Diamond Digital
DV170J/JB
Colour TFT LCD Monitor
17” (43 cm) LCD Panel Size
Copyright 2005, Mitsubishi Electric Australia Pty. Ltd. All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or
translated into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission.
Table of Contents
Important Safety Instructions ..........................................1 1
1
Features.............................................................................2 2
2
3 Unpacking the Monitor.....................................................3
3
4 Hardware Installation .......................................................5
5 Windows driver installation .............................................7
5
6 Setting the Display Resolution........................................8
Choosing the Best Resolution........................................... 8
Supported Graphics Modes and Refresh Rate Selection..9
7 Adjusting the Monitor..................................................... 13
7
User Controls.................................................................. 13
Adjusting the Monitor's Display .......................................14
OSD Function Menu .......................................................14
Function Description .......................................................14
Frequently Asked Questions .........................................18 8
8
Specifications .................................................................20 9
9
10 Service Contacts.............................................................22
i
Disclaimer
Mitsubishi Electric Australia Pty. Ltd. makes no representations or warranties,
either expressed or implied, with respect to the contents hereof and
specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Further, Mitsubishi Electric Australia reserves the right to
revise this publication and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or changes.
Diamond Digital is a registered trademark of Mitsubishi Electric Australia Pty. Ltd.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
All other trademarks remain the property of their respective owners.
Reference Information
For future reference, write the following information about your monitor in
the space below. The serial number is found on the back of the product or
on the bottom of its stand.
Monitor Information
Product Name: DV170J/JB
Serial Number:
Date of Purchase:
Dealer Information
Dealer:
Telephone
Number:
Address:
ii
11
Please read the following safety instructions before installing or cleaning your
Diamond Digital monitor:
1. Unplug the monitor’s power cable from the wall outlet before cleaning. Do
2. Slots and openings on the back or top of the cabinet are provided for
3. Never push objects of any kind, or spill liquid of any kind into this product.
4. Do not attempt to service this product yourself as opening or removing
5. Do not apply pressure to the LCD screen. Excess pressure can damage
6. If any abnormal operation or accident (such as dropping the unit) occurs,
Important Safety Instructions
not use liquid or aerosol cleaners. Use a soft cloth to clean the monitor
housing.
ventilation. They must not be blocked or covered. This product should
never be placed near or over a radiator or other heat source, or used in a
built-in installation unless proper ventilation is provided.
covers may expose you to dangerous voltages or other hazards.
the LCD panel.
disconnect the monitor from the wall power outlet and contact qualified
service personnel.
7. Turn the audio volume control of the built-in speakers to minimum (0) and
turn the monitor off before connecting or disconnecting any audio cable.
1
1
2
2
Your DV170J/JB Monitor features:
♦ XGA (1280 x 1024 pixel) Resolution LCD Panel
♦ High Brightness Level – 270 cd/m
♦ High Contrast Ratio – 450:1 (typical)
♦ Response Rate – 12 ms (Typical) (Tr+Tf)
♦ True Colour Display
♦ High Quality Ratiometric Expansion
♦ Plug and Play Compatibility with Microsoft
♦ Space Saving - only 190 mm deep
♦ Light Weight - only 5 kg
♦ Lower Power Consumption
Features
2
(typical)
With 16.2M (6bit + FRC) colour, the DV170J/JB monitor offers you better
image quality.
With any resolution within the monitor’s specified range, your Diamond
Digital DV170J monitor can expand the image to full screen.
®
Windows® 95, 98, 2000,
Me and XP
40W maximum during operation with audio.
♦ Power Saving
Power management complies with VESA DPMS standard. When the
system is idle (in monitor off mode), the monitor automatically cuts its
power consumption to less than 3 W.
♦ On Screen Display
Allows you to adjust all settings simply using on-screen menus.
♦ Support Kensington security locks
2
2
r
V
3
3
Please check that the following items are included with your monitor. If they are
missing or damaged, please contact your place of purchase
Unpacking the Monitor
immediately.
LCD monito
User’s Manual
s
'
r
e
s
l
U
a
u
n
a
M
GA Cable
Power Cord
3
3
Locate the model name and the serial number label on the back of your monitor,
and write the details of the monitor and your place of purchase in the space on
page (ii) of this manual for future reference.
