MINI Hardtop 2 Door With Connected 2015, Hardtop 4 Door With Connected 2015 Owner's Manual

Download

Page 1

OWNER'S MANUAL.

MINI.

Contents

A-Z

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 2

Page 3

MINI

Owner's Manual for Vehicle

Thank you for choosing a MINI.

The more familiar you are with your vehicle, the better control you will have on the road. We therefore strongly suggest:

Read this Owner's Manual before starting off in your new MINI. Also use the Integrated Owner's Manual in your vehicle. It con‐ tains important information on vehicle operation that will help you make full use of the technical features available in your MINI. The manual also contains information designed to en‐ hance operating reliability and road safety, and to contribute to maintaining the value of your MINI.

Any updates made after the editorial deadline can be found in the appendix of the printed Owner's Handbook for the Vehicle.

Get started now. We wish you driving fun and inspiration with your MINI

The MINI team of BMW AG

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 4

© 2015 Bayerische Motoren Werke Aktiengesellschaft Munich, Germany Reprinting, including excerpts, only with the written consent of BMW AG, Munich. US English II/15, 03 15 490 Printed on environmentally friendly paper, bleached without chlorine, suitable for recycling.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 5

ADDENDUM TO OWNER'S MANUAL

Addendum

We wanted to provide you with some updates and clarifications with respect to the printed MINI Owner's Manual. These updates and clarifications will supersede the materials contained in that document.

1. Where the terms “service center,” “the ser-

vice center,” “your service center,” “service specialist,” or “service” are used in the Owner's Manual, we wanted to clarify that the terms refer to a MINI dealer's service center or another service center or repair shop that employs trained personnel that can perform maintenance and repair work on your vehicle in accordance with MINI specifications.

2. Where the text of the Owner's Manual con-

tains an affirmative instruction to contact a “service center” or “your service center,” we wanted to clarify that MINI recommends that, if you are faced with one of the situations addressed by that text, you contact or seek the assistance of a MINI dealer's service center or another service center or repair shop that employs trained personnel that can perform maintenance and repair work on your vehicle in accordance with MINI specifications.

While MINI, at no cost to you, will pay for repairs required by the limited warranties provided with respect to your vehicle and for maintenance under the Maintenance Program during the applicable warranty and maintenance coverage periods, you are free to elect, both during those periods and thereafter, to have maintenance and repair work provided by other service centers or repair shops.

3. Where the Owner's Manual makes reference

to parts and accessories having been approved by MINI, those references are intended to reflect that those parts and accessories are recommended by MINI. You may elect to use other parts and accessories, but, if you do, we recommend that you make sure

that any such parts and/or accessories are appropriate for use on your vehicle.

4. At page 7, under the warranty section's dis-

cussion of homologation, where it states that you “cannot lodge warranty claims for your vehicle there,” the text should read that you “may not be able to lodge warranty claims for your vehicle there.”

5. At page 7, in the “Parts and Accessories”

section, the sentence beginning “For your own safety, use … ,” should be disregarded and the following the text should be read in lieu thereof: “The manufacturer of your vehicle recommends using genuine MINI parts and accessories.”

In the fifth sentence of that paragraph, the word “cannot” should read “does not.”

6. At page 51, in the “Check and replace safety

belts” section, the text beginning, “This should only be done by your service center …” should be disregarded and the following text should be read in lieu thereof: “MINI recommends having this work performed by a service center as it is important that this safety feature functions properly.”

7. At page 155 under the heading: “Objects in

the area around the pedals” and at page 217 under the heading: “Carpets and floor mats,” the paragraph that begins: “Only use floor mats …” should be disregarded and the following language should be read in lieu thereof: “The manufacturer of your vehicle recommends that you use floor mats that have been identified by it as appropriate for use in your vehicle and that can be properly fixed in place.”

8. At page 162, under the heading: “Have

maintenance carried out,” the sentence beginning, “Have the maintenance carried out …” should be disregarded and the following text should be read in lieu thereof: “MINI recommends that you have the maintenance carried out by your service center.”

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 6

Addendum

9. At page 174, under the heading “Pressure

specifications,” the sentence beginning, “Pressure specifications apply to approved tire sizes …” should be disregarded.

10. At page 181, under the heading: “Moun-

ting,” the paragraph beginning, “Have mounting and balancing …” should be disregarded and the following text should be read in lieu thereof: “BMW recommends that you have mounting and balancing performed by your service center or a tire mounting specialist.”

11. At page 181, under the heading: “Approved

wheels and tires,” the term “Approved” should be disregarded and in lieu thereof, the term “Recommended” should be read in its place. In addition, the text of that section should be disregarded and the following text should be read in lieu thereof:

The manufacturer of your vehicle strongly suggests that you use wheels and tires that have been recommended by the vehicle manufacturer for your vehicle type; otherwise, for example, despite having the same official size ratings, variations can lead to body contact and with it, the risk of severe accidents.

The manufacturer of your vehicle does not evaluate non-recommended wheels and tires to determine if they are suitable for use on your vehicle.

12. At page 186, under the heading: “Snow

Chains,” the paragraph beginning, “Only certain fine-link snow chains …” should be disregarded and the following text should be read in lieu thereof:

Only certain types of fine-link snow chains have been tested by the manufacturer of your vehicle and are determined by the manufacturer of your vehicle to be road safe and are recommended by the manufacturer of your vehicle.

Information about recommended snow chains is available from a service center.

13. At page 188, under the heading “Hood,” the

sentence beginning, “If you are unfamiliar” should be disregarded.

14. At page 192, under the heading: “Engine oil

change,” the text should be disregarded and in lieu thereof should be read as follows:

MINI recommends that you have the oil changed at your MINI dealer's service center or at another service center that has trained personnel that can perform the work in accordance with MINI specifications.

15. At page 195, under the heading: “Service

and Warranty Information Booklet for US Models and Warranty and Service Guide Booklet for Canadian Models,” the second paragraph should be disregarded and the following text read in lieu thereof:

The manufacturer of your vehicle recommends that you have maintenance and repair performed by your MINI dealer's service center or another service center or repair shop that employs trained personnel that can perform maintenance and repair work on your vehicle in accordance with MINI specifications. The manufacturer of your vehicle recommends that you maintain records of all maintenance and repair work performed on your vehicle.

16. At page 207, under the “Battery replace-

ment” section, the text should be disregarded and in lieu thereof the following text should be read:

Use of recommended vehicle batteries

The manufacturer of your vehicle recommends that you use vehicle batteries that it has tested and recommends for use in your vehicle; otherwise the vehicle could be damaged and systems or functions may not be fully available.

After a battery replacement, the manufacturer of your vehicle recommends that you have the battery registered on your vehicle by a service center to ensure that all comfort functions are fully available, and that any

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 7

“check control” messages of these comfort functions are no longer displayed.

Addendum

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 8

Page 9

Contents

The fastest way to find information on a partic‐ ular topic or item is by using the index, refer to page 230.

6 Notes

AT A GLANCE

14 Cockpit 18 Onboard monitor 27 Voice activation system 30 Integrated Owner's Manual in the vehicle

CONTROLS

34 Opening and closing 48 Adjusting 56 Transporting children safely 60 Driving 72 Displays 90 Lights 95 Safety 111 Driving stability control systems 115 Driving comfort 132 Climate control 139 Interior equipment

141 Digital compass

147 Storage compartments

MOBILITY

170 Refueling 172 Fuel 174 Wheels and tires 188 Engine compartment 190 Engine oil 193 Coolant 195 Maintenance 197 Replacing components 209 Breakdown assistance 214 Care

REFERENCE

220 Technical data 225 Appendix 230 Everything from A to Z

DRIVING TIPS

154 Things to remember when driving 157 Loading 161 Saving fuel

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 10

Notes

Using this Owner's Manual

The fastest way to find information on a partic‐ ular topic is by using the index.

An initial overview of the vehicle is provided in the first chapter.

Updates made after the editorial deadline

Any updates made after the editorial deadline can be found in the appendix of the printed Owner's Handbook for Vehicle.

User's manual for Navigation, Entertainment, Communication

The topics Navigation, Entertainment, Commu‐ nication and the short commands of the voice activation system can be retrieved on the Con‐ trol Display via the Integrated Owner's Hand‐ book.

Additional sources of information

Should you have any questions, your service center will be glad to advise you at any time.

Information about MINI, e.g., on technology, is available on the Internet: www.miniusa.com

Symbols

Indicates precautions that must be followed precisely in order to avoid the possibility of personal injury and serious damage to the vehicle.

◄ Marks the end of a specific item of information.

"..." Identifies Control Display texts used to select individual functions.

›...‹ Verbal instructions to use with the voice activation system..

››...‹‹ Identifies the answers generated by the voice activation system.

Refers to measures that can be taken to

help protect the environment.

Symbols on vehicle components

Indicates that you should consult the relevant section of this Owner's Manual for information on a particular part or assembly.

Vehicle features and op‐ tions

This Owner's Manual describes all models and all standard, country-specific and optional equipment that is offered in the model series. Therefore, in this Owner's Manual, we also de‐ scribe and illustrate features that are not avail‐ able in your vehicle, e.g., because of the se‐ lected optional features or the country-specific version.

This also applies to safety-related functions and systems.

The respectively applicable country provisions must be observed when using the respective features and systems.

For any options and equipment not described in this Owner's Handbook, refer to the Supple‐ mentary Owner's Handbooks.

On right-hand drive vehicles, some controls are arranged differently from what is shown in the illustrations.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 11

Notes

Status of the Owner's Manual

Basic information

The manufacturer of your vehicle pursues a policy of constant development that is con‐ ceived to ensure that our vehicles continue to embody the highest quality and safety stan‐ dards. In rare cases, therefore, the features de‐ scribed in this Owner's Manual may differ from those in your vehicle.

Updates made after the editorial deadline

Any updates made after the editorial deadline can be found in the appendix of the printed Owner's Handbook for Vehicle.

Own safety

Manufacturer

The manufacturer of this MINI is Bayerische Motoren Werke Aktionengesellschaft, BMW AG.

Warranty

Your vehicle is technically configured for the operating conditions and registration require‐ ments applying in the country of first delivery homologation. If your vehicle is to be operated in a different country it might be necessary to adapt your vehicle to potentially differing oper‐ ating conditions and permit requirements. If your vehicle does not comply with the homolo‐ gation requirements in a certain country you cannot lodge warranty claims for your vehicle there. Further information can be obtained from your Service Centre.

Maintenance and repairs

Advanced technology, e.g., the use of modern materials and high-performance electronics, requires suitable maintenance and repair work.

Therefore, have this work performed only by a MINI service center or a workshop that works according to the manufacturer's repair proce‐ dures for the MINI with respectively trained personnel.

If work is not carried out properly, there is a danger of subsequent damage and related safety hazards.

Parts and Accessories

For your own safety, it is recommended that you use genuine parts and accessories ap‐ proved by MINI. When you purchase accesso‐ ries tested and approved by MINI and Genuine MINI Parts, you simultaneously acquire the as‐ surance that they have been thoroughly tested by MINI to ensure optimum performance when installed on your vehicle. MINI warrants these parts to be free from defects in material and workmanship. MINI will not accept any liability for damage resulting from installation of parts and accessories not approved by MINI. MINI cannot test every product made by other man‐ ufacturers to verify if it can be used on a MINI safely and without risk to either the vehicle, its operation, or its occupants. Genuine MINI Parts, MINI Accessories and other products approved by MINI, together with professional advice on using these items, are available from all MINI centers. Installation and operation of non-MINI approved accessories such as alarms, radios, amplifiers, radar detectors, wheels, suspension components, brake dust shields, telephones, including operation of any mobile phone from within the vehicle without using an externally mounted antenna, or transceiver equipment, for instance, CBs, walkie-talkies, ham radios or similar accessories, may cause extensive dam‐ age to the vehicle, compromise its safety, inter‐ fere with the vehicle's electrical system or af‐ fect the validity of the MINI Limited Warranty. See your MINI center for additional informa‐ tion. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any automotive repair estab‐

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 12

Notes

lishment or individual using any certified auto‐ motive part.

California Proposition 65 Warning

California laws require us to state the following warning:

Engine exhaust and a wide variety of automo‐ bile components and parts, including compo‐ nents found in the interior furnishings in a vehi‐ cle, contain or emit chemicals known to the State of California to cause cancer and birth de‐ fects and reproductive harm. In addition, cer‐ tain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other repro‐ ductive harm. Battery posts, terminals and re‐ lated accessories contain lead and lead com‐ pounds. Wash your hands after handling. Used engine oil contains chemicals that have caused cancer in laboratory animals. Always protect your skin by washing thoroughly with soap and water.

Service and warranty

We recommend that you read this publication thoroughly. Your vehicle is covered by the fol‐ lowing warranties:

▷ New Vehicle Limited Warranty.

▷ Rust Perforation Limited Warranty.

▷ Federal Emissions System Defect Warranty.

▷ Federal Emissions Performance Warranty.

▷ California Emission Control System Limited

Warranty.

Detailed information about these warranties is listed in the Service and Warranty Information Booklet for US models or in the Warranty and Service Guide Booklet for Canadian models.

Your vehicle has been specifically adapted and designed to meet the particular operating con‐ ditions and homologation requirements in your country and continental region in order to de‐ liver the full driving pleasure while the vehicle is

operated under those conditions. If you wish to operate your vehicle in another country or re‐ gion, you may be required to adapt your vehi‐ cle to meet different prevailing operating con‐ ditions and homologation requirements. You should also be aware of any applicable war‐ ranty limitations or exclusions for such country or region. In such case, please contact Cus‐ tomer Relations for further information.

Maintenance

Maintain the vehicle regularly to sustain the road safety, operational reliability and the New Vehicle Limited Warranty.

Specifications for required maintenance meas‐ ures:

▷ MINI Maintenance system

▷ Service and Warranty Information Booklet

for US models

▷ Warranty and Service Guide Booklet for

Canadian models

If the vehicle is not maintained according to these specifications, this could result in serious damage to the vehicle. Such damage is not covered by the MINI New Vehicle Limited War‐ ranty.

Data memory

Many electronic components on your vehicle are equipped with data memories that tempo‐ rarily or permanently store technical informa‐ tion about the condition of the vehicle, events and faults. This technical information generally records the state of a component, a module, a system or the environment:

▷ Operating mode of system components, fill

levels for instance.

▷ Status messages for the vehicle and from its

individual components, e.g., wheel rotation speed/vehicle speed, deceleration, trans‐ verse acceleration.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 13

Notes

▷ Malfunctions and faults in important system

components, e.g., lights and brakes.

▷ Responses by the vehicle to special situa‐

tions such as airbag deployment or engag‐ ing the stability control system.

▷ Ambient conditions, such as temperature.

This data is purely technical in nature and is used to detect and correct faults and to opti‐ mize vehicle functions. Motion profiles over routes traveled cannot be created from this data. When service offerings are used, e.g., re‐ pair services, service processes, warranty claims, quality assurance, this technical infor‐ mation can be read out from the event and fault memories by the service personnel, in‐ cluding the manufacturer, using special diag‐ nostic tools. You can obtain further information there if you need it. After an error is corrected, the information in the fault memory is deleted or overwritten on a continuous basis.

