Mitsubishi DIAMOND DIGITAL DV260 User Manual

DV260

Wide Screen LCD Flat

Panel Display

26” (66cm) LCD Panel Size

User Manual

ENGLISH

Color LCD TV

USER'S MANUAL

Thank you for purchasing the LCD TV.

Before using your TV, please read the "SAFETY INSTRUCTIONS"

and this "USER'S MANUAL" carefully to learn how to operate the

TV properly. Keep this manual in a safe place. You will find it useful

in the future.

Notes on lnstallation

This product is marketed with the assumption that it is to be

installed by qualified personnel with relevant skills and competence.

It is recommended to consult with an installation specialist or your

dealer install and set up the product. We cannot assume liabilities

for damages caused by improper installation or mounting, misuse,
modifications or natural disasters.

1

SAFETY POINTS THAT YOU SHOULD KNOW ABOUT YOUR LCD TV

Our reputation has been built on the quality, performance, and ease of service of LCD TV.

Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which

will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your LCD TV.

IMPORTANT SAFETY INSTRUCTIONS

Follow all warnings and instructions marked on this TV.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DO NOT REMOVE THE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

TO AVOID FIRE OR ELECTROCUTION, DO NOT EXPOSE THIS MONITOR TO RAIN OR MOISTURE.

WARNING:

THE MONITOR SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND OBJECTS SUCH AS VASES

FILLED WITH LIQUIDS, SHOULD NOT BE PLACED ON THE TV.

NOTE:

There are no user serviceable parts inside the TV.
Model information and serial numbers are indicated on the rear side of the TV.

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle, is intended to

alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying

the appliance.

CAUTION:

MODIFICATIONS:

Adjust only those controls that are covered in these instructions, as improper changes or modifications not expressly
approved by us could void the user's authority to operate the TV.

The FCC requires that the user be notified that any changes or modifications made to this device, that are not expressly
approved by us may void the user's authority to operate the equipment.

POWER SOURCE

THIS TV IS DESIGNED TO OPERATE ON 120 VOLT 60Hz, AC CURRENT. INSERT THE POWER CORD INTO A 120 VOLT 60Hz
OUTLET.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TV　 (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR
OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED. THIS IS TO PREVENT BLADE

EXPOSURE. NEVER CONNECT THE TV TO DIRECT CURRENT OR ANYTHING OTHER THAN THE SPECIFIED VOLTAGE.

CAUTION:

Never remove the back cover of the TV as this can expose you to very high voltages and other hazards. If the TV
does not operate properly, unplug the TV and call your authorized dealer or service center.

2

(

)

Read before operating the appliance

Follow all warnings and instructions marked on this TV.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding- type

plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at

plugs, convenience receptacles, and at the point where they exit from

the apparatus.

11. Only use the attachments/accessories specified by the manufacturer.

12

13. Unplug this apparatus during lightning storms or when unused for long

periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required

when the appliance has been damaged in any way, such as when a

power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been dropped.

15. Warning-To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture.

16. Apparatus shall not be exposed to dripping or splashing and no objects

filled with liquids, shall not be placed on the apparatus.

17. The apparatus is entertainment use only and visual display takes are

excluded.

Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart/appliance combination to avoid injury

from tip-over.

IMPORTANT SAFETY INSTRUCTIONS

18. The Shock Hazard Marking and Associated Graphical Symbol is

provided on the bottom panel of the unit.

19. This apparatus is designed to comply with the recommended safety

standards for tilt and stability.

Do not pull the cabinet with excessive force. Doing so can cause the

product to overturn, resulting in damage to the product and/or

personal injury.

20. Follow instructions for wall, shelf, or ceiling mounting as

recommended by the manufacturer.

21. An outdoor antenna should not be located in the vicinity of overhead

power lines or other electrical circuits.

22. If an outdoor antenna is connected to the receiver, ensure that the

antenna is grounded to provide some protection against voltage

surges and built up static charges. Section 810 of the National

Electric Code, ANSI/NFPA No. 70-1984, provides information with

respect to proper grounding for the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit, size of

grounding connectors, location of antenna-discharge unit,

connection to grounding electrodes and requirements for the

grounding electrode.

ANTENNA

LEAD IN

WIRE

GROUND CLAMP

ELECTRIC

SERVICE

EQUIPMENT

NEC NATIONAL ELECTRICAL CODE

Note to the CATV system installer: This reminder is intended to point the

CATV system installer to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies that the

cable’s ground wire shall be connected to the grounding system of the

building, as close to the point of cable entry as possible.

ANTENNA

DISCHARGE UNIT

NEC SECTION 810-20

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUNDING CONDUCTORS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250 PART H)

ENGLISH

Do not place any objects on top of the TV. They may fall or cause
a child to climb up to retrieve the objects.

pertaining to your resident state. For disposal or recycling
information, please contact your local authorities or the
Electronic Industries Alliance: www.eiae.org.

Disposal of this product may require specific instructions

CAUTION: PREVENTION OF SCREEN BURN IN

Continuous on-screen displays such as video games, stock market quotations, computer generated graphics and
other fixed (non-moving) patterns can cause permanent damage to the TV. Such “SCREEN BURN IN” constitute
misuse and are NOT COVERED by our Factory Warranty.

PUBLIC VIEWING OF COPYRIGHTED MATERIAL

Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require prior
authorization from the broadcaster or owner of the video program material.

3

Important

Please read this User's Manual thoroughly, especially the Important Safety
Instructions on Pages 2 to 3 and 6 to 10. Misuse may cause damage to your
LCD TV and could shorten its lifespan, or may even cause injury to yourself.
Should you encounter any difficulty in the set-up or operation of your TV,
refer to the Troubleshooting guide at the back of this manual.
In the unlikely event that there is a problem with your LCD TV, switch off the
power and unplug the TV, and contact your dealer immediately.

CAUTION

Under no circumstances should you remove the back cover of your LCD TV.
Never guess or take any chances with electrical equipment of any kind - it is
better to be safe than sorry!

Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner,
powder soap, Electronic equipment cleaner, car wax, glass cleaner, etc.
especially because they would cause discoloration, scratches or cracks.

FEATURE

Enhanced definition LCD panel

The 26-inch color LCD display panel, with a resolution of 1366 (H) x 768 (V)
pixels, creates a widescreen picture. This panel features a thin form factor
and can be hung on a wall with an optional wall mounting kit.

High Performance Digital Processor

This panel displays a wide range of personal computer signals from 640 x
350, 640 x 400 VGA to 1360 x 768 .(RGB Analog input)

Software Notice

It is prohibited for the end user of this product to copy, reverse engineer or
reverse compile the software included therein, to the extent permitted by law.

LCD TV

After the LCD TV has been on for any length of time, you will notice that the
screen becomes warm. Please note that this is normal.

To prevent scratches or damages to the LCD screen, do not knock or rub the
surface with sharp or hard objects. Clean the screen with a soft cloth
moistened with warm water and dry with a soft cloth. A mild soap may be
used if the screen is extremely dirty. Do not use harsh or abrasive cleaners!

CAUTION

Use a soft cloth to clean the cabinet and the control panel of the TV. When
excessively soiled, dilute a neutral detergent in water, wet and wring out the
soft cloth, then wipe the TV and afterwards wipe it off with a dry soft cloth.

Easy-to-use remote control and on
screen display system

The included remote control operates all TV functions. Further, the on­screen display system, shows the status of the control settings in an easy-to­view fashion.