4
4
4
4
Hardware Installation
Connecting the Monitor Base
Remove the base from the packing box and place
it on the desk. Next, remove the LCD display and
carefully seat it on the base. (See fig.1-1 )
Viewing Angle Adjustment
The LCD Monitor is designed to allow users
to have a comfortable viewing angle. The
viewing angle can be adjusted from -5°to
+30°.(See fig. 1-2)
Figure 1-1
Figure 1-2
5
5
Connecting the Display to your Computer
Using the VGA cable
1. Power off your computer.
2. Connect one end of the VGA signal cable to the LCD
Monitor’s VGA port. (See Fig 1-3)
3. Connect the other end of the signal cable to the VGA
port on your PC.
4. Make sure connections are secure.
Connecting the AC Power
1. Connect the power cord to the monitor. (See Fig. 1-4)
2. Connect the power cord to an AC power source.
Figure 1-3
Instructions for VESA Mounting
To detach the LCD Monitor from its stand, unscrew the
two screws n for the monitor stand and pull it downwards
to remove, then unscrew the four screws o for the
monitor stand bracket and pull this down to remove.
Interface for Arm Applications
Before installing the mounting device, please refer to
Fig.1-7.
The rear of this LCD display has four integrated 4 mm, 0.7
pitch threaded nuts, as well as four 5mm access holes in
the plastic covering as illustrated in Figure 1-2. (These
specifications meet the VESA Flat Panel Monitor Physical
Mounting Interface Standard).
6
6
Figure 1-4
Figure 1-6
Figure 1-7
5
5
The DV170J/JB is fully Windows Plug and Play compatible so no specific
Windows drivers are required for installation.
Windows 98, ME, and 2000
The first time you start Windows after connecting your new monitor, the system
will detect the monitor and automatically start the Add New Hardware wizard.
Just follow the prompts to load the native Plug and Play drivers.
Windows XP
The first time you start Windows after connecting your new monitor Windows
XP will automatically load the native Plug and Play drivers.
Windows driver Installation
7
7
6
6
Choosing The Best Resolution
All Liquid Crystal Displays (LCDs) have a fixed resolution that is the same as
the maximum resolution that may be displayed on the LCD. In the case of the
DV170J/JB the LCD resolution is 1280 x 1024 pixels. This is also known as the
“native” resolution of the monitor. Lower resolutions can be displayed at full
screen through an interpolation circuit. Because the lower resolution must be
expanded, the quality of the displayed image is not as good as that available
when the native resolution is displayed. For optimal performance from any LCD
monitor, you must use the monitor’s native resolution.
If you are using Windows 95, 98, 2000, Me, XP or NT 4.0, you can change the
resolution as follows:
1. Double-click the Display icon in the control panel.
2. From the Display Properties dialogue box, select the Settings tab.
Setting the Display Resolution
There is a slider on the right-hand side in the middle of the dialogue box
that alters the displayed resolution. Set the resolution to 1280 x 1024.
3. For Windows NT users only: select a refresh rate of 60Hz and click Te st .
A test pattern will be displayed. Make sure that there are no error
messages shown by the monitor. If an error message is displayed, check
the resolution and refresh rate settings or choose a different refresh rate.
4. Click OK to close Display Properties.
8
8
If you are using an Apple Macintosh, change the resolution by doing the
following:
MacOS 8.x/9.x
1. Click the Apple icon at the top, left corner of the screen, select Control
Panel and then select Monitors.
2. Select a resolution of 1280 x 1024 pixels with between 60Hz refresh rate.
3. If refresh rates of 60Hz are not available, click Recommended in the
Show drop-down box and change it to All. Select the resolution and
refresh rate as above.
A colour depth of either Thousands or Millions is recommended.
MacOS X
1. Click the Apple icon at the top, left corner of the screen, select System
Preferences and then select Displays.
2. Select a resolution of 1280 x 1024 pixels with between 60Hz refresh rate.
3. A colour depth of either Thousands or Millions is recommended.
Supported Graphics Modes and Refresh Rate Selection
There is no need to choose the highest possible refresh rate when using an
LCD monitor. It is not technically possible for an LCD monitor to flicker. Even at
a refresh rate of 60 Hz you will get an absolutely flicker-free image.
For best results, it is important that you set the graphics adaptor to use one of
the monitor’s preset display modes shown in Tab le 1 on the next page. Other
graphics signals may be displayed poorly or not at all. Note that the
DV170J/JB’s preset modes correspond to VESA or Apple Macintosh standard
graphics signals for these resolutions. All recent models of graphics adaptor
should be able to support these modes. For the native resolution of 1280 x
1024 pixels, for example, refresh rates of 60, 70 and 75 Hertz are supported.