With the vehicle in use there are situations where you can associate these technical data with individuals if combined with other infor‐ mation, e.g., an accident report, damage to the vehicle, eye witness accounts — possibly with the assistance of an expert.

Additional functions that are contractually agreed with the customer - such as vehicle emergency locating - you can transmit certain vehicle data from the vehicle.

▷ How various systems in your vehicle were

operating.

▷ Whether or not the driver and passenger

safety belts were fastened.

▷ How far, if at all, the driver was depressing

the accelerator and/or brake pedal.

▷ How fast the vehicle was traveling.

These data can help provide a better under‐ standing of the circumstances in which crashes and injuries occur.

EDR data are recorded by your vehicle only if a nontrivial crash situation occurs; no data are re‐ corded by the EDR under normal driving condi‐ tions and no personal data, e.g., name, gender, age, and crash location, are recorded.

However, other parties, such as law enforce‐ ment, could combine the EDR data with the type of personally identifying data routinely ac‐ quired during a crash investigation.

To read data recorded by an EDR, special equipment is required, and access to the vehi‐ cle or the EDR is needed. In addition to the ve‐ hicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.

Vehicle identification number

Event Data Recorder EDR

This vehicle is equipped with an event data re‐ corder EDR. The main purpose of an EDR is to record, in certain crash or near crash-like situa‐ tions, such as an air bag deployment or hitting a road obstacle, data that will assist in under‐ standing how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.

The EDR in this vehicle is designed to record such data as:

Online Edition for Part no. 01 40 2 961 168 - II/15

The vehicle identification number can be found in the engine compartment.

Page 14

Notes

The vehicle identification number can also be found behind the windshield.

Reporting safety defects

For US customers

The following only applies to vehicles owned and operated in the US.

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration NHTSA, in addition to notifying MINI of North America, LLC, P.O. Box 1227, Westwood, New Jersey 07675-1227, Telephone 1-800-831-1117.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.

However, NHTSA cannot become involved in individual problems between you, your dealer, or MINI of North America, LLC.

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safe‐ rcar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safe‐ rcar.gov

For Canadian customers

Canadian customers who wish to report a safety-related defect to Transport Canada, De‐ fect Investigations and Recalls, may call the toll-free hotline 1-800-333-0510. You can also obtain other information about motor vehicle safety from http://www.tc.gc.ca/roadsafety.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 15

Notes

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 16

WATCH ME.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 17

AT A GLANCE

CONTROLS

DRIVING TIPS

MOBILITY

REFERENCE

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 18

AT A GLANCE

Cockpit

Vehicle features and op‐ tions

This chapter describes all standard, countryspecific and optional features offered with the series. It also describes features that are not

necessarily available in your car, e. g., due to the selected options or country versions. This also applies to safety-related functions and sys‐ tems. The respectively applicable country provi‐ sions must be observed when using the respec‐ tive features and systems.

All around the steering wheel

1 Power windows 45

2 Exterior mirror operation 53

3 Central locking system 40

4 Lights

Front fog lights 93

Parking lights 90

Low beams 90

Online Edition for Part no. 01 40 2 961 168 - II/15

Automatic headlight control 91

Daytime running lights 91

Corner-illuminating lights 92

High-beam Assistant 92

Instrument lighting 93

5 Steering wheel buttons, left

Page 19

Cockpit

AT A GLANCE

Cruise control on/off, inter‐ rupt 115

Cruise control on/off, inter‐ rupt 121

Store speed 115, 121

Resume speed 117, 122

Set speed 117, 121

Reduce distance 121

Increase distance 115

6 Steering column stalk, left

Turn signal 65

High beams, head‐ light flasher 65

High-beam Assistant 92

Cleaning windows 67

Rear window wiper 67

Cleaning rear window 67

9 Steering wheel buttons, right

Voice activation 27

Telephone

Confirm the selection 81

Move selection up 81

Move selection down 81

Increase volume

Reduce volume

Roadside parking lights 90

Computer 81

7 Instrument cluster 72

8 Steering column stalk, right

Windshield wipers 65

Rain sensor 66

Online Edition for Part no. 01 40 2 961 168 - II/15

10 Horn

11 Adjust the steering wheel 55

12 Unlock hood 188

Page 20

AT A GLANCE

Cockpit

All around the center console

1 Hazard warning system 209

Intelligent Safety 103

2 Control Display 18

3 Radio/Multimedia

4 Glove compartment 147

5 Climate control 132

6 PDC Park Distance Control 123

Rearview camera 125

Parking assistant 127

Auto Start/Stop function 62

Start/stop the engine and switch the ignition on/off 63

DSC Dynamic Stability Con‐ trol 111

Head-up Display 86

7 Steptronic transmission selector lever 68

Manual transmission selector lever 68

8 Controller with buttons 19

9 Parking brake 64

10 Driving Dynamics Control 113

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 21

All around the roofliner

Cockpit

AT A GLANCE

1 Emergency Request

2 Indicator lamp, front-seat passen‐

ger airbag 97

3 Reading lights 94

4 Ambient light 94

5 Glass sunroof 46

6 Interior lights 93

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 22

AT A GLANCE

Onboard monitor

Vehicle features and op‐ tions

This chapter describes all standard, countryspecific and optional features offered with the series. It also describes features that are not necessarily available in your car, e. g., due to the selected options or country versions. This also applies to safety-related functions and sys‐ tems. The respectively applicable country provi‐ sions must be observed when using the respec‐ tive features and systems.

The concept

The onboard monitor combines the functions of a multitude of switches. Thus, these func‐ tions can be operated from a central location.

Using the onboard monitor during a trip

To avoid becoming distracted and posing an unnecessary hazard to your vehicle's occu‐ pants and to other traffic, never attempt to use the controls or enter information unless traffic and road conditions allow it.◀

Control elements at a glance

Control elements

1 Control Display

2 Controller with buttons and, depending on

the equipment version, with touchpad

Control Display

Hints

▷ To clean the Control Display, follow the care

instructions.

▷ Do not place objects close to the Control

Display; otherwise, the Control Display can be damaged.

▷ In the case of very high temperatures on

the Control Display, e.g. due to intense so‐ lar radiation, the brightness may be re‐ duced down to complete deactivation. Once the temperature is reduced, e.g. through shadow or climate control system, the normal functions are re-established.

Switching on

Switch on the ignition.

2. Press the controller.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 23

Onboard monitor

AT A GLANCE

Switch off

2. "Turn off control display"

Press button.

Controller with navigation system

The buttons can be used to open the menus di‐ rectly. The controller can be used to select menu items and enter the settings.

Some functions of the onboard monitor can be operated using the touchpad on the controller:

Turn.

3. Move in four directions.

Buttons on controller

Press button Function

MENU Open the main menu.

RADIO Opens the Radio menu.

MEDIA Opens the Multimedia menu.

NAV Opens the Navigation menu.

TEL Opens the phone menu.

BACK Displays the previous panel.

OPTION Opens the Options menu.

2. Press.

Controller without navigation system

The buttons can be used to open the menus di‐ rectly. The controller can be used to select menu items and enter the settings.

Turn.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 24

AT A GLANCE

2. Press.

3. Move in two directions.

Buttons on controller

Onboard monitor

The main menu is displayed.

All onboard monitor functions can be called up via the main menu.

Selecting menu items

Highlighted menu items can be selected.

Turn the controller until the desired menu item is highlighted.

Press button Function

MENU Open the main menu.

Audio Open audio menu last listened to,

switch between audio menus.

TEL Opens the phone menu.

BACK Open previous panel.

OPTION Opens the Options menu.

Operating concept

Opening the main menu

Press button.

Online Edition for Part no. 01 40 2 961 168 - II/15

2. Press the controller.

Menu items in the Owner's Manual

In the Owner's Manual, menu items that can be selected are set in quotation marks, e.g., "Settings".

Changing between panels

After a menu item is selected, e.g., "Radio", a new panel is displayed. Panels can overlap.

▷ Move the controller to the left.

Closes current display and shows previous display.

Reopens previous display by pressing BACK button. In this case, the current panel is not closed.

Page 25

Onboard monitor

AT A GLANCE

▷ Move the controller to the right.

Opens new display on top of previous screen.

Arrows pointing to the left or right indicate that additional panels can be opened.

Display of an opened menu

When selecting a menu, it generally opens with the panel that was last selected in that menu. To display the first panel of a menu:

▷ Move the controller to the left repeatedly

until the first panel is displayed.

▷ Press the menu button on the controller

twice.

Opening the Options menu

Press button.

The "Options" menu is displayed.

Options menu

The "Options" menu consists of various areas:

▷ Screen settings, e.g., "Split screen".

This area remains unchanged.

▷ Control options for the selected main

menu, e.g., for "Radio".

▷ If applicable, further operating options for

the selected menu, e.g., "Store station".

Changing settings

1. Select a field.

2. Turn the controller until the desired setting

is displayed.

3. Press the controller.

Activating/deactivating the functions

Several menu items are preceded by a check‐ box. It indicates whether the function is acti‐ vated or deactivated. Selecting the menu item activates or deactivates the function.

Function is activated.

Function is deactivated.

Additional options: move the controller to the right repeatedly until the "Options" menu is displayed.

Online Edition for Part no. 01 40 2 961 168 - II/15

Touchpad

Some functions of the onboard monitor can be operated using the touchpad on the controller:

Selecting functions

On the Control Display:

"Settings"

Page 26

AT A GLANCE

Onboard monitor

2. "Touchpad"

3. Select the desired function.

▷ "Speller": enter letters and numbers.

▷ "Interactive map": viewing the interac‐

tive map.

▷ "Audio feedback": pronounces entered

letters and numbers.

Entering letters and numbers

Entering letters requires some practice at the beginning. When entering, pay attention to the following:

▷ For the input of upper/lower case letters

and numbers, it may be necessary to switch via the controller to the corresponding In‐ put mode, refer to page 25, e.g. when the spelling of upper and lower case letters is identical.

▷ Enter characters as they are displayed on

the Control Display.

▷ Always enter associated characters, such as

accents or periods so that the letter can be clearly recognized. Possible input depends on the set language. Where necessary, en‐ ter special characters via the controller.

▷ To delete a character, slide to the left on

the touchpad.

▷ To enter a blank space, slide to the right in

the center of the touchpad.

▷ To enter a hyphen, slide to the right in the

upper area of the touchpad.

▷ To enter an underscore, swipe to the right

in the lower area of the touchpad.

Operating the interactive map

The interactive map in the navigation system can be moved via the touchpad.

Function Controls

Interactive map. Swipe into respective

direction.

Enlarge/shrink in‐ teractive map.

Display menu. Tap once.

Drag in or out on the touchpad with fingers.

Changing settings

You may change control display settings via touchpad. Swipe left or right accordingly.

Example: setting the clock

Setting the clock

On the Control Display:

1. Press button. The main menu is dis‐

played.

2. Turn the controller until "Settings" is

highlighted, and then press the controller.

3. If necessary, move the controller to the left

to display "Time/Date".

4. Turn the controller until "Time/Date" is

highlighted, and then press the controller.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 27

Onboard monitor

AT A GLANCE

5. Turn the controller until "Time:" is high‐

lighted, and then press the controller.

6. Turn the controller to set the hours and

press the controller.

7. Turn the controller to set the minutes and

press the controller.

Status information

Status field

The following information is displayed in the status field at the top right:

▷ Time.

▷ Current entertainment source.

▷ Sound output, on/off.

▷ Wireless network reception strength.

▷ Phone status.

▷ Traffic bulletin reception.

Status field symbols

The symbols are grouped as follows.

Telephone symbols

Symbol Meaning

Incoming or outgoing call.

Missed call.

Wireless network reception strength.

Symbol flashes: network search.

Wireless network is not available.

Bluetooth is switched on.

Roaming is active.

Text message was received.

Check the SIM card.

SIM card is blocked.

SIM card is missing.

Enter PIN.

Entertainment symbols

Symbol Meaning

DVD changer.

Music collection.

Gracenote® database.

AUX-IN port.

USB audio interface.

Mobile phone audio interface.

Radio symbols

Symbol Meaning

HD Radio station is being received.

Satellite radio is switched on.

Online Edition for Part no. 01 40 2 961 168 - II/15

Additional symbols

Symbol Meaning

Spoken instructions are turned off.

Page 28

AT A GLANCE

Onboard monitor

Split screen

General information

Additional information can be displayed on the right side of the split screen, e.g., information from the on-board comupter.

In the divided screen view, the so-called split screen, this information remains visible even when you change to another menu.

Switching the split screen on and off

On the Control Display:

1. Press button.

2. "Split screen"

Selecting the display

On the Control Display:

1. Press button.

2. "Split screen"

3. Move the controller until the split screen is

selected.

4. Press the controller or select "Split screen

content".

5. Select the desired menu item.

Programmable memory buttons

General information

The onboard monitor functions can be stored on the programmable memory buttons and called up directly, e.g., radio stations, naviga‐ tion destinations, phone numbers and menu entries.

Settings are stored for the profile currently in use.

Saving a function

Highlight function via the onboard monitor.

Running a function

This means, e.g., that the number is dialed when a phone number is selected.

Displaying the button assignment

Touch buttons with bare fingers. Do not wear gloves or use objects.

The key assignment is displayed at top edge of screen.

Press and hold the desired button,

until a signal sounds.

Press button.

The function will work immediately.

Deleting the button assignments

Press buttons 1 and 6 simultaneously for

approx. five seconds.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 29

Onboard monitor

AT A GLANCE

2. "OK"

Deleting personal in the vehicle

The concept

Depending on the usage, the vehicle saves per‐ sonal data, such as stored radio stations. These personal data can be permanently deleted via the onboard monitor.

General information

Depending on the equipment package, the fol‐ lowing data can be deleted:

▷ Personal Profile settings.

▷ Stored radio stations.

▷ Stored Favorites buttons.

▷ Travel and computer information.

▷ Music collection.

▷ Navigation, e.g. stored destinations.

▷ Phone book.

▷ Online data, e.g. Favorites, cookies.

▷ Voice notes.

▷ Login accounts.

Altogether, the deletion of the data can take up to 30 minutes.

Functional requirement

Data can only be deleted while stationary.

Deleting data

Heed and follow the instructions on the Control Display.

Switch on the ignition.

2. "Settings"

3. Open "Options".

4. "Delete all personal data"

5. "Continue"

6. "OK"

Entering letters and numbers

General information

On the Control Display:

1. Turn the controller: select letters or num‐

bers.

2. Select additional letters or numbers if

needed.

3. "OK": confirm the entry.

Symbol Function

Press the controller: delete the letter

or number.

Press the controller for an extended

period: delete all letters or numbers.

Switching between cases, letters and numbers

Depending on the menu, you can switch be‐ tween entering upper and lower case, letters and numbers:

Symbol Function

Enter the letters.

Enter the numbers.

or Tip controller up.

Without navigation system

Select the symbol.

Entry comparison

Entering names and addresses: choice is nar‐ rowed down with every letter entered and let‐ ters may be added automatically.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 30

AT A GLANCE

Entries are continuously compared with data stored in the vehicle.

▷ Only those letters are offered during input

for which data is available.

▷ Target search: names of locations may be

entered in languages available through Control Display.