Power saving system

The International ENERGY STAR® power saver feature saves power
consumption automatically when input signals are not available.
When connected to a VESA DPMS-compliant PC, the monitor cuts its power
consumption while it is idle.

4

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS.........................2

SAFETY INSTRUCTIONS ...............................................6

INSTALLATION INSTRUCTIONS .................................10

Desk Top Stand ..........................................................10

Anti-Tipping Prevention...............................................10

Power Cord Connection..............................................11

Connecting Antenna / Cable TV Signal ......................12

Connecting to Video Components ..............................13

Connecting to a PC.....................................................14

COMPONENT NAMES ..................................................15

Main Unit ...................................................................15

ATTENTION................................................................16

Remote Control (continued)......................................17

OPERATING INSTRUCTIONS ......................................18

Turning Power Off.......................................................18

Selecting AV Inputs.....................................................19

Volume Adjustment..................................................... 19

Audio Mute.................................................................. 19

Using the Menu Screen (On-screen display system) 20

Image Settings............................................................ 21

Display Settings ..........................................................22

Advanced PC.............................................................. 23

Audio Settings............................................................. 23

Setup ..........................................................................24

Channel Setting .......................................................... 25

ASPECT .....................................................................29

Teletext Menu .............................................................30

TROUBLESHOOTING................................................... 31

Symptoms................................................................... 31

Abnormal Displays Corrections VGA Only ................. 34

PRODUCT SPECIFICATIONS ...................................... 35

Component Connection.............................................. 36

Recommended Signal List.......................................... 36

ENGLISH

Notes about this manual

The information in this manual is subject to change without notice.
While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us should you have any comments, views or

questions about our product.

Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, when using the product. We are not held

liable for damages caused by improper handling of the product.
Reproduction of this manual in whole or in part without our prior written permission is prohibited.
The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.

5

SAFETY INSTRUCTIONS

This LCD TV has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if you are to
obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions

About the Symbols

Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the users and to prevent
property damage. The meaning of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the
contents.

WARNING

CAUTION

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect

handling.

This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due to

incorrect handling.

Typical Symbols

This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.

This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or adjacent to the symbol (the symbol to the left

indicates that disassembly is prohibited).

This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or adjacent to the symbol. (the symbol to the left

indicates that the power plug should be disconnected from the power outlet).

WARNING

Never use the TV if a problem should occur.

Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables, penetration
of liquids, or foreign matter, can cause a fire or electrical shock.

In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the

smoke or odor has cleared, contact your dealer. Never attempt to make repairs yourself because this could be dangerous.

Do not insert foreign objects or pour liquids inside the TV.

Penetration of liquids or foreign objects could result in a fire or electrical shock. Use special caution in households where children are
present.
If liquids or foreign objects should enter the projector, immediately turn off the power switch, disconnect the power plug from the power
outlet and contact your dealer.

Do not place the TV in a bathroom.
Do not expose the TV to rain or moisture.
Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc. on or around the TV.
Do not place metals, combustibles, etc. on or around the TV.

Never disassemble or modify the TV.

The TV contains high voltage components. Modification could result in a fire or electrical shock.
Never remove any cover.

Do not subject the TV to shock or impact.

If the TV is subject to shock and/or is broken, it could result in an injury, and continued use in such a state could result in fire or electrical
shock. If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet and
contact your dealer.

Do not place the TV on an unstable surface.

If the TV should be dropped and/or broken, it could result in an injury, and continued use in such a state could result in fire or electrical
shock. Do not place the TV on an unstable, slanting or vibrant surface such as a wobbly or inclined stand.

Do not obstruct the ventilation of the TV.

If ventilation is obstructed during the operation of the TV or just after switching off the power, it could result in damage and shorten the
lifespan of your TV due to overheating. Make sure there is ample ventilation.

Keep a space of 100mm (10cm) or more between the sides, rear and top of the TV and other objects such as walls.
Do not place anything around ventilation openings of the TV.
Never block ventilation openings.
Do not put the LCD screen side up.
Do not cover the TV with a tablecloth, etc.
Do not place the TV on a carpet or bedding, or near a curtain.

Use only the correct power outlet.

Incorrect power supply could result in fire or electrical shock. Use the correct power outlet depending on the indication on the TV and the
safety standard.
The enclosed power cord must be used depending on the power outlet to be used.

Disconnect the plug

from the power

outlet.

Do not disassemble.

6

SAFETY INSTRUCTIONS (continued)

WARNING

Be cautious of the power cord connection.

Incorrect connection of the power cord could result in fire or electrical shock.
Do not touch the power cord with a wet hand.
Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.
Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead, obtain an

Be sure to ground the connection properly.

Connect the ground terminal of the AC inlet of this TV with the ground terminal provided at the power outlet using the enclosed power cord.

Be careful when handling the power cord and external connection cables.

Do not use damaged power cords or cables as they can cause a fire or electrical shock. Do not apply excessive heat, pressure or tension
to the power cord and cables.
If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
Do not place the TV or other heavy objects on the power cord and cables. Also, do not place a spread, cover, etc., over them as this could

Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug

Do not place the power cord near a heater.
Do not touch the power plug just after disconnecting it from the power outlet. The static discharge can cause an electric shock.
Do not touch the power plug during a lightning storm.
Avoid coiling the power cord and bending it sharply.
Protect the power cord from being walked on or pinched at particularly at plugs, conveniences receptacles, and at the point where they exit

Do not modify the power cord.

Be careful when handling the batteries of the remote control.

Incorrect handling of the batteries could result in a fire or personal injury. The batteries may explode if not handled properly.
Keep the batteries away from children and pets. If swallowed, consult a physician immediately for emergency treatment.
Do not allow the batteries to be exposed to fire or water.
Avoid fire or high-temperature environments.
Do not hold the batteries with metallic tweezers.
Keep the batteries in a dark, cool and dry place.
Do not short circuit the batteries.
Do not recharge, disassemble or solder the batteries.
Do not physically impact the batteries.
Use only the batteries specified in the manual accompanying this TV.
Make sure the plus and minus terminals are correctly aligned when inserting the batteries.
If you observe a leakage of the batteries, wipe out the liquid and then replace the batteries. If you spill the liquid on your body or clothes,

Obey the local laws when disposing the batteries.

appropriate extension lead or consult your dealer.

If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.

result in the inadvertent placing of heavy objects on the concealed power cord or cables.

or connector.

from the panel.

rinse well with water.

Surely connect the

ground wire.

ENGLISH

7

SAFETY INSTRUCTIONS (continued)

CAUTION

Be careful in moving the TV.

Neglect could result in an injury or damage.
Do not move the TV during use. Before moving, disconnect the power plug and all external connections.
Get the help of another person if you find it difficult to move the TV alone.
Avoid any impact or shock to the TV; in particular take care of the glass screen.

Do not put anything on top of the TV.

Placing anything on top of the TV could result in loss of balance or falling, and can cause an injury or damage. Take special care in
households where children are present.

Avoid a humid or dusty place.

Placing the TV in a smoke filled, or in a highly humid, dusty place with oily soot or corrosive gas could result in fire or electrical shock.
Do not place the TV near the kitchen, a humidifier or any other place where there is oil, smoke or humidity.

Avoid a high temperature environment.

The heat could have adverse influence on the TV and its components, and could result in transformation, melting or fire.
Do not place the TV, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
Do not put the TV in a place where the temperature varies rapidly.

Remove the power cord when not using the TV for a long time.

For safety, disconnect the power cord if the TV is not to be used for prolonged periods of time.
Before cleaning, turn off and unplug the TV. Neglect to do so could result in a fire or electrical shock.