With Windows 95, 98, ME, 2000 or XP you can change the refresh rate of the
9
9
graphics signal as follows:
1. Double click the Display icon in the control panel.
2. From the Display Properties dialogue box, select the Settings tab and
click the Advanced Properties button.
3. For Windows 95, 98, and ME select the Adapter tab, for 2000 and XP
select the Monitor tab. The refresh rate selection field is located in the
centre, at the bottom of the dialogue box.
4. Choose a refresh rate that corresponds with one of the factory modes from
the table below.
5. Click Apply, and then OK twice.
Please Note:
• Graphics modes that are not listed in the table may not be supported. For
an optimal picture it is recommended that you choose a graphics mode
with a resolution of 1280 x 1024 pixels that is listed in Table 1 on the next
page. Resolutions of 640 x 480, 800 x 600 and 1024 x 768 pixels are
supported. The default setting may require some adjustment before use.
• The displayed image may show some distortion or noise that can be
caused by the signal from the VGA card if it does not correspond with the
usual standard. This is not however, a problem with the monitor. If it is still
visible after using the Automatic adjustment, you can usually improve the
displayed image by manually adjusting the phase, horizontal position and
pixel frequency settings using the "Geometry" menu. See Chapter 7,
Adjusting the Monitor, for more details.
• When you shut Windows down you may see interference lines on your
screen. This caused by the manner in which Windows controls the
graphics card at this point and is normal with all LCD monitors.
• To extend the service life of the product, we recommend that you use your
computer's power management functions to turn the monitor off after
extended idle periods.
10
10
Table 1
Standard Timing Table
If the selected timing is NOT included in table below, this LCD monitor will use the
most suitable available timing.
TIMING FH(KHZ) SYNC TOTAL ACTIVE SYNC FRONT BACK PIXEL
FV(HZ) WIDTH PORCH PORCH
640x350 31.469 + 800 640 96 16 48 25.175
VGA-350 70.087 – 449 350 2 37 60
640x400 24.83 – 848 640 64 64 80 21.05
NEC PC9801 56.42 – 440 400 8 7 25
640x400 31.469 – 800 640 96 16 48 25.175
VGA-GRAPH 70.087 + 449 400 2 12 35
640x400 31.5 – 800 640 64 16 80 25.197
NEC PC9821 70.15 – 449 400 2 13 34
640X480 31.469 - 800 640 96 16 48 25.175
VESA-PAL 50.030 - 629 480 2 62 85
640x480 31.469 – 800 640 96 16 48 25.175
VGA-480 59.94 – 525 480 2 10 33
640x480 35.00 – 864 640 64 64 96 30.24
APPLE MAC-480 66.67 – 525 480 3 3 39
640x480 37.861 – 832 640 40 16 120 31.5
VESA-480-72Hz 72.809 – 520 480 3 1 20
640x480 37.5 – 840 640 64 16 120 31.5
VESA-480-75Hz 75 – 500 480 3 1 16
720x400 31.469 – 900 720 108 18 54 28.322
VGA-400-TEXT 70.087 + 449 400 2 12 35
832x624 APPLE 49.725 – 1152 832 64 32 224 57.2832
MAC-800 74.55 – 667 624 3 1 39
800x600 35.156 + 1024 800 72 24 128 36
SVGA 56.25 + 625 600 2 1 22
800x600 37.879 + 1056 800 128 40 88 40
VESA-600-60Hz 60.317 + 628 600 4 1 23
800x600 48.077 + 1040 800 120 56 64 50
VESA-600-72Hz 72.188 + 666 600 6 37 23
TIMING FH(KHZ) SYNC TOTAL ACTIVE SYNC FRONT BACK PIXEL
FV(HZ) WIDTH PORCH PORCH
800x600 46.875 + 1056 800 80 16 160 49.5
VESA-600-75Hz 75 + 625 600 3 1 21
1024x768 48.363 – 1344 1024 136 24 160 65
XGA 60.004 – 806 768 6 3 29
1024x768 53.964 + 1328 1024 176 16 112 71.664
COMPAQ-XGA 66.132 + 816 768 4 8 36
1024x768 56.476 – 1328 1024 136 24 144 75
VESA-768-70Hz 70.069 – 806 768 6 3 29
1024x768 60.023 + 1312 1024 96 16 176 78.75
VESA-768-75Hz 75.029 + 800 768 3 1 28
POLARITY (DOT/
LINE)
POLARITY (DOT/
LINE)
(DOT/
LINE)
(DOT/
LINE)
(DOT/LINE) (DOT/LINE) (DOT/LINE)
(DOT/LINE) (DOT/LINE) (DOT/LINE)
FOREQ
(MHZ)
FOREQ
(MHZ)
11
11
1024x768 60.24 – 1328 1024 96 32 176 80
APPLE MAC-768 75.02 – 803 768 3 3 29