Onboard monitor

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 31

Voice activation system

AT A GLANCE

Vehicle features and op‐ tions

The concept

▷ Most functions displayed on the Control

Display can be operated by voice com‐ mands via the voice activation system. The system supports you with announcements during input.

▷ Functions that can only be used when the

vehicle is stationary cannot be used via the voice activation system.

▷ The system uses a special microphone on

the driver's side.

▷ ›...‹ Verbal instructions in the Owner's

Manual to use with the voice activation sys‐ tem.

Requirements

Via the Control Display, set a language that is also supported by the voice activation system so that the spoken commands can be identi‐ fied.

Set the language, refer to page 85.

Using voice activation

Activating the voice activation system

2. Wait for the signal.

3. Say the command.

This symbol in the instrument cluster indi‐

cates that the voice activation system is active.

If no other commands are available, operate the function via the onboard monitor.

Press button on the steering wheel.

A command that is recognized by the voice activation system is announced and dis‐ played in the instrument cluster.

Terminating the voice activation system

Briefly press the button on the steering wheel or ›Cancel‹.

Possible commands

Most menu items on the Control Display can be voiced as commands.

The available commands depend on the menu that is currently displayed on the Control Dis‐ play.

There are short commands for many functions.

You may select lists such as phone lists via voice activation. Read these lists out loud ex‐ actly as they show in the respective list.

Having possible commands read aloud

You can have available commands read out loud for you: ›Voice commands‹

E. g. if the "Settings" menu is displayed, the commands for the settings are read out loud.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 32

AT A GLANCE

Voice activation system

Executing functions using short commands

Execute functions on the main menu via short commands. It almost doesn't matter which menu item is selected, e.g., ›Vehicle status‹.

Help dialog for the voice activation system

Calling up help dialog: ›Help‹

Additional commands for the help dialog:

▷ ›Help with examples‹: announces informa‐

tion about the current operating options and the most important commands for them.

▷ ›Help with voice activation‹: information

about the principle of operation for the voice activation system is announced.

One example: open the tone settings

Via the main menu

The commands of the menu items are spoken just as they are selected via the controller.

Turn on the Entertainment sound output if

needed.

3. ›Radio‹

4. ›Tone‹

Press button on the steering wheel.

Setting the voice dialog

Set system to standard dialog or use a short version.

The short version of the voice dialog plays back short messages in abbreviated form.

On the Control Display:

1. "Settings"

2. "Language/Units"

3. "Speech type:"

4. Select setting.

Adjusting the volume

Turn the volume button while giving an instruc‐ tion until the desired volume is set.

▷ The volume remains constant even if the

volume of other audio sources is changed.

▷ The volume is stored for the profile cur‐

rently in use.

Hints on Emergency Re‐ quests

Do not use the voice activation system to ini‐ tiate an Emergency Request. In stressful situa‐ tions, the voice and vocal pitch can change. This can unnecessarily delay the establishment of a phone connection.

Via short command

The desired tone settings can also be started via a short command.

Turn on the Entertainment sound output if

needed.

3. ›Tone‹

Press button on the steering wheel.

Online Edition for Part no. 01 40 2 961 168 - II/15

Environmental condi‐ tions

▷ Say the commands, numbers, and letters

smoothly and with normal volume, empha‐ sis, and speed.

▷ Always say commands in the language of

the voice activation system.

▷ Keep the doors, windows, and glass sun‐

roof closed to prevent noise interference.

Page 33

Voice activation system

▷ Avoid making other noise in the vehicle

while speaking.

AT A GLANCE

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 34

AT A GLANCE

Integrated Owner's Manual in the vehicle

Vehicle features and op‐ tions

Integrated Owner's Manual in the vehicle

The Integrated Owner's Manual can be dis‐ played on the Control Display. It specifically de‐ scribes features and functions found in the ve‐ hicle.

Components of the Integrated Owner's Manual

The Integrated Owner's Manual consists of three parts, which offer various levels of infor‐ mation or possible access.

Quick Reference Guide

The Quick Reference Guide provides informa‐ tion how to operate the car, how to use basic vehicle functions or what to do in case of a breakdown. This information can also be dis‐ played while driving.

Search by images

Image search provides information and de‐ scriptions. This is helpful when the terminology for a feature is not at hand.

Owner's Manual

Search for information and descriptions by en‐ tering terms selected from the index.

Select components

2. Turn the controller: open "Vehicle info".

3. Press the controller.

4. Selecting desired range:

Press button.

▷ "Quick reference"

▷ "Search by pictures"

▷ "Owner's Manual"

Leafing through the Owner's Manual

Page by page with link access

Turn the controller until the next or previous page is displayed.

Page by page without link access

Scroll through the pages directly while skipping the links.

Highlight the symbol once. Now simply press the controller to browse from page to page.

Scroll back.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 35

Integrated Owner's Manual in the vehicle

AT A GLANCE

Scroll forward.

Context help - Owner's Manual to the temporarily selected function

You may open the relevant information di‐ rectly.

Opening via the onboard monitor

To move directly from the application on the Control Display to the options menu:

2. "Display Owner's Manual"

Press button or move the controller to the right repeatedly until the "Options" menu is displayed.

Opening when a Check Control message is displayed

Directly from the Check Control message on the Control Display:

"Display Owner's Manual"

Changing between a function and the Owner's Manual

To switch from a function, e. g., radio, to the Owner's Manual on the Control Display and to alternate between the two displays:

To alternate permanently between the last dis‐ played function and the Owner's Manual re‐ peat steps 4 & 5. Opens a new display every time.

Programmable memory buttons

General information

The Owner's Manual can be stored on the pro‐ grammable memory buttons and called up di‐ rectly.

Storing

Select "Owner's Manual" via the onboard

monitor.

Press and hold the desired button,

until a signal sounds.

Executing

Press button.

The Owner's Manual is displayed im‐

mediately.

1. Press button or move the controller to

the right repeatedly until the "Options" menu is displayed.

2. "Display Owner's Manual"

3. Select the desired page in the Owner's

Manual.

Press button again to return to last

displayed function.

Press button to return to the page of

the Owner's Manual displayed last.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 36

HANDLE ME.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 37

AT A GLANCE

CONTROLS

DRIVING TIPS

MOBILITY

REFERENCE

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 38

CONTROLS

Opening and closing

Vehicle features and op‐ tions

Remote control/key

General information

The vehicle is supplied with two remote con‐ trols with integrated key.

Every remote control holds a replaceable bat‐ tery.

You may set the key functions depending on the optional features and country-specific ver‐ sion. For Settings, refer to page 42.

The vehicle stores personal settings for every remote control. Personal Profile, refer to page 35.

The remote controls hold information on re‐ quired maintenance. For service data, refer to page 195.

Overview

1 Unlocking

2 Locking

3 Unlock the tailgate

4 Panic mode

Integrated key

Press button, arrow 1, and remove the key, ar‐ row 2.

The integrated key fits the driver's door lock.

Replacing the battery

Remove integrated key from remote con‐

trol.

2. Slide the key into the opening and raise the

cover, arrow.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 39

Opening and closing

CONTROLS

The battery compartment is accessible.

3. Slide the key in the cover of the battery

compartment and raise the cover, arrow.

4. Insert a battery of the same type with the

positive side facing up.

5. Insert lid and cover.

Take the used battery to a recycling center or to your service center.

New remote controls

New remote controls are available from the service center.

Loss of the remote controls

Lost remote controls can be disabled by your service center.

Emergency detection of remote control

It is possible to switch on the ignition or start the engine in situations such as the following:

▷ Interference of radio transmission to re‐

mote control by external sources e.g., by radio masts.

▷ Empty battery in remote control.

▷ Interference from radio transmissions

through mobile devices in close proximity to remote control.

▷ Interference of radio transmission by

charger while charging items such as mo‐ bile devices in the vehicle.

A Check Control message is displayed if an at‐ tempt is made to switch on the ignition or start the engine.

Starting the engine via emergency detection of the remote control

Steptronic transmission: if a corresponding Check Control message appears, hold the re‐ mote control, as shown, against the marked area on the steering column and press the Start/Stop button within 10 seconds while pressing the brake.

Manual transmission: if a corresponding Check Control message appears, hold the remote con‐ trol, as shown, against the marked area on the steering column and press the Start/Stop but‐ ton within 10 seconds while pressing the clutch.

Personal Profile

The concept

Personal Profile provides three profiles, using which personal vehicle settings can be stored. Every remote control has one of these profiles assigned.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 40

CONTROLS

Opening and closing

If the vehicle is unlocked using a remote con‐ trol, the assigned personal profile will be acti‐ vated. All settings stored in the profile are auto‐ matically applied.

If several drivers use their own remote control, the vehicle will adjust the personal settings dur‐ ing unlocking. These settings are also restored, if the vehicle has been used in the meantime by a person with a different remote control.

Changes to the settings are automatically saved in the personal profile.

Three personal profiles and a guest profile can be created.

Adjusting

The settings for the following systems and func‐ tions are saved in the active profile. The scope of storable settings is country- and equipmentdependable.

▷ Unlocking and locking.

▷ Lights.

▷ Radio.

▷ Instrument cluster.

▷ Programmable memory buttons.

▷ Volumes, tone.

▷ Control Display.

▷ Climate control.

▷ Navigation.

▷ Park Distance Control PDC.

▷ Rearview camera

▷ Head-up Display.

▷ Driving Dynamics Control.

▷ Cruise control.

▷ Intelligent Safety.

Profile management

Opening profiles

Regardless of the remote control in use a differ‐ ent profile may be activated.

1. "Settings"

2. "Profiles"

3. Select a profile.

▷ All settings stored in the called-up profile

are automatically applied.

▷ The called-up profile is assigned to the re‐

mote control being used at the time.

▷ If the profile is already assigned to a differ‐

ent remote control, this profile will apply to both remote controls. It cannot be differen‐ tiated anymore between the settings for the two remote controls.

Renaming profiles

A personal name can be assigned to every pro‐ file to avoid confusion between the profiles.

"Settings"

2. "Profiles"

The current profile is selected.

3. "Options"

4. "Rename current profile"

Resetting profiles

The settings of the active profile are reset to their default values.

"Settings"

2. "Profiles"

The current profile is selected.

3. Open "Options".

4. "Reset current profile"

Exporting profiles

Most settings of the active profile can be ex‐ ported.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 41

Opening and closing

CONTROLS

This can be helpful for securing and retrieving personal settings, before delivering the vehicle to a workshop, e.g. Profiles can be taken to an‐ other vehicle equipped with the Personal Pro‐ file function.

Export is made via the USB port to a USB de‐ vice.

Popular file systems for USB devices are sup‐ ported. FAT32 and exFAT are the recom‐ mended formats for profile export. Other for‐ mats may not support the export.

1. "Settings"

2. "Profiles"

3. "Export profile"

4. "USB device"

Importing profiles

Profiles stored on a USB device can be im‐ ported via the USB interface.

Existing settings are overwritten with the im‐ ported profile.

"Settings"

2. "Profiles"

3. "Import profile"

4. "USB device"

Using the guest profile

The guest profile is for individual settings that are saved in none of the three personal profiles.

This can be useful for drivers who are using the vehicle temporarily and do not have their own profile.

"Settings"

2. "Profiles"

3. "Guest"

4. Adjust the settings.

The guest profile cannot be renamed. It is not assigned to the current remote control.

Display profile list during start

The profile list can be displayed during each start to select the desired profile.

1. "Settings"

2. "Profiles"

3. Open "Options".

4. "Display user list at startup"

Using the remote con‐ trol

Note

Take the remote control with you

People or animals left unattended in a parked vehicle can lock the doors from the in‐ side. Always take the remote control with you when leaving the vehicle so that the vehicle can then be opened from the outside.◀

Unlocking

Press button on the remote control.

▷ The vehicle is unlocked.

▷ Interior lamps and courtesy lamps are acti‐

vated. This function is not available, if the interior lamps were switched off manually.

▷ The welcome lamps are switched on, if this

function was activated.

▷ Exterior mirrors folded through convenient

closing are folded open.

On 3-door models:

Press button on the remote control

twice in direct succession.

When the door is opened, the window is low‐ ered more to make it easier to enter the vehi‐ cle.

You can set how the vehicle is to be unlocked. Create the settings, refer to page 42.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 42

CONTROLS

Opening and closing

The alarm system, refer to page 43, is dis‐ armed.

Convenient opening

Press and hold this button on the re‐ mote control after unlocking.

The windows and the glass sunroof are opened, as long as the button on the remote control is pressed.

Locking

Locking from the outside

Do not lock the vehicle from the outside with people inside the car, as the vehicle can‐ not be unlocked from inside without special knowledge.◀

The driver's door must be closed.

Press button on the remote control.

The alarm system, refer to page 43, is armed.

If the vehicle horn honks twice when you lock the car, this means that the engine or ignition is still switched on. In this case, the engine or ig‐ nition must be switched off by means of the Start/Stop button.

Switching on interior lights and courtesy lights

Press button on the remote control with the vehicle locked.

Panic mode

You can trigger the alarm system if you find yourself in a dangerous situation.

Press button on the remote control for at least 3 seconds.

To switch off the alarm: press any button.

Unlock the tailgate

Press button on the remote control for approx. 1 second.

The tailgate opens slightly, regardless of whether the vehicle was previously locked or unlocked.

Depending on the features and the country version, it is also possible to have door un‐ locked. Create the settings, refer to page 42.

If the doors were not unlocked, the tailgate is locked again as soon as it closes.

Do not place the remote control in the cargo area

Take the remote control with you and do not leave it in the cargo area; otherwise, the re‐ mote control is locked inside the vehicle when the tailgate is closed.◀

Provide edge protection

Sharp objects or those with edges can hit the rear window while driving and damage the heat conductors of the rear window. Provide edge protection.◀

This function is not available, if the interior lamps were switched off manually.

If the button is pressed within 10 seconds of when the vehicle was locked Interior motion sensor and tilt alarm sensor of the anti-theft warning system, refer to page 44, are turned off. After locking, wait 10 seconds before press‐ ing the button again.

Online Edition for Part no. 01 40 2 961 168 - II/15

Malfunction

Remote control detection by the vehicle can among others be malfunctioning under the fol‐ lowing circumstances:

▷ The battery of the remote control is dis‐

charged. Replace the battery, refer to page 34.

▷ Interference of the radio connection from

transmission towers or other equipment with high transmit power.

Page 43

Opening and closing

CONTROLS

▷ Shielding of the remote control due to

metal objects.

▷ Interference of the radio connection from

mobile phones or other electronic devices in direct proximity.

Do not transport the remote control together with metal objects or electronic devices.

In the case of a malfunction, unlock and lock the vehicle using the integrated key, refer to page 39.

For US owners only

The transmitter and receiver units comply with part 15 of the FCC/Federal Communication Commission regulations. Operation is governed by the following:

FCC ID:

▷ LX8766S.

▷ LX8766E.

▷ LX8CAS.

▷ LX8CAS2.

▷ MYTCAS4.

Compliance statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

▷ This device may not cause harmful interfer‐

ence, and

▷ this device must accept any interference re‐

ceived, including interference that may cause undesired operation.

Any unauthorized modifications or changes to these devices could void the user's authority to operate this equipment.