Disconnect the plug

from the power

outlet.

PRECAUTIONS

Installation environment

Do not obstruct the ventilation slots.
Do not place the TV on a carpet or blanket, or near a curtain or anywhere else where there is a possibility of obstructing the ventilation slots of the TV.
Do not place the TV in the following places.

Hot places such as near heaters, or in places exposed to the direct rays of the sun.
Places where the temperature varies rapidly.
Places with soot, dust or high humidity.
Places with poor ventilation.
Places such as near a fire.
Wet places such as bathrooms, or shower rooms.
Places where you can trip over the TV.
On objects that vibrate.
On objects that are unstable.

How to view the TV

If you use the TV in too dark a room, your eyes may become tired.
Use it in a reasonably bright room.
Avoid direct rays of the sun on the screen to prevent eye fatigue.
Your eyes will get tired after viewing the TV for long periods of time.
Relax your eyes by looking away from the TV from time to time.
Please watch the TV in downward direction.

How to clean the LCD screen panel of the TV

Before cleaning the TV, turn off the TV and disconnect the power plug from the power outlet.
To prevent scratching or damaging the LCD screen, do not knock or rub the surface with sharp or hard objects. Clean the screen with a soft cloth moistened
with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or abrasive cleaners.

How to clean the cabinet of the TV

Use a soft cloth to clean the cabinet and control panel of the TV. When excessively soiled, dilute a neutral detergent in water, wet and wring out the soft cloth,
wipe the TV and afterwards wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. as they could cause
discoloration, scratches or cracks.

8

SAFETY INSTRUCTIONS (continued)

Prevention of an obstacle to Radio receivers

This TV has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.

Keep the TV away from Radio.
Adjust Radio antennas in order for the TV not to receive interference.
The antenna cable of Radio should be kept away from the TV.

Use a coaxial cable for antenna.
You can check if this TV influences Radio receivers by turning off all other equipment other than the TV.
If you find a problem receiving Radio when using the TV, check the instructions mentioned above.

Precautions for the cable connection

Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are properly made and in

accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing connections.

Confirm the connector is fixed tightly when the signal cable is connected.

Also confirm the screws on the connector are tightened.
Plug the power cord of the TV into a different socket from that for other equipment, such as Radio etc.
Use a plug with ground terminal and make sure that it connects to the ground.

Precaution during transportation

Please pay attention when you transport this TV because it is heavy.
Furthermore, use the original carton box and its packaging materials when the TV is transported.
Failure to transport the TV in any carton except the original carton may result in damage to the TV.
Save the original carton box and all packing material.

Do not physically impact the remote control.

A physical impact could cause damage or malfunction of the remote control.
Take care not to drop the remote control.
Do not place heavy objects on the remote control.

Avoid strong rays.

Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.

Avoid radio interference.

Any interfering radiation could cause distorted images or noises.
Avoid radio generator such as a mobile telephone, transceiver, etc. around the TV.

Set the sound volume at a suitable level.

It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.

Precautions for the installation

Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved stand or legs with the

fixings provided according to the instructions.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip-over.
This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the

cabinet that could cause the product to overturn resulting in product damage and/or personal injury.
Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
Only use the attachments/accessories specified by the manufacturer.
Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.

Other precautions

Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a stand-by mode.

Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or handicapped people.
Disposal of this product may require specific instructions pertaining to your resident region.
Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!

ENGLISH

9

INSTALLATION INSTRUCTIONS

Desk Top Stand

TV

Desktop stand

WARNING

Use one of the special mounting units to install this product. A mounting unit of insufficient strength or inadequate design can cause overturning or dropping

and result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries or property damage
caused by use of other mounting units or improper installation.

CAUTION

Do not attempt installation of the wall mounting unit and ceiling mounting unit by yourself as it can be dangerous. Ask

your dealer to provide the name of a qualified technician.

In order to prevent overheating, maintain a space of 10cm (4 inches: For a desktop setup) or more between the sides of

the TV and other objects such as walls, etc., so that the ventilation holes are not blocked.

Anti-Tipping Prevention

CAUTION

Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar.

Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.

10cm (4 inches) or more*

Clamp

Clamp

Cord

or

chain

10

Hook

Chain

Cord or chain

Wall or Pillar

Clamp

INSTALLATION INSTRUCTIONS (continued)

Power Cord Connection

Connect the power cord, after completing all other connections.

ENGLISH

1. Connect the power cord to the rear of the TV.

2. Connect the power cord plug to the power outlet.

3. Turn ON the

main power switch is located on the side

(The type of plug is different from this drawing for some countries.)

CAUTION

Use only the power cord provided.

Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.

11

INSTALLATION INSTRUCTIONS (continued)

Connecting Antenna / Cable TV Signal

Make sure that the power switch of the TV is turned off.

1. TV IN connector (Analog) Connect an antenna or a cable TV box using the coaxial cable

2. HDMI IN connector Connect devices such as a DVD player or set-top box

3.PC Audio connector for VGA Connect the audio cable from your computer

4.VGA connector Connect to the VGA cable from your computer to the TV

5. Component audio and video connectors (AV2 IN) Connect devices such as a DVD player, set-top box, or cable TV box

6. AV-out & Subwoofer audio out connectors AV-out connect devices such as a VCR, Subwoofer audio out connect an optional powered subwoofer to the TV.

7. Composite video, S-Video and audio connectors (AV1/AV3 IN) Connect devices such as a VCR or DVD player

8. Side I/O (AV3 IN) S-Video , composite and audio connectors Connect devices such as a video game system or a DVD player and turn on or turn off the

Main power switch the power of your appliance.

9. Power connector Connect your power cord

Precautions when connecting the antenna

Use a coaxial cable which is free from interference. Avoid using a parallel flat wire as interference may occur, causing the reception to become unstable and

noise to appear on the screen.
Avoid using an indoor antenna as this may be affected by interference and poor reception.
Keep the power cord as far away from the antenna wire as possible.

VHF(300-Ohm) antenna / UHF antenna

When using a 300-ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads to the screws of the VHF or UHF adapter. Plug the

300-ohm to 75-ohm adapter into the antenna terminal on the TV.

When both VHF and UHF antennas are combined

Attach an optional antenna cable signal combiner to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your local

electronics retailer.

12

A

INSTALLATION INSTRUCTIONS (continued)

Connecting to Video Components

1. Make sure that the power switch of the TV is turned off.

2. Make sure that the power switch of the Video component is turned off.

TV Quick Connecti on

U.S.

S-CABLE

Side I/O : AV3 (Option)

Earphone (Option)

ERIEL

CAMCORDER

DVD PLAYER

Cable/Satellite
Decoder Box

Better Connection

VCR

ANTENNA

[An example of connecting video components]

If the OUTPUT RCA terminal is connected to a 2nd monitor, it is possible to view the same image as on the main source. The composite video signal from

CVBS input will be displayed on both screens at the same time.

Applicable video signals for each input terminal

(See page 36, 37 for details)

Terminal RCA / 4Pin Mini Din HDMI D-Sub

Signal CVBS S-Video Component Video RGB

AV1

AV2

AV3: option

{ {

{

{ {

HDMI

VGA

({: Avaliable)

{

{

{

ENGLISH

13

INSTALLATION INSTRUCTIONS (continued)

Choose an appropriate site and install the product on a level table where the stand is secure.
Ensure that a power socket is readily accessible near the place where you install the TV.
Make sure that the power switch of this device is turned off.

Connecting to a PC

1. Make sure that the display signal of the personal computer to be used is compatible with the specifications of this device.

See "Product Specifications" concerning the specifications of this device.