1152x864 54.054 + 1480 1152 96 40 192 80
(60Hz) 59.270 + 912 864 3 13 32
1152x864 63.851 + 1480 1152 96 32 200 94.499
(70Hz) 70.012 + 912 864 3 1 44
1152x864 67.50 + 1600 1152 128 64 256 108.00
(75Hz) 75.00 + 900 864 2 2 32
1280x960 60.00 + 1800 1280 112 96 312 108.00
(60Hz) 60.00 + 1000 960 3 1 36
1280x960 70.00 + 1800 1280 112 96 312 126.00
(70Hz) 70.00 + 1000 960 3 1 36
1280x960 75.00 + 1800 1280 112 96 312 135.00
(75Hz) 75.00 + 1000 960 3 1 36
1024-60Hz
1024-75Hz
64 + 1688 1280 112 48 248 108 1280x1024VESA60 + 1066 1024 3 1 38
80 + 1688 1280 144 16 248 135 1280x1024VESA75 + 1066 1024 3 1 38
Note: Mode 640x350, 640x400 and 720x400 will locate on middle position but cannot
be expanded to full
12
12
7
7
User Controls
A brief description and the location of all LCD Monitor function controls and
indicators:
Adjusting the Monitor
Figure 2-1
1 Soft Power Switch
2 Power-On Indicator
Function Select
3
Buttons
Adjustment Control
4
Buttons
Press the power switch to switch the monitor ON/OFF.
LED lights Green color --- Power is ON.
LED lights Yellow --- Monitor is in "Power Saving Mode".
LED is off --- Power is OFF.
Press either left or right control button for OSD (On Screen Display)
menu selection.
Press the left button to decrease the OSD setting and press the right
button to increase the OSD setting.
13
13
Adjusting the Monitor's Display
The monitor has four function control buttons to select among functions shown on OSD menu,
designed for easy user-viewing environments.
OSD Function Menu
To access the OSD Main menu, simply press one of
the Function Select control buttons, and the menu
diagram will pop up on the screen as shown on Fig.
2-2:
Continue pressing the Function Select buttons to
scroll through the available menu items, then press
the Adjustment Control buttons to adjust the setting
of a selected item.
Figure 2-2
Function Description
Icon Function Function Description
Brightness
Contrast
H. Position
V. Position
Sharpness
OSD
Transparency
This function lets you increase and decrease the screen brightness.
This function lets you increase and decrease the contrast level of the
screen.
This function let's you adjust the display's horizontal position. (Not
available when using DVI).
This function let's you adjust the display's vertical position. (Not
available when using DVI).
This function let's you adjust the images sharpness. Five selections are
available. A smoother setting is more suitable for pictures, while a
sharper setting is more suitable for text. (Not available when using DVI).
This function let's you set the transparency of the OSD menu (Not
available when using DVI).
Phase
Clock
This lets you adjust the phase of the pixel clock to eliminate sampling
noise (Not available when using DVI).
Adjusts the sampling frequency for the Analogue (VGA) to Digital signal
conversion (Not available when using DVI).
14
14
OSD H. Position
Colour
Temperature
This function lets you select a colour temperature. Using the Adjustment
Control buttons to select the required colour temperature. Please see
the diagram below for function and description. (Not available when
using DVI).
This function moves the OSD menu window horizontally.
OSD V. Position
TABLE 1
Graph / Text
Recall
Language
Auto and Input
Select
Exit
This function moves the OSD menu window vertically.
Because the H and V-Frequencies of both 640 x 400 70Hz, and 720 x
400 70Hz, are the same, this function let's you manually select either
640 x 400 (graphics mode), or 720 x 400 (text mode) when running in
DOS. (Not available when using DVI).
The recall function will return all adjusted parameters to factory preset
values.
Five OSD language options are available: English, German, French,
Spanish, and Italian. Press the left or right adjustment control button to
select other language.
