If water or any other liquid is spilled on the

seat, allow it to dry thoroughly before
attempting to use the heater. Turn the heater
off immediately if it appears to be malfunc­tioning during use.

Second row seats

N00402501231

When sitting in the middle seating position of
the second row seat, adjust the head restraints
to an appropriate height where they lock in
position. Refer to “Head restraints” on page
4-11.

To adjust the seat forward or
backward (vehicles with sec­ond row seat slide function)

Pull the seat adjusting lever up and slide the
seat forward or backward to the desired posi­tion. Release the adjusting lever to lock the
seat in place.

4-8 Seat and restraint systems

Second row seats

4

NOTE

WAR N ING

CAUTION

NOTE

WAR N ING

WAR N ING

To adjust the seatbacks

 Seat belt performance during an accident

Pull the lever up and adjust the seatback by
hand to the desired position, and release the
lever. The seatback will lock in place.

 You can adjust the seat forward or backward

on either side separately.

 To make sure that the seat is securely

locked, try to move it forward or back­ward without using the adjusting lever.

 You can adjust the seatback forward or back-

ward on either side separately.

can be adversely affected if the seatbacks
are reclined. The more a seatback is
reclined, the more likely seat belt perfor­mance will be adversely affected. If the
seat belt is not properly positioned against
the body during an accident, there is
increased risk you will slide under the belt
and receive serious injury or death.

 When a person is sitting in the middle

seating position of the second row seats,
the two sides of the second seats must have
the same forward/backward position
(vehicles with second row seat slide func­tion) and the same seatback angle.

 When sliding (vehicles with second row seat

slide function) or reclining the seat rearward,
pay careful attention to the third row seat
passengers.

 To reduce the risk of serious injury or

death in the event of an accident or sud­den stop, all seatbacks should be kept in
the upright position while the vehicle is in
motion.

Seat and restraint systems 4-9

Third row seat (Seating 7 passengers)

4

NOTE

WAR N ING

WAR N ING

Arm rest

To use the armrest, tilt the arm rest down for
use as shown.
The arm rest includes a cup holder.

 Never sit on an arm rest.

Doing so could damage the arm rest.

Accessing the third row seat
(Walk-in function, Seating 7
passengers)

For third row seat passenger entry or exit, the
second row seats can be moved forward.
Pull up the lever (A) and tilt the seatback for­ward. Then slide the entire seat forward.

N00403001318

N00400101031

To return the seat, slide the entire seat back­ward to the desired position and then raise the
seatback until it locks securely.
After returning the seat, gently try to move it
forward and backward to check that it is
securely retained and adjust the seatback to
the normal seating position.

 To make sure that the seat is securely

locked, try to move it forward or back­ward without using the lever. To reduce
the risk of serious injury or death in the
event of an accident or sudden stop, all
seatbacks should be kept in the upright
position while the vehicle is in motion.

Third row seat (Seating 7
passengers)

N00419501073

 The third row seats are intended for use

by no more than two belted occupants,
each of which does not exceed 160 cm (63
inches) in height.
Exceeding these limitations can result in
an increased risk of personal injury or
death in the event of an accident.

To adjust the seatback

Pull up the strap and adjust the seatback by
hand to the desired position, and release the
strap.

4-10 Seat and restraint systems

Head restraints

4

WAR N ING

NOTE

WAR N ING

Head restraints

N00404301594

Head restraints can reduce the risk of a whip­lash injury if your vehicle is hit from the rear.
The head restraints are equipped in the illus­trated position.
To maximize the effectiveness of the head
restraints, adjust the seatback to the upright
position, and the head restraint to the proper
position. Sit back against the seatback with
your head close to the head restraint.

 Driving without the head restraints in

place can cause you and your passengers
serious injury or death in an accident. To
reduce the risk of injury in an accident,
always make sure the head restraints are
installed and properly positioned when
the seat is occupied.

 In order to minimize the risk of a neck

injury due to a rear impact, the seatback
must be adjusted to the upright position
and the head restraint must be adjusted to
the proper position before vehicle opera­tion. The driver should never adjust the
seat while the vehicle is in motion.

 Never place a cushion or similar device on

the seatback. This can adversely affect
head restraint performance by increasing
the distance between your head and the
restraint.

*: Seating 7 passengers

 When a person sits in the second center

seating position, pull up the head restraint
to a height at which it locks in position. Be
sure to make this adjustment before start­ing to drive. Serious injuries could other­wise be suffered in the result of an impact.

 The head restraint height in the second row

outboard seats and the third row seats cannot
be adjusted.

Seat and restraint systems 4-11

Head restraints

4

WAR N ING

CAUTION

CAUTION

Adjustment of the head
restraint height (front seats)

To reduce the risk of injury in an accident,
adjust the head restraint height so that the
center of the restraint is at your ear level
when seated. Any person too tall for the
restraint to reach their ear level when seated
should raise the restraint to the highest locked
position.

 To raise the restraint, pull it straight up.
 To lower the restraint, push down on it

while pressing the lock knob (A) in the
direction shown by the arrow.

 After adjusting the height, push down on

the restraint to make sure it is locked in
position.

To remove

Press the lock knob (A) in the direction
shown by the arrows. Then pull the head
restraint up and out of the seatback.

 To help minimize the risk of neck injury in

the event of an accident, the head
restraints must be properly installed and
positioned to proper height before vehicle
operation.

To install

pressing the lock knob (A) until the restraint
locks into place.

 Check that the lock knob (A) is extended out

as shown in the illustration. Then pull the
head restraint up to make sure that it is
locked in place and will not come out of the
seatback.

 The shape and size of the head restraint dif-

fers according to the seat. Always use the
correct head restraint provided for the seat
and do not install the head restraint in the
wrong direction.

4-12 Seat and restraint systems

First check that the head restraint is facing in
the right direction as shown in the previous
illustration, and then insert it into the seat­back. Push the head restraint down while

Making a cargo area

4

WAR N ING

CAUTION

NOTE

WAR N ING

NOTE

 When driving the vehicle, do not allow

anyone to sit on the third row seat if the
second row seat is in the folded position.

 You can separately fold the right and left side

of the second row seat.

To fold the second row seat

 In the cargo area, do not load the luggage

higher than the top of the seats and make

Making a cargo area

N00405501115

 Never adjust the seats to make a cargo

area when the vehicle is in motion or on a
slope. The seats could move more than
necessary or move suddenly and causing a
serious accident and/or injury.

 When returning a seat back to its seating

position after folding down, make sure
that the seat is firmly secured and seat belt
buckles are in proper position. If the seat
is not secured, it could move causing a
serious accident.

 Do not allow anyone to ride in the cargo

area while the vehicle is in motion. People
who are not properly seated and
restrained can be seriously injured or
killed in an accident.

sure that the luggage is firmly secured.
Restricted rear vision or flying objects enter­ing the passenger compartment during sud­den braking could result in a serious accident
and/or injury.

 Seats should always be operated by an adult.

Seat adjustments by a child could lead to an
unexpected accident.

 When adjusting the seats, be careful not to

catch your hand or leg. Personal injury could
result.

 When the seatback of a front seat is reclined,

return it to the upright position before driv­ing.

Folding the second row seats

N00405701146

The second row seat can be folded to create
an additional cargo area.

1. When folding the left side second row
seat, store the seat belt for the middle
seating position of the second row seat.
Refer to “Detachable center seat belt for
second row” on page 4-21.

2. Lower the head restraint for second row
middle seating position to its lowest posi­tion.
Refer to “Head restraints” on page 4-11.

3. Pull the strap (A), then fold forward the
head restraints for second row outside
seating position.

Seat and restraint systems 4-13

Making a cargo area

4

NOTE

CAUTION

CAUTION

NOTE

4. On vehicles with the second row seat slide
function, move the second row seat fully
backward.
Refer to “To adjust the seat forward or
backward” on page 4-8.

 If you do not move the second row seat fully

backward, you may not be able to fold the
second row seat.

5. Pull the strap (B), then flip the seat cush­ion forward.

6. Fold forward the seat belt buckle.

 Do not allow any person to get on the plastic

cover (C), and do not place luggage on it.
Doing so could damage the plastic cover.

7. Pull up the lever (D), then fold the seat­back forward.

 Do not allow any person to sit on the flipped

seat cushion, and do not place luggage on it.
The seat’s mounting fittings could bend
under the weight, making it impossible for
the seat cushion to be secured when it returns
to the original position.

 If the seatback cannot be folded, follow the

steps below.

1. Raise the seatback once until it locks.

2. Pull the strap again.

3. Pull up the lever, then fold the seatback
forward.

4-14 Seat and restraint systems

Making a cargo area

4

NOTE

WAR N ING

To re tu r n

1. Raise the seatback until it locks securely
into place.

2. While lifting the seat belt buckle (A), gen­tly lower the seat cushion. Make sure that
there is a hook (B) at the position shown
in the illustration.

 A rubber strap (C) is attached to the seat belt

buckle for the left outboard seating position.
This helps raise the seat belt buckle while the
seat cushion returns to the original position.

3. Push down the seat cushion until it locks
securely into place.

 Ensure that the head restraints are

returned to their original positions before
the seats are occupied. Failure to do so
could cause serious injury if involved in an
accident.

6. If the center seat belt is stored;

• Pull out the detachable anchor plate (D)
from the seatback.

• Pull the small latch plate (E) slowly and
insert it into the detachable anchor plate
until a click is heard.

• Make sure that the seat belt is not
twisted.
For details, refer to “Detachable center
seat belt for second row” on 4-21.

4. Make sure that all seat belt buckles are
properly positioned on the seat cushion.

5. Return the folded head restraint to its
original position.

Seat and restraint systems 4-15

Making a flat seat

4

WAR N ING

CAUTION

Folding the third row seats
(Seating 7 passengers)

To f o ld

1. Remove the head restraints from the third
row seats. (Refer to “Head restraints” on
page 4-11.)

2. Pull up the strap (A), then fold the seat­back forward.

3. Stow the removed head restraints in the
luggage floor box with their front faces
facing downward.

N00409800021

To re tu r n

1. Pull the strap (A), then raise the seatback
until it locks securely into place.
Push lightly on the seatback to confirm
that it has actually been secured.

2. Install the head restraints.

Making a flat seat

N00404801166

The entire interior of the vehicle may be used
for sleeping accommodations by removing
the head restraints and fully reclining all the
seats when the vehicle is stopped.

 Never drive with passengers or cargo on

the flat seat. This is extremely dangerous
and can cause severe or fatal injury or
death in an accident or if heavy braking is
required.

 Adjust the seats only when the vehicle is

stopped in a safe place.

 Seat should be adjusted only by adults to

avoid accidents.

 When sliding the seats, be careful not to

catch your hand or leg.

 Do not walk around on top of the seats after

they have been laid flat because the footing
is uneven. It is safest to move about on your
hands and knees.

 To ensure the seats are locked securely,

attempt to move them back and forth.

 Do not jump on or drop heavy objects on the

seatbacks.

4-16 Seat and restraint systems

Making a flat seat

4

CAUTION

 To raise the seatback of the front seat, firmly

place your hand on the seatback, pull the
seatback lock knob up, and raise the seatback
slowly. (Refer to “To adjust the seatback” on
page 4-6.) Do not let children adjust the seat­back.

1. Remove the head restraints from the front
seats and raise the arm rest on the second
row seats.
For vehicles with a cargo area cover,
remove the cover.
(Refer to “Head restraints” on page 4-11,
“Arm rest” on page 4-10 and “Cargo area
cover” on page 5-244.)

3. Slide the front seats fully forward, then
recline their seatbacks backward to
achieve a flat surface.
(Refer to “To adjust the seat forward or
backward” on page 4-5 and “To adjust the
seatback” on page 4-6.)

5. The flat seat configuration is now com­plete.
To return the seats to the normal position,
reverse the above procedure.

2. Slide the second row seats back as far as
possible (vehicles with second row seat
slide function).
(Refer to “To adjust the seat forward or
backward” on page 4-8.)

4. Recline the seatbacks of the second row
seats.
(Refer to “To adjust the seatback” on page
4-8.)

Seat and restraint systems 4-17

Seat belts

4

WAR N ING

WAR N ING

WAR N ING

Seat belts

Seat belts are installed in your vehicle to help
reduce the risk of injury to the driver and pas­senger in the event of an accident. Always
use the provided seat belts.
Carefully review the following information
for proper seat belt usage.

 To help reduce the risk of injury or death

in an accident, seat belts and child
restraint systems must always be used.
Refer to “Child restraint systems” on page
4-27 for additional information.

 Never use one seat belt for more than one

person.

 Never carry more people in your vehicle

than there are seat belts.

 Always adjust the seat belt for a snug fit.
 Always place the shoulder belt over your

shoulder and across your chest. Never put
it behind you or under your arm.

 Always wear the lap belt as low as possible

across your hips, not around your waist.

N00406001511

 Never insert any foreign object, such as a

piece of plastic, paper clip, button or coin,
into the seat belt buckle.

 Never modify or alter the seat belts in

your vehicle.

 To reduce the risk to the driver of serious

injury or death during deployment of the
driver’s airbag, always properly wear the
seat belt and adjust the driver’s seat as far
back as possible while maintaining a posi­tion that still enables you to fully apply the
pedals, easily control the steering wheel,
and safely operate the vehicle.

 To reduce the risk to a front seat passen-

ger of serious injury or death from a
deploying airbag, make sure the passenger
always wears the seat belt properly,
remains seated all the way back and
upright in their seat, and moves the seat as
far back as possible. Refer to “Supplemen­tal Restraint System (SRS) - airbag” on
page 4-35 for additional information.

 Never hold an infant or child in your arms

or on your lap when riding in this vehicle
even when you are wearing your seat belt.
Never place any part of the seat belt you
are wearing around an infant or child.
Failure to follow these simple instructions
creates a risk of serious injury or death to
your child in the event of an accident or
sudden stop.