2.Make sure that the power switch of the personal computer is turned off.

3.Connect the signal input terminal VGA on the rear panel of this device to the display signal output terminal of the personal

computer.

Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with the personal computer

may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the personal computer manufacturer or your
local retail dealer.

TV rear panel

Power cable
connector

3.5mm
Stereo

Audio

15 Pin D-sub
VGA
connector

Cable

To Audio

Output

Note

Please refer to the caution regarding prevention of screen burn in on page 3.

To Video
Output

Subwoofer Output provides a single un-amplified audio output that passes along the audio signal from the LCD TV.

Note: When using a Home Theater audio system with this LCD TV, please connect the sub woofer (if originally supplied with the audio

system) directly to the Home Theater components subwoofer terminal.

14

COMPONENT NAMES

Main Unit

Front

Panel

Cabinet
(Front Frame)

ENGLISH

These buttons are located on the top.

VOLUME buttons

( ADJUST buttons)

Control Panel

Press the television panel
power button.

MENU buttons

(function or return one step)

Indicator lamp

The main power switch is located at the back, on the
lower surface.

(26”)

SOURCE buttons

(mode selection)

ENTER button

(adjusting or next page)

CHANNEL buttons

( Adjust the TV Channel)

or power on

POWER button

Caution when moving the main unit

As this product is heavy, whenever it is moved, two people are required to transport it

safely.

Whenever the unit is moved it should be gripped on the top of the panel and the unit

should then be held at the base on both sides for stability as shown.

Main power source button.

Press the main power
source button.

Rear

External device connection terminals

15

A

COMPONENT NAMES (continued)

Remote Control

DISPLAY

MUTE

LED INDICATION

TV TUNER

NUMBER KEYPAD

PICTURE

ASEPCT

MENU

PROGRAM / ADJUST ()

SOURCE

PC

AV4 (option)

AV1

INDEX

TEXT

SUB

HOLD

POWER ON/OFF

CH () or power
on

VOLUME ()

SLEEP

RECALL

RETURN

SELECT ()

ENTER

I/II

AV3 (option)

HDMI

V2

MODE

REVEAL

CANCEL

SIZE

Installing the Batteries Handling the Remote Control

1. Open the battery cover.

Slide back and remove the battery cover in

the direction of the arrow.

2. Installing the batteries.

Install two included Size AAA batteries

observing the correct polarities(+,-).

3. Close the battery cover.

Replace the battery cover in the direction of

the arrow and snap it back into place.

CAUTION

Do not mix new and old batteries together. The batteries could explode or leak,

resulting in fires, physical injury, or stains.

When inserting batteries, observe their correct polarities as marked on the

product. If inserted in the wrong direction, the batteries could explode or leak,
resulting in fires, physical injury, or stains.

Use the remote control within about 16 feet from front of the unit’s remote­control sensor and within 30 degrees on both sides.

Within 30 degrees

About 10 feet

Within 30 degrees

About 10 feet

About 16 feet

ATTENTION

Do not drop the remote control.
To avoid possible failures, do not splash the remote control with water or

put it on a wet object.

If leaving the remote control out of use for an extended period of time,

remove the batteries from it.
If the remote control does not respond properly, replace the batteries.
Strong light such as direct sunlight exposed on the photoreceptor of the

remote control can cause operational failure. Position this unit to avoid

direct contact with such light.

16

COMPONENT NAMES (continued)

Remote Control (continued)

POWER

Press this button to turn the TV on or off.

MUTE AV4

Press this button to turn off the sound. Press it
once more or press the volume up button to 　
return the sound.

DISPLAY AV3

Press this button to show the input signal
information

TV AV2

Press this button to choose TV as the source.

CHANNEL (CH) AV1

TV select channels up or down or DC
power-on

VOLUME ( VOL) PC

Press these two buttons to adjust the
volume up or down

RECALL HDMI

TV switch to last channel program Switch to input source HDMI

SLEEP Teletext color Keys

Select timer to turn power off. The default
timer is 30, 60, 90 and 120 minutes (Only
enable in TV function).

0~9 Number Keys REVEAL

Used to select cable TV or Terrestrial
programs.

PICTURE MODE

Picture image scheme mode (Personal,
Sport, Game, Movie, Vivid)

ASPECT INDEX

Selcet how the picture is displayed on the screen;
pillar box, letter box expand, Panoramic, or Full
Screen modes

RETURN TEXT

Return to last level OSD menu Turn the Teletext function

MENU CANCEL

Turn on the OSD menu.

Adjust the selected item on menu. Teletext font size change

* Press to select desired item on the menu

* Press to select desired page on the text
mode

Enter key, confirm OSD select function Teletext SUB function

I/II

TV multi-language sound system select

SOURCE

OSD source selec input menu

Option, depen on model define.

Switch to input source Side I/O
AV3 composite or AV3 S-video.

Option, depen on model define.

Switch to input source AV2
Component YcbCr/YPbPr or
composite

Switch to input source AV1
composite or AV1 S-video

Switch to input source PC

Turn ON/OFF conceal
information.

For special teletext functions

Teletext Turn ON/OFF list mode.

Teletext Turn page to index

page.

ON/OFF

Press the CANCEL button again into
display the TELETEXT screen

SIZE

HOLD

Teletext hold funtion

SUB

ENGLISH

17

OPERATING INSTRUCTIONS

Power Lamp

1

Main power switch

2

SUB-POWER button

Turning Power Off

1. To turn the TV power OFF, press the power buttonor the
power button on the remote control.

Note: During normal use, the main power switch is set in the ON position.

Power lamp

Power

lamp

Dark Off

RED

GREEN On

AMBER

When the indicator lamp lights Amber or the message “No Signal

connected” or “Going to sleep” appears on the screen, there is

something abnormal about the status of the reception.

See Trouble Shooting.

CAUTION

Avoid repeatedly turning the TV on and off at short time intervals. Failures

might result from doing so.

Turn off the main power switch before leaving the TV out of use for an

extended period of time.

If a power failure occurs while the main unit is running, it would be powered

on upon recovery from the failure. Turn off the main power switch when a
power failure occurs.

(Power Save)

Power

Status

Off

(standby)

Off

When the main power switch is set to

OFF.

When the main power switch is ON, and

the OFF button on the remote control or

the SUB POWER button is OFF.

When the main power switch is ON, and

the Power or Channel up/down button on

the remote control or the Power or

Channel up/down button is ON.

When the main power switch is ON, and

the PC is in power save mode.

Operation

POWER OFF

18

OPERATING INSTRUCTIONS (continued)

Volume Adjustment

The volume can be adjusted by pressing the  and  buttons

of the remote control (or the <

the TV).

SOURCE button

VOLUME buttons

MUTE

TV

VOLUME
CONTRO

When the volume buttons are pressed, the volume adjustment

status guide will be displayed.

The volume will increase when the VOL+ (or ) button is pressed while

the guide is being displayed.

The volume will decrease when the VOL- (or

the guide is being displayed.

Audio Mute

The audio volume can be temporarily muted by pressing the
MUTE button of the remote control.

- and > + volume buttons of

Volume setting value

Adjustment status guide

15

) button is pressed while

ENGLISH

SELECT 

SOURCE

Selecting AV Inputs

Input can be switched by pressing the TV, AV 1,
AV 2, AV 3, HDMI, PC buttons
Input can be switched in the sequence TV AV 1

AV 2  AV 3 (OPTION)  HDMI  VGA by pressing the
SOURCE button and then select the Input with the select keys

 and then press the ENTER
station, press the TV button.

button.To select a TV

When the MUTE button is pressed, the above icon will appear.