Without remote control

From the outside

Locking from the outside

Do not lock the vehicle from the outside with people inside the car, as the vehicle can‐ not be unlocked from inside without special knowledge.◀

Remove the key before pulling the door

handle

Before pulling the outside door handle, remove the key to avoid damaging the paintwork and the key.◀

Unlock or lock the driver's door via the door lock using the integrated key, refer to page 34. The other doors must be unlocked or locked from the inside.

To do this, unlock the lid from below with the integrated key, arrow, and remove.

Alarm system

The alarm system is not armed if the vehicle is locked with the integrated key.

The alarm system is triggered when the door is opened, if the vehicle was unlocked via the door lock. In order to terminate this alarm, un‐ lock vehicle with the remote control or switch on the ignition, if needed, through emergency detection of the remote control.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 44

CONTROLS

Opening and closing

From the inside

Locking and unlocking

Press button.

Vehicle is locked.

Press button.

The vehicle is unlocked.

Pressing the buttons for the central locking sys‐ tem locks and unlocks the doors and the tail‐ gate when the front doors are closed, but they are not secured against theft.

The fuel filler flap remains unlocked.

In the event of a severe accident, the vehicle is automatically unlocked. The hazard warning system and interior lights come on.

Unlocking and opening

Either unlock the doors together using the cen‐ tral locking system buttons and then pull the door handle above the armrest or pull the door handle on the door to open the door. The other doors remain locked.

Do not place the remote control in the cargo area

Take the remote control with you and do not leave it in the cargo area; otherwise, the re‐ mote control is locked inside the vehicle when the tailgate is closed.◀

Provide edge protection

Sharp objects or those with edges can hit the rear window while driving and damage the heat conductors of the rear window. Provide edge protection.◀

Opening

When the tailgate is opened, make sure there is sufficient clearance to prevent damage.

▷ Unlock the vehicle and press the button on

the tailgate.

▷ Press button on the remote control

for approx. 1 second.

As the case may be, the doors are also un‐ locked. Unlocking with the remote control, refer to page 38.

The tailgate is unlocked and can be swung up‐ ward.

Tailgate

Hints

Keep the closing path clear

Make sure that the closing path of the

tailgate is clear; otherwise, injuries may result.◀

Online Edition for Part no. 01 40 2 961 168 - II/15

Opening from the inside

With the vehicle is stationary, press the button in the driver's footwell.

Page 45

Opening and closing

CONTROLS

Closing

Recessed grips on the inside trim of the tailgate can be used to conveniently pull down the tail‐ gate.

Comfort Access

The concept

The vehicle can be accessed without activating the remote control.

All you need to do is to have the remote control with you, such as in your pants pocket.

The vehicle automatically detects the remote control when it is in close proximity or in the car's interior.

Comfort Access supports the following func‐ tions:

▷ Unlocking/locking of the vehicle.

▷ Convenient closing.

▷ Separate unlocking of the tailgate.

▷ Start the engine.

Functional requirements

▷ There are no sources of interference

nearby.

▷ To lock the vehicle, the remote control

must be located outside of the vehicle.

▷ The next unlocking and locking cycle is not

possible until after approx. 2 seconds.

▷ The engine can only be started if the re‐

mote control is in the vehicle.

Unlocking

On the driver's or front passenger's door han‐ dle, press the button, arrow.

This corresponds to pressing the remote control button:

Locking

On the driver's or front passenger's door han‐ dle, press the button, arrow.

This corresponds to pressing the remote control button:

To save battery power, ensure that all power consumers are turned off, before locking the vehicle.

Convenient closing

Monitor closing

Monitor closing to ensure that no one be‐

comes trapped.◀

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 46

CONTROLS

Press and hold down the handle of the driver or the front seat passenger.

This corresponds to pressing the remote control button:

In addition to locking, the windows and glass sunroof will be closed.

Opening and closing

Unlock the tailgate

Press button on tailgate's exterior.

This corresponds to pressing the remote control button:

The situation of the doors does not change.

Do not place the remote control in the cargo area

Take the remote control with you and do not leave it in the cargo area; otherwise, the re‐ mote control is locked inside the vehicle when the tailgate is closed.◀

Malfunction

Remote control detection by the vehicle can among others be malfunctioning under the fol‐ lowing circumstances:

▷ The battery of the remote control is dis‐

charged. Replace the battery, refer to page 34.

▷ Interference of the radio connection from

transmission towers or other equipment with high transmit power.

▷ Shielding of the remote control due to

metal objects.

▷ Interference of the radio connection from

mobile phones or other electronic devices in direct proximity.

Do not transport the remote control together with metal objects or electronic devices.

In the case of a malfunction, unlock and lock the vehicle using the buttons of the remote control or using the integrated key, refer to page 39.

Adjusting

Unlocking

The settings are saved in the active profile. Per‐ sonal Profile, refer to page 35.

Doors

"Settings"

2. "Doors/key"

3. Select the symbol.

4. Select the desired function.

▷ "Driver's door only"

Only the driver's door and the fuel filler flap are unlocked. Pressing again un‐ locks the entire vehicle.

▷ "All doors"

The entire vehicle is unlocked.

▷ On 3-door models:

"Comfort access"

The entire vehicle is unlocked.

If the remote control button is pressed twice directly consecutively, the win‐ dow is lowered more when the door is opened next.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 47

Opening and closing

CONTROLS

Tailgate

Depending on optional features and country version, this setting is not offered in some cases.

1. "Settings"

2. "Doors/key"

3. Select the symbol.

4. Select the desired function.

▷ "Tailgate"

Only the tailgate is unlocked.

▷ "Tailgate + door(s)"

The tailgate and the doors are un‐ locked.

Locking

The settings are saved in the active profile. Per‐ sonal Profile, refer to page 35.

"Settings"

2. "Doors/key"

3. Select desired setting.

▷ "Lock if no door is opened"

The vehicle locks automatically after a short period of time if no door is opened.

▷ "Lock after start driving"

The vehicle locks automatically after you drive off.

Confirmation signals from the vehicle

"Settings"

2. "Doors/key"

3. Select desired setting.

▷ "Acoustic sig. lock/unlock"

Unlocking is signaled by one honk of the horn.

▷ "Flash when lock/unlock"

Unlocking is signaled by two flashes, locking by one.

Alarm system

The concept

When the vehicle is locked, the vehicle alarm system responds to:

▷ Opening a door, the hood or the tailgate.

▷ Movements in the vehicle interior

▷ Changes in the vehicle tilt, e. g., during at‐

tempts at stealing a wheel or when towing the car.

▷ Disconnected battery voltage.

The alarm system briefly signals tampering:

▷ Acoustic alarm.

▷ By switching on the hazard warning system.

▷ By flashing the daytime running lights.

Arming and disarming the alarm system

When you lock or unlock the vehicle, either with the remote control or via the Comfort Ac‐ cess, the alarm system is armed or disarmed at the same time.

Door lock and armed alarm system

The alarm system is triggered when the door is opened, when the vehicle is unlocked via the door lock.

Switch off the alarm, refer to page 44.

Tailgate and armed alarm system

The tailgate can be opened even when the alarm system is armed.

After the tailgate is closed, it is locked and monitored again when the doors are locked. The hazard warning system flashes once.

Panic mode

You can trigger the alarm system if you find yourself in a dangerous situation.

Press button on the remote control for at least 3 seconds.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 48

CONTROLS

Opening and closing

To reel off the alarm: press any button.

Indicator lamp on the interior rearview mirror

▷ The indicator lamp flashes briefly every

2 seconds:

The system is armed.

▷ The indicator lamp flashes after locking:

The doors, hood or tailgate is not closed properly, but the rest of the vehicle is se‐ cured.

After 10 seconds, the indicator lamp flashes continuously. Interior motion sensor and tilt alarm sensor are not active.

When the still open access is closed, interior motion sensor and tilt alarm sensor will be switched on.

▷ The indicator lamp goes out after unlock‐

ing:

The vehicle has not been tampered with.

▷ The indicator lamp flashes after unlocking

until the engine ignition is switched on, but no longer than approx. 5 minutes:

An alarm has been triggered.

Tilt alarm sensor

The tilt of the vehicle is monitored.

The alarm system responds in situations such as attempts to steal a wheel or when the car is towed.

Interior motion sensor

The windows and glass sunroof must be closed for the system to function properly.

Avoiding unintentional alarms

The tilt alarm sensor and interior motion sensor can be switched off together, such as in the fol‐ lowing situations:

▷ In automatic car washes.

▷ In duplex garages.

▷ During transport on trains carrying vehicles,

at sea or on a trailer.

▷ With animals in the vehicle.

Switching off the tilt alarm sensor and interior motion sensor

Press the remote control button again within 10 seconds as soon as the vehi‐

cle is locked.

The indicator lamp lights up for approx. 2 sec‐ onds and then continues to flash.

The tilt alarm sensor and interior motion sensor are turned off, until the vehicle is locked again.

Switching off the alarm

▷ Unlock vehicle with the remote control or

switch on the ignition, if needed through emergency detection of remote control, re‐ fer to page 35.

▷ With Comfort Access: If you are carrying the

remote control on your person, grasp the driver side or front passenger side door handle completely.

Unlock vehicle with the remote control or switch on the ignition, if needed through emer‐ gency detection of remote control, refer to page 35.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 49

Opening and closing

CONTROLS

Power windows

Note

Take the remote control with you

Take the remote control with you when leaving the vehicle so that children, e.g., cannot operate the power windows and injure them‐ selves.◀

On 5-door models

On 3-door models

Closing

Keep the closing path clear

Monitor closing and make sure that the closing path of the window is clear; otherwise, injuries may result.◀

Pull switch up.

The window closes while the reel is held.

See also: closing by means of Comfort Access, refer to page 41.

Pinch protection system

Danger of jamming even with pinch pro‐

tection

Even with the pinch protection system, check that the window's closing path is clear; other‐ wise, the closing action may not stop in certain situations, e.g., if thin objects are present.◀

No window accessories

Do not install any accessories in the win‐ dow's range of movement; otherwise, the pinch protection system will be impaired.◀

If closing force exceeds a specific margin as a window closes, closing is interrupted.

The window reopens slightly.

Opening

▷

See also: Convenient opening, refer to page 38, via remote control.

Press the button to the resistance

point.

The window opens while the switch is held.

Press the switch beyond the resist‐

ance point.

The window opens automatically. Pressing again stops the motion.

Online Edition for Part no. 01 40 2 961 168 - II/15

Closing without the pinch protection system

Keep the closing path clear

Monitor closing and make sure that the closing path of the window is clear; otherwise, injuries may result.◀

E. g. danger from the outside or ice might pre‐ vent window from closing properly - proceed as follows:

Pull the switch past the resistance point and

hold it there.

The pinch protection is limited and the win‐ dow reopens slightly if the closing force ex‐ ceeds a certain margin.

Page 50

CONTROLS

Opening and closing

2. Pull the switch past the resistance point

again within approx. 4 seconds and hold it there.

The window closes without jam protection.

On 5-door models: safety switch

The safety switch in the driver's door can be used to prevent children, e.g., from opening and closing the rear windows using the switches in the rear.

Switching on and off

Press button.

The LED lights up if the safety function

is switched on.

Safety switch for rear operation

Press the safety switch when transporting children in the rear; otherwise, injury may result if the windows are closed without supervi‐ sion.◀

Panoramic glass sun‐ roof

Hints

Keep the closing path clear

Monitor closing and make sure that the closing path of the glass sunroof is clear; other‐ wise, injuries may result.◀

Take the remote control with you

Take the remote control with you when leaving the vehicle so that children, e.g., cannot operate the glass sunroof and injure them‐ selves.◀

At a glance

Tilting the glass sunroof

Press back the reel up to or be‐ yond the resistance point and re‐ lease it.

The glass sunroof is raised.

Opening glass sunroof

When the glass sunroof is closed

Press the reel back beyond the resistance point and release it twice.

The glass sunroof is opened.

Pressing the reel again stops the

motion.

With the glass sunroof completely raised

▷ Slide reel back to the resist‐

ance point and hold.

The glass sunroof is opened as long as the reel is pressed.

▷ Press the reel back beyond

the resistance point and re‐ lease it.

The glass sunroof is opened.

Pressing the reel again stops the motion.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 51

Opening and closing

CONTROLS

Comfort position

If the glass sunroof stops before it is completely opened, it is in the Comfort position. In this po‐ sition the wind noises in the interior are the least.

If desired, continue the movement by pressing the reel.

Closing glass sunroof

With the glass sunroof open

▷ Slide reel forward to the re‐

sistance point and hold.

The glass sunroof is closed as long as the reel is pressed and stops in the raised posi‐ tion.

▷ Press the reel forward beyond the resist‐

ance point and release it.

The glass sunroof is closed and stops in the raised position.

Pressing the reel toward the back stops the motion.

▷ Press the reel forward beyond the resist‐

ance point and release it twice.

The glass sunroof is closed.

Pressing the reel again stops the motion.

Danger of jamming even with pinch pro‐ tection

Despite the pinch protection system, check that the glass sunroof's closing path is clear; other‐ wise, the closing action may not be interrupted in certain extreme situations, such as when thin objects are present.◀

Closing without the pinch protection system

E. g. if there is an external danger, proceed as follows:

Press the reel forward beyond the resist‐

ance point and hold it.

The pinch protection is limited and the glass sunroof reopens slightly if the closing force exceeds a certain margin.

2. Press the reel forward again beyond the re‐

sistance point and hold until the glass sun‐ roof closes without jam protection. Make sure that the closing area is clear.

Initializing after a power failure

After a power failure, it can happen that the glass sunroof can only be raised. The system must be initialized in this case. MINI recom‐ mends having this work performed by your service center.

With the glass sunroof completely raised

Press the reel forward beyond the resistance point and release it.

The glass sunroof is closed.

Pinch protection system

If the closing force exceeds a specific value as a glass sunroof closes, the closing action is inter‐ rupted.

The glass sunroof reopens slightly.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 52

CONTROLS

Adjusting

Vehicle features and op‐ tions

Sitting safely

The ideal seating position can make a vital con‐ tribution to relaxed, fatigue-free driving.

The seating position plays an important role in an accident in combination with:

▷ Safety belts, refer to page 50.

▷ Head restraints, refer to page 51.

▷ Airbags, refer to page 95.

Seats

would eliminate the protection normally pro‐ vided by the belt.◀

Keep the movement area unobstructed

When changing the seat position, keep the seat's area of movement unobstructed; otherwise, people might get injured or objects damaged.◀

Adjusting seats

Overview

1 Forward/backward

2 Thigh support

3 Height

4 Backrest tilt

Hints

Do not adjust the seat while driving

Do not adjust the driver's seat while driv‐ ing, or the seat could respond with unexpected movement and the ensuing loss of vehicle con‐ trol could lead to an accident.◀

Do not incline the backrest too far to the

rear

Do not incline the backrest too far to the rear while driving, or there is a risk of slipping under the safety belt in the event of an accident. This

Online Edition for Part no. 01 40 2 961 168 - II/15

Forward/backward

Pull the lever and slide the seat in the desired direction.

Page 53

After releasing the lever, move the seat forward or back slightly making sure it engages prop‐ erly.

Height

Pull the lever up or press it down as often as needed to reach the desired height.

Backrest tilt

Adjusting

Turn the wheel in order to increase or decrease the curvature.