 Children 12 years old and under should

always ride in the rear seat and be prop­erly restrained. This reduces their risk of
serious injury or death in an accident,
especially due to a deploying front passen­ger’s airbag. Refer to “Child restraint sys­tems” on page 4-27 for additional
information.

 Any child who is too small to properly

wear a seat belt must be properly
restrained in an appropriate child
restraint system.

 Infants MUST be placed in a rear-facing

child safety seat and positioned in the rear
seat.

 In the event of an accident, all seat belt

assemblies, including retractors and
attachment hardware, should be inspected
by an authorized Mitsubishi Motors
dealer to determine whether replacement
is necessary.

4-18 Seat and restraint systems

Seat belts

4

NOTE

WAR N ING

Seat belt instructions

N00406201513

All seats are equipped with a seat belt which
uses one combined lap-and-shoulder belt with
an emergency locking retractor.

This system is designed to provide both com­fort and safety. It permits full extension and
automatic retraction of the belts during nor­mal vehicle operation. A sensing device
inside the belt retractor is designed to lock the
retractor in the event of a sudden change in
the vehicle’s motion.

1. Occupants should always sit back in their
seats with their backs against the upright
seatback. To reduce the risk of serious
injury or death during deployment of the
airbag, adjust the driver’s seat as far back
as possible while maintaining a position
that still enables you to fully apply the
pedals, easily control the steering wheel,
and safely operate the vehicle. The front
passenger seat should also be moved as
far back as possible. Refer to “Supple­mental Restraint System (SRS) - airbag”
on page 4-35. Also refer to “To adjust the
seat forward or backward” on page 4-5.

 To reduce the risk of serious injury or

death in the event of an accident or sud­den stop, all seatbacks should be kept in
the upright position while the vehicle is in
motion.

Seat belt performance during an accident
can be adversely affected if the seatbacks
are reclined. The more a seatback is
reclined, the more likely seat belt perfor­mance will be adversely affected. If the
seat belt is not properly positioned against
the body during an accident, there is
increased risk you will slide under the belt
and receive serious injury or death.

 For instructions on installing a child restraint

system using a seat belt, refer to “Installing a
child restraint system using the seat belt” on
page 4-32.

2. Before using the center seat belt for sec­ond row, make sure that the detachable
anchor is securely latched and the seat
belt is not twisted. For details, refer to
page 4-21.

Seat and restraint systems 4-19

Seat belts

4

NOTE

NOTE

WAR N ING

3. Grasp the latch plate and slide it up the
webbing so that it easily pulls across your
body.

4. Pull the seat belt out slowly while holding
the latch plate. Push the latch plate into
the buckle until you hear a “click”. Pull
up on the belt to be sure the latch plate is
locked securely in the buckle.

 If the seat belt locks up and cannot be pulled

out, pull it once with force and let it retract
all the way.
Then, pull the belt out slowly once again.

5. The lap part of the belt must always be
worn low and snug across the hips. Pull
up on the shoulder portion of the belt to
take up any slack in the lap belt.

 With the exception of the seat belt for the

driver, the seat belts in all other seating posi­tions are equipped with an Automatic Lock­ing Retractor (ALR) function. If you pull the
seat belt fully out of the retractor, the retrac­tor will switch to its ALR child restraint
installation function (see page 4-32).
When the ALR function has been activated,
the seat belt will only retract. If this happens,
let the belt fully retract, then pull the seat
belt back out, repeating steps 1 through 4.

 Be sure the lap belt portion fits snugly and

is worn as low as possible across the hips,
not around the waist. Failure to follow this
instruction will increase the risk of serious
injury or death in the event of an accident.

 Be sure the seat belt webbing is not

twisted when worn. Twisted webbing may
adversely affect seat belt performance.

4-20 Seat and restraint systems

Seat belts

4

NOTE

WAR N ING

NOTE

6. To release the belt, press the button on the
buckle and allow the belt to retract.
If the belt does not retract smoothly, pull it
out and check for kinks or twists in the
webbing. Then make sure it remains
untwisted as it retracts.

 If the seat belt (A) or ring (B) becomes dirty,

the belt may not retract smoothly. If the seat
belt and ring are dirty, clean them with a
mild soap or detergent solution.

Detachable center seat belt for
second row

N00409900035

The center seat belt for the second row can be
detached to fold the left side second row seat.
This seat belt must be worn correctly as illus­trated.

To attach

1. Pull out the detachable anchor plate (C)
from the storage pocket on seat back
cushion.

2. Pull out the small latch plate (A) and then
pull out the latch plate (B) by tilting it as
shown in the illustration.

 Never detach the center seat belt except

when the left side seat back in the second
row is folded. Using the center seat belt
with the detachable anchor unlatched
increases the risk of serious injury or
death in an accident. Make sure the small
latch plate (A) is properly latched to the
detachable anchor before the center seat
belt is used.

 Pulling out the latch plate by force may dam-

age the headliner.

Seat and restraint systems 4-21

Seat belts

4

NOTE

NOTE

3. Pull the small latch plate (A) slowly and
insert it into the detachable anchor plate
until a click is heard. Make sure that the
seat belt is not twisted.

 If the seat belt locks up and cannot be pulled

out, pull it once with force and let it retract
all the way.
Then, pull the belt out slowly once again.

 The seat belt can be buckled up by inserting

the latch plate (B) into the buckle (D) like
other seat belts.

 If the seat belt switch to the ALR child

restraint installation function and cannot be
pulled out, detach the latch plate (B) and
move the second row seat fully backward.
Refer to “Installing a child restraint system
using the seat belt” on page 4-32.

To d e ta ch

1. While holding the seat belt, insert a metal
plate, such the latch plate of the seat belt
or a key, into the slit (E) on the detachable
anchor (C) and release the center seat belt
from the detachable anchor.

2. Retract the seat belt slowly by holding the
seat belt.

 If the seat belt is not held, the seat belt will

rapidly retract. This could cause damage to
the interior trim.

3. After the seat belt has retracted com­pletely, insert the latch plate (B) into the
upper slit (F), and then insert the small
latch plate (A) into the lower slit (G).

4. Store the detachable anchor in the storage
pocket on the seatback.

4-22 Seat and restraint systems

4

Type 1

Type 2

WAR N ING

NOTE

Driver’s seat belt
reminder/warning light and
display

N00418401394

warning light will come on and a tone will
sound for approximately 6 seconds to remind
you to fasten your seat belt.
If the vehicle is driven with the seat belt still
unfastened, the warning light will blink and
the tone will sound intermittently until the
seat belt is fastened. At the same time, “FAS­TEN SEAT BELT” is displayed on the infor­mation screen in the multi information
display (Type 1 only).

 In order to reduce the risk of serious

injury or death in an accident, always fas­ten your own seat belt. Do not allow any­one to ride in your vehicle unless he or she
is also seated and fastening a seat belt.
Children should additionally be restrained
in a secure child restraint system.

 If the seat belt subsequently remains unfas-

tened, the warning light and the tone will
issue further warnings each time the vehicle
starts moving from a stop.

Seat belts

Front passenger seat belt warn­ing light

N00418301247

The front passenger seat belt warning light is
located in the instrument panel.

When the ignition switch is turned to the
“ON” position or the operation mode is put in
ON, this indicator normally comes on and
goes off a few seconds later.
The light comes on when a person sits on the
front passenger seat but does not fasten the
seat belt. It goes off when the seat belt is sub­sequently fastened.

A tone and warning light are used to remind
the driver to fasten the seat belt.
If the ignition switch is turned to the “ON”
position or the operation mode is put in ON
without the driver’s seat belt being fastened, a

Seat and restraint systems 4-23

Seat belts

4

WAR N ING

Anchor down Anchor up

WAR N ING

 When a child booster seat is used on the

front passenger seat, the front passenger
seat belt warning light will not come on, if
the seat belt is not fastened when the
booster seat is used. Confirm that the
child is wearing the seat belt properly.

 Do not install any accessory or sticker that

makes the light difficult to see.

Adjustable seat belt shoulder
anchor (front seats)

The seat belt shoulder anchor height can be
adjusted. To move the anchor down, press the
lock knob (A) and slide the anchor down to
the desired position. To move the anchor up,
slide the anchor up to the desired position.

N00406301354

 Always adjust the shoulder belt anchor so

that the shoulder belt is positioned across
the center of your shoulder without touch­ing your neck. The shoulder belt should
not be able to fall off your shoulder. Fail­ure to follow this instruction can adversely
affect seat belt performance and increase
the risk of serious injury or death in the
event of an accident.

 Adjust the shoulder belt anchor only when

the vehicle is not in motion.

 Make sure the anchor is securely locked in

position after adjusting it.

Storing the second row (out­board seating positions) and
third row seat belts

N00406501112

When seat belts for the second row outboard
seating position and for the third row are not
used, the seat belts can be stored.

4-24 Seat and restraint systems

Seat belt use during pregnancy

4

WAR N ING

WAR N ING

Put the seat belt webbing in the back slot (A)
on the clip and insert the metal plate of the
latch plate into the front slot (B) as shown in
the illustration.

Seat belt extender

N00406701202

If your seat belt is not long enough, even
when fully extended, a seat belt extender
must be obtained. The extender may be used
for either of the front seats.

Seat belt use during preg­nancy

N00406800134

Seat belts work for everyone, including preg­nant women. Like all occupants, pregnant
women are more likely to be seriously injured
or killed in an accident if they do not wear
seat belts.

 To reduce the risk of serious injury or

death to pregnant women and unborn
children in an accident, pregnant women
should always wear a seat belt. The lap
portion of the seat belt should be worn
snug and low across the hips and below
the rounding. Consult your doctor if you
have any additional questions or concerns.

 The extender should only be used if the

existing belt is not long enough. Anyone
who can use the standard seat belt should
not use an extender. Unnecessary use of an
extender can adversely affect seat belt
performance in an accident.

 When not required, the extender must be

removed and stowed.

Seat belt pre-tensioner and
force limiter systems

N00417701710

The driver’s and front passenger’s seats each
have a seat belt equipped with a pre-tensioner
system and force limiter system.

Seat and restraint systems 4-25

Seat belt pre-tensioner and force limiter systems

4

WAR N ING

Pre-tensioner system

The driver and front passenger seat belts are
equipped with a seat belt pre-tensioner sys­tem. In a moderate-to-severe frontal or side
collision or when a rollover or overturning of
the vehicle is detected, the pre-tensioner sys­tem operates simultaneously with the deploy­ment of the front airbags, side airbags or
curtain airbags.
The seat belt pre-tensioners are located in the
driver’s and front passenger’s seat belt retrac­tors (A) and in the front passenger seat’s final
anchor (B). When activated, the pre-tension­ers quickly draw back seat belt webbing and
increase seat belt performance.

The seat belt pre-tensioner system includes
the following components:

1- SRS warning light
2- Front impact sensors
3- Seat belt pre-tensioner
4- Airbag control unit
5- Side impact sensors
6- Seat belt buckle switches

The airbag control unit monitors the readiness
of the electronic parts of the system whenever
the ignition switch or the operation mode is
under the following conditions. These include
all of the items listed above and all related
wiring.
[Except for vehicles equipped with the
F.A.S. T.- ke y]
The ignition switch is in the “ON” or
“START” position.
[Vehicles equipped with the F.A.S.T.-key]
The operation mode is in ON.

The seat belt pre-tensioners will operate
under the same conditions as the airbag con­trol unit.

When the seat belt pre-tensioners activate,
some smoke is released and a loud noise will
be heard. The smoke is not harmful, but care
should be taken not to intentionally inhale it,
as it may cause some temporary irritation to
people with respiratory problems.
Even in the event of a severe impact, the pre­tensioners will not operate if the seat belts are
not fastened. The seat belt pre-tensioners may
not activate in certain collisions, even though
the vehicle may appear to be severely dam­aged. Such non-activation does not mean that
something is wrong with the seat belt pre-ten­sioner system, but rather that the collision
forces were not severe enough to activate the
system.

 The seat belt pre-tensioner system is

designed to work only once. After the seat
belt pre-tensioners have been activated,
they will not work again. They must
promptly be replaced and the entire seat
belt pre-tensioner system inspected by an
authorized Mitsubishi Motors dealer.

4-26 Seat and restraint systems

4

SRS warning

WAR N ING

N00408701147

This warning light tells you if there is a prob­lem involving the SRS airbags and/or the seat
belt pre-tensioner system. Refer to “SRS
warning light/display” on page 4-41.

The child restraint system should be appropri­ate for your child’s weight and height, and
should properly fit your vehicle’s seat.
For detailed information, refer to the instruc­tion manual accompanying the child restraint
system.

Child restraint systems

 Children who weigh more than 40 pounds

(18 kg) or who are more than 40 inches
(100 cm) tall, regardless of age, should
use a suitable child seat or a booster seat
in the rear seat until the vehicle’s lap-and­shoulder belt fits them properly.

Force limiter system

N00408900126

In the event of an accident, the seat belt force
limiter system will help reduce the force
applied to the driver and front seat passenger.

Child restraint systems

N00407101740

When transporting infants or small children
in your vehicle, an appropriate child restraint
system must always be used. This is required
by law in the U.S. and Canada.
Child restraint systems specifically designed
for infants and small children are offered by
several manufacturers. Choose only a child
restraint system with a label certifying that it
complies with Federal Motor Vehicle Safety
Standard 213 (FMVSS 213) or Motor Vehicle
Restraint Systems and Booster Seats Safety
Regulations (RSSR). Look for the manufac­turer’s statement of compliance on the box
and child restraint system itself.

Guidelines for child restraint
system selection

All children should be properly restrained in
a restraint device that offers the maximum
protection for their size and age.
Be sure to check local, state, or provincial
requirements for child size and age that may
vary from the recommendations listed below.