The volume setting can be lowered by pressing the VOL- button while the

audio is muted.

Muting can be cancelled by pressing the VOL+ button or the MUTE button

while the audio is muted.

19

A

OPERATING INSTRUCTIONS (continued)

Using the Menu Screen
(On-screen display system)

When the MENU button is pressed, the adjustment menu screen

will appear. Adjustment and setting are possible by using the

SELECT buttons, PROGRAM ADJUST buttons and the ENTER

button.

Example: Selecting the Image Settings

1. Press the MENU button to display the Main Menu screen.

MENU button

PROGRAM/

DJUST 

buttons

POWER OFF

SELECT
buttons

ENTER button

2. Select the Image Settings screen with the  and  　

PROGRAM ADJUST buttons and press the ENTER

button.

Image Settings

Scheme

Brightness

Contrast

Saturation

Back Light

Color Temp.

Advanced

: select ENTER : action RETURN : back

Personal

Medium

Cool

3. Use the  and  SELECT buttons to select the item to be

adjusted and then use the  and  ADJUST buttons to

adjust (example: Brightness.)

Image Settings

Scheme

Brightness

Contrast

Saturation

Back Light

Color Temp.

Advanced

: : select ENTER : action RETURN : back

Personal

Medium

Cool

Press the MENU button to return to the previous screen.
If there is no operation for a period of one minute, the Adjustment Menu

screen will disappear.

20

OPERATING INSTRUCTIONS (continued)

Image Settings

Image Settings

Scheme

Brightness

Contrast

Saturation

Back Light

Color Temp.

Advanced

: select ENTER : action RETURN : back

Personal

Medium

Cool

1. Press the “MENU” button to display the Main Menu screen.

2. Press the ENTER button to confirm then use the  and  SELECT buttons to select the item to be adjusted and then use the

buttons to adjust the selected items.

Selected

characters

SCHEME

Brightness Black is subdued for increased

Contrast Narrows the gap between light

Saturation Decrease saturation level. Increase saturation level. Adjust as desired.

Back Light

Color Temp

Personal Vivid Movie Game Sport

overall darkness.

and dark.

 

Black is set to off for increased

overall brightness.

Broadens the gap between light

and dark.

High Medium Low

Cool Normal Warm User

Red
Green
Blue

Adjust as desired.

Adjust as desired.

Adjust for maximum visibility to suit the ambient brightness.

Adjust as desired.

Normally set to Normal.

Setup hint

ENGLISH

 and  ADJUST

Advanced

Tint Enhances red and weakens

green.

SHARPNESS Decrease sharpness level Increase sharpness level

FLESHTONE

Low Off High Moderate

Enhances green and weakens

red.

This cannot be adjusted when receiving the PAL/SECAM signal. and
will be greyed out.

Adjust as desired for photo realistic skin color.

Normally set to the center position; shift to the minus (-) side for a
softer picture and plus (+) for a sharper picture.

Set except Off for richer skin color.

OPERATING INSTRUCTIONS (continued)

Display Settings

Display Settings

Aspect Ratio

PIP Mode

PIP Position

: select ENTER : action RETURN : back

Selecting Source

While a black box appears on the screen, press SOURCE button menu appears.

Picture mode will change in the following sequence, each time the remote button is pressed.
Select the SOURCE by using the   select keys on the remote control. Then, press the

SOURCE

Full Screen

Off

Bottom-Right

ENTER button.

SOURCE

TV

AV 1 VID EO1

AV1 SVIDEO

AV 2 VID EO

AV2 Component

AV 3 VID EO3

AV3 SVIDEO

PC

HDMI

Or

TV

AV 1 VIDEO1

AV1 SVIDEO

AV 2 VIDEO

AV2 Component

PC

HDMI

Advanced PC

Selected

characters

AUTO Adjustment Press the ENTER button to action. Normally set to off mode. Adjust automatically for clock, phase, and

POSITION

PHASE

CLOCK Reduces the dot clock. Increases the dot clock. Adjust for maximum character clarity.

Press the PROGRAM button to adjust the display position

Slows the dot clock Phase

 

position.

Adjust the horizontal and vertical display positions.

Advances the dot clock Phase

Setup hint

Audio Settings

Audio Settings

Bass

Trebl e

Balance

Effect

Low

ENGLISH

: select ENTER : action RETURN : back

Selected

characters

Bass Decreases bass. Increases bass. Adjust as desired.

Treble Decreases treble. Increaes treble. Adjust as desired.

Balance Decreases right volume level. Increases left volume level. Adjust as desired.

 

Setup hint

OPERATING INSTRUCTIONS (continued)

Setup

Setup

Tuner/Channel

OSD Timeout

Sleep Timer

Reset Default

: select ENTER : action RETURN : back

Selected

characters

Tuner/Channel

OSD Timeout

Sleep Timer

Reset Default YES NO Resets all settings to FACTORY defaults.





Country Auto Scan Channel Edit

10 Sec 30 Sec Off 5 Sec

Off 30 Min 60 Min 90 Min 120 Min

Off

Off

No

Setup hint

Adjusts Tuner/Channel Settings.

Adjusts OSD display and on-screen time

Set the TV off time for each mode

* Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Manually adjust to optimize them.

* When operating the TV at first time, its TV system is at “default factory mode” and this mode cannot display the image normally on the screen.In order

to watch the TV program without problem, please refer to the page 28 to setup the TV system accordingly for normally display.

A

A

A

A

OPERATING INSTRUCTIONS (continued)

Channel Setting

*Note: The TV must be in TV mode for access to this Menu.
When operating the TV at first time, its TV system is at “default factory mode” and this mode cannot display the image normally on the screen. In order
to watch the TV program without problem, please refer to the follow steps to setup the TV system accordingly for normally display

1. Auto Scan: then execute Auto Scan when you select Country already

Setup

uto Scan

Channel Edit

: select ENTER : action RETURN : back

2.Channel Edit

Setup

uto Scan

Channel Edit

: select ENTER : action RETURN : back

uto Scan Option

uto B/G I D/K M

ENTER : action MENU : back / quit

Channel Edit

CH Nam e Fr equency TV Syst em

: select RED/GREEN/YELLOW/BLUE edit MENU:exit

Channel Scan : Auto

PAL B G

VHF-Low 72 MHz 3%

ENTER: break and save MENU: break and cancel

1

ENGLISH

Selected

characters

Auto Scan

Red : Channel Swap edit

Channel Edit

NOTE:

Connecting the antenna or cable. Please execute the System Frequency Scan first.

Green : Channel Name edit

Yellow : Channel Frequency edit

Blue Channel System edit

 

- -

Press “ENTER” will display the TV system options menu, select any mode
to auto scan TV channel. If select ”auto” mode option will auto detect TV
system, else will set TV system as option mode.

Press currect color button to edit channel.