CONTROLS

Thigh support

Pull the lever and apply your weight to the backrest or lift it off, as necessary.

Lumbar support

The curvature of the seat backrest can be ad‐ justed in a way that it supports the lumbar re‐ gion of the spine. The lower back and the spine are supported for upright posture.

Online Edition for Part no. 01 40 2 961 168 - II/15

Pull the lever at the front of the seat and adjust the thigh support.

In 3-door models: entering the rear

Hints

Folding back and locking the backrest

Before driving off, fold back and lock the backrests; otherwise, an unexpected seat movement may cause an accident.◀

Keep the movement area unobstructed

When changing the seat position, keep the seat's area of movement unobstructed; otherwise, people might get injured or objects damaged.◀

Page 54

CONTROLS

Adjusting

Fold down seat back

1. Pull lever up to the stop.

2. Fold backrest forward.

3. Push the seat forward.

Original position

The driver's seat features a mechanical mem‐ ory function for forward/back and backrest ad‐ justment.

Push the seat back into the original posi‐

tion.

2. Fold back the backrest to lock the seat.

If the backrest is folded back when the seat is not yet in the original position, the seat latches in the current position. In this case, manually adjust longitudinal direction, refer to page 48.

Front seat heating

Switching on

Press button once for each tempera‐ ture level.

The maximum temperature is reached when three LEDs are lit.

If the journey is continued within approx. 15 minutes, the seat heating is activated automat‐ ically with the temperature selected last.

When Green mode, refer to page 162, is acti‐ vated, the heater output is reduced.

Switch off

Press button longer.

The LEDs go out.

Safety belts

Seats with safety belt

The vehicle has four or five seating positions, each of which is equipped with a safety belt.

Number of safety belts

Your vehicle has been fitted with four or five safety belts for your and your passengers' safety. However, they can only offer protection when adjusted correctly.

General information

Always make sure that safety belts are being worn by all occupants before driving off.

For the occupants' safety the belt locking mechanism triggers early. Slowly guide the belt out of the holder when applying it.

If needed, disengage the belt in the rear from the belt buckle on the side.

Although airbags enhance safety by providing added protection, they are not a substitute for safety belts.

The two outer safety belt buckles, integrated into the rear seat, are for passengers sitting on the left and right.

The center rear safety belt buckle is solely in‐ tended for the center passenger.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 55

Adjusting

CONTROLS

Hints

One person per safety belt

Never allow more than one person to wear a single safety belt. Never allow infants or small children to ride on a passenger's lap.◀

Putting on the belt

Lay the belt, without twisting, snugly across the lap and shoulders, as close to the body as possible. Make sure that the belt lies low around the hips in the lap area and does not press on the abdomen. Otherwise, the belt can slip over the hips in a frontal impact and in‐ jure the abdomen.

The safety belt must not lie across the neck, rub on sharp edges, be routed over breakable ob‐ jects, or be pinched.◀

What reduces the restraining effect

Avoid wearing bulky clothing, and pull the shoulder belt periodically to readjust the tension. Make sure that the belt is not jammed; otherwise, the belt can be damaged and the restraining effect is reduced.◀

Using the middle safety belt

If the middle safety belt in the rear is used, the larger side of the backrest must be locked. Otherwise, the safety belt will not have a restraining effect.◀

Buckling the belt

Make sure you hear the latch plate engage in the belt buckle.

Unbuckling the belt

1. Hold the belt firmly.

2. Press the red button in the belt buckle.

3. Guide the belt back into its roll-up mecha‐

nism.

Safety belt reminder for driver's seat and front passenger seat

The indicator lamp lights up and a sig‐ nal sounds. Make sure that the safety

belts are positioned correctly. The safety belt reminder is active at speeds above approx. 6 mph/10 km/h. It can also be acti‐ vated if objects are placed on the front passen‐ ger seat.

Damage to safety belts

Wear and tear after accidents or when dam‐ aged otherwise:

Have the safety belts, including the safety belt tensioners, replaced and have the belt anchors checked.

Check and replace safety belts

This should only be done by your service center; otherwise, this safety feature might not work properly.◀

Front head restraints

Correctly adjusted head restraint

A correctly adjusted head restraint reduces the risk of injury to cervical vertebrae in the event of an accident.

Adjust the headrest via the backrest tilt as needed.

Adjusting the head restraint

Adjust the head restraints of all occupied seats properly; otherwise, there is an increased risk of injury in an accident.◀

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 56

CONTROLS

Adjusting

Height

Adjust the head restraint so that its center is approximately at ear level.

Distance

Adjust the distance so that the head restraint is as close as possible to the back of the head.

If necessary, adjust the distance by adjusting the tilt of the backrest.

Adjusting the height

▷ To raise: pull.

▷ To lower: press button, arrow 1, and push

headrest down.

Before transporting passengers

Reinstall the head restraint before trans‐ porting anyone in the seat; otherwise, the pro‐ tective function of the head restraint is unavail‐ able.◀

Rear head restraints

Correctly adjusted head restraint

A correctly adjusted head restraint reduces the risk of injury to cervical vertebrae in the event of an accident.

Adjusting the head restraint

Adjust the head restraints of all occupied seats properly; otherwise, there is an increased risk of injury in an accident.◀

Height

Adjust the head restraint so that its center is approximately at ear level.

Adjusting the height

Removing

Only remove the head restraint if no one will be sitting in the seat in question.

Pull head restraint up as far as possible.

2. Press button, arrow 1, and pull the head re‐

straint out completely.

To remove the headrest, fold the backrest rear‐ ward if it is in the upright position.

Online Edition for Part no. 01 40 2 961 168 - II/15

▷ To raise: push.

▷ To lower: press button, arrow 1, and push

headrest down.

Folding down head restraints

Extending/retracting head restraint

Only fold down head restraint if no pas‐ sengers are in the rear. Fold out retracted headrests again if passengers are being carried

Page 57

Adjusting

CONTROLS

in the rear; otherwise, there is increased risk of injury in the event of an accident.◀

▷ To lower flaps: press the button, arrow 1,

and press down the head restraint.

▷ Fold back up: pull up head restraints.

Removing

Only remove the head restraint if no one will be sitting in the seat in question.

Fold the seat down, refer to page 145, before removing the head restraint, otherwise the head restraint cannot be removed.

Mirrors

Exterior mirrors

General information

The mirror on the passenger side is more curved than the driver's side mirror.

Depending on the vehicle equipment, the mir‐ ror setting is stored for the profile currently in use. When the vehicle is unlocked via the re‐ mote control, the position is automatically re‐ trieved if this function is active.

Note

Estimating distances correctly

Objects reflected in the mirror are closer than they appear. Do not estimate the distance to the traffic behind you based on what you see in the mirror, as this will increase your risk of an accident.◀

Overview

Pull head restraint up against the resist‐

ance.

2. Press button, arrow 1, and pull the head re‐

straint out completely.

Before transporting passengers

Reinstall the head restraint before trans‐ porting anyone in the seat; otherwise, the pro‐ tective function of the head restraint is unavail‐ able.◀

Online Edition for Part no. 01 40 2 961 168 - II/15

1 Adjusting 54

2 Left/right, Automatic Curb Monitor

3 Fold in and out 54

Selecting a mirror

To change over to the other mirror:

Slide the switch.

Page 58

CONTROLS

Adjusting

Adjusting electrically

The setting corresponds to the direction in which the button is pressed.

Adjusting manually

In case of electrical malfunction press edges of mirror.

Automatic Curb Monitor

The concept

If reverse gear is engaged, the mirror glass on the front passenger side is tilted downward. This improves your view of the curb and other low-lying obstacles when parking, e.g.

Activating

1. Slide the switch to the driver's side

mirror position.

2. Engage selector lever position R.

Deactivating

Slide the switch to the passenger side mirror position.

Fold in the mirror in a car wash

Before washing the car in an automatic car wash, fold in the exterior mirrors by hand or with the button; otherwise, the mirrors could be damaged, depending on the width of the vehicle.◀

Automatic heating

Both exterior mirrors are automatically heated whenever the engine is running.

Automatic dimming feature

Both exterior mirrors are automatically dim‐ med. Photocells are used to control the Interior rearview mirror, refer to page 55.

Interior rearview mirror, manually dimmable

Flip lever

Fold in and out

Press button.

Possible at speeds up to approx. 15 mph/20 km/h.

E. g. this is advantageous

▷ In car washes.

▷ In narrow streets.

▷ For folding mirrors back out that were

folded away manually.

Mirrors that were folded in are folded out auto‐ matically at a speed of approx. 25 mph/40 km/h.

Online Edition for Part no. 01 40 2 961 168 - II/15

To reduce the blinding effect of the interior rear view mirror, flip the lever forward.

Page 59

Adjusting

CONTROLS

Turn knob

Turn the knob to reduce the blinding effect by the interior mirror.

Interior rearview mirror, automatic dimming feature

The concept

Photocells are used for control:

▷ In the mirror glass.

▷ On the back of the mirror.

Steering wheel

Note

Do not adjust while driving

Do not adjust the steering wheel while driving; otherwise, an unexpected movement could result in an accident.◀

Adjusting

1. Switch on the ignition.

2. Fold the lever down.

3. Move the steering wheel to the preferred

height and angle to suit your seating posi‐ tion.

4. Fold the lever back.

5. Switch off the ignition again if needed.

Functional requirement

For proper operation:

▷ Keep the photocells clean.

▷ Do not cover the area between the inside

rearview mirror and the windshield.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 60

CONTROLS

Transporting children safely

Vehicle features and op‐ tions

This chapter describes all standard, countryspecific and optional features offered with the series. It also describes features that are not

The right place for children

Note

Children in the vehicle

Do not leave children unattended in the vehicle; otherwise, they could endanger them‐ selves and other persons, e.g., by opening the doors.◀

Children should always be in the rear

Accident research shows that the safest place for children is in the back seat.

Transporting children in the rear

Only transport children younger than 13 years of age or shorter than 5 ft/150 cm in the rear in child restraint systems provided in accordance with the age, weight and size of the child; otherwise, there is an increased risk of injury in an accident.

Children 13 years of age or older must wear a safety belt as soon as a suitable child restraint system can no longer be used due to their age, weight and size.◀

Children on the front passenger seat

Should it ever be necessary to use a child re‐ straint system in the front passenger seat, make sure that the front, knee and side airbags on the front passenger side are deactivated. Automatic deactivation of front-seat passenger airbags, refer to page 97.

Note

Deactivating the front-seat passenger air‐ bags

If a child restraint system is used in the front passenger seat, deactivate the front-seat pas‐ senger airbags; otherwise, there is an increased risk of injury to the child when the airbags are activated, even with a child restraint system.◀

Installing child re‐ straint systems

Hints

Manufacturer's information for child re‐ straint systems

To select, mount and use child restraint sys‐ tems, observe the information provided by the system manufacturer; otherwise, the protective effect can be lost.◀

Ensuring the stability of the child seat

When installing child restraint systems, make sure that the child seat is securely fas‐ tened to the backrest of the seat. Angle and headrest of the backrest might need to be ad‐ justed or possibly be removed. Make sure that all backrests are securely locked. Otherwise the stability of the child seat can be affected, and

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 61

Transporting children safely

CONTROLS

there is an increased risk of injury because of unexpected movement of the seat backrest.◀

In order to faciliate the installation of a backfacing child restraint system in the rear:

move the front passenger's seat as far up as possible before folding down the backrest.

On the front passenger seat

Deactivating airbags

After installing a child restraint system in the front passenger seat, make sure that the front, knee and side airbags on the front passenger side are deactivated.

Deactivate the front-seat passenger airbags au‐ tomatically, refer to page 97.

Deactivating the front-seat passenger air‐ bags

Seat position and height

Before installing a child restraint system, move the front passenger seat as far back as possible and adjust its height to the highest and thus best possible position for the belt and to offer optimal protection in the event of an accident.

If the upper anchorage of the safety belt is lo‐ cated in front of the belt guide of the child seat,

move the passenger seat carefully forward until the best possible belt guide position is reached.

Child seat security

The rear safety belts and the front passenger safety belt can be permanently locked to fasten child restraint systems.

Locking the safety belt

Pull out the strap completely.

2. Secure the child restraint system with the

belt.

3. Allow the strap to be pulled in and pull it

tight against the child restraint system. The safety belt is locked.

Unlocking the safety belt

Unbuckle the belt buckle.

2. Remove the child restraint system.

3. Allow the strap to be pulled in completely.

LATCH child restraint system

LATCH: Lower Anchors and Tether for Children.

Note

Follow manufacturer's information for LATCH child restraint systems

To mount and use the LATCH child restraint sys‐ tems, observe the operating and safety infor‐

Online Edition for Part no. 01 40 2 961 168 - II/15

mation from the system manufacturer; other‐ wise, the level of protection may be reduced.◀

Mounts for the lower LATCH anchors

The lower anchors may be used to attach the CRS to the vehicle seat up to a combined child

Page 62

CONTROLS

Transporting children safely

and CRS weight of 65 lb when the child is re‐ strained by the internal harnesses.

Properly engage the lower LATCH an‐ chors

Make sure that the lower LATCH anchors have properly engaged and that the child restraint system is resting snugly against the backrest; otherwise, the degree of protection may be re‐ duced.◀

Before mounting the LATCH child restraint sys‐ tem, pull the belt away from the child restraint system.

Position

The corresponding symbol shows the mounts for the lower LATCH anchors. Seats equipped with lower anchors are marked with a pair, 2, of LATCH sym‐

bols. It is not recommended to use the inner lower anchors of standard outer LATCH positions to fasten a child restraint system on the middle seat. Use the vehicle seat belt in‐ stead for the middle seat.

Assembly of LATCH child restraint systems

Mount the child restraint system; refer to

the user's manual of the system.

2. Ensure that both LATCH anchors are prop‐

erly connected.

Child restraint fixing system with a tether strap

Note

Mounting eyelets

Use the mounting eyes only for the upper retaining strap to secure child restraint systems; otherwise, the mounting eyes could be dam‐ aged.◀

Mounting points

The respective symbol shows the an‐ chor for the upper retaining strap. Seats

with an upper Top Tether are marked with this symbol. It can be found on the rear seat backrest or the rear window shelf.

Retaining strap guide

Retaining strap

Make sure that the upper retaining strap is not passed over the head restraints or sharp edges and is not twisted up to the upper mounting points; otherwise, the belt cannot properly secure the child restraint system in an accident.◀

1 Direction of travel

2 Head restraint

3 Hook for upper retaining strap

4 Mounting point/eye

5 Seat backrest

6 Upper retaining strap

Attaching the upper retaining strap to the mounting point

Raise the head restraint if needed.

2. Guide the upper retaining strap between

the supports of the head restraint.

3. Attach the hook of the retaining strap to

the mounting eye on the rear seat.

4. Tighten the retaining strap by pulling it

down.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 63

Transporting children safely

CONTROLS

No persons on the back seat when there is a child restraint system with an upper

retaining strap on the front passenger seat.