 Children less than 1 year old and who

weigh 22 pounds (10 kg) or less MUST
ride in a rear-facing child safety seat that
MUST ONLY be used in the second row
seat.

 Children older than 1 year of age and who

weigh less than 40 pounds (18 kg) or who
are less than 40 inches (100 cm) tall must
be in a forward-facing restraint used only
in the rear seat.

 All children must be seated in the rear

seat, and properly restrained.
Accident statistics show that children of
all sizes and ages are safer when properly
restrained in the rear seat, rather than in
the front seat.

 Be sure to select a child restraint system

that is appropriate not only for the child’s
size and age but also for your vehicle.
Some child restraint systems may not fit
your vehicle properly.

Seat and restraint systems 4-27

Child restraint systems

4

WAR N ING

WAR N ING

WAR N ING

Airbag

 Any child who is too large to use a child

restraint system should ride in the rear
seat and wear the lap-and-shoulder belt
properly. The shoulder belt must be posi­tioned over the shoulder and across the
chest, not across their neck, and with the
lap belt positioned low on the child’s hips,
not across their stomach. If necessary, a
booster seat should be used to help achieve
a proper seat belt fit. Follow the booster
seat manufacturer’s instructions. Only use
a booster seat that is certified as comply­ing with Federal Motor Vehicle Safety
Standards or Motor Vehicle Restraint Sys­tems and Booster Seats Safety Regula­tions.

 Never hold an infant or child in your arms

or on your lap when riding in this vehicle,
even when you are wearing your seat belt.
Never place any part of the seat belt you
are wearing around an infant or child.
Failure to follow these simple instructions
creates a risk of serious injury or death to
your child in the event of an accident or
sudden stop.

 Your vehicle is also equipped with a front

passenger’s airbag.
Never put REAR-FACING CHILD
RESTRAINT SYSTEMS or INFANT
RESTRAINT SYSTEMS in the front pas­senger seat. This places the infant too
close to the passenger’s airbag. During
deployment of that airbag, the infant can
be seriously injured or killed. Rear-facing
child restraint systems or infant restraint
systems must only be used in the rear seat.

4-28 Seat and restraint systems

Child restraint systems

4

WAR N ING

WAR N ING

WAR N ING

NOTE

 FRONT-FACING CHILD RESTRAINT

SYSTEMS should be used in the rear seat
whenever possible. If one must be used in
the front passenger seat, move the seat to
the most rearward position and make sure
the child stays in the child restraint sys­tem, properly restrained. Failure to follow
these instructions could result in serious
injury or death to the child.

 It is important to use an approved rear-

facing infant restraint until the infant is
one year old (unless the infant outgrows
the seat sooner). This allows the infant’s
neck and spine to develop enough to sup­port the weight of their head in the event
of an accident.

 When installing a child restraint system,

follow the instructions provided by the
manufacturer and follow the directions in
this manual. Failure to do so can result in
serious injury or death to your child in an
accident or sudden stop.

 After installation, push and pull the child

restraint system back and forth, and side
to side, to see that it is firmly secured. If
the child restraint system is not installed
securely, it may cause injury to the child
or other occupants in the event of an acci­dent or sudden stop.

 When not in use, keep your child restraint

system secured with the seat belt, or
remove it from the vehicle, in order to pre­vent it from being thrown around inside
the vehicle during an accident.

 Before purchasing a child restraint system,

try installing it in the rear seat to ensure
proper fit. Due to the location of the seat belt
buckles and the shape of the seat cushion, it
may be difficult to securely install some
manufacturer’s child restraint systems.
If the child restraint system can be pulled
forward or to either side easily on the seat
cushion after the seat belt has been tightened,
choose another manufacturer’s child restraint
system.
Depending on the seating position in the
vehicle and the child restraint system that
you have, the child restraint system can be
attached using one of the following 2 meth­ods:

• Attach to the lower anchorage in the second
row seat ONLY if the child restraint system
is compatible with the LATCH system (See
page 4-30).

• Attach to the seat belt (See page 4-32).

Seat and restraint systems 4-29

Child restraint systems

4

NOTE

Installing a child restraint sys­tem using the LATCH (Lower
Anchors and Tethers for chil­dren) system

Lower anchor locations

The outboard seating positions in the second
row seat of your vehicle are equipped with
lower anchors for attaching child restraint
systems compatible with the LATCH system.

 The symbols on the seatback show the loca-

tion of the lower anchor points.

N00418801167

Tether anchor locations Examples of child restraint sys-

N00418901201

Your vehicle has 3 attachment points on the
backside of the second row seats. These are
for securing a child restraint system tether
strap to each of the 3 rear seating positions in
your vehicle.

tems compatible with the LATCH
system

N00419000198

A- Rear-facing child restraint system

B- Front-facing child restraint system
C- Child restraint system lower anchor

connectors

D- Tether strap

(These are only examples.)

Using the LATCH system

N00419101301

1. In order to securely fasten the tether strap,
remove the head restraint from the loca­tion where you wish to install the child
restraint system.

2. Open the gap a little between the seat
cushion (A) and the seatback (B) with
your hand to locate the lower anchors (C).

4-30 Seat and restraint systems

Child restraint systems

4

NOTE

WAR N ING

NOTE

WAR N ING

3. For easier access, the seatback may be

D- Connector
recline rearward.
Push the anchor connectors (D) on the

child restraint system into the lower
anchors (C) in accordance with the
instructions provided by the child restraint
system’s manufacturer.
After it is security fastened, adjust the
seatback to 4 steps forward from most
reclined position.

Remember, the lower anchors (C) pro-

 In order to secure a child restraint system

compatible with the LATCH system, use the
lower anchor points in the outboard positions
of the second row seat. It is not necessary to
use the vehicle’s seat belt. The vehicle’s seat
belt, however, MUST be used to secure a
child restraint system in the middle seating
position of the second row seat.

vided with your vehicle are designed to
secure suitable child restraint systems
compatible with the LATCH system in
the outboard positions of the second
row seats only. The anchor connectors
are NOT designed to secure a suitable
child restraint system in the middle
seating position of the second row seat.

 If there is any foreign material in or

around the lower anchors, remove it
before installing the child restraint sys­tem. Also, make sure the seat belt is away
from, not looped through or otherwise
interfering with, the child restraint sys­tem. If foreign matter is not removed
and/or the seat belt interferes with the
child restraint system, the child restraint
system will not be secured properly, could
detach and move forward in the event of
sudden braking or an accident, and could
result in injury to the child or other vehi­cle occupants.

 When the vehicle is moving, do not adjust

the seat where the child restraint system is
installed.

A- Vehicle seat cushion
B- Vehicle seatback
C- Lower anchor

4. Latch the tether strap hook (E) of the child
restraint system to the tether anchor bar
(F) and tighten the tether strap so it is
securely fastened.

 If it is difficult to latch the tether strap hook,

turn the hook sideways.

5. Push and pull the child restraint system in
all directions to ensure it is firmly
secured.

 Child restraint system tether anchors are

designed only to withstand loads from cor­rectly fitted child restraint systems. Under
no circumstances are they to be used for
adult seat belts, harnesses, for attaching
other items, or equipment to the vehicle.

Seat and restraint systems 4-31

Child restraint systems

4

WAR N ING

WAR N ING

WAR N ING

 When using a child restraint in a rear

seating position, always review the
instructions provided with that restraint
to make sure it is compatible with this
vehicle and to understand how to properly
install it.
Child restraints, including booster seats,
come in different sizes and configurations.
Depending on where you place these child
restraints, and depending on their size and
configuration, you may not be able to
access or properly use one or more adja­cent seat belt assemblies. If this occurs,
the adjacent seating position or positions
should not be used. Failure to use a seat
belt or improper use of a seat belt can
result in serious injury or death should a
crash occur.

Installing a child restraint sys­tem using the seat belt (with
emergency/automatic locking
mechanism)

With the exception of the driver, the seat belt
in all other seating positions can be converted
from normal Emergency Locking Retractor
(ELR) mode, to Automatic Locking Retractor
(ALR) mode. This means that when you pull
the seat belt fully out of the retractor, the
retractor will switch to its ALR child restraint

N00407301553

installation function. Always use the ALR
child restraint installation function when you
install a child restraint system using the seat
belt.
Children 12 years old and under should
always be restrained in the rear seat, when­ever possible, although the front passenger
seat belt can also be converted to ALR mode.

 When you install a child restraint system

using the seat belt, always make sure the
retractor has been switched to the ALR
child restraint installation function. The
ALR function will keep the child restraint
system tightly secured to the seat.
Failure to convert the retractor to the
ALR function may allow the child
restraint system to move forward during
sudden braking or an accident, resulting
in serious injury or death to the child or
other occupants.

 When using a child restraint in a rear

seating position, always review the
instructions provided with that restraint
to make sure it is compatible with this
vehicle and to understand how to properly
install it.
Child restraints, including booster seats,
come in different sizes and configurations.
Depending on where you place these child
restraints, and depending on their size and
configuration, you may not be able to
access or properly use one or more adja­cent seat belt assemblies. If this occurs,
the adjacent seating position or positions
should not be used. Failure to use a seat
belt or improper use of a seat belt can
result in serious injury or death should a
crash occur.

Installation

1. Place the child restraint system on the seat
where you wish to install it.
To help assure proper fitting of the child
restraint system, always remove the head
restraint.
When installing the front-facing child
restraint system on the second row seat,
adjust the angle of the second row seat­back to the most upright position.

4-32 Seat and restraint systems

Child restraint systems

4

2. Route the seat belt through the child
restraint system according to the instruc­tions provided by the child restraint sys­tem’s manufacturer. Then insert the seat
belt latch plate into the buckle. Make sure
you hear a “click” when you insert the
latch plate into the buckle.

3. To activate the ALR child restraint instal­lation function, slowly pull the shoulder
part of the belt all the way out of the
retractor until it stops. Then let the belt
feed back into the retractor.

4. After the belt has retracted, tug on it.
If the belt is in the ALR function, you will
not be able to pull it out. If the webbing
can be pulled out from retractor, the ALR
function has not been activated and you
will need to repeat steps 3 and 4.

5. After confirming that the belt is locked,
grab the shoulder part of the belt near the
buckle and pull up to remove any slack
from the lap part of the belt allowing the
slack to feed into the retractor. Remember,
if the lap belt portion is not tight, the child
restraint system will not be secure. It may
help to put your weight on the child
restraint system and/or push on its seat­back while pulling up on the belt (See
illustration).

If your child restraint system requires the use
of a tether strap, fasten the tether strap in
accordance with the following procedures.

Seat and restraint systems 4-33

Maintenance and inspection of seat belts

4

NOTE

WAR N ING

WAR N ING

6. Latch the tether strap hook (A) of the
child restraint system to the tether anchor
bar (B) and tighten the tether strap so it is
securely fastened.

 If it is difficult to latch the tether strap hook,

turn the hook sideways.

 Child restraint system tether anchors are

designed only to withstand loads from cor­rectly fitted child restraint systems. Under
no circumstances are they to be used for
adult seat belts, harnesses, for attaching
other items, or equipment to the vehicle.

7. Before putting your child in the restraint,
push and pull the restraint in all directions
to be sure it is firmly secure. Do this
before each use. If the child restraint sys­tem is not firmly secure, repeat steps 1
through 6.

8. To remove a child restraint system from
the vehicle and deactivate the ALR mode,
remove the child from the restraint.
Unlatch the buckle. Then remove the belt
from the restraint and let the belt fully
retract.

9. Reinstall the head restraint.
Refer to “Head restraints” on page 4-11.

Children who have outgrown
child restraint systems

N00407601628

Children who have outgrown a child restraint
system should be seated in the rear seat and
wear the seat belt. If the shoulder belt crosses
their face or neck, and/or the lap belt crosses
their stomach, a commercially available
booster seat must be used to raise the child so
that the shoulder belt crosses their shoulder
and the lap belt remains positioned low
across their hips. The booster seat should fit
the vehicle seat and have a label certifying
compliance with Federal Motor Vehicle
Safety Standards or Motor Vehicle Restraint

Systems and Booster Seats Safety Regula­tions.

 Any child who is too small to properly

wear a seat belt must be properly
restrained in an appropriate child
restraint system, to reduce their risk of
serious injury or death in an accident.

 A child should never be left unattended in,

or unsupervised around, your vehicle.
When you leave the vehicle, always take
the child out as well.

 Children can die from heat stroke if left or

trapped inside the vehicle, especially on
hot days.

 Keep your vehicle locked when not in use.

Keep your vehicle keys away from chil­dren.

Maintenance and inspection
of seat belts

N00407001390

Regularly check your seat belt buckles and
their release mechanisms for positive engage­ment and release of the latch plate. Check the
retractors for automatic locking when in the
Automatic Locking Retractor function.

The entire seat belt assembly should be
replaced if the webbing shows any obvious

4-34 Seat and restraint systems

Supplemental Restraint System (SRS) - airbag

4

WAR N ING

cuts, tears, increase in thickness in any sec­tion of the webbing from broken fibers, or
severe fading from sunlight. All of these con­ditions indicate a weakening of the belt,
which may adversely affect seat belt perfor­mance in an accident.

Supplemental Restraint Sys­tem (SRS) - airbag

N00407701889

This vehicle is equipped with a Supplemental
Restraint System (SRS), which includes air­bags for the driver and passengers.

 Do not attempt to repair or replace any

part of the seat belt assemblies. This work
should be done by an authorized
Mitsubishi Motors dealer. Failure to have
an authorized Mitsubishi Motors dealer
perform the work could reduce the effec­tiveness of the belts and could result in a
serious injury or death in an accident.

 Never use an organic solvent to clean the

seat belt webbing. Do not attempt to
bleach or re-dye the seat belt webbing.
These may weaken the seat belt webbing,
increasing risk of injury or death in an
accident.
Clean seat belt webbing only with mild
soap or detergent solution and rinse it
with lukewarm water, and dry the seat
belt webbing completely before retracting
it.