Operating hint

A

1 Enter “Channel Edit” menu:

1.1 Press “Menu” key to enter OSD -> Select “Setup” page-> “Tuner/Channel”-> “Channel Edit”, you will see “Channel Edit” menu, it will
display the channels that the TV currently can show

Channel Edit

CH Name Frequency TV System

1 001. 55.25MHz NTSC M

Setup

uto Scan

Channel Edit

CH: 1

: select ENTER : action RETURN : back

2 Select channel: use “Up/Down” key to select channel
3 Edit channel Data: different Color keys can be used to edit channel’s info, details as below:

3.1 Red key: can swap between two channels, example: when the color bar is at CH1, press the “Red” key and then move the color bar to
CH3 and press again on the “Red” key, CH1 will swap with CH3

2 61.25MHz NTSC M

3 XYZ+ 67.25MHz NTSC M

4 77.25MHz NTSC M

5 83.25MHz NTSC M

6 91.25MHz NTSC M

7 97.25MHz NTSC M

8 97.25MHz --- ---

: select RED/GREEN/YELLOW/BULE MENU : exit

Channel Edit

CH Name Frequency TV System

1 001. 55.25MHz NTSC M

2 61.25MHz NTSC M

3 XYZ+ 67.25MHz NTSC M

4 77.25MHz NTSC M

5 83.25MHz NTSC M

6 91.25MHz NTSC M

7 97.25MHz NTSC M

8 97.25MHz --- ---

: select RED/GREEN/YELLOW/BULE MENU : exit

CH Name Frequency TV System

1 XYZ+ 55.25MHz NTSC M

2 61.25MHz NTSC M

3 001. 67.25MHz NTSC M

4 77.25MHz NTSC M

5 83.25MHz NTSC M

6 91.25MHz NTSC M

7 97.25MHz NTSC M

8 97.25MHz --- ---

: select RED/GREEN/YELLOW/BULE MENU : exit

3.2 Green key: to edit the channel name. After pressing the “Green” key, using the “Left/Right” key and move to the desired name position

Channel Edit

and use “Up/Down” key to select the characters you need

Channel Edit

CH Name Frequency TV System

1 001. 55.25MHz NTSC M

^

2 61.25MHz NTSC M

3 XYZ+ 67.25MHz NTSC M

4 77.25MHz NTSC M

5 83.25MHz NTSC M

6 91.25MHz NTSC M

7 97.25MHz NTSC M

8 97.25MHz --- ---

CH Name Frequency TV System

1 A01. 55.25MHz NTSC M

2 61.25MHz NTSC M

3 XYZ+ 67.25MHz NTSC M

4 77.25MHz NTSC M

5 83.25MHz NTSC M

6 91.25MHz NTSC M

7 97.25MHz NTSC M

8 97.25MHz --- ---

Channel Edit

^

: select RED/GREEN/YELLOW/BULE MENU : exit

: select RED/GREEN/YELLOW/BULE MENU : exit

3.3 Yellow key: for editing channel’s frequency. After pressing the “Yellow” key, it will show a frequency tuning window, use
“Up/Down/Left/Right” to tune to your required frequency

Frequency

Fine Tune

: select : sction MENU : exit

55.25MHz

3.4 Blue key: for editing the TV system. After pressing the “Blue” key, it will show a TV system edit window (containing Color and Sound
system), use “Up/Down/Left/Right” to change to your required Color and Sound system

Color System

NTSC M

: select Sound System

4 The Other functions:

4.1 Add: when you open the “Channel Edit” menu, you will see that at the end of the list will be a channel with “---“ as the sound system. This
is automatically added for user to edit new channel. You can move the color bar to there and edit the Sound system of that channel, once
you change the sound system to none “---“, the system will automatically add a new channel for user to edit, this will continue until the
maximum channel number supported is reached

Channel Edit

CH Name Frequency TV System

1 266.25MHz PAL B/G

2 175.25MHz PAL B/G

3 519.25MHz PAL B/G

4 855.25MHz PAL B/G

5 215.25MHz PAL 1

6 639.25MHz PAL 1

7 77.25MHz PAL D/K

8 55.25MHz NTSC M

9 55.25MHz --- ---

CH Name Frequency TV System

1 266.25MHz PAL B/G

2 175.25MHz PAL B/G

3 519.25MHz PAL B/G

4 855.25MHz PAL B/G

5 215.25MHz PAL 1

6 639.25MHz PAL 1

7 77.25MHz PAL D/K

8 55.25MHz NTSC M

9 55.25MHz --- B/G

10 55.25MHz --- ---

Channel Edit

ENGLISH

: select RED/GREEN/YELLOW/BULE MENU : exit

: select RED/GREEN/YELLOW/BULE MENU : exit

4.2 Skip: if there is channel that you would like to skip, you can use “Blue” key in “Channel Edit” menu and change the Sound System in the
TV System to “---“ and then exit the “Channel Edit” menu. After this, use “Channel Up/Down” key to change channels, it will skip the
channel that Sound System has changed to “---“

Sound System

- - - - - - - - - -

: select Col or System

4.3 Auto Clean Channel List: when the user exit the “Channel Edit” menu, the system will automatically delete the channels whose Sound
System set to “---“ at the bottom of the list

Channel Edit

CH Name Frequency TV System

1 A01. 55.25MHz NTSC M

2 61.25MHz NTSC M

3 XYZ+ 67.25MHz NTSC M

4 77.25MHz NTSC M

5 83.25MHz NTSC M

6 91.25MHz NTSC ---

7 97.25MHz NTSC ---

8 97.25MHz --- ---

9 97.25MHz --- ---

10 97.25MHz --- ---

CH Name Frequency TV System

1 A01. 55.25MHz NTSC M

2 61.25MHz NTSC M

3 XYZ+ 67.25MHz NTSC M

4 77.25MHz NTSC M

5 83.25MHz NTSC M

6 91.25MHz NTSC ---

Channel Edit

: select RED/GREEN/YELLOW/BULE MENU : exit

: select RED/GREEN/YELLOW/BULE MENU : exit

3. MPX(I/II) of remote control:

The MPX(I/II) button of remote control is used only when using the TV system and different TV system will present difference selection.

When a bilingual program is received, the sound mode display appears as shown on the right. Press the MPX(I/II) button to select the sound to be

heard

1). PAL TV SYSTEM :

NICAM_DUAL and NICAM_STEREO (2nd Audio program) sound program

NICAM_DUAL signal received

Each time the button is pressed, NICAM_DUAL_I, NICAM_DUAL_II or FM MONO appears on the screen.

NICAM_STEREO signal received

NICAM_STERRO, NICAM_MONO or FM MONO appears on the screen.

NICAM_MONO signal received

Each time the button is pressed, NICAM_MONO or FM MONO appears on the screen.

FM_STEREO sound received

Each time the MPX(I/II) button is pressed, FM STEREO, FM MONO will appear on the screen.

FM_DUAL sound signal received

Each time the MPX(I/II) button is pressed, FM MONO, FM DUAL I, FM DUAL II will appear on the screen.

FM_MONO Monaural sound

When a monaural program is received, the sound mode display will be shown. You can press the MPX(I/II) button to manually select monaural Sound.

BTSC sound signal received

Each time the MPX(I/II) button is pressed, MONO, STEREO will appear on the screen. If channel program support second language, SAP will appear

on the screen.

A

OPERATING INSTRUCTIONS (continued)

ASPECT

Each time the ASPECT button of the remote control is pressed, the screen
display size will change in sequence and the status will be displayed at the
bottom of the screen.

During TV/VIDEO signal input (AV 1,AV 2, AV 3 (option))

Full Screen Pillar Box

Panoramic Letter Box Expand

Note: For VGA, you can select Full Screen and Pillar Box

SPECT

ENGLISH

SELECT
buttons

ZOOM

Each time when   SELECT is 16:9, the ZOOM button of the remote control is pressed, the screen display zoom size will extend linearly

(Zoom=0~ 5 in sequence)

Resolution Full display Display
Display Full(Zoom=0) Zoom1 Zoom2 Zoom3~Zoom5
TV
AV 1
AV 2
AV 3 (Option)

HDMI

Processes such as expansion are performed for the above signal display. Because of this, there is a possibility that flicker may
become noticeable on Zoom = (1 ~ 3) depending on the display contents.

