Mitsubishi 930, Diamond Pro 930SB User Manual

User’s Manual

www.nec-mitsubishi.com

Diamond Pro 930Diamond Pro 930

Diamond Pro 930Diamond Pro 930

Diamond Pro 930

SBSB

SBSB

SB

Declaration of the Manufacturer

NEC-Mitsubishi Electric Visual

Systems Corporation

686-1, Nishioi Oi-Machi

Ashigarakami-gun

Kanagawa 258-8533, Japan

We hereby certify that the

colour monitor Diamond Pro 930

SB

is in compliance with

Council Directive 73/23/EEC:

– EN 60950

Council Directive 89/336/EEC:

EN 55022
– EN 61000-3-2
– EN 61000-3-3
– EN 55024

and marked with

2 User’s Manual

ENERGYSTAR Product

As an ENERGYSTAR Partner, NEC-Mitsubishi Electronics Display of America, Inc. has determined that this
product meets the ENERGYSTAR guidelines for energy efficiency. The ENERGYSTA R emblem does not represent
EPA endorsement of any product or service.

IBM is registered trademark of International Business Machines Corporation.
Apple and Macintosh are registered trademarks of Apple Computer Inc.
Microsoft and Windows are registered trademarks of the Microsoft Corporation.
ENERGYSTAR is a U.S. registered trademark.
All other trademarks or registered trademarks are property of their respective owners.

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICE­ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK • DO NOT OPEN

This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations

according to C.S.A. C22.2 No. 950.

FCC Information

1. Use the attached specified cables with the Diamond Pro 930SB colour monitor so as not to interfere with
radio and television reception.

(1) Please use the supplied power cord or equivalent to ensure FCC compliance.

(2) Shielded captive type signal cable.

Use of other cables and adapters may cause intereference with radio and television reception.

2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy, and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult your dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional
suggestions. The user may find the following booklet, prepared by the Federal Communications Commission,
helpful: ”How to Identify and Resolve Radio-TV Interference Problems.“ This booklet is available from the U.S.
Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

Diamond Pro 930SB 3

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE
THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE
PRONGS CAN BE FULLY INSERTED.
EFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.

WARNING

4 User’s Manual

Contents

* Remember to save your original box and packing material to transport or ship the monitor.

CD-ROM

Your new Diamond Pro 930SB monitor box* should contain the following:

• Diamond Pro 930SB Monitor with tilt/swivel base

• Power Cord

• Captive Signal Cable

• User’s Manual

• Sales Office List

• CD ROM with Setup Software, complete User’s Manual and other helpful files.

To see the User’s Manual, Acrobat Reader 4.0 must be installed on your PC.

Power Cord

User’s Manual

Captive Signal Cable

Sales Office List

Diamond Pro 930SB 5

Quick Start

To attach the Diamond Pro 930SB monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2. If necessary, install the display card into your system. For more information, refer to the display card
manual.

3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable to the connector of the display card
in your system (Figure A.1). Tighten all screws.

For the Mac: Connect the Diamond Pro 930SB Macintosh cable adapter (not included) to the monitor
connector on the Macintosh (Figure B.1). Attach the 15-pin mini D-SUB end of the captive signal cable to
the Diamond Pro 930SB Macintosh cable adapter on the computer (Figure B.1). Tighten all screws.

4. Connect one end of the power cord to the Diamond Pro 930SB monitor and the other end to the power
outlet (Figure C.1).

5. Turn on the monitor (Figure D.1) and the computer.

6. The Windows 95/98/2000/Me/XP INF file for your monitor can be found on the CD-ROM, delivered with the
monitor.

NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual.

Figure A.1

15-pin
mini
D-SUB

Captive Signal Cable

Figure B.1

Mac Adapter
(Not Included)

Captive Signal Cable

Quick Start – continued

6 User’s Manual

Figure C.1

Power Outlet

Power
Cord

Power Button

Figure D.1