The SRS front airbags are designed to supple­ment the primary protection of the driver and
front passenger seat belt systems by provid­ing those occupants with protection against
head and chest injuries in certain moderate to
severe frontal collisions. The SRS front air­bags, together with sensors at the front of the
vehicle and sensors attached to the front
seats, form an advanced airbag system.

The SRS driver’s knee airbag is designed to
supplement the primary protection of the
driver’s seat belt system. It can reduce the
forward movement of the driver’s lower legs
and provide increased overall body protection
in certain moderate to severe frontal colli­sions.

The SRS side airbags and the curtain airbags
are also designed to supplement the seat belts.
The SRS side airbags provide the driver and
front passenger with protection against chest
injuries by deploying the bag on the side
impacted in moderate to severe side impact
collisions. The SRS curtain airbags provide

the driver and the passengers on the front seat
and the second row outboard seats with pro­tection against head injuries by deploying the
curtain airbag on the side impacted in moder­ate to severe side impact collisions and by
deploying both curtain airbags when a roll­over is detected. The curtain airbags are also
designed to help reduce the risk of complete
and partial ejection from the vehicle through
side windows in both side impact and roll­over type accidents.

The SRS airbags are NOT a substitute for use
of the seat belts. For maximum protection in
all types of accidents, seat belts must
ALWAYS be worn by everyone who drives or
rides in this vehicle (with infants and small
children in an appropriate child restraint sys­tem in the rear seat, and older children buck­led in the rear seat). Refer to “Child restraint
systems” on page 4-27.

Seat and restraint systems 4-35

Supplemental Restraint System (SRS) - airbag

4

WAR N ING

WAR N ING

WAR N ING

 IT IS VERY IMPORTANT TO ALWAYS

WEAR YOUR SEAT BELT PROPERLY
EVEN WITH AN AIRBAG.

• Seat belts help keep the driver and pas­sengers properly positioned. This
reduces the risk of injury in all collisions,
and reduces the risk of serious injuries or
death when the airbags inflate.
During sudden braking just before a col­lision, an unrestrained or improperly
restrained driver or front passenger can
move forward into direct contact with, or
within close proximity to, the airbag
when it begins to inflate.
The beginning stage of airbag inflation is
the most forceful and can cause serious
injuries or death if the occupant comes in
contact with the airbag at this time.

• Seat belts reduce the risk of injury in
rear impact collisions, and in lower­speed frontal collisions because the air­bags are not designed to inflate in those
situations.

• Seat belts reduce the risk of being
thrown from your vehicle in a collision or
rollover.

 IT IS VERY IMPORTANT TO BE PROP-

ERLY SEATED.

• A driver or front passenger sitting too
close to the steering wheel or instrument
panel during airbag deployment can be
seriously injured or killed.

• Airbags inflate very quickly and with
great force. If the driver and front pas­senger are not properly seated and
restrained, the airbag may not provide
the proper protection, and can cause
serious injuries or death when it inflates.

• To reduce the risk to the driver of serious
injury or death due to a deploying
driver’s airbag, always properly wear
your seat belt and adjust the driver’s seat
as far back as possible, maintaining a
position that still allows the driver to
have good control of the steering wheel,
brake, accelerator, and other vehicle con­trols.

• To reduce the risk to the front passenger
of serious injury or death from a deploy­ing passenger’s airbag, make sure the
passenger always wears the seat belt
properly, remains seated upright and all
the way back in the seat, and positions
the seat as far back as possible.

• Seat all infants and children in the rear
seat, properly restrained in an appropri­ate child restraint system.

 Airbags inflate very quickly and with

great force. Do not sit on the edge of the
seat or sit with your lower legs too close to
the instrument panel, or lean your head or
chest close to the steering wheel or the
instrument panel.

 Do not put your feet or legs on or against

the instrument panel.

4-36 Seat and restraint systems

Supplemental Restraint System (SRS) - airbag

4

WAR N ING

WAR N ING

Airbag

WAR N ING

WAR N ING

 Infants and small children should never

ride unrestrained, or lean against the
instrument panel. They should never ride
held in your arms or on your lap. They
can be seriously injured or killed in an
accident, especially when the airbags
inflate. Seat all infants and children in the
rear seat, properly restrained in an appro­priate child restraint system. Refer to
“Child restraint systems” on page 4-27.

 NEVER put REAR-FACING CHILD

RESTRAINT SYSTEMS or INFANT
RESTRAINT SYSTEMS in the front pas­senger seat. This places the infant too
close to the passenger’s airbag. During
deployment of that airbag, the infant can
be seriously injured or killed.
Rear-facing child restraint systems or
infant restraint systems must only be used
in the rear seat.

 FRONT-FACING CHILD RESTRAINT

SYSTEMS should be used in the rear seat
whenever possible. If they must be used in
the front passenger seat, move the seat to
the most rearward position and make sure
the child stays in the child restraint sys­tem, properly restrained. Failure to follow
these instructions could result in serious
injury or death to the child.

 Older children should be seated in the

rear seat with their seat belt properly
worn, and with an appropriate booster
seat if needed.
Refer to “Children who have outgrown
child restraint systems” on page 4-34.

Seat and restraint systems 4-37

Supplemental Restraint System (SRS) - airbag

4

CAUTION

How the Supplemental
Restraint System works

N00407801532

The SRS includes the following components:

1- Airbag module (Driver)
2- SRS warning light
3- Passenger’s airbag off indicator
4- Front impact sensors
5- Airbag module (Passenger)
6- Airbag module (Driver’s knee)
7- Driver’s seat position sensor
8- Passenger’s seat occupant classifica-

tion sensor system

9- Airbag control unit

10- Side airbag modules
11- Curtain airbag modules
12- Side impact sensors

The airbag control unit monitors the readiness
of the electronic parts of the system whenever
the ignition switch or the operation mode is
under the following conditions. These include
all of the items listed above and all related
wiring.
[Except for vehicles equipped with the
F.A.S. T.- ke y]
The ignition switch is in the “ON” or
“START” position.
[Vehicles equipped with the F.A.S.T.-key]
The operation mode is in ON.

When the impact sensors detect a sufficient
front or side impact to deploy the airbag(s),
the appropriate airbag(s) will be deployed.

When the airbag control unit detects rollover
of the vehicle, curtain airbags will be
deployed.

When airbags deploy, some smoke is released
accompanied by a loud noise. The smoke is
not harmful, but do not intentionally inhale
the smoke as it may cause temporary irrita­tion to people with respiratory problems.

An inflated airbag will deflate quickly, so you
may not even notice that the airbag was
inflated.
Airbag inflation does not prevent the driver
from seeing or being able to steer the vehicle,
and does not prevent people from leaving the
vehicle.

 Airbags inflate very quickly and with great

force. In certain situations, contact with an
inflating airbag may cause small cuts, abra­sions, and bruises.

4-38 Seat and restraint systems

The airbags will operate under the same con­ditions as the airbag control unit.

Event Data Recording

N00418601266

This vehicle is equipped with an event data
recorder (EDR).

Supplemental Restraint System (SRS) - airbag

4

NOTE

WAR N ING

The main purpose of an EDR is to record, in
certain crash or near crash-like situations,
such as an airbag deployment or hitting a
road obstacle, data that will assist in under­standing how a vehicle’s systems performed.
The EDR is designed to record data related to
vehicle dynamics and safety systems for a
short period of time, typically 30 seconds or
less.

The EDR in this vehicle is designed to record

 EDR data are recorded by your vehicle only

if a non-trivial crash situation occurs; no data
are recorded by the EDR under normal driv­ing conditions and no personal data (e.g.,
name, gender, age, and crash location) are
recorded. However, other parties, such as
law enforcement, could combine the EDR
data with the type of personally identifying
data routinely acquired during a crash inves­tigation.

such data as:

 How various systems in your vehicle were

operating;

 Whether or not the driver and front pas-

senger safety belts were buckled/fastened;

 How far (if at all) the driver was depress-

ing the accelerator and/or brake pedal;
and,

To read data recorded by an EDR, special
equipment is required, and access to the vehi­cle or the EDR is needed. In addition to the
vehicle manufacturer, other parties, such as
law enforcement, that have the special equip­ment, can read the information if they have
access to the vehicle or the EDR.

 How fast the vehicle was traveling.

These data can help provide a better under­standing of the circumstances in which
crashes and injuries occur.

Driver’s seat position sensor

N00417900177

The driver’s seat position sensor is attached
to the seat rail and provides the airbag control
unit with information on the seat’s fore-aft
position. The airbag control unit controls
deployment of the driver’s front airbag in
accordance with the information it receives
from this sensor.
If there is a problem involving the driver’s
seat position sensor, the SRS warning light in

the instrument panel will come on. Refer to
“SRS warning light/display” on page 4-41.

 If the SRS warning light or warning dis-

play comes on, have the vehicle inspected
by an authorized Mitsubishi Motors
dealer as soon as possible.

 Please observe the following instructions

to ensure that the driver’s seat position
sensor can operate correctly.

• Adjust the seat to the correct position,
and sit well back against the seatback.
Refer to “Front seats” on page 4-4.

• Do not recline the seatback more than
necessary when driving.

• Do not place metallic objects or luggage
under the front seat.

 If the vehicle is involved in a severe

impact, have the SRS sensors inspected by
an authorized Mitsubishi Motors dealer as
soon as possible.

Passenger’s seat occupant clas­sification sensor system

N00418001374

The passenger’s seat occupant classification
sensor system is attached to the front passen­ger seat cushion and provides the airbag con­trol unit with information regarding the
occupant on the front passenger seat. The air-

Seat and restraint systems 4-39

Supplemental Restraint System (SRS) - airbag

4

WAR N ING

WAR N ING

WAR N ING

bag control unit controls deployment of the
passenger’s front airbag in accordance with
the information it receives from this system.
The passenger’s front airbag will not deploy
in an impact when the system senses no occu­pant on the front passenger’s seat or a child in
a child restraint system. In this case, the pas­senger airbag off indicator will come on.
Refer to “Passenger’s airbag off indicator” on
page 4-40.
If there is a problem involving the passen­ger’s seat occupant classification sensor sys­tem, the SRS warning light in the instrument
panel will come on. Refer to “SRS warning
light/display” on page 4-41.

 If any of the following conditions occur,

you should immediately have your vehicle
inspected by an authorized Mitsubishi
Motors dealer as soon as possible:

• The SRS warning light does not initially
come on when the ignition switch or the
operation mode is under the following
conditions.
[Except for vehicles equipped with the
F.A .S.T .- ke y]
The ignition switch is in the “ON” or
“START” position.
[Vehicles equipped with the F.A.S.T.-key]
The operation mode is in ON.

• The SRS warning light does not go out
after several seconds.

• The SRS warning light comes on while
you are driving.

 To ensure that the passenger’s seat occu-

pant classification sensor system can sense
correctly, observe the following instruc­tions. Failure to follow these instructions
can adversely affect the performance of
the passenger’s airbag system.

• Adjust the seat to the correct position,
and sit well back against the seatback.
Refer to “Front seats” on page 4-4.

• Do not recline the seatback more than
necessary.

• Never have more than one person (adult
or child) sitting on the seat.

• Do not place anything between the seat
and the floor console.

• When attaching a child restraint system,
secure it firmly.

• Do not place luggage or other objects on
the seat.

• Do not use a seat cover or a cushion.

• Do not modify or replace the seat and
seat belt.

• Do not place luggage or other objects
under the seat.

• Do not place and use an electronic device
such as a computer on the seat.

• Do not place heavy objects on the seat or
stick pins, needles, or other objects into
it.

• Do not remove the seat cushion skin.

• If any liquid is spilled on the seat, wipe it
and dry the seat immediately.

 If the vehicle is involved in a severe

impact, have the SRS sensors inspected by
an authorized Mitsubishi Motors dealer as
soon as possible.

Passenger’s airbag off indicator

N00418101346

The passenger’s airbag off indicator is
located in the instrument panel.

The indicator normally comes on when the
ignition switch is turned to the “ON” position
or the operation mode is put in ON, and goes
out a few seconds later. In the following situ­ations, the indicator will stay on to show that
the passenger front airbag is not operational.

 The front passenger’s seat is not occupied.

4-40 Seat and restraint systems

4

WAR N ING

WAR N ING

Type 1

Type 2

WAR N ING

 The system senses that a child is using a

child restraint system on the front passen­ger’s seat.

When the passenger’s seat occupant classifi­cation sensor system sense there is a person
seated in the front passenger’s seat, the indi­cator goes out to show that the passenger’s
front airbag is operational.

 If any of the following conditions occur,

you should immediately have the airbag
system in your vehicle inspected by an
authorized Mitsubishi Motors dealer as
soon as possible:

• The passenger’s airbag off indicator
comes on when an adult is sitting on the
front passenger seat.

• The passenger’s airbag off indicator does
not come on when the front passenger
seat is not occupied.

• The passenger’s airbag off indicator does
not come on when the ignition switch is
turned to the “ON” position or the oper­ation mode is put in ON.

• The passenger’s airbag off indicator does
not come on when a child is in a child
restraint system on the front passenger’s
seat.

• The passenger’s airbag off indicator
comes on and goes out repeatedly.

 Do not attach any accessory to your vehi-

cle that makes the passenger’s airbag off
indicator difficult or impossible to see.
You must be able to see the passenger’s
airbag off indicator and verify the status
of the passenger’s airbag system.

SRS warning light/display

N00408301589

There is a Supplemental Restraint System
(SRS) warning light on the instrument panel.