Image extend

linearly

29

OPERATING INSTRUCTIONS (continued)

Teletext Menu

Teletext is an information system broadcast by certain channels which can be consulted like a

newspaper. It also offers access to subtitles for viewers with hearing problems or who are not

familiar with the transmission language (cable networks, satellite channels, etc.).

Press TEXT / MIX Key: This is used to call teletext, and exit this function when press again

0/ 9

Press

This is used to select a page when TEXT function enable, enter the number of the page required

using the 0 to 9 to select a desired page, example: page 120, enter

CH

 and CHcan select page up or page down.

Press

Colour areas are displayed at the bottom of the screen. The 4 coloured keys are used to access

the items or corresponding pages.

or and :

direct access to the items.

1 2 0

Press TEXT / MIX key:

This is used under TEXT function enable. The function is to mix current TV image and teletext
display, press MIX key again to disable the mix function .

ENTER

TEXT

Text / MIX

SELECT
buttons

Colour
keys

30

TROUBLESHOOTING

Symptoms

If the point to check does not correct the symptoms, please contact your local Service center for assistance.

WARNING

Self servicing can be hazardous.

There is no picture and the power-indicating lamp
is off.

Symptom Point to check

Check to see that the power cable is properly
connected.

Press the main switch.

See Page

18

c

ENGLISH

The message “No Signal ” or “Going To Deep
Sleep” is displayed.

There is no picture and the power indicating lamp
lights Amber.

The message “Invalid Scan Freq.” is displayed.

The power indicating lamp is lit normally but there
is no picture.

The display image appears slanted.

Text displayed across the screen appears vertically
streaked, with the characters in vertical columns
blurred.

Text displayed across the screen appears blurred.
A fine pattern flickers when displayed on the
screen.

No Singal

Invalid mode

No sync signal is detected.

Check that the signal cable is properly connected.

Make sure that the computer, imaging equipment,
etc., is turned on.

Make sure the computer is not in power-save mode.

Ensure that the input selection matches the
connection terminal.

An input signal is received abnormally.

Ensure that the input signal matches the monitor
specifications.

Check to see that the signal cable is properly
connected.

Check the contrast and brightness settings (adjust
them for higher contrast and brightness).

Check to see that the signal cable is properly
connected.

Adjust the clock frequency and the phase. (Adjust
the clock frequency first, the dot clock phase next.)
(VGA input)

Adjust the clock phase till the desired clarity is
obtained.
(RGB input)

14

14
37
13

21
13

26

26

26

14

The remote control does not work.

Ensure that the batteries in the remote control are
inserted with the correct polarity.

Check to see that the batteries in the remote control
are functional.

16

31

TROUBLESHOOTING(continued)

Symptoms(continued)

Symptom Point to check

The temperature of the display panel surface is
warm.

The LCD display panel works by lighting phosphors. In some cases, this may
cause the temperature of the panel surface to increase. Please note that this
is not a malfunction.

See Page

-

Points that do not light, points with brightness
different from that of the periphery, points with color
different from that of the periphery, etc.

Coarse horizontal stripes appear in FULL display.

The screen flickers in the form of horizontal lines
oscillating up and down.
(PC INPUT MODE only)

The top surface of the monitor heats up. When used for long periods of time, the top surface of the monitor may heat

Text characters are displayed with varying
thickness.

The display does not seem bright enough.

The display does not seem bright enough. (RGB
input)

High-precision technology is used to manufacture the LCD display panel,
However over the life of the LCD panel, a few pixel elements may fail. This is
not to be considered a defect in the panel.

Adjusting the Clock Phase will reduce the horizontal stripes. (RGB input)

If the frequency from the computer is below 75Hz, try a higher frequency (to a
maximum limit of 75Hz). There may be a slight attenuation of the current
image.

up. This is not a malfunction.

The thickness of characters and lines may vary when images with a vertical
resolution greater than 720 lines are displayed; however this is not a
malfunction.

The ambient temperature of the monitor may be low. Ambient temperatures
less than about 15° degrees, may cause lower luminance.

The panel protection circuit automatically lowers the luminance, and is not a
malfunction. The luminance will be restored when power is turned on for a
while.

The setup-frequency setting in RGB input may be set to PC mode. When set
to PC mode, the luminance is lowered by about 10% than when set as Movie
mode. This is not a malfunction. If you do not mind flicker on the display,
please switch to Movie mode.

-

26

13

-

-

-

-

32

K

TROUBLESHOOTING(continued)

Symptoms(continued)

Make the checks suggested below depending on the symptoms observed. If the symptoms remain unresolved, contact your dealer.

WARNING

Do not attempt to service this unit.

Symptom Possible reason Remedy

ENGLISH

snowy picture - poor sound

multiple images - sound O.

intermittent interference

no picture or sound

(1)Connection of antenna/cable lead in wire to
the TV is poor
(2)Corroded or poor antenna/cable
connections
(3)Antenna has moved position
(4)Adverse weather conditions
(5)Transmitter problems

(1)Antenna has moved position
(2)Adverse weather conditions
(3)Transmitter problems
(4)AV Input is not set correctly
(5)Corroded or poor antenna / cable
connections

(1)Interference from electrical or mechanical
motors, fluorescent lights, portable radios
etc.
(2)Corroded or poor antenna/cable
connections.

(1)Make new connection and/or change
antenna plug
(2)Make new connections or use new cable.
(3)Re-align the antenna
(4)None

(5)Check with the local Operator

(1)Re-align the antenna
(2)None
(3)Check with the local Operator
(4)Check the external equipment connected
(5)Make new connections or use new cable.

(1)Check devices for shielding and renew if
necessary or move further from TV
(2)Make new connections or use new cable.

(1)TV may be in AV mode

(2)Picture/sound setting is set to minimum

(3)TV is in standby or power save mode

(4)Corroded or poor antenna / cable
connections.

(1)Press the PROGRAM button or thebtok

buttons on your remote control to return to

normal TV mode
(2)Check picture / sound controls (go to MAIN
MENU)
(3)Press POWER ON / OFF button
(4)Make new connections or use new cable.

TV

33

TROUBLESHOOTING (continued)

Abnormal Displays Corrections VGA Only

Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the adjustments
suggested below. (only forVGA)

Symptom 1

Example

Text displayed across the screen appears vertically streaked, with some characters blurred (figure 1).
The display image appears flowing (figure 2) (VGA input).

Figure 1

Vertical
streaks

Before
adjustment
Some

After
adjustment

After
adjustment
All characters

Adjustment procedure 1) Press the MENU button. The Main Menu will be displayed.

2) Press the  SELECT button and Select Setup.

3) Press the ENTER button. The Setup Menu will be displayed.

4) Press the  SELECT button and select Auto Adjust.

When adjustment is not possible with Auto Adjust:

5) Press the MENU button. The Main Menu will be displayed.

6) Press the  SELECT button and select Setup.

7) Press the ENTER button. The Setup Menu will be displayed.

8) Press the  SELECT button and select Horizontal Clock.
(Displays fine patterns as characters or a vertical striped pattern over the entire screen during Horizontal Clock
adjustment.)

9) Press the  or  ADJUST buttons and search for clear characters over the entire screen.

10) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.

The display image may be momentarily disturbed during clock adjustment but this is not a failure.

Symptom 2

Example

Text displayed across the screen appears blurred in its entirety (figure 2).
A fine pattern flickers when displayed on the screen (figure 3).