This function lets you use the Automatic adjustment function to adjust
the Geometry based on the displayed image, or select either the
Analogue or Digital inputs
Exits the OSD menu.
Icon Function Description
9300
7500
6500
User
CIE coordinated Colour Temperature of
9300°K
CIE coordinated Colour Temperature of
7500°K
CIE coordinated Colour Temperature of
6500°K
Three colours (Red, Green, Blue) can be
adjusted from the OSD menu
Sets the CIE coordinate colour
temperature to 9300°K
Sets the CIE coordinate colour
temperature to 7500°K
Sets the CIE coordinate colour
temperature to 6500°K
Allows a user to define the CIE
Temperature settings.
Picture Optimisation
The easiest way to obtain an optimal picture is by using the Auto function in the
OSD menu. This only works reliably if the graphics adaptor is set to use one of
the monitor’s factory modes (see Table 1 in the previous chapter) and if you
are displaying a suitable stationary image (such as the Windows desktop).
15
15
The monitor will remember the settings obtained by the auto calibration
settings and use them whenever you turn the monitor on. Note that you may
need to readjust the monitor if it is connected to a different computer or if the
computer’s graphics adaptor is replaced.
If you are still not satisfied with the result, you can enhance the image by using
the monitor’s manual adjustment functions.
Manual Picture Adjustment
Adjustments to the displayed image and audio volume are made using the
On-Screen Display (OSD), and the buttons on the front of the monitor.
To manually adjust the image:
1. Display your operating system desktop
2. Open the OSD menu by pressing one of the Function keys on the monitor.
3. Press Fn► or ◄ to select the Clock function.
4. Press ► or ◄ to increase or decrease the sampling clock to get the
optimum picture. Look closely at the picture displayed, especially
surrounding text and icons, for any movement or change. Adjust the Clock
setting and see how this affects this “noise” or movement. Make sure that
in correcting noise in one part of the screen the setting does not create it in
another. You should, with careful adjustment, be able to obtain a picture
with no visible noise in any section of the screen.
5. If some noise or distortion is still visible select Phase using the Fn► or ◄
buttons.
6. With the Clock set to the optimal value adjust the Phase to further optimise
the displayed image. You should now be able, with a combination of the
Phase and Clock settings, to obtain a perfectly stable image.
7. Finalise the manual adjustment using the H. Position and V. Position
functions
If you are still not satisfied with the result, try repeating the above procedure
using a graphics signal that has a different refresh rate.
16
16
Please Note:
You must use one of the factory modes when manually adjusting the picture. If
you are having difficulties generating a supported mode, ask your computer
dealer or the distributor or manufacturer of your graphics card for assistance.
The procedures described in this chapter should be performed for every
resolution and type of graphics signal that you wish to use. For example, if a
particular application requires a resolution of 800 x 600 pixels, but all other
applications use the monitor’s native resolution, you will need to display the
test pattern and make adjustments twice.
The monitor will remember your settings and use them whenever you turn the
monitor on. Note that you may need to re-adjust the monitor if it is connected to
a different computer or if the computer’s graphics adaptor is replaced.
17
17
8
8
The image is blurred, how can I get the best quality picture?
♦ Read chapter 6, Setting the Display Resolution, and select a graphics
♦ Have you used a VGA extension cable?
♦ Does the blurring only occur at resolutions lower than the native
Why does the image look yellow, blue or pink instead of showing the
correct colours?
♦ The most common cause of this problem is a loose VGA signal cable or
♦ Check the VGA signal cable for damage. If any pins are bent or broken off,
Frequently Asked Questions
signal with the correct resolution and refresh rate. Then read chapter 7,
Adjusting the Monitor, and make adjustments to the displayed image
based on these instructions.
If so, remove the extension cable and check the displayed image. Has the
image quality improved? Optimise the image using the procedures in
chapter 7 with the extension cable removed. Reconnect the extension
cable once the image has been optimised. Depending on the
characteristics and type of the extension cable, some blurring or distortion
may occur due to conduction losses of the extension cable. You can
minimise these losses by using an extension cable with better conduction
quality or with a built-in booster.
(maximum) resolution?
Please read chapter 6, Setting the Display Resolution. Select a graphics
signal that uses the monitor’s the native resolution (1280 x 1024 pixels).
connector. Check that the cable is securely connected to the computer.
contact your dealer or an authorised Mitsubishi Electric service agent (see
Chapter 10 for details).
18
18
No image is displayed, what can I do?