The system checks itself every time the igni­tion switch is turned to the “ON” position or
the operation mode is put in ON. The SRS
warning light will come on for several sec-

Supplemental Restraint System (SRS) - airbag

onds and then go out. This is normal and
means the system is working properly.
If there is a problem involving one or more of
the SRS components, the warning light will
come on and stay on. At the same time, the
warning display will appear on the informa­tion screen in the multi information display
(Type 1 only).
The SRS warning light/display is shared by
the SRS airbag and the seat belt pre-tensioner
system.

 If any of the following conditions occur,

there may be a problem with the SRS air­bags and/or seat belt pre-tensioners, and
they may not function properly in a colli­sion or may suddenly activate without a
collision:

•Even when the ignition switch or the
operation mode is in ON, the SRS warn­ing light does not come on or it remains
on.

• The SRS warning light and/or the warn­ing display comes on while driving.

The SRS airbags and seat belt pre-ten­sioners are designed to help reduce the
risk of serious injury or death in certain
collisions. If either of the above conditions
occurs, immediately have your vehicle
checked by an authorized Mitsubishi
Motors dealer.

Seat and restraint systems 4-41

Supplemental Restraint System (SRS) - airbag

4

Driver

Front passenger

Driver’s and passenger’s front
airbag system

N00407901331

The driver’s airbag is located under the pad­ded cover in the middle of the steering wheel.
The front passenger’s airbag is contained in
the instrument panel above the glove com­partment. The driver’s airbag and the front
passenger’s airbag are designed to deploy at
the same time. However, the front passen­ger’s airbag does not deploy when the front
passenger seat is not occupied or when the
system senses that a child is in the child
restraint system.

designed to deploy at the same time as the
driver’s front airbag.

Driver’s knee airbag system

The driver’s knee airbag is located under the
steering wheel. The driver’s knee airbag is

4-42 Seat and restraint systems

N00404500010

Supplemental Restraint System (SRS) - airbag

4

Head-on collision with a solid wall at speeds of
approx. 15 mph (25 km/h) or higher

Moderate to severe frontal impact within the shaded
area between the arrows

Deployment of front airbags

N00408001616

The front airbags and driver’s knee airbag ARE DESIGNED TO DEPLOY when …

The front airbags and driver’s knee airbag are
designed to deploy when the vehicle suffers a
moderate to severe frontal impact. A typical
condition is shown in the illustration to the
left.

The front airbags and driver’s knee airbag are
designed to deploy only in certain moderate
to severe frontal collisions within the shaded
area between the arrows in the illustration to
the right.

The front airbags and driver’s knee airbag
will deploy if the impact to the vehicle’s main
structure is above a specific threshold level.
The threshold level is approximately 15 mph
(25 km/h) for a frontal collision straight into a
solid flat wall that does not bend or deform. If
the impact to the vehicle’s main structure is
below this threshold level, the front airbags
and driver’s knee airbag may not deploy. This
threshold level may also be higher if the vehi­cle hits something that absorbs the impact,
either by bending or moving (for example,

another stationary vehicle, a pole or a guard
rail).
The initial stage of airbag inflation is the
most forceful, and can cause serious injury or
death if you are too close to the deploying air­bag. Accordingly, it is important that you
always wear the available seat belt.

Seat and restraint systems 4-43

Supplemental Restraint System (SRS) - airbag

4

Collision with a utility pole, tree or other
narrow object

Collision where the vehicle slides under the
rear body of a truck

Oblique frontal impact

Rear end collision to your vehicle

Side collision to your vehicle

Vehicle rolls onto its side or roof

The front airbags and driver’s
knee airbag MAY NOT DEPLOY
when …

they cannot provide protection to the occu­pants.
Some typical situations are shown in the
illustration.

In certain types of front collisions, the front
airbags and driver’s knee airbag may not
deploy, even if the deformation of the body
seems to be large, because the vehicle’s body
structure is designed to absorb the impact and
deform in order to help protect the occupants.
Some typical situations where the front air­bags and driver’s knee airbag may not deploy
are shown in the illustrations.

Since the front airbags and driver’s knee air­bag do not protect the occupant in all types of
frontal collisions, be sure to always wear your
seat belts properly.

Since the front airbags and driver’s knee air­bag do not protect the occupants in all types
of collisions, be sure to always wear your seat
belts properly.

The front airbags and driver’s
knee airbag ARE NOT
DESIGNED TO DEPLOY when
…

The front airbags and driver’s knee airbag are
not designed to deploy in situations where

4-44 Seat and restraint systems

4

The front airbags and driver’s

Collision with an elevated median/island or
curb

Vehicle travels over a deep hole/pothole

Vehicle drives down a steep slope and hits the
ground

WAR N ING

WAR N ING

knee airbag MAY DEPLOY when
…

The front airbags and driver’s knee airbag
may deploy if the underside of the vehicle
suffers a moderate to severe impact (under­carriage impact). Some typical situations are
shown in the illustration.

Since the front airbags and driver’s knee air­bag may deploy in certain types of unex­pected impacts, as shown in the illustrations,
and these unexpected impacts can move you
out of position, it is important to always wear
your seat belts properly. When worn properly,
seat belts can help maintain your distance
from the airbags when they begin to inflate.
The initial stage of airbag inflation is the
most forceful and can cause serious injury or
death if you are close to the deploying airbag.

Supplemental Restraint System (SRS) - airbag

 Do not attach anything to the steering

wheel’s padded cover, such as trim mate­rial, badges, etc. These could strike and
injure an occupant if the airbag inflates.

 Do not set anything on, or attach anything

to, the instrument panel above the glove
compartment. Such items could strike and
injure an occupant if the airbag inflates.

 Do not attach accessories to, or put them

in front of, the windshield. They could
restrict the airbag inflation, or strike and
injure an occupant, when the airbag
inflates.

Seat and restraint systems 4-45

Supplemental Restraint System (SRS) - airbag

4

WAR N ING

WAR N ING

WAR N ING

 Do not attach additional keys or accesso-

ries (hard, pointed or heavy objects) to the
ignition key. Such objects could prevent
the driver’s knee airbag from inflation
normally or could be propelled to cause
serious injury if the airbag inflates.

 Do not attach accessories to the lower por-

tion of the driver’s side instrument panel.
Such objects could prevent the driver’s
knee airbag from inflating normally or
could be propelled to cause serious injury
if the airbag inflates.

 Do not place objects, such as packages or

pets, between the airbags and the driver
or the front passenger. Such objects can
adversely affect airbag performance, or
cause serious injury or death when the
airbag deploys.

 Immediately after airbag inflation, some

parts of the airbag system will be hot. Do
not touch them. You could otherwise be
burned.

 The airbag system is designed to work

only once. After the airbags deploy, they
will not work again. They must promptly
be replaced and the entire airbag system
must be inspected by an authorized Mit­subishi Motors dealer.

Side airbag system

N00408101431

The side airbags (A) are contained in the
driver and front passenger seatbacks.
The side airbag is designed to inflate only on
the side of the vehicle that is impacted, even
with no passenger in the front seat.

A label is attached to the seatbacks in vehi­cles equipped with side airbags.

 Do not attempt to remove, install, disas-

semble or repair the SRS airbags.

4-46 Seat and restraint systems

Supplemental Restraint System (SRS) - airbag

4

WAR N ING

WAR N ING

WAR N ING

Curtain airbag system

N00419201315

The curtain airbags are contained in the front
pillar, the rear pillar and the side sections of
the roof.
The curtain airbag is designed to inflate only
on the side of the vehicle that is impacted,
even with no passenger in the seat.
Also, when the airbag control unit detects
rollover of the vehicle, the curtain airbags
will deploy.

 The side airbags and curtain airbags can

cause serious injury or death to anyone
too close to the airbag when it deploys. To
reduce the risk of injury from a deploying
side airbag or curtain airbag, driver and
front passenger must be properly
restrained and seated well back, upright,
and in the middle of the seat. Do not lean
against the door.

 In order to reduce the risk of injury from

a deploying side airbag, do not allow any
second row seat passengers to hold onto
the back of either front seat. Special care
should be taken with children.

 Do not place any objects around the area

where the side airbags deploy. Such
objects can interfere with proper side air­bag deployment, and cause injury during
deployment of the side airbag.

 Do not place stickers, labels or additional

trim on the back of either front seat. They
can interfere with proper side airbag
deployment.

 Do not attach a microphone (A) or any

other object around the part where the
curtain airbag (B) deploys, such as on the
windshield, side door glass or front and
rear pillars and roof side rail. When the
curtain airbag inflates, the microphone or
other object may be hurled with great
force or the curtain airbag may not inflate
correctly, resulting in death or serious
injury.

Seat and restraint systems 4-47

Supplemental Restraint System (SRS) - airbag

4

WAR N ING

WAR N ING

Moderate to severe impact to the middle of the
vehicle body’s side structure

When the vehicle detects rollover of the vehicle
(Curtain airbag only)

 Do not put a hanger or any heavy or

pointed object on the coat hook. If the cur­tain airbag was activated, any such item
could be propelled away with great force
and could prevent the curtain airbag from
inflating correctly. Hang clothes directly
on the coat hook (without using a hanger).
Make sure there are no heavy or sharp
objects in the pockets of clothes that you
hang on the coat hook.

 Do not install seat covers or re-cover seats

that have side airbags. Covers can inter­fere with proper side airbag deployment
and adversely affect side airbag perfor­mance.

 Never install a rear-facing child restraint

system in the front passenger seat. Rear­facing child restraint systems MUST
ONLY be used in the rear seat.

 Front-facing child restraint systems

should also be used ONLY in the rear seat.
If a front-facing child restraint system
must be used in the front passenger seat,
move the seat as far back as possible, and
make sure that the child stays in the child
restraint system, properly restrained and
away from the door.

 Do not allow a child to lean against or sit

close to the passenger door, even if the
child is seated in a child restraint system.
The child’s head should also not lean
against or be close to the section of the
seatback where the side airbag and cur­tain airbag are located. It is dangerous if
the side airbag or curtain airbag deploys.
Failure to follow all of these instructions
could lead to serious injury or death to the
child.

 Work done on or in the vicinity of the side

airbag or curtain airbag components
should be done only by an authorized Mit­subishi Motors dealer. There is a risk of a
serious injury or death. Improper work
methods can cause accidental side airbag
or curtain airbag deployment, or render a
side airbag or curtain airbag inoperable.
Either of these situations could result in
serious injury or death.

Deployment of side airbag and
curtain airbag

N00408201591

The side airbag and curtain airbag
ARE DESIGNED TO DEPLOY
when...

The side airbag and curtain airbag are
designed to deploy when the vehicle suffers a
moderate to severe side impact to the middle
of the passenger compartment.
Also when the vehicle detects rollover of the
vehicle, the curtain airbags will deploy.
Typical situations are shown in the illustra­tion.

4-48 Seat and restraint systems

4

The seat belts in your vehicle are your pri-

Side impact in an area away from the passenger
compartment

Motorcycle or other similar small vehicle
collision with the side of vehicle

Collision with a utility pole, tree or other
narrow object

Oblique side impact

Vehicle rolls onto its side or roof (Side airbag
only)

mary means of protection in an accident. The
SRS side airbags and curtain airbags are
designed to provide additional protection.
Therefore, for your safety and the safety of all
occupants, be sure to always wear your seat
belts properly.

The side airbag and curtain airbag
MAY NOT DEPLOY when...

In certain types of side collisions, the side air­bag and curtain airbag may not deploy, even
if the deformation of the body seems to be
large, because the vehicle’s body structure is
designed to absorb the impact and to deform
in order to help protect the occupants. There
are also cases where the side airbag and cur­tain airbag may not deploy at the same time,
depending on the location of the impact.
Some typical situations where the side air­bags and curtain airbags may not deploy are
shown in the illustrations.

Supplemental Restraint System (SRS) - airbag

Since the side airbags and curtain airbags do
not protect the occupant in all types of side
collisions, be sure to always wear the seat
belts properly.

The side airbag and curtain airbag
ARE NOT DESIGNED TO
DEPLOY when...

The side airbag and curtain airbag are not
designed to deploy in situations where they
cannot provide protection to the occupants.
Some typical situations are shown in the
illustration.

Seat and restraint systems 4-49

Supplemental Restraint System (SRS) - airbag

4

Head-on collision

Rear end collision to your vehicle

Pitch end over end

WAR N ING

NOTE

WAR N ING

Since the side airbags and curtain airbags do
not protect the occupant in all types of colli­sions, be sure to always wear your seat belts
properly.

SRS servicing

N00408500669

 Any maintenance performed on or near

the components of the SRS should be per­formed only by an authorized Mitsubishi
Motors dealer. Do not permit anyone else
to do any service, inspection, maintenance
or repair on any SRS components or wir­ing. Similarly, no part of the SRS should
ever be handled, removed or disposed by
anyone except an authorized Mitsubishi
Motors dealer.
Improper work methods on the SRS com­ponents or wiring could result in an acci­dental airbag deployment or could make
the SRS inoperable. Either of these situa­tions could result in serious injury or
death.

 Do not modify your steering wheel or any

other SRS component or related vehicle
part. For example, replacement of the
steering wheel, or modifications to the
front bumper or body structure can
adversely affect SRS performance and
may lead to injury.

 If your vehicle has received any damage,

you should have the SRS inspected by an
authorized Mitsubishi Motors dealer to
make sure it is in proper working order.

 Do not modify your front seats, center pil-

lar or center console. Such modifications
can adversely affect SRS performance and
may lead to injury.
Also, if you discover any tear or open
seam in the seat fabric near the side air­bag, have the seat inspected by an autho­rized Mitsubishi Motors dealer.

 If you have found any scratch, crack or

damage to the portion of the front and
rear pillars and roof side rail, you should
have the SRS inspected by an authorized
Mitsubishi Motors dealer.

 When you transfer ownership of the vehicle

to another person, we urge you to alert the
new owner that it is equipped with the SRS
and refer that owner to the applicable sec­tions in this owner’s manual.