Figure 2

Before adjustment

After adjustment

Figure 3

Adjustment procedure 1) Press the MENU button. The Main Menu will be displayed.

2) Press the  SELECT button and Select Setup.

3) Press the ENTER button. The Setup Menu will be displayed.

4) Press the  SELECT button and select Auto Adjust.

When adjustment is not possible with Auto Adjust

5) Press the MENU button. The Main Menu will be displayed.

6) Press the  SELECT button and select Setup.

7) Press the ENTER button. The Setup Menu will be displayed.

8) Press the  SELECT button and select Clock Phase.
(Displays fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)

9) Press  or  ADJUST buttons to make the text
appear clean across the screen.

9) Press  or  ADJUST buttons to make the text
appear without flickering.

Before adjustment

After adjustment

34

PRODUCT SPECIFICATIONS

Panel

Net dimensions 790 (W) x 585.3 (H) x 308.5 (D) mm (Speaker W/I under)

Net weight 18.5+-0.5 kg (including Speakers / Stand)

Ambient
conditions

Power supply AC100 - 240V, 50/60Hz

Power consumption/at standby 220W / < 2W

Audio output Speaker 10W + 10W (8 ohms)

(RGB input)

Input signals

Display dimensions

Resolution 1360 (H) x 768 (V) pixels

Temperature

Relative Humidity Operating: 20% to 80%, Storage: 20% to 90% (non-condensing)

Input terminals

Video signals 0.7 V

Sync signals

Approx. 26inches (575.769 (H) × 323.712 (V) mm)

Operating: 5°C to 35°C, Storage: -15°C to 60°C

Audio input terminal (3.5mm Stereo Mini Jack)
VGA analog RGB input terminal (D-sub 15-pin)
HDMI input terminal

H/V separate, TTL level
H/V composite, TTL level

ENGLISH

(Video input)

Input terminals

Input signals

Video signals

Video output Signal

Input terminals ANT: 75 ohms Unbalanced

Input signals

RF Video stem

z It takes at least 30 minutes to attain the maximum picture quality.

AV1 IN: Composite video, S-VIDEO input terminal for CVBS(RCA), S-VIDEO(4 pin mini din)
AV1 IN: L/R audio input terminal for CVBS or S-Video (RCA)
AV2 IN: Composite video, Component input (Y-CbCr or Y-PbPr)(RCA)
AV2 IN: L/R audio input terminal (RCA)
AV3 IN (option): Composite video, S-VIDEO input terminal for CVBS(RCA), S-VIDEO(4 pin mini din)AV3 IN:
L/R audio input terminal for CVBS or S-Video (RCA)

AV1,AV3 (option):NTSC-M/PAL/SECAM
AV2, :480i,480p,576i,576p,720p/60,720p/50,1080i/60,1080i/50

OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)

PAL – DK / BG / I / M
NTSC – M / DK / BG / I
SECAM – DK / BG / I

35

PRODUCT SPECIFICATIONS (continued)

Component Connection

Component Connection

VGA Input (D-sub 15 pin connector)

Pin Input signal

1 R

2 G or sync on green

3 B

4 No connection

5 No connection

6 R.GND

7 G.GND

8 B.GND

9 No connection

10 GND

11 No connection

12 [SDA]

13 H. sync or H/V composite sync

14 V.sync. [V.CLK]

15 [SCL]

HDMI Input

Pin Input Signal Pin Input Signal

1 T.M.D.S. Data2+ 14 No Connect

2 GND 15 SCL

3 T.M.D.S. Data2- 16 SDA

4 T.M.D.S. Data1+ 17 GND

5 GND 18 +5V

6 T.M.D.S. Data1- 19 HPDET

7 T.M.D.S. Data0+

8 GND

9 T.M.D.S. Data0-

10 T.M.D.S. CLK+

11 GND

12 T.M.D.S. CLK-

13 No Connect

When different kinds of input signals are simultaneously input to the TV
via a graphics board or the like, the TV will automatically select the
signals in the following priority order:

Sync signal type Priority

H/V separate sync. 1

H/V composite sync. 2

*Even in the case of the recommended signals shown on the following
page, there may be instances when correct display is not possible. In
this case, use H/V separate sync, or H/V composite sync.

sync. on Green * 3

36

PRODUCT SPECIFICATIONS (continued)

Recommended Signal List

Digital HDMI Video Timing Chart

No. Resolution H-freq (kHz) V-freq. (Hz) Preposed Remark

Video ( Digital)

1 720 x 480i 15.734 60
2 720 x 480P 31.5 60
3 720 x 576i 15.625 50
4 720 x 576P 31.25 50
5 1280 x 720P 45 60
6 1280 x 720P 37.5 50
7 1920 x 1080i 33.75 60
8

Vertical lines : standare ±14 lines

Analog RGB Video Timing Chart

1920 x 1080i 28.125 50

Note : Vertical frequency : standard ±1Hz

ENGLISH

No. Resolution H-freq (kHz) V-freq. (Hz) Preposed Remark

PC ( Analog)

A 640 x 350 31.5 70

B 640 x 480 31.5 60 VGA
C 640 x 480 37.5 75 VGA
D 720 x 400 31.5 70
E 800 x 600 37.9 60 SVGA
F 800 x 600 46.9 75 SVGA
G 1024 x 768 48.4 60 XGA
H 1024 x 768 56.5 70 XGA

I 1024 x 768 60 75 XGA

J 1280 x 768 48.1 60 SXGA

37

With Composite Input and S-video Input (AV1~AV2 input)

Signal mode

No.

1 NTSC-M 525 59.94 15.73

2 PAL 625 50 15.625

3 SECAM 625 50 15.625

Signal

name

Resolution

Vertical

frequency

(Hz)

Horizontal
frequency

(kHz)

Remarks

With Y, Cb, Cr / Y, Pb, Pr input (AV2 component input)

Signal mode

No.

1 480i 480 59.94 15.73

2 480p 480 59.94 31.47

3 576i 576 50.00 15.63
4 576p 576 50.00 31.26
5 720p/50 720 50.00 37.50
6
7 1080i/50 1080 50.00 28.13
8 1080i/60 1080 60.00 33.75

z The TV differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal polarities.

z Displaying images is not 720 lines of vertical resolution at Full display (compressed display) can result in the interpolation of stripes

Signal

name

720p/60 720 60.00 45.00

Note that different signals having all these elements alike may be handled as the same signal.

Resolution

Vertical

frequency

(Hz)

Horizontal

frequency

(kHz)

Remarks

TRUCTIONS (continued)

38

Consumer Information Centres

SERVICE CONTACTS

If problems remain after checking this manual, please contact your place of purchase or contact:

Australian Service Contacts,
Visit the Customer Support section of Mitsubishi Electric Australia’s web site at
www.mitsubishielectric.com.au for details of your nearest Mitsubishi Electric Authorised Service Center,
or contact the Service Department for your state:

New South Wales and Australian Capital Territory
348 Victoria Road
Rydalmere, NSW, 2116
Telephone: [phone]
Fax: [phone]

Queensland
Unit 12 469 Nudgee Road
Hendra, QLD, 4011
(Airlink Business Park)
Telephone: [phone]
Fax: [phone]

South Australia and Northern Territory
77 Port Road
Hindmarsh, SA, 5007
Telephone: [phone]
Fax: [phone]

Victoria and Tasmania
4 / 303 Burwood Hwy
East Burwood, VIC, 3151
Telephone: [phone]
Fax: [phone]

Western Australia
5 / 329 Collier Road
Bassendean, WA, 6054
Telephone: [phone]
Fax: [phone]