When there is a child restraint system with an upper retaining strap on the front passenger seat, no one should sit in the back seat directly behind it, otherwise there is an increased risk of injury due to the upper retaining strap.◀

Upper retaining strap when the backrest is folded down

When the backrest is folded down, do not guide the belt through the head restraint sup‐ ports on the backrest; otherwise the belt may not secure the child restraint system properly in case of an accident◀

ON 5-door models: Lock‐ ing the doors and win‐ dows

Rear doors

This locks various functions so that they cannot be operated from the rear: safety switch, refer to page 46.

Push the locking lever on the rear doors up.

The door can now be opened from the outside only.

Safety switch for the rear

Press button on the driver's door if children are being transported in the

rear.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 64

CONTROLS

Driving

Vehicle features and op‐ tions

Start/Stop button

The concept

Pressing the Start/Stop button switches the ignition on or off and starts the engine.

Steptronic transmission: the en‐

gine starts in selector lever posi‐ tion P or N with the brake pedal pressed when you press the Start/Stop button.

Manual transmission: the engine starts with the clutch pedal pressed when the Start/Stop but‐ ton is pressed.

Ignition on

Steptronic transmission: press the Start/Stop button, and do not press on the brake pedal at the same time.

Manual transmission: press the Start/Stop but‐ ton without stepping on the clutch pedal.

All vehicle systems are ready for operation.

Most of the indicator and warning lights in the instrument cluster light up for a varied length of time.

To save battery power when the engine is off, switch off the ignition and any unnecessary electronic systems/power consumers.

Ignition off

Manual transmission: press the Start/Stop but‐ ton again without stepping on the clutch pedal.

Steptronic transmission: shift to selector lever position P, press the Start/Stop button again without stepping on the brake.

All indicator lights in the instrument cluster go out.

To save battery power when the engine is off, switch off the ignition and any unnecessary electronic systems/power consumers.

Ignition automatically cuts off while the vehicle is stationary and the engine is stopped:

▷ During locking, also with the low beams ac‐

tivated.

▷ Shortly before the battery is discharged

completely, so that the engine can still be started. This function is only available when the low beams are turned off.

▷ When opening and closing the driver door,

if the driver's safety belt is unbuckled and the low beams are turned off.

▷ While the driver's safety belt is unbuckled

with driver's door open and low beams off.

▷ The low beams switch to parking lights af‐

ter approx. 15 minutes of no use.

Radio ready state

Activate radio-ready state:

▷ When the engine is running: press the Start/

Stop button.

Some electronic systems/power consumers re‐ main ready for operation.

Radio ready state switches off automatically:

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 65

Driving

CONTROLS

▷ After approx. 8 minutes.

▷ When the vehicle is locked using the central

locking system.

▷ Shortly before the battery is discharged

completely, so that the engine can still be started.

The radio-ready state remains active if, e.g., the ignition is automatically switched off for the fol‐ lowing reasons:

▷ Opening or closing the driver's door.

▷ Unfastening of the driver's safety belt.

▷ When automatically switching from low

beams to parking lights.

If the engine is switched off and the ignition is switched on, the system automatically switches to the radio-ready state if the lights are turned off or, if correspondingly equipped, the day‐ time running lights are activated.

Starting the engine

Hints

Enclosed areas

Do not let the engine run in enclosed areas, since breathing in exhaust fumes may lead to loss of consciousness and death. The exhaust gases contain carbon monoxide, an odorless and colorless but highly toxic gas.◀

posing a risk of overheating and damage to the catalytic converter.◀

Do not wait for the engine to warm-up while the vehicle remains stationary. Start driving at moderate engine speeds.

Steptronic transmission

Starting the engine

1. Depress the brake pedal.

2. Engage selector lever position P or N.

3. Press the Start/Stop button.

The ignition is activated automatically for a cer‐ tain time and is stopped as soon as the engine starts.

Manual transmission

Starting the engine

Depress the brake pedal.

2. Press on the clutch pedal and shift to neu‐

tral.

3. Press the Start/Stop button.

The ignition is activated automatically for a cer‐ tain time and is stopped as soon as the engine starts.

Engine stop

Unattended vehicle

Do not leave the vehicle unattended with the engine running; doing so poses a risk of danger.

Before leaving the vehicle with the engine run‐ ning, set the parking brake and place the trans‐ mission in selector lever position P or N to pre‐ vent the vehicle from moving.◀

Repeated starting in quick succession

Avoid trying to start the vehicle repeat‐ edly and in quick succession. Otherwise, the fuel is not burned or is inadequately burned,

Online Edition for Part no. 01 40 2 961 168 - II/15

Hints

Take the remote control with you

Take the remote control with you when leaving the vehicle so that children, e.g., cannot start the engine.◀

Apply parking brake and further secure

the vehicle if needed.

Set the parking brake firmly when parking; oth‐ erwise, the vehicle could roll. On steep upward and downward inclines, further secure the ve‐

Page 66

CONTROLS

Driving

hicle, e.g., by turning the steering wheel in the direction of the curb.◀

Before driving into a car wash

So that the vehicle can roll into a car wash ob‐ serve instructions for going into an automatic car wash, refer to page 214.

Steptronic transmission

Switching off the engine

1. Engage selector lever position P with the

vehicle stopped.

2. Press the Start/Stop button.

The engine is switched off.

The radio-ready state is switched on.

3. Set the parking brake.

Manual transmission

Switching off the engine

With the vehicle at a standstill, press the

Start/Stop button.

The engine is switched off.

The radio-ready state is switched on.

2. Shift into first gear or reverse.

3. Set the parking brake.

the Auto Start/Stop function is active, it is avail‐ able when the vehicle is traveling faster than about 3 mph, approx. 5 km/h.

Engine stop

The engine is switched off automatically during a stop under the following conditions:

Manual transmission:

▷ Neutral is engaged and the clutch pedal is

not pressed.

▷ The driver's safety belt is buckled or the

driver's door is closed.

Steptronic transmission:

▷ The selector lever is in selector lever posi‐

tion D.

▷ Brake pedal remains depressed while the

vehicle is stopped.

▷ The driver's safety belt is buckled or the

driver's door is closed.

In order to be able to release the brake pedal, engage lever in position P. The engine remains off.

To continue driving depress the brake pedal. When a gear is engaged, the engine starts au‐ tomatically.

The air flow from the air conditioner is reduced when the engine is switched off.

Auto Start/Stop function

The concept

The Auto Start/Stop function helps save fuel. The system switches off the engine during a stop, e.g., in traffic congestion or at traffic lights. The ignition remains switched on. The engine starts again automatically for driving off.

Automatic operation

After every start of the engine using the Start/ Stop button, the Auto Start/Stop function is in the last selected state, refer to page 63. When

Online Edition for Part no. 01 40 2 961 168 - II/15

Displays in the instrument cluster

The display indicates that the Auto Start/Stop function is ready for an Automatic engine start.

The display indicates that the conditions for an automatic en‐ gine stop have not been met.

Page 67

Driving

CONTROLS

Functional limitations

The engine is not switched off automatically in the following situations:

▷ External temperature too low.

▷ The external temperature is high and auto‐

matic climate control is running.

▷ The car's interior has not yet been heated

or cooled to the required level.

▷ The engine is not yet at operating tempera‐

ture.

▷ The wheels are at a sharp angle or the

steering wheel is being turned.

▷ After driving in reverse.

▷ Fogging of the windows when the auto‐

matic climate control is switched on.

▷ The vehicle battery charge is very low.

▷ At higher elevations.

▷ The engine compartment lid is unlocked.

▷ The parking assistant is activated.

▷ Stop-and-go traffic.

▷ Selector lever in selector lever position R, N

or M/S.

Starting the engine

The engine starts automatically under the fol‐ lowing conditions:

▷ Manual transmission:

The clutch pedal is pressed.

▷ Steptronic transmission:

By releasing the brake pedal.

After the engine starts, accelerate as usual.

Some indicator lights light up for a varied length of time.

The engine can only be started via the Start/ Stop button.

Functional limitations

Even if driving off was not intended, the deacti‐ vated engine starts up automatically in the fol‐ lowing situations:

▷ Excessive warming of the car's interior

when the cooling function is switched on.

▷ The steering wheel is turned.

▷ Steptronic transmission: change from selec‐

tor lever position D to R, N or M/S.

▷ Steptronic transmission: change from selec‐

tor lever position P to R, N, D or M/S.

▷ The vehicle begins rolling.

▷ Fogging of the windows when the auto‐

matic climate control is switched on.

▷ The vehicle battery charge is very low.

▷ Excessive cooling of the car's interior when

the heating is switched on.

▷ Manual transmission: low brake vacuum

pressure; this can occur, e.g., if the brake pedal is depressed a number of times in succession.

Switching the system on/off

Using the button

Safety mode

After the engine switches off automatically, it will not start again automatically if any one of the following conditions are met.

▷ The driver's safety belt is unbuckled and

the driver's door is open.

▷ The hood was unlocked.

Online Edition for Part no. 01 40 2 961 168 - II/15

Press button.

Page 68

CONTROLS

Driving

▷ LED comes on: Auto Start/Stop function is

deactivated.

The engine is started during an automatic engine stop.

The engine can only be stopped or started via the Start/Stop button.

▷ LED goes out: Auto Start/Stop function is

activated.

Switching off the vehicle during an automatic engine stop

During an automatic engine stop, the vehicle can be switched off permanently, e. g., when leaving it.

Steptronic transmission: engage selector

lever position P.

2. Press the Start/Stop button. The ignition is

switched off. The Auto Start/Stop function is deactivated.

3. Manual transmission: shift into first gear or

reverse.

4. Set the parking brake.

Engine start as usual via Start/Stop button.

Automatic deactivation

In certain situations, Auto Start/Stop function is deactivated automatically for safety reasons as if the driver were absent.

Malfunction

The Auto Start/Stop function no longer switches off the engine automatically. A Check Control message is displayed. It is possible to continue driving. Have the system checked.

The indicator lamp lights up red. The parking brake is set.

Lower lamp: indicator lamp in Canadian models

Releasing

Raise lever slightly, press the button and guide the lever down.

Hints

Use while driving

On rare occasions if it is necessary to use the parking brake while driving, do not use ex‐ cessive force when applying it. When using it, keep the button on the lever depressed.

Otherwise, using excessive force when applying the parking brake may cause the rear wheels to lock, resulting in fishtailing.◀

To prevent corrosion and one-sided brake ac‐ tion, lightly apply the parking brake periodically while coasting, if traffic conditions permit.

The brake lights will not light up if the parking brake is set.

Parking brake

Applying

The lever automatically engages after being pulled up.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 69

Driving

CONTROLS

Turn signal, high beams, headlight flasher

Turn signal

Using turn signals

Press the lever beyond the resistance point.

To switch off manually, press the lever to the resistance point.

Unusually rapid flashing of the indicator lamp indicates that a turn signal bulb has failed.

Triple turn signal activation

Press the lever to the resistance point.

The turn signal flashes three times.

The function can be activated or deactivated.

On the Control Display:

"Settings"

2. "Lighting"

3. "Triple turn signal"

Settings are stored for the profile currently in use.

Signaling briefly

Press the lever to the resistance point and hold it there for as long as you want the turn signal to flash.

High beams, headlight flasher

▷ High beams, arrow 1.

▷ Headlight flasher, arrow 2.

Washer/wiper system

Switching the wipers on/off and brief wipe

Hints

Do not activate wipers if frozen to wind‐ shield

Do not switch on the wipers if they are frozen to the windshield; otherwise, the wiper blades and the wiper motor may be damaged.◀

Do not activate wipers on dry windshield

Do not use the wipers if the windshield is dry, as this may damage the wiper blades or cause them to become worn more quickly.◀

Do not activate wipers with wipers folded

away

Do not switch on the wipers if they are folded away, otherwise the hood or the wipers may be damaged.◀

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 70

CONTROLS

Driving

Switching on

Push wiper lever up.

The lever automatically returns to its initial po‐ sition when released.

▷ Normal wiper speed: push up once.

The wipers switch to intermittent operation when the vehicle is stationary.

▷ Fast wiper speed: press up twice or press

once beyond the resistance point.

Wipers change to normal speed when vehi‐ cle comes to standstill.

Switch off and brief wipe

Interval mode or rain sensor

The concept

Without the rain sensor, the frequency of the wiper operation is preset.

The rain sensor automatically controls the time between wipes depending on the intensity of the rainfall. The sensor is located on the wind‐ shield, directly behind the interior rearview mir‐ ror.

Activating/deactivating

Press button on the wiper lever.

The LED in the wiper lever lights up and wiping starts. When wipers are frozen to windshield, wiper operation is deactivated.

Push wiper lever down.

The lever automatically returns to its initial po‐ sition when released.

▷ Single wipe: press down once.

▷ To switch off normal wipe: press down

once.

▷ To switch off fast wipe: press down twice.

Online Edition for Part no. 01 40 2 961 168 - II/15

Deactivate the rain sensor in car washes

Deactivate the rain sensor when passing through an automatic car wash; otherwise, un‐ intentional wiping can cause damages.◀

Setting the frequency or sensitivity of the rain sensor

Turn the thumbwheel.

Page 71

Driving

CONTROLS

Washing the windshield

Pull the wiper lever towards you.

The system sprays washer fluid on the wind‐ shield and activates the wipers briefly.

Do not use the washer system at freezing temperatures

Do not use the washers if fluid could freeze onto the windshield which might impede your viewing field. Therefore use antifreeze fluid.

Avoid using the washer when the reservoir is empty; operation might damage pump.◀

Windshield washer nozzles

The windshield washer nozzles are automati‐ cally heated while the ignition is switched on.

Rear window wiper

Switching on the rear window wiper

Cleaning rear window

In interval mode: turn the switch further, ar‐ row 2. The switch automatically returns to its interval position when released.

In idle position: turn switch downward, arrow 3. The switch automatically returns to its idle posi‐ tion when released.

Fold-out position of the wipers

Helpful when changing the wiper blades or un‐ der frosty conditions, e.g.

1. Switch the ignition on and off again.

2. With icy conditions make sure that blades

are not frozen to the windshield.

3. Press the wiper lever up beyond the point

of resistance and hold it for approx. 3 sec‐ onds, until the wiper remains in a nearly vertical position.

After the wipers are folded back down, the wiper system must be reactivated.

Folding wipers back down

Before switching the ignition on, fold the wipers back down to the windshield; otherwise, the wipers may become damaged when they are activated.◀

Switch on the ignition.

2. Push wiper lever down. Wipers move to

their resting position and are ready again for operation.

Turn the switch from idle position 0 upward, ar‐ row 1: interval mode. When reverse gear is en‐ gaged, the system switches to continuous op‐ eration.

Online Edition for Part no. 01 40 2 961 168 - II/15

Washer fluid

Hints

Antifreeze for washer fluid

Antifreeze is flammable and can cause in‐ jury if it is used incorrectly.

Therefore, keep it away from possible sources of ignition.

Only keep it in the closed original container and inaccessible to children.

Page 72

CONTROLS

Driving

Follow the notes and instructions on the con‐ tainer.

United States: The washer fluid mixture ratio is regulated by the U.S. EPA and many individual states; do not exceed the allowable washer fluid dilution ratios limits that apply. Follow the usage instructions on the washer fluid con‐ tainer. Use BMW’s Windshield Washer Concen‐ trate or the equivalent.◀

Adding washer fluid

Only add washer fluid when the engine is cool, and then close the cover completely to avoid contact between the washer fluid and hot engine parts.