 If you decide to junk or scrap your vehicle,

we urge you to first take it to an authorized
Mitsubishi Motors dealer so that the SRS can
be made safe for disposal.

 If any of the following parts needs to be

modified for use by a handicapped person,
the advanced airbag system will be greatly
affected. Please consult an authorized Mit­subishi Motors dealer.

• Driver’s seat

• Front passenger seat

• Front seat belt

4-50 Seat and restraint systems

Supplemental Restraint System (SRS) - airbag

4

NOTE

• Steering wheel

• Instrument panel

[For vehicles sold in U.S.A.]

To contact Mitsubishi Motors North
America, Inc.
call 1-888-648-7820 or write to:

Mitsubishi Motors North America, Inc.
Customer Relations Department
P.O. Box 6400
Cypress, CA 90630-0064

[For vehicles sold in Canada]

To contact Mitsubishi Motor Sales of
Canada, Inc.
call 1-888-576-4878 or write to:

Mitsubishi Motor Sales of Canada, Inc.
Customer Relations Department
P.O. Box 41009
4141 Dixie Road
Mississauga, ON L4W 5C9

[For vehicles sold in Puerto Rico]

To contact Mitsubishi Motor Sales of
Caribbean, Inc.
call 1-787-251-8715 or write to:

Mitsubishi Motor Sales of Caribbean,
Inc.
Customer Service Department
P.O. Box 192216
SAN JUAN PR 00919-2216

[For vehicles sold in Guam]

To contact Triple J Enterprises Inc.
call [phone] or write to:

Triple J Enterprises, Inc.
P.O. Box 6066
TAMUNING
GUAM 96931

[For vehicles sold in Saipan]

To contact Triple J Motors
call [phone] or write to:

Triple J Motors
P.O. Box 500487
SAIPAN, MP96950-0487

[For vehicles sold in American Samoa]

To contact Pacific Marketing Inc.
call 684 (699) 9140 or write to:

Pacific Marketing, Inc.
P.O. Box 698
PAG O PA GO,
AMERICAN SAMOA AS, 96799

Seat and restraint systems 4-51

Supplemental Restraint System (SRS) - airbag

4

Warning label

N00408600354

Occupant restraint warning labels for the SRS
are located in the vehicle as shown in the
illustration.

* - Located in the passenger’s side as well.

4-52 Seat and restraint systems

5

Features and controls

Break-in recommendations ..............................................................5-3

Keys .................................................................................................5-3

Electronic immobilizer (Anti-theft starting system) ........................5-4

Keyless entry system (if so equipped) ..............................................5-7

Free-hand Advanced Security Transmitter (F.A.S.T.-key)

(if so equipped) ..........................................................................5-13

Door locks ......................................................................................5-34

Power door locks ...........................................................................5-36

Child safety locks for rear door .....................................................5-37

Liftgate (except for vehicles equipped with the power liftgate) ....5-38

Power liftgate (if so equipped) .......................................................5-39

Inside liftgate release .....................................................................5-46

Theft-alarm system ........................................................................5-46

Power window control ...................................................................5-49

Sunroof (if so equipped) .................................................................5-51

Parking brake .................................................................................5-53

Steering wheel height and reach adjustment ..................................5-57

Inside rearview mirror ...................................................................5-57

Outside rearview mirrors ...............................................................5-60

Ignition switch (if so equipped) ......................................................5-63

Steering wheel lock (if so equipped) ..............................................5-65

Starting the engine .........................................................................5-66

Automatic transaxle (if so equipped)..............................................5-68

Continuously variable transmission (CVT) (if so equipped)..........5-75

Electronically controlled 4WD system (if so equipped).................5-82

S-AWC (Super-All Wheel Control) (if so equipped) .....................5-85

4-wheel drive operation .................................................................5-88

Inspection and maintenance following rough road operation ........5-91

Cautions on the handling of 4-wheel drive vehicles ..................... 5-91

Service brake ................................................................................. 5-92

Brake auto hold (if so equipped) ....................................................5-93

Hill start assist (if so equipped) ......................................................5-95

Brake assist system ........................................................................ 5-96

Anti-lock braking system .............................................................. 5-97

Electric power steering system (EPS) ...........................................5-99

Active stability control (ASC) ..................................................... 5-100

Cruise control (if so equipped) ..................................................... 5-103

Adaptive Cruise Control System (ACC) (if so equipped)............ 5-107

Forward Collision Mitigation System (FCM) (if so equipped).... 5-118

Blind Spot Warning (BSW) (with Lane Change Assist)

(if so equipped) ........................................................................ 5-126

Rear Cross Traffic Alert (RCTA) (if so equipped) .......................5-131

Lane Departure Warning System (LDW) (if so equipped)........... 5-134

Tire pressure monitoring system .................................................5-137

Rear-view camera (if so equipped)...............................................5-142

Multi Around Monitor (if so equipped)........................................5-144

Instrument cluster ........................................................................ 5-154

Multi Information display - Type 1 ............................................. 5-155

Multi Information display - Type 2 ............................................. 5-173

Indicator light, warning light, and information

screen display list (multi information display - Type 1) .......... 5-181

Indicator and warning light package

(multi information display - Type 2) ....................................... 5-201

Indicators .....................................................................................5-202

Warning lights ..............................................................................5-203

5

Features and controls

Information screen display

(Vehicle equipped with the multi information display - Type 1)

.................................................................................................. 5-206

Combination headlights and dimmer switch ............................... 5-207

Headlight leveling switch (if so equipped) .................................. 5-216

Turn signal lever .......................................................................... 5-217

Hazard warning flasher switch .................................................... 5-218

ECO mode switch ........................................................................ 5-218

Front fog light switch (if so equipped) ......................................... 5-218

Wiper and washer switch ............................................................ 5-219

Wiper deicer switch (if so equipped)............................................ 5-224

Electric rear window defogger switch ......................................... 5-225

Heated steering wheel switch (if so equipped)............................. 5-226

Horn switch ................................................................................. 5-227

Link System ................................................................................. 5-227

USB input terminal ...................................................................... 5-227

Sun visors .................................................................................... 5-229

12 V power outlets ...................................................................... 5-230

HomeLink

Interior lights ............................................................................... 5-236

Storage spaces ............................................................................. 5-239

Cup holders ................................................................................. 5-242

Bottle holders .............................................................................. 5-243

Cargo area cover (if so equipped) ............................................... 5-244

Assist grips .................................................................................. 5-246

Coat hooks ................................................................................... 5-246

Luggage hooks ............................................................................ 5-246

®

Wireless Control System (if so equipped) ............... 5-231

Break-in recommendations

5

NOTE

Break-in recommendations Keys

N00508701366

Advanced automobile manufacturing tech­niques permit you to operate your new vehi­cle without requiring a long break-in period
of low-speed driving.
However, you can add to the future perfor­mance and economy of your vehicle by
observing the following precautions during
the first 300 miles (500 km).
Drive your vehicle at moderate speeds during
the break-in period.

 Avoid revving the engine.
 Avoid rough driving such as sudden starts,

sudden acceleration, prolonged high­speed driving and sudden braking. These
actions would have a detrimental effect on
the engine and lead to increased fuel and
oil consumption; this could ultimately
result in the malfunction of engine com­ponents. Be particularly careful to avoid
full acceleration while in low shift posi­tion (low gears).

 Do not overload the vehicle. Stay within

the seating capacity. (Refer to “Cargo load
precautions” on page 6-10.)

 Refrain from towing a trailer or other

vehicle (Refer to “Trailer towing” on page
6-11).

Type 1

Two keys are provided. The keys fit all locks.
Keep one in a safe place as a spare key.

1- Key for the electronic immobilizer and

keyless entry system

2- Key number plate

N00508801716

Type 2

Two F.A.S.T.-keys and two emergency keys
are provided.
Keep one F.A.S.T.-key and one emergency
key in a safe place together as a set of spare
keys.

1- F.A.S.T.-key

(with electronic immobilizer and key-

less entry system function)
2- Emergency key
3- Key number plate

 The key is a precision electronic device with

a built-in signal transmitter. Please observe
the following in order to prevent damage.

• Do not leave where it may be exposed to
heat caused by direct sunlight, such as on
top of the dashboard.

Features and controls 5-3

Electronic immobilizer (Anti-theft starting system)

5

NOTE

CAUTION

NOTE

NOTE

• Do not take the remote control transmitter
apart.

• Do not excessively bend the key or subject
it to strong impacts.

• Keep the remote control transmitter dry.

• Keep away from magnetic objects such as
key rings.

• Keep away from devices that produce mag­netism, such as audio systems, computers
and televisions.

• Keep away from devices that emit strong
electromagnetic waves, such as cellular
phones, wireless devices and high fre­quency equipment (including medical
devices).

• Do not clean with ultrasonic cleaners.

• Do not leave the key where it may be
exposed to high temperature or high humid­ity.

 If you lose your key, to prevent the theft of

the vehicle immediately contact an autho­rized Mitsubishi Motors dealer.
If you notify an authorized Mitsubishi
Motors dealer of the key number, they can
make a new key. The key number is stamped
on the key number plate. Keep the key num­ber plate in a safe place separate from the
key itself.

 No keys other than those registered in

advance can be used to start the engine.
Refer to “Electronic immobilizer (Anti-theft
starting system)” on page 5-4.
Refer to “Free-hand Advanced Security
Transmitter (F.A.S.T.-key): “Electronic
immobilizer (Anti-theft starting system)” on
page 5-18.

 When the theft-alarm is in the system opera-

tional status, the alarm operates if a door or
liftgate is opened after using the key, the
door lock knob or the power door lock
switch to unlock the vehicle.

 The system does not enter the preparation

status if the keyless entry system or the
F.A.S.T.-key operation was not used to lock
the vehicle.

Electronic immobilizer
(Anti-theft starting system)

N00509101891

 Do not make any alterations or additions to

the immobilizer system. Alterations or addi­tions could cause failure of the immobilizer.

[For vehicles equipped with the Free-hand
Advanced Security Transmitter (F.A.S.T.­key)]

For information on operations for vehicles
equipped with the Free-hand Advanced Secu­rity Transmitter (F.A.S.T.-key), refer to
“Free-hand Advanced Security Transmitter
(F.A.S.T.-key): Electronic immobilizer (Anti­theft starting system)” on page 5-18.

[Except for vehicles equipped with the Free­hand Advanced Security Transmitter
(F.A.S.T.-key)]
The electronic immobilizer is designed to sig­nificantly reduce the possibility of vehicle
theft. The purpose of the system is to immo­bilize the vehicle if an invalid start is
attempted. A valid start attempt can only be
achieved (subject to certain conditions) using
a key “registered” to the immobilizer system.
All of the keys provided with your new vehi­cle have been programmed to the vehicle’s
electronics.

 In the following cases, the vehicle may not

be able to recognize the registered ID code
from the key. This means the engine will not
start even when the key is turned to the
“START” position.

5-4 Features and controls

Electronic immobilizer (Anti-theft starting system)

5

NOTE

NOTE

NOTE

Take your vehicle and all remaining keys to

• When the key contacts a key ring or other
metallic or magnetic object

• When the key grip contacts metal of
another key

 In cases like the above, move the offending

object(s) away from the key and turn the key
back to the “ACC” or “LOCK” position.
Then try to start the engine again. If the
engine does not start, contact an authorized
Mitsubishi Motors dealer.

 The key may not operate properly when it is

near an object or facility that emits strong
electromagnetic waves.

 Electronic immobilizer is not compatible

with commercially available remote starting
systems. Use of commercially available
remote starting systems may result in vehicle
starting problems and a loss of security pro­tection.

 A system failure is suspected when the igni-

tion switch is turned to the “START” posi­tion, and the engine does not start. In such a
case, contact an authorized Mitsubishi
Motors dealer.

your authorized Mitsubishi Motors dealer to
have your ID code changed.

Additional keys

To add a key, you must already have 2 regis­tered keys. You need to register the ID code
to the vehicle.
Registering the ID code can be done by your­self (except for vehicles sold in Canada), or
by your authorized Mitsubishi Motors dealer.
For you to register the ID code yourself, fol­low the “Customer key programming” proce­dure below.
If you choose to have your authorized Mit­subishi Motors dealer register the ID code,
take your vehicle and all remaining keys to
your authorized Mitsubishi Motors dealer.

• When the key contacts or is close to other
immobilizer keys (including keys of other
vehicles)

Replacement keys

Only keys that have been programmed to the
vehicle’s electronics can be used to start the
vehicle.

If you lose the key, you can order a key from
your authorized Mitsubishi Motors dealer by
referring to the key number.
To prevent vehicle theft, the ID code for the
vehicle keys must be changed.

 You are provided with 2 keys, but you may

register up to 8 keys.

Features and controls 5-5

Electronic immobilizer (Anti-theft starting system)

5

NOTE

Customer key programming
(Except for vehicles sold in
Canada)

N00562201149

You can program new keys to the system if
you have two valid (already registered) keys
and blank immobilizer key (specially cut for
your vehicle at your Mitsubishi Motors
dealer) by doing the following:

1. Insert the first valid key into the ignition
switch and turn the key to the “ON” posi­tion for 5 seconds.

2. Turn the key to the “OFF” or “LOCK”
position and remove the first key.

3. Within 30 seconds of removing the first
key, insert the second valid key into the
ignition and turn it to the “ON” position.
About 10 seconds later, the immobilizer
display will start to blink.

4. When the immobilizer display starts
blinking, turn the second valid key to the
“OFF” or “LOCK” position and remove
it. Within 30 seconds after doing so, insert
a blank immobilizer key into the ignition
switch and turn it to the “ON” position.
Perform this operation no more than 30
seconds after the immobilizer display
starts blinking. When registration of the
ID code is complete, the immobilizer dis­play will come on for 30 seconds then go
off. If an error occurs, the blinking immo­bilizer display will go off during the pro­cedure.