♦ Check that the light (LED) next to the monitor’s power button is lit and is
green in colour. If the LED is green, press one of the Function Select
buttons on the monitor to access the On Screen Display. If the message
NON PRESET MODE appears there, please read chapter 6, Setting the
Display Resolution and reset the graphics card to one of the monitor’s
supported graphics signals.
♦ If the LED is orange the monitor is in power saving mode. Press a button
on the computer keyboard or move the mouse to wake the computer. If that
does not help, check that the VGA cable is securely plugged into the
computer. Also check the pins of the VGA cable’s connector. If any pins are
bent or broken off, then contact your dealer (see Chapter 10 for details).
♦ If the LED is not lit at all, check that the monitor is plugged into the power
supply mains socket and that the power switch is turned on. Check that the
monitor’s power switch is also turned on.
The image is or distorted, flashes or flickers:
♦ Check that the monitor’s signal cable is securely connected to the
computer.
♦ Read the chapters 6 and 7 of this manual, then select the correct
resolution, refresh rate and make adjustments based on these instructions.
The image is displaced in one direction:
♦ Use the H. Position (horizontal position) adjustment in the monitor’s OSD
to reposition the image.
♦ Read the chapters 6 and 7 and then select the correct resolution, refresh
rate and make adjustments based on these instructions.
19
19
9
9
Model: DV170J/JB
Display Characteristics
Display Type 17“ active matrix Thin Film
Viewable Diagonal Area 43 cm / 17”
Native (Maximum) Resolution 1280 x 1024 pixels
Colours 16 million (6 bit + FRC)
Contrast Ratio 450:1 (typical)
Brightness 260 cd/m² (typical)
Response Time 12 ms (typical)
Viewing Angle (Horizontal, Vertical) -60°/+60°, -40°/+60°(typical)
Dot Pitch 0.264mm x 0.264 mm
User Interface
Controls Power switch with LED indictor
Specifications
Transistor Liquid Crystal Display
On-Screen Display Functions Contrast, Brightness, Vert. & Hor.
Position, Phase, OSD Position,
Auto Adjustment, Clock,
Graph/Text, language, Recall,
Colour Temperature, Exit,
Sharpness, OSD Transparency
Microprocessor Controlled Graphics
Modes
28 Preset modes:
Including 11 VESA & 4 DOS
20
20
Input Signal
Line Frequency 24 – 80kHz multi-frequency
Image Frequency (Refresh Rate) 49 - 75Hz
Video Signal RGB analogue (Positive polarity)
0.7 Vpp/75 Ohm
Synchronization TTL separate, composite TTL
Signal Connection 15-pin mini D-sub
Physical Characteristics
Power Management VESA DPMS, Energy Star
Maximum Power Consumption 48 Watts
Power Saving Mode < 3 Watts
Operating Voltage Automatic switched mode power
supply, 100 - 240 V, 50 - 60 Hz
Dimensions (W x H x D) 374mm x 387mm x 190mm
Weight 5 kg
Temperature (Operating) 5°C - 40°C
Air Humidity (Operating) 20% - 80%
Regulatory Certification
Safety AS/NZS 60950:2000
EMI/EMC AS/NZS CISPR22:2002 (C-Tick).
Other ISO 13406-2
21
21
0
110
If problems remain after checking this manual, please contact your place of
purchase or contact:
Australian Service Contacts
Visit the Customer Support section of Mitsubishi Electric Australia’s web site at
for details of your nearest Mitsubishi Electric Authorized Service Center or
contact the Service Department for your state:
New South Wales and Australian Capital Territory
348 Victoria Road
Rydalmere, NSW, 2116
Telephone: (02) 1300 651-808
Fax: (02) 9684-7684
Queensland
12 / 469 Nudgee Road
Hendra, QLD, 4030
Service Contacts
www.mitsubishielectric.com.au
(Airlink Business Park)
Telephone: (07) 3623-2000
Fax: (07) 3630-1888
South Australia and Northern Territory
77 Port Road
Hindmarsh, SA, 5007
Telephone: (08) 8340-0444
Fax: (08) 8340-0555
22
22
Victoria and Tasmania
4 / 303 Burwood Hwy
East Burwood, VIC, 3151
Telephone: (03) 9262-9899
Fax: (03) 9262-9850
Western Australia
5 / 329 Collier Road
Bassendean, WA, 6054
Telephone: (08) 9377-3411
Fax: (08) 9377-3499
23
23
Loading...