Otherwise, there is a danger of fire and a risk to personal safety if the fluid is spilled.◀

Washer fluid reservoir

All washer nozzles are supplied from one reser‐ voir.

Fill with a mixture of windshield washer con‐ centrate and tap water and – if required – with a washer antifreeze, according to the manufac‐ turer's recommendations.

Mix the washer fluid before adding to find the right mixture.

Do not add windshield washer concentrate and antifreeze undiluted and do not fill with pure water; this could damage the wiper system.

Do not mix window washer concentrates of dif‐ ferent manufacturers because they can clog the windshield washer nozzles.

Recommended minimum fill quantity: 0.2 US gal/1 liter.

Manual transmission

Shifting

Shifting into 5th or 6th gear

When shifting into 5th or 6th gear, push the gearshift lever to the right; otherwise, inad‐ vertent shifting into 3rd or 4th gear could lead to engine damage.◀

Reverse gear

Select only when the vehicle is stationary.

To overcome the resistance push the selector lever dynamically to the left and engage the re‐ verse gear.

Steptronic transmission

Selector lever positions

D Drive

Selector lever position for normal vehicle oper‐ ation. All gears for forward travel are activated automatically.

R is Reverse

Select only when the vehicle is stationary.

N Neutral:

The vehicle may roll. Use in automatic car washes, e.g.

P Park

Select only when the vehicle is stationary. The drive wheels are blocked.

Before exiting the vehicle, make sure that se‐ lector lever position P is set. Otherwise, the ve‐ hicle may begin to move.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 73

Driving

CONTROLS

Kickdown

Kickdown is used to achieve maximum driving performance. Step on the accelerator pedal be‐ yond the resistance point at the full throttle po‐ sition.

Engaging a selector lever position

Press on the brake pedal until you start driving

To prevent the vehicle from creeping after you select a gear, maintain pressure on the brake pedal until you are ready to start.◀

The selector lever can only be taken out of se‐ lector lever position P if the ignition is on or the engine is running.

With the vehicle is stationary, press on the brake pedal before shifting out of selector lever position P or N; otherwise, the selector lever is blocked: shift lock.

A lock prevents inadvertent shifting into selec‐ tor lever position P or R.

Canceling the lock

Sport program and manual mode M/S

Activating the sport program

Press the selector lever to the left out of selec‐ tor lever position D.

The engaged selector lever position, such as S1, is displayed in the instrument cluster.

The sport program of the transmission is acti‐ vated.

Activating the M/S manual mode

Press the selector lever to the left out of se‐

lector lever position D.

2. Push the selector lever forward or back‐

ward.

Manual mode becomes active and the selector lever position is changed.

The engaged selector lever position is displayed in the instrument cluster, for instance M1.

Once maximum engine speed is attained, M/S manual mode is automatically upshifted as needed.

Press button on the front of the selector lever, arrow.

Online Edition for Part no. 01 40 2 961 168 - II/15

Switching to manual mode

▷ To shift down: press the selector lever for‐

ward.

▷ To shift up: pull the selector lever rear‐

wards.

Gears will only be shifted at appropriate engine and road speeds, for example downshifting is not possible if the engine speed is too high.

Page 74

CONTROLS

Driving

The selected gear is briefly displayed in the in‐ strument cluster, followed by the currently se‐ lected gear.

Manual mode M/S: prevent automatic upshifting

Once maximum engine speed is attained, M/S manual mode is automatically upshifted as needed.

For vehicles with Steptronic Sport transmission, automatic shift operations are not performed if one of the following conditions is met:

▷ DSC is deactivated.

▷ TRACTION is activated.

In addition, the kickdown is deactivated.

With the respective transmission version, the lowest possible gear can be selected by simul‐ taneously operating the kickdown and the left shift paddle. However, this effect is not pro‐ duced via the shift paddles when switching briefly from D to manual mode.

Ending the sport program/manual mode

Push the selector lever to the right.

D is displayed in the instrument cluster.

▷ Shift down: briefly pull left shift paddle.

▷ With the respective transmission version,

the lowest possible gear can be selected by pulling and holding the left shift paddle.

Gears will only be shifted at appropriate engine and road speeds, for example downshifting is not possible if the engine speed is too high.

The selected gear is briefly displayed in the in‐ strument cluster, followed by the current gear.

If the shift paddles on the steering wheel are used to shift gears in automatic mode, the transmission temporarily switches to manual mode.

If the selector lever is still in selector lever posi‐ tion D with the respective transmission version, it is possible to switch back into the automatic mode:

▷ Pull and hold right shift paddle.

▷ In addition to the briefly pulled right shift

paddle, briefly pull the left shift paddle.

In the manual mode, after conservative driving for a certain amount of time or if there has been no acceleration or shifting of the shift paddles within a certain amount of time, the transmission switches back to automatic mode.

Shift paddles for Steptronic Sport transmission

The shift paddles on the steering wheel allow you to shift gears quickly while keeping both hands on the steering wheel.

▷ Shift up: briefly pull right shift paddle.

Online Edition for Part no. 01 40 2 961 168 - II/15

Displays in the instrument cluster

The selector lever position is dis‐ played, e.g.: P.

Manually release the transmission lock

Should the selector lever be blocked in selector lever position P despite the ignition being turned on, the brake being depressed and the unlock button being pressed, the transmission lock can be manually canceled:

Page 75

Driving

CONTROLS

Before unlocking the transmission lock man‐ ually, engage the parking brake forcefully to prevent the vehicle from rolling away.

1. Loosen the sleeve of the selector lever.

2. Pull the sleeve over the selector lever. Un‐

plug the cable connector if needed.

3. Using the screwdriver from the onboard ve‐

hicle tool kit, refer to page 197, press the yellow release lever downward, arrow.

4. Move the selector lever slightly toward the

rear; to do this press the unlock button on the front of the selector lever.

Release the release lever.

5. Bring the selector lever into the desired po‐

sition.

Steptronic Sport transmission: Launch Control

The concept

Launch Control enables optimum acceleration on surfaces with good traction.

An experienced driver may be able to achieve better acceleration values in DSC OFF mode, re‐ fer to page 111.

Requirements

Launch Control is available when the engine is warmed up, that is, after uninterrupted driving of at least 6 miles/10 km.

To start with Launch Control do not steer the steering wheel.

Start with launch control

While the engine is running:

1. Press button and select SPORT with

Driving Dynamics Control, refer to page 113.

The instrument cluster displays TRACTION in combination with SPORT. The DSC OFF indicator lamp lights up.

2. Engage selector lever position S.

3. With the left foot, forcefully press down on

the brake.

4. Step on the accelerator pedal beyond the

resistance point at the full throttle position.

A flag symbol is displayed in the instrument cluster.

5. The starting engine speed adjusts. Within

3 seconds, release the brake.

Before using Launch Control, allow the trans‐ mission to cool down for approx. 5 minutes.

Hints

Component wear

Do not use Launch Control too often; oth‐ erwise, this may result in premature wear of components due to the high stress placed on the vehicle.◀

Do not use Launch Control during the break-in, refer to page 154, period.

To increase vehicle stability, activate DSC again as soon as possible.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 76

CONTROLS

Displays

Vehicle features and op‐ tions

This chapter describes all standard, countryspecific and optional features offered with the series. It also describes features that are not

Instrument cluster

Overview, instrument cluster

1 Tachometer 77

2 Messages, e.g. Check Control

3 Speedometer

Online Edition for Part no. 01 40 2 961 168 - II/15

4 Fuel gauge 77

5 Display/reset miles 77

6 Electronic displays 73

Page 77

Electronic displays

Displays

CONTROLS

1 Driver assistance systems

Messages, e.g. Check Control

Time 77

External temperature 77

Selection lists 81

Total miles/trip odometer 77

Check Control

The concept

The Check Control system monitors functions in the vehicle and notifies you of malfunctions in the monitored systems.

A Check Control message is displayed as a com‐ bination of indicator or warning lights and text messages in the instrument cluster and in the Head-up Display.

In addition, an acoustic signal may be output and a text message may appear on the Control Display.

On-board computer 81

2 Selector lever position display 68

Gear shift indicator 79

3 Driving Dynamics Control 113

Status

Indicator/warning lights

General information

The indicator and warning lights can light up in a variety of combinations and colors.

Several of the lights are checked for proper functioning and light up temporarily when the engine is started or the ignition is switched on.

Red lights

Safety belt reminder

Flashing or illuminated: safety belt on the driver or passenger side is not buck‐ led. The safety belt reminder can also

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 78

CONTROLS

Displays

be activated if objects are placed on the front passenger seat.

Make sure that the safety belts are positioned correctly.

Airbag system

Airbag system and belt tensioner are defective.

Have the vehicle checked by the service

center immediately.

Parking brake, brake system

The parking brake is set.

For additional information, refer to Re‐ lease parking brake, refer to page 64.

Front-end collision warning

Illuminated: advance warning is issued, e.g., when there is the impending dan‐ ger of a collision or the distance to the

vehicle ahead is too small.

Increase distance.

Flashing: acute warning of the imminent dan‐ ger of a collision when the vehicle approaches another vehicle at a relatively high differential speed.

Intervention by braking or make an evasive maneuver.

Pedestrian warning

If a collision with a person detected in this way is imminent, the symbol lights up and a signal sounds.

Orange lights

Active Cruise Control

The number bars shows the selected distance from the vehicle driving ahead.

For more information, see Camera-

based cruise control, ACC, refer to page 115.

Vehicle detection, Active Cruise Control

Illuminated: vehicle driving ahead de‐ tected.

Flashing: the conditions are not ade‐

quate for operating the system.

The system was deactivated but applies the brakes until you actively resume control by pressing on the brake pedal or accelerator pedal.

Yellow lights

Anti-lock Braking System ABS

Avoid abrupt braking if possible. Brak‐ ing force boost in some cases defective. Stop carefully. Take into account longer brake travel. Have this checked by the service center immediately.

DSC Dynamic Stability Control

Flashing: DSC controls the drive and braking forces. The vehicle is stabilized. Reduce speed and adapt driving profile

to the driving circumstances.

Illuminated: DSC failed. Have the system checked by the service center.

For additional information, refer to Dynamic Stability Control DSC, refer to page 111.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 79

Displays

CONTROLS

DSC Dynamic Stability Control is deactivated or DTC Dynamic Traction Control is activated

Dynamic Stability Control DSC is switched off or Dynamic Traction Con‐ trol DTC is switched on.

For additional information, refer to Dynamic Stability Control, refer to page 111, and Dy‐ namic Traction Control, refer to page 112.

Flat Tire Monitor FTM

The Flat Tire Monitor signals a loss of tire inflation pressure in a tire.

Reduce your speed and stop cautiously.

Avoid sudden braking and steering maneuvers.

For additional information, refer to Flat Tire Monitor, refer to page 102.

Tire Pressure Monitor TPM

Illuminated: the Tire Pressure Monitor signals a loss of tire inflation pressure in a tire.

Reduce your speed and stop cautiously. Avoid sudden braking and steering maneuvers.

Flashing and then continuously illuminated: no flat tire or loss of tire inflation pressure can be detected.

▷ Interference through systems or devices

with the same radio frequency: after leav‐ ing the area of the interference, the system automatically becomes active again.

▷ TPM could not conclude the reset: perform

the reset of the system again.

▷ A wheel without TPM electronics is fitted:

have the service center check it if needed.

▷ Malfunction: have the system checked by

your service center.

For additional information, refer to Tire Pres‐ sure Monitor, refer to page 98.

Steering system

Steering system in some cases defec‐ tive.

Have the steering system checked by

the service center.

Engine functions

Illuminated: vehicle generates in‐ creased exhaust emissions. It is possible to continue driving. Exhaust system in

some cases defective.

Flashing: increased engine load damages the catalytic converter. Continue driving with a lower engine load. Possible engine problem.

Have the vehicle checked by the service center.

For additional information, refer to On-board Diagnostics socket, refer to page 196.

Green lights

Turn signal

Turn signal on.

Unusually rapid flashing of the indicator lamp indicates that a turn signal bulb

has failed.

For additional information, refer to Turn signal, refer to page 65.

Parking lights, headlight control

Parking lights or headlights are acti‐ vated.

For additional information, refer to Parking lights/low beams, headlight control, re‐ fer to page 90.

Front fog lights

Front fog lights are activated.

For additional information, refer to

Front fog lights, refer to page 93.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 80

CONTROLS

Displays

High-beam Assistant

High-beam Assistant is switched on.

High beams are activated and off auto‐ matically as a function of the traffic sit‐

uation.

For additional information, refer to High-beam Assistant, refer to page 92.

Cruise control

The system is switched on. It maintains the speed that was set using the control elements on the steering wheel.

Blue lights

High beams

High beams are activated.

For additional information, refer to High beams, refer to page 65.

General lamps

At least one Check Control message is displayed or is stored. The symbol is shown in the display of the instrument

cluster.

Text messages

Text messages in combination with a symbol in the instrument cluster explain a Check Control message and the meaning of the indicator and warning lights.

Supplementary text messages

Additional information, such as on the cause of an error or the required action, can be called up via Check Control.

With urgent messages the added text will be automatically displayed on the Control Display.

Symbols

Within the supplementary text, the following functions can be selected independent of the check control message.

▷ Display additional information about

the Check Control message in the Integrated Owner's Manual.

▷ "Service request"

Contact the service partner.

▷ "Roadside Assistance"

Contact Roadside Assistance.

Hiding Check Control messages

Press the onboard computer button on the turn signal lever.

▷ Some Check Control messages are dis‐

played continuously and are not cleared until the malfunction is eliminated. If sev‐ eral malfunctions occur at once, the mes‐ sages are displayed consecutively.

These messages can be faded for approx. 8 seconds. After this time, they are dis‐ played again automatically.

▷ Other Check Control messages are faded

automatically after approx. 20 seconds. They are stored and can be displayed again later.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 81

Displays

CONTROLS

Displaying stored Check Control messages

On the Control Display:

1. "Vehicle info"

2. "Vehicle status"

3. "Check Control"

4. Select the text message.

Messages after trip completion

Special messages displayed while driving are displayed again after the ignition is switched off.

Fuel gauge

Vehicle tilt position may cause the display to vary.

The arrow beside the fuel pump symbol shows which side of the vehicle the fuel filler flap is on.

Notes on refueling, refer to page 170.

Tachometer

Resetting the trip odometer

Press the knob.

▷ The odometer is displayed

when the ignition is switched off.

▷ When the ignition is switched

on, the trip odometer is re‐ set.

External temperature

If the indicator drops to +37 ℉/+3 ℃, a signal sounds.

A Check Control message is dis‐ played.

There is an increased risk of ice

on roads.

Ice on roads

Even at temperatures above

+37 ℉/+3 ℃, roads might be icy.

Therefore, drive carefully on bridges and shaded roads, e.g., to avoid the increased risk of an accident.◀

Always avoid engine speeds in the red warning field. In this range, the fuel supply is interrupted to protect the engine.

Odometer and trip odom‐ eter

The concept

Odometer and trip odometer are displayed in the instrument cluster.

Online Edition for Part no. 01 40 2 961 168 - II/15

Time

The time is displayed in the in‐ strument cluster.