Type 1

Type 2

5. If you wish to register another key, per­form the process again from step 1.

 Perform the operation when the interrupt dis-

play screen is not showing. The interrupt dis­play screen may prevent you from seeing the
immobilizer display.

 It is not possible to register a key if:

• the immobilizer display goes off during the
procedure

• the immobilizer display does not come on
within 30 seconds after step 4.

 The procedure will be terminated automati-

cally if:

• a period of 30 seconds or longer elapses
from the moment when the first key is
turned to the “OFF” or “LOCK” position to
the moment when the second key is turned
to the “ON” position

• a period of 30 seconds or longer elapses
from the moment when the second key is
turned to the “OFF” or “LOCK” position to
the moment when the blank immobilizer
key is turned to the “ON” position

 To use the new remote control transmitters, it

is necessary to register the key with both the
electronic immobilizer and keyless entry sys­tem.
Also refer to “Keyless entry system: Cus­tomer remote control transmitter program­ming” on page 5-10.

5-6 Features and controls

Keyless entry system (if so equipped)

5

CAUTION

NOTE

NOTE

General information

N00562301094

Your electronic immobilizer operates on a
radio frequency subject to Federal Communi­cations Commission (FCC) Rules (For vehi­cles sold in U.S.A.) and Industry Canada
Rules (For vehicles sold in Canada). This
device complies with part 15 of FCC Rules
and Industry Canada licence-exempt RSS
standard(s).
Operation is subject to the following two con­ditions.

 This device may not cause harmful inter-

ference.

 This device must accept any interference

received, including interference that may
cause undesired operation.

 Changes or modifications not expressly

approved by the manufacturer for compli­ance could void the user’s authority to oper­ate the equipment.

Keyless entry system (if so

equipped)

N00509002031

Press the remote control transmitter buttons
to lock or unlock the doors and the liftgate.
It can also help you signal for attention by
setting off the panic alarm.

1-

LOCK ( ) button

2-

UNLOCK ( ) button
3- PANIC button
4- Indicator light

 On vehicles equipped with the mirror retrac-

tor switch, the outside rearview mirrors auto­matically retract or extend when the doors
and the liftgate are locked or unlocked using
the remote control switches of the keyless
entry system.
Refer to “Features and controls: Outside
rearview mirrors” on page 5-60.

To l oc k

Press the LOCK button (1) to lock all the
doors and the liftgate.
The turn signal lights will also blink once.

 On vehicles equipped with the mirror retrac-

tor switch, the outside rearview mirrors auto­matically retract when the LOCK button(1)
is pressed.

 If you press the LOCK button (1) twice the

horn will sound once.

To unlock

Press the UNLOCK button (2) to unlock the
driver’s door only.

Features and controls 5-7

Keyless entry system (if so equipped)

5

NOTE

NOTE

Within approximately 2 seconds, press the
UNLOCK button one more time to unlock all
the doors and liftgate.
The dome light will turn on for 30 seconds.
The turn signal lights will also blink twice.
The front side-marker and parking lights will
also turn on for approximately 30 seconds.
Refer to “Welcome light” on page 5-215.

 On vehicles equipped with the mirror retrac-

tor switch, the outside rearview mirrors auto­matically extend when the UNLOCK
button(2) is pressed.

 On vehicles equipped with the Smartphone

Link Display Audio, the functions can be
adjusted on the screen. For details, refer to
the separate owner’s manual.

 The door and liftgate unlock function can be

set so that all doors and liftgate unlock when
the UNLOCK button (2) is pressed once.
Refer to “Setting of door and liftgate unlock
function” on page 5-9.

Operation of the outside rear­view mirrors (Vehicles
equipped with the mirror
retractor switch)

To re tr a ct

Within 30 seconds of locking the doors and
liftgate using the LOCK button, press the
LOCK button twice rapidly to retract the out­side rearview mirrors.

To e x te nd

Within 30 seconds of unlocking the doors and
liftgate using the UNLOCK button, press the
UNLOCK button twice rapidly to return the
outside rearview mirrors to their extended
positions.

The outside rearview mirrors are not initially
set to work as described above. If you want
them to work as described above, you need to
set them so that they do not retract/extend
when the doors and liftgate are
locked/unlocked using the keyless entry sys­tem.
For details, please consult an authorized Mit­subishi Motors dealer.

In a vehicle equipped with the Smartphone
Link Display Audio, it is possible to change
the setting by means of screen operations.
Refer to the separate owner’s manual for
details.

Answerback function

The horn and turn signal lights of the keyless
entry system answerback function can be
changed as required. This is done with the
key removed from the ignition switch.

 The answerback function will not operate if

any of the doors are open.

Horn deactivation/reactivation

The answerback function can be set in the
following three ways.
Each time the answerback function is set, a
chime will sound to tell you the condition of
the answerback function.

One chime: The horn will not sound.
Two chimes: The horn will sound.
Four chimes: The horn will sound if the

LOCK button is pressed twice
within 1 second.

5-8 Features and controls

Keyless entry system (if so equipped)

5

NOTE

NOTE

NOTE

1. Remove the key from the ignition switch.

2. Open the driver’s door and turn the com­bination headlights and dimmer switch to
the “OFF” position.

3. Press the LOCK button (1) for 4 to 10 sec­onds and press the UNLOCK button (2)
during this time.

4. Release in sequence the UNLOCK and
LOCK buttons within 5 seconds of press­ing the UNLOCK button in step 3.

 On a vehicle equipped with the Smartphone

Link Display Audio, the functions can be
adjusted on the screen. For details, refer to
the separate owner’s manual.

4. Release in sequence the UNLOCK and
LOCK buttons within 5 seconds of press­ing the LOCK button in step 3.

Number of
chimes

One chime One flash Two flashes

Two chimes One flash No flash

Three chimes No flash Two flashes

Four chimes Two flashes One flash

Five chimes No flash One flash

Six chimes Two flashes No flash

Seven
chimes

To lo c k To un l o c k

No flash No flash

Turn signal lights deactiva­tion/reactivation

The answerback function can be turned ON
or OFF separately.

1. Remove the key from the ignition switch.

2. Open the driver’s door and turn the com­bination headlights and dimmer switch to
the “OFF” position.

3. Press the UNLOCK button (2) for 4 to 10
seconds and press the LOCK button (1)
during this time.

 On a vehicle equipped with the Smartphone

Link Display Audio, the functions can be
adjusted on the screen. For details, refer to
the separate owner’s manual.

Setting of door and liftgate
unlock function

N00543601173

The door and liftgate unlock function can be
set to the following two conditions.
Each time the door and liftgate unlock func­tion is set, a chime will sound to tell you the

condition of the door and liftgate unlock
function.

Number of

chimes

One chime

Two chimes Driver’s door unlock only

1. Remove the key from the ignition switch.

2. Open the driver’s door and turn the com­bination headlights and dimmer switch to
the “OFF” position.

3. Press the LOCK button (1) for 4 to 10 sec­onds and press the UNLOCK button (2)
during this time.

4. Release in sequence the LOCK and
UNLOCK buttons within 10 seconds of
pressing the LOCK button in step 3.

 On a vehicle equipped with the Smartphone

Link Display Audio, the functions can be
adjusted on the screen. For details, refer to
the separate owner’s manual.

All doors and the liftgate
unlock

Condition

Features and controls 5-9

Keyless entry system (if so equipped)

5

NOTE

Using the panic alarm

If you are near your vehicle and feel threat­ened, you may activate the alarm to call atten­tion as follows:

1. Press the PANIC button (3) for more than
1 second.

2. The headlights will blink on and off and
the horn will sound intermittently for
about 3 minutes.

3. To turn off the alarm, press any button on
the remote control transmitter.

Replacement remote control
transmitters

Only remote control transmitters pro­grammed with the vehicle’s electronics can
lock or unlock all doors and the liftgate.

If you lose the remote control transmitter, you
can order a remote control transmitter from
your authorized Mitsubishi Motors dealer by
referring to the key number.
To prevent vehicle theft, the ID code for the
remote control transmitter must be changed.
Take your vehicle and all remote control
transmitters to your authorized Mitsubishi
Motors dealer to have your ID code changed.

N00543701060

N00543801087

Additional remote control
transmitters

N00543900049

To add a remote control transmitter, you must
already have 1 registered remote control
transmitter.
Registering the ID code can be done by your­self or by your authorized Mitsubishi Motors
dealer. For you to register the ID code your­self, follow the “Customer remote control
transmitter programming” procedure below.
If you choose to have your authorized
Mitsubishi Motors dealer register the ID
code, take your vehicle and any remaining
keys to your authorized Mitsubishi Motors
dealer.

 You are provided with 2 remote control

transmitters, but you may register up to 8
remote control transmitters.

Customer remote control trans­mitter programming (Except
for vehicles sold in Canada)

N00544001204

You can program new remote control trans­mitters to the system if you have one valid

(already registered) remote control transmit­ter by doing the following:

1. Have available all (current and new)
remote control transmitters you wish to
register.

2. With a valid (already registered) remote
control transmitter, press the UNLOCK
button (2) for 4 to 10 seconds. Then press
and hold the LOCK button (1).

3. Within 10 seconds of pressing the LOCK
button, release the LOCK and UNLOCK
buttons in sequence.
At this time, ID codes for all remote con­trol transmitters except for the transmitter
used in steps 2 and 3 are erased and the
answerback function (door is locked and
unlocked) informs you that the registra­tion mode has been activated.

4. Within 60 seconds after step 3, complete
the following ID code registration opera­tion using the next remote control trans­mitter you wish to register within 4
seconds.
i) Press both the LOCK and UNLOCK
buttons for 2 seconds.
ii) Release both the LOCK and UNLOCK
buttons for 1 second.
iii) Press the UNLOCK button. The
answerback function informs you that the
ID code registration of the transmitter is
completed.

5-10 Features and controls

Keyless entry system (if so equipped)

5

NOTE

NOTE

CAUTION

5. To register the ID codes of additional
remote control transmitters, repeat step 4
within 60 seconds after step 4.

6. If no ID code of a remote control trans­mitter is registered within 60 seconds
after step 4, the registration mode is can­celed and the normal mode returns.

 For verification purposes, try to lock and

unlock the doors after the registration is
completed.

 The indicator light (4) comes on each time a

button is pressed.

 The keyless entry system does not work if

the key is in the ignition switch.

 The remote control transmitter can be used

from approximately 40 feet (12 m) away.
However, this distance may change if your
vehicle is near a TV transmitting tower, a
power station, or a radio station.

 If the UNLOCK button (2) is pressed when

all doors and the liftgate are locked and no
doors or the liftgate are opened within
approximately 30 seconds, the doors and the
liftgate will automatically re-lock.
On a vehicle equipped with the Smartphone
Link Display Audio, the functions can be
adjusted on the screen. For details, refer to
the separate owner’s manual.

 If the following conditions are observed after

pressing the LOCK (1) or UNLOCK (2) but­ton on the remote control transmitter, the
battery in the remote control transmitter may
need to be replaced.

• The doors and the liftgate cannot be locked
or unlocked.

• The panic alarm cannot be operated.

• The indicator light (4) is dim or does not
come on.

 If you lose your remote control transmitter,

please contact an authorized Mitsubishi
Motors dealer for a replacement.

 If you wish to obtain an additional remote

control transmitter, please contact an autho­rized Mitsubishi Motors dealer. A maximum
of 8 remote control transmitters can be pro­grammed for your vehicle.

 To use the new remote control transmitters, it

is necessary to register the key with both the
electronic immobilizer and keyless entry sys­tem.
Also refer to “Electronic immobilizer (Anti­theft starting system): Customer key pro­gramming” on page 5-6.

General information

N00546101124

Your keyless entry system operates on a radio
frequency subject to Federal Communica­tions Commission (FCC) Rules (For vehicles
sold in U.S.A.) and Industry Canada Rules

(For vehicles sold in Canada). This device
complies with Part 15 of FCC Rules and
Industry Canada licence-exempt RSS stan­dard(s).
Operation is subject to the following two con­ditions.

 This device may not cause harmful inter-

ference.

 This device must accept any interference

received, including interference that may
cause undesired operation.

 Changes or modifications not expressly

approved by the manufacturer for compli­ance could void the user’s authority to oper­ate the equipment.

Procedure for replacing the
remote control transmitter bat­tery

N00544101205

1. Before replacing the battery, remove static
electricity from your body by touching a
metal grounded object.

Features and controls 5-11

Keyless entry system (if so equipped)

5

NOTE

NOTE

CAUTION

+ side

- side

Coin type bat­tery CR1620

2. Remove the screw (A) from the remote
control transmitter.

3. With the Mitsubishi mark facing you,
insert the cloth-cov-ered tip of a flat blade
screwdriver into the notch in the remote
control transmitter case and use it to open
the case.

 Be sure to perform the procedure with the

Mitsubishi mark facing you. If the Mitsubi­shi mark is not facing you when you open the
remote control transmitter case, the buttons
may come out.

 The Federal Communications Commission

(FCC) ID number, the Industry Canada (IC)
number and the model number (radio certifi­cation) are indicated in the illustrated posi­tion.

5. Install a new battery with the +side (B)
up.

6. Close the remote control transmitter case
firmly.

7. Attach the screw (A) removed in step 2.

8. Check the keyless entry system to see that
it works.

5-12 Features and controls

4. Remove the old battery.

 You may purchase a replacement battery at

an electric appliance store.

 An authorized Mitsubishi Motors dealer can

replace the battery for you if you prefer.

 When the remote control transmitter case is

opened, be careful to keep water, dust, etc.
out. Also, do not touch the internal compo­nents.

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)

5

WAR N ING

WAR N ING

NOTE

Free-hand Advanced Secu­rity Transmitter (F.A.S.T.­key) (if so equipped)

N00503101163

The Free-hand Advanced Security Transmit­ter (F.A.S.T.-key) enables the doors and the
liftgate to be locked and unlocked, the engine

 Individuals who use implantable pace-

makers or implantable cardiovascular­defibrillators should keep away from the
external and internal transmitters. The
electromagnetic waves used in the
F.A.S.T.-key may affect the operation of
implantable pacemakers and implantable
cardiovascular-defibrillators.

to be started and the operation mode to be
changed simply by carrying it.
The F.A.S.T.-key can also be used as the
remote control transmitter of the keyless
entry system.
Refer to “Free-hand Advanced Security
Transmitter (F.A.S.T.-key): Keyless entry
system” on page 5-30.

The F.A.S.T.-key must be carried by the
driver. The F.A.S.T.-key is required for
vehicle operations such as locking and
unlocking the doors and the liftgate,
starting the engine and changing the
operation mode. When leaving the vehi­cle, make sure you are carrying the
F.A.S.T.-key and then lock the vehicle.

A- External transmitter
B- Internal transmitter

 Individuals using other electro-medical

apparatus besides implantable pacemak­ers and implantable cardiovascular-defi­brillators should check with the
manufacturer of the apparatus to confirm
the effect of the electromagnetic waves
used by the F.A.S.T.-key. The electromag­netic waves may affect the operations of
the electro-medical apparatus.

The operations possible with the F.A.S.T.­key can be modified as stated below.
(Keyless entry operations are possible.)
For details, contact an authorized Mitsubi­shi Motors dealer.

• Enabling only the locking and unlocking
of the doors and the liftgate

• Enabling only the starting of the engine

• Deactivating the F.A.S.T.-key

 The F.A.S.T.-key uses weak electromagnetic

waves.
In cases such as the following, operation
may be improper or unstable.

• The vehicle is near a facility that emits
strong electromagnetic waves, such as a TV
transmitting tower, a power station, a radio
station or an airport

Features and controls 5-13

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)

5

NOTE

NOTE

NOTE

• The key is carried together with other com­munication devices such as cellular phones
or radios, or electrical appliances such as
computers

• The F.A.S.T.-key touches or is covered by a
metal object

• A keyless entry system is being used
nearby

• The battery of the F.A.S.T.-key is run down

• The vehicle is in a location with strong
electromagnetic waves or noise

Use the emergency key in such circum­stances.
Refer to “To operate without using the
F.A.S.T.-key” on page 5-28.

 The F.A.S.T.-key is constantly performing

reception operations in its communication
with the vehicle. This means that the battery
is always running down, regardless of how
often the F.A.S.T.-key is used. The battery
life is about 1 to 3 years, depending on the
usage conditions.

 Since the F.A.S.T.-key is constantly perform-

ing reception operations, the reception of
strong electromagnetic waves can accelerate
the running down of the battery. Do not place
near to electrical appliances such as televi­sions or computers.

Operating range of the
F.A .S .T. -k ey

N00503201177

When a person enters the operating range of
the F.A.S.T.-key while carrying the F.A.S.T.­key and presses the driver’s or front passen­ger’s door lock/unlock switch, the liftgate
LOCK switch or the liftgate OPEN switch,
verification of the ID code is performed.
The doors and the liftgate can be locked and
unlocked and the engine can be started only
when the ID codes of the vehicle and
F.A.S.T.-key match.

 When the battery of the F.A.S.T.-key has run

down or there are strong electromagnetic
waves or noise in the area, the operating
range could decrease or operations could
become unstable.

Operating range for locking and
unlocking the doors and the lift­gate

The operating range is within about 2.3 feet
(70 cm) of the handles of the driver’s door,
front passenger door and liftgate.

*: Front of the vehicle

Operating range

:

 The door or liftgate switch can only be used

for locking or unlocking when a matching
F.A.S.T.-key is detected.

 The system may not operate if the F.A.S.T.-

key is too close to the windshield, door win­dows or liftgate.

5-14 Features and controls

5

 Even if the F.A.S.T.-key is within about 2.3

NOTE

NOTE

Driver’s and front passenger’s door lock/unlock
switches

feet (70 cm) of the handle of the driver’s
door, front passenger’s door or liftgate, the
system may not operate if the key is close to
the ground or in a high position.

 If the F.A.S.T.-key is within the operating

range, even a person not carrying the
F.A.S.T.-key can lock and unlock the doors
or the liftgate by pressing the driver’s or
front passenger’s door lock/unlock switch,
the liftgate LOCK switch or the liftgate
OPEN switch.

Operating range for starting the
engine and changing the opera­tion mode

The operating range is the interior of the
vehicle.

N00503301077

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)

*: Front of the vehicle

Operating range

:

 Even if the F.A.S.T.-key is within the operat-

ing range, it may not be possible to start the
engine and change the operation mode if the
key is in a storage space such as the glove
compartment, on top of the instrument panel,
or in the door pocket or luggage compart­ment.

 Even if the F.A.S.T.-key is inside the vehicle,

it may not be possible to start the engine and
change the operation mode if the key is too
close to a door or door window.

To operate using the F.A.S.T.­key

N00503401326

To l o ck

While carrying the F.A.S.T.-key, press the
driver’s or front passenger’s door lock/unlock
switch (A), or the liftgate LOCK switch (B)
within the operating range to lock all the
doors and the liftgate.
The turn signal lights will blink once and the
buzzer will sound once.

Also refer to “Doors locks”, “Power door
locks”, “Liftgate” and “Power liftgate” on
pages 5-34, 5-36, 5-38 and 5-39 respectively.

Features and controls 5-15

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)

5

NOTE

Liftgate switches

NOTE

NOTE

Driver’s door lock/unlock switch

 The time within which locking confirmation

is possible can be adjusted. See an autho­rized Mitsubishi Motors dealer for details.
On a vehicle equipped with the Smartphone
Link Display Audio, the function can be
adjusted on the screen. For details, refer to
the separate owner’s manual.

To u n lo ck

 On the vehicles equipped with the mirror

retractor switch, the outside rearview mirrors
automatically retract when all doors and lift­gate are locked using the driver’s or front
passenger’s door lock/unlock switch (A) or
the lift gate lock switch (B).

 In cases such as the following, the F.A.S.T.-

key does not operate.

• There is a F.A.S.T.-key in the passenger
compartment

• A door or the liftgate is open or ajar

• The operation mode is not in OFF.

 The liftgate OPEN switch (C) can be used to

confirm that the vehicle is locked properly.
Press the liftgate OPEN switch within
approximately 3 seconds of locking.

 If the liftgate OPEN switch is pressed 3 sec-

onds or more after the vehicle is locked, the
doors and the liftgate are unlocked.

5-16 Features and controls

While carrying the F.A.S.T.-key within the
operating range, you can unlock the doors
and the liftgate by using the F.A.S.T.-key
operation.
The dome light will turn on for 30 seconds.
The turn signal lights will blink twice and the
buzzer will sound twice.

Also refer to “Door locks”, “Power door
locks”, “Liftgate” and “Power liftgate” on
pages 5-34, 5-36, 5-38 and 5-39 respectively.

Press the driver’s door lock/unlock switch
(A) to unlock only the driver’s door.
Within approximately 2 seconds, press the
driver’s door lock/unlock switch one more
time to unlock all the doors and the liftgate.

 On the vehicles equipped with the mirror

retractor switch, the outside rearview mirrors
automatically extend when the driver’s door
is unlocked using the driver’s lock/unlock
switch (A), front passenger’s door
lock/unlock switch (B) or the liftgate open
switch (C).

 Settings can be changed so that all doors and

the liftgate are unlocked automatically by
pressing the driver’s door lock/unlock switch
once.
Refer to “Setting of door and liftgate unlock
function” on page 5-32.

Press the front passenger’s door lock/unlock
switch (B) or the liftgate OPEN switch (C) to
unlock all the doors and the liftgate.

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)

5

NOTE

Front passenger’s door lock/unlock switch
Liftgate OPEN switch

NOTE

NOTE

 If the doors and the liftgate are unlocked

using the driver’s or front passenger’s door
lock/unlock switch when all doors and the
liftgate are locked and no doors or the lift­gate are opened within approximately 30
seconds, the doors and the liftgate will auto­matically re-lock.

 The amount of time after unlocking until the

vehicle re-locks automatically can be
adjusted. See an authorized Mitsubishi
Motors dealer for details.
On a vehicle equipped with the Smartphone
Link Display Audio, the functions can be
adjusted on the screen. For details, refer to
the separate owner’s manual.

 In cases such as the following, the F.A.S.T.-

key does not operate.

• A door or the liftgate is open or ajar

• The operation mode is not in OFF.

 The doors and the liftgate cannot be

unlocked by using the liftgate OPEN switch
for approximately 3 seconds after locking.

 The time within which locking confirmation

is possible can be adjusted. See an autho­rized Mitsubishi Motors dealer for details.
On a vehicle equipped with the Smartphone
Link Display Audio, the function can be
adjusted on the screen. For details, refer to
the separate owner’s manual.

 Functions settings can be modified as stated

below.
See an authorized Mitsubishi Motors dealer
for details.
On a vehicle equipped with the Smartphone
Link Display Audio, the functions can be
modified on the screen. For details, refer to
the separate owner’s manual.

• Activating the operation confirmation func­tion (blinking of the turn signal lights) only
during locking, or only during unlocking.

• Deactivating the operation confirmation
function (blinking of the turn signal lights)
and buzzer.

• Modifying the number of blinks in the
operation confirmation function (blinking
of the turn signal lights).

• Making the buzzer sound when the
F.A.S.T.-key is removed from the passenger
compartment when all the doors and the
liftgate are closed.

Operation of the outside rear­view mirrors (Vehicles
equipped with the mirror
retractor switch)

N00585700056

To re tr a ct

Within 30 seconds of locking the doors and
liftgate using the LOCK switch, press the
LOCK switch twice rapidly to retract the out­side rearview mirrors.

To e x te nd

Within 30 seconds of unlocking the doors and
liftgate using the UNLOCK switch, press the
UNLOCK switch twice rapidly to return the

Features and controls 5-17

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)

5

NOTE

CAUTION

outside rearview mirrors to their extended
positions.

Electronic immobilizer (Anti­theft starting system)

The outside rearview mirrors are not initially
set to work as described above. If you want
them to work as described above, you need to
set them so that they do not retract/extend
when the doors and liftgate are
locked/unlocked using the F.A.S.T.-key or the
keyless entry system of the F.A.S.T.-key.
For details, please consult an authorized Mit­subishi Motors dealer.
On vehicles equipped with the Smartphone
Link Display Audio, it is possible to change
the setting by means of screen operations.
Refer to the separate owner’s manual for
details.

 On vehicles with F.A.S.T.-key and equipped

with the mirror retractor switch, the outside
rearview mirrors automatically retract when
all the doors and liftgate are locked using the
F.A.S.T.-key function.
Refer to “Features and controls: Outside
rearview mirrors” on page 5-60.

The electronic immobilizer is designed to sig­nificantly reduce the possibility of vehicle
theft. The purpose of the system is to immo­bilize the vehicle if an invalid start is
attempted. A valid start attempt can only be
achieved (subject to certain conditions) using
a F.A.S.T.-Key “registered” to the immobi­lizer system.
All of the keys provided with your new vehi­cle have been programmed to the vehicle’s
electronics.

N00529600114

Engine switch

N00513501115

To prevent vehicle theft, no F.A.S.T.-keys
other than those registered in advance can be
used to start the engine. (Electronic immobi­lizer function)
While carrying the F.A.S.T.-key, the engine
switch can be used to start the engine.

 The indicator light (A) will flash orange

when there is a problem or malfunction in
Free-hand Advanced Security Transmitter.
Never drive if the indicator light on the
engine switch is flashing orange. Immedi­ately contact your authorized Mitsubishi
Motors dealer.

5-18 Features and controls

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)

5

NOTE

CAUTION

NOTE

CAUTION

The indicator light on the engine switch illu-

 If the engine switch operation is not smooth

and feels like it is sticking, do not operate the
switch.
Immediately contact an authorized Mitsubi­shi Motors dealer.

 When operating the engine switch, press the

switch all the way in. If the switch is not
fully pressed, the engine may not start or the
operation mode may not change. If the
engine switch is pressed correctly, there is no
need to hold the engine switch down.

Operation mode of the engine
switch and its function

 OFF

The indicator light on the engine switch turns
off.
The operation mode cannot be put in OFF
when the selector lever is in any position
other than the “P” (PARK) position.

 ACC

Allows operation of electrical accessories.

minates orange.

 ON

All electrical accessories can be used.
The indicator light on the engine switch illu­minates green.
The indicator light goes off when the engine
is running.

 Your vehicle is equipped with an electronic

immobilizer. To start the engine, the ID code
which the F.A.S.T.-key sends must match the
one registered to the immobilizer computer.
(Refer to “Electronic immobilizer (Anti-theft
starting system)” on page 5-18)

Changing the operation mode

N00568001035

If you press the engine switch without press­ing the brake pedal while the vehicle is sta­tionary, you can change the operation mode
in the order of OFF, ACC, ON, OFF.

 When the engine is not running, put the oper-

ation mode in OFF. Leaving the operation
mode in ON or ACC for a long time when
the engine is not running may cause the bat­tery to be discharged, making it impossible
to start the engine.

 When the battery is disconnected, the current

operation mode is memorized. After recon­necting the battery, the memorized mode is
selected automatically. Before disconnect­ing the battery for repair or replacement,
make sure to put the operation mode in OFF.
Be careful if you are not sure which opera­tion mode the vehicle is in when the battery
is run down.

 The operation mode cannot be changed from

OFF to ACC or ON if the F.A.S.T.-key is not
detected to be in the vehicle. Refer to “Oper­ating range for starting the engine and
changing the operation mode” on page 5-15.

Features and controls 5-19