Setting the time on the Control Display, refer to page 84.

Date

The date is displayed in the in‐ strument cluster.

Set the date on the Control Dis‐ play, refer to page 84.

Page 82

CONTROLS

Displays

Range

Display

With a low remaining range:

▷ A Check Control message is

displayed briefly.

▷ The remaining range is

shown on the computer.

▷ With a dynamic driving style - e.g., taking

curves aggressively - engine operation might vary.

The Check Control message appears continu‐ ously below a range of approx. 30 miles/50 km.

Refuel promptly

Refuel no later than at a range of 30 miles/50 km or engine operation might fail and damage might occur.◀

Displaying the cruising range

"Settings"

2. "Instrument cluster"

3. "Range"

Service requirements

The concept

After the ignition is turned on the instrument cluster briefly displays available driving distance or time to the next scheduled maintenance.

Your service specialist can read the current service requirements from your remote control.

Display

Detailed information on service requirements

More information on the scope of service re‐ quired can be displayed on the Control Display.

On the Control Display:

"Vehicle info"

2. "Vehicle status"

3. "Service required"

Required maintenance procedures and le‐ gally mandated inspections are displayed.

4. Select an entry to call up detailed informa‐

tion.

Current fuel consump‐ tion

The concept

Displays the current fuel consumption. Check whether you are currently driving in an efficient and environmentally-friendly manner.

Displaying the current fuel consumption

"Settings"

2. "Instrument cluster"

3. "Current consumption"

Online Edition for Part no. 01 40 2 961 168 - II/15

Symbols

Symbols Description

No service is currently required.

The deadline for scheduled maintenance or a legally man‐ dated inspection is approach‐ ing.

The service deadline has al‐ ready passed.

Entering appointment dates

Enter the dates for the required inspections.

Make sure that the vehicle's date and time are set correctly.

Page 83

Displays

CONTROLS

On the Control Display:

1. "Vehicle info"

2. "Vehicle status"

3. "Service required"

4. "§ Vehicle inspection"

5. "Date:"

6. Adjust the settings.

7. Confirm.

The entered date is stored.

Gear shift indicator

The concept

The system recommends the most fuel efficient gear for the current driving situation.

Depending on the vehicle's features and coun‐ try version of the vehicle, the gear shift indica‐ tor is active in the manual mode of the Step‐ tronic transmission and with manual transmission.

Suggestions to shift gear up or down are dis‐ played in the instrument cluster.

Manual transmission: displaying

Example Description

Fuel efficient gear is set.

Shift into fuel efficient gear.

Steptronic transmission: Displaying

Example Description

Fuel efficient gear is set.

Shift into fuel efficient gear.

Speed limit detection

The concept

Speed limit detection

Speed limit detection uses a symbol in the shape of a traffic sign to display the currently detected speed limit. The camera at the base of the interior rearview mirror detects traffic signs at the edge of the road as well as variable over‐ head sign posts. Traffic signs with extra symbols for wet road conditions, etc. are also detected and compared with the vehicle's onboard data, such as for the rain sensor, and will be dis‐ played depending on the situation.

With the navigation system, the system takes into account the information stored in the navi‐ gation data and also displays speed limits present on routes without signs.

Without a navigation system, the system is sub‐ ject to limitations imposed by technology. Speed limits with extra text characters are al‐ ways displayed.

Hints

Speed limits when towing a trailer are not shown.

Personal judgment

The system cannot serve as a substitute for the driver's personal judgment of the traffic situation.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 84

CONTROLS

Displays

The system assists the driver and does not re‐ place the human eye.◀

At a glance

Camera

The camera is found near the interior rearview mirror.

Keep the windshield in the area behind the in‐ terior rearview mirror clean and clear.

Switching on/off

"Settings"

2. "Instrument cluster"

3. "Speed limit information"

If speed limit detection is switched on, it can be displayed on the info display in the instrument cluster via the computer.

Display

The following is displayed in the instrument cluster:

Speed limit detection

The last speed limit detected.

Without a navigation system the traffic signals are grayed out af‐ ter curves or longer stretches of roadway.

With navigation system: speed limit detection is not available.

Without navigation system: speed limit detection switched on but no speed limit or cancel‐ lation is detected.

Speed limit detection can also be displayed in the Head-up Display.

System limits

The system may not be fully functional and may provide incorrect information in the fol‐ lowing situations:

▷ In heavy fog, rain or snowfall.

▷ When signs are concealed by objects.

▷ When driving very close to the vehicle in

front of you.

▷ When driving toward bright lights.

▷ When the windshield behind the interior

rearview mirror is fogged over, dirty or cov‐ ered by a sticker, etc.

▷ In the event of incorrect detection by the

camera.

▷ If the speed limits stored in the navigation

system are incorrect.

▷ In areas not covered by the navigation sys‐

tem.

▷ When roads differ from the navigation, such

as due to changes in road routing.

▷ When passing buses or trucks with a speed

sticker.

▷ If the traffic signs are non-conforming.

▷ During calibration of the camera immedi‐

ately after vehicle shipment.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 85

Displays

CONTROLS

Selection lists in the in‐ strument cluster

The concept

With the buttons on the steering wheel and the display in the instrument cluster the following can be displayed or operated:

▷ Current audio source.

▷ Redial phone feature.

▷ Turn on voice activation system.

It also displays programs of the Driving Dynam‐ ics Control.

Display

Activating a list and adjusting the setting

Button the steering wheel Function

Activate the respec‐ tive list and select the desired settings.

Confirm the selection.

On-board computer

Calling up information on the info display

Press the onboard computer button on the turn signal lever.

Information is displayed in the info display of the instrument cluster.

Information at a glance

Info display

Repeatedly pressing the button on the turn signal lever calls up the following information in the info display:

▷ Range.

▷ GREEN Info.

When GREEN Mode is activated.

▷ Average fuel consumption.

▷ Current fuel consumption.

▷ Average speed.

▷ Date.

▷ Engine temperature display.

▷ Distance to destination.

When destination guidance is activated in the navigation system.

▷ Time of arrival.

When destination guidance is activated in the navigation system.

▷ Speed limit detection.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 86

CONTROLS

Displays

▷ Speed.

Adjusting the info display

You can select what information from the com‐ puter is to be displayed on the info display of the instrument cluster.

On the Control Display:

1. "Settings"

2. "Instrument cluster"

3. Select the desired displays.

Information in detail

Range

Displays the estimated cruising range available with the remaining fuel.

It is calculated based on your driving style over the last 20 miles/30 km.

GREEN info

Description of GREEN info, refer to page 164.

Average fuel consumption

This is calculated for the period while the en‐ gine is running.

The average fuel consumption is calculated for the distance traveled since the last reset by the on-board comupter.

Average speed

Periods in which the vehicle is parked with the engine manually stopped are not included in the calculation of the average speed.

Resetting average values

Press and hold the onboard computer button on the turn signal lever.

Engine temperature display

Displays the current engine temperature, based on a combination of coolant and motor oil tem‐ perature. As soon as the optimum operating

temperature has been attained, the indicator is in the center position.

If the engine oil or coolant, thus the engine, be‐ come too hot, a Check Control message is dis‐ played.

Check the coolant level, refer to page 193.

Distance to destination

The distance remaining to the destination is displayed if a destination is entered in the navi‐ gation system before the trip is started.

The distance to the destination is adopted au‐ tomatically.

Time of arrival

The estimated time of arrival is displayed if a destination is entered in the navigation system before the trip is started.

The time must be correctly set.

Speed limit detection

Description of the speed limit detection, refer to page 79, function.

Trip computer

The vehicle features two types of board com‐ puters.

▷ "Onboard info": the values can be reset as

often as necessary.

▷ "Trip computer": the values provide an

overview of the current trip.

Resetting the trip computer

On the Control Display:

"Vehicle info"

2. "Trip computer"

3. "Reset": all values are reset.

"Automatically reset": all values are reset approx. 4 hours after the vehicle came to a standstill.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 87

Displays

CONTROLS

Display on the Control Display

Display the computer or trip computer on the Control Display.

On the Control Display:

1. "Vehicle info"

2. "Onboard info" or "Trip computer"

Resetting the fuel consumption and speed

On the Control Display:

1. "Vehicle info"

2. "Onboard info"

3. "Consumpt." or "Speed"

4. "Yes"

Driving Excitement

The concept

On the Control Display, sport instruments can be displayed, and the vehicle condition can be checked before the use of the SPORT program.

Vehicle state

The following vehicle and surrounding area data are automatically checked and evaluated in succession:

▷ Range.

▷ Engine temperature.

▷ External temperature.

▷ SPORT program state.

Finally, a total evaluation of the vehicle state is displayed.

Checking vehicle state

Via onboard monitor:

"Vehicle info"

2. "Driving Excitement"

3. "Vehicle and surroundings"

Via the Driving Dynamics Control

Activating SPORT.

2. "Driving Excitement"

3. "Vehicle and surroundings"

Sport instruments

On the Control Display, values for power and torque are displayed.

Displaying sport instruments

Via onboard monitor:

2. "Driving Excitement"

3. "Sports instruments"

Via the Driving Dynamics Control

2. "Driving Excitement"

3. "Sports instruments"

"Vehicle info"

Activating SPORT.

Online Edition for Part no. 01 40 2 961 168 - II/15

Speed warning

The concept

Displays speed limit which, when reached, should cause a warning to be issued.

The warning is repeated if the vehicle speed drops below the set speed limit once by at least 3 mph/5 km/h.

Displaying, setting or changing the limit

On the Control Display:

"Settings"

2. "Speed"

3. "Warning at:"

Page 88

CONTROLS

Displays

4. Turn the controller until the desired limit is

displayed.

5. Press the controller.

The speed limit is stored.

Activating/deactivating the limit

On the Control Display:

1. "Settings"

2. "Speed"

3. "Warning"

4. Press the controller.

Setting your current speed as the limit

On the Control Display:

"Settings"

2. "Speed"

3. "Select current speed"

4. Press the controller.

The current vehicle speed is stored as the limit.

Settings on the Control Display

Time

Setting the time zone

"Settings"

2. "Time/Date"

3. "Time zone:"

4. Select the desired time zone.

The time zone is stored.

Setting the time

"Settings"

2. "Time/Date"

3. "Time:"

4. Turn the controller until the desired hours

are displayed.

5. Press the controller.

6. Turn the controller until the desired mi‐

nutes are displayed.

7. Press the controller.

The time is stored.

Setting the time format

1. "Settings"

2. "Time/Date"

3. "Format:"

4. Select the desired format.

The time format is stored.

Date

Setting the date

"Settings"

2. "Time/Date"

3. "Date:"

4. Turn the controller until the desired day is

displayed.

5. Press the controller.

6. Make the necessary settings for the month

and year.

The date is stored.

Setting the date format

"Settings"

2. "Time/Date"

3. "Format:"

4. Select the desired format.

The date format is stored.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 89

Displays

CONTROLS

Language

Setting the language

To set the language on the Control Display:

1. "Settings"

2. "Language/Units"

3. "Language:"

4. Select the desired language.

Settings are stored for the profile currently in use.

Setting the voice dialog

Voice dialog for the voice activation system, re‐ fer to page 28.

Units of measure

Setting the units of measure

To set the units for fuel consumption, route/ distance and temperature:

"Settings"

2. "Language/Units"

3. Select the desired menu item.

4. Select the desired unit.

Settings are stored for the profile currently in use.

Brightness

Depending on the light conditions, the bright‐ ness settings may not be clearly visible.

LED ring on the central instrument cluster

The concept

The LED ring displays light animations to repre‐ sent specific functions.

Basic displays

Basic functions, for example the tachometer, can be set to be displayed continually if so de‐ sired.

Event displays

Functions that are only displayed temporarily, for example the volume or temperature set‐ tings, can be set as event displays.

Several vehicle assistance functions can also be displayed on the LED ring. This display corre‐ sponds with the displays of the function in the respective display.

Example: tachometer

Like the tachometer in the instrument cluster, the light animations of the tachometer's basic display show the current RPMs and the respec‐ tive RPM warning margins.

Setting the brightness

To set the brightness of the Control Display:

"Settings"

2. "Control display"

3. "Brightness"

4. Turn the controller until the desired bright‐

ness is set.

5. Press the controller.

Settings are stored for the profile currently in use.

Online Edition for Part no. 01 40 2 961 168 - II/15

Display

▷ Arrow 1: current RPM.

▷ Arrow 2: prewarning field.

Page 90

CONTROLS

Displays

▷ Arrow 3: warning field.

Switching on/off LED ring

1. "Settings"

2. "Center Instrument"

3. "Center Instrument"

Adjusting the LED ring

1. "Settings"

2. "Center Instrument"

3. "Basic display" or "Event display"

4. Select desired setting.

Setting the brightness

The brightness can be adjusted when night lighting is active in the instrument cluster.

"Settings"

2. "Center Instrument"

3. "Brightness"

4. Turn the controller.

Settings are stored for the profile currently in use.

Head-up Display

The concept

Hints

Do not move the moving parts manually

Do not move the moving parts manually, and keep the area of movement of these parts clear; otherwise, the system is damaged.◀

Do not place objects on the Head-up Dis‐

play

Do not place any objects on the Head-up Dis‐ play, attach them to components of the system or insert them in the system, or else the system can be damaged.◀

Keep the closing path clear

Monitor retraction of the projection lens of the Head-up Display and make sure that the closing path is clear; otherwise, injuries may re‐ sult.◀

Follow the instructions for cleaning the Headup Display, refer to page 217.

Display visibility

The visibility of the displays in the Head-up Dis‐ play is influenced by the following factors:

▷ Certain sitting positions.

▷ Objects on the cover of the Head-up Dis‐

play.

▷ Sunglasses with certain polarization filters.

▷ Wet roads.

▷ Unfavorable light conditions.

This system projects important information into the driver's field of vision, e.g., the speed.

The driver can quickly absorb information and concentrate on the traffic situation.

Online Edition for Part no. 01 40 2 961 168 - II/15

Switching on/off

When switching on, the projection lens of the Head-up Display is extended. When switching off, the projection lens of the Head-up Display is retracted again.

Page 91

Press button.

Display

Overview

▷ Speed.

▷ Navigation system.

▷ Check Control messages.

▷ Selection list from the instrument cluster.

▷ Driver assistance systems.

Some of this information is only displayed briefly as needed.

Displays

On the Control Display:

1. "Settings"

2. "Head-Up Display"

3. "Brightness"

4. Turn the controller.

When the low beams are activated, the bright‐ ness of the Head-up Display can be additionally influenced using the instrument lighting, refer to page 93.

Settings are stored for the profile currently in use.

CONTROLS

Adjusting the height

On the Control Display:

"Settings"

2. "Head-Up Display"

3. "Height"

4. Turn the controller.

Settings are stored for the profile currently in use.

Selecting displays in the Head-up Display

On the Control Display:

"Settings"

2. "Head-Up Display"

3. "Displayed information"

4. Select the desired displays in the Head-up

Display.

Settings are stored for the profile currently in use.

Setting the brightness

The brightness is automatically adjusted to the ambient brightness.

The basic setting can be adjusted manually.

Online Edition for Part no. 01 40 2 961 168 - II/15

Setting the rotation

On the Control Display:

"Settings"

2. "Head-Up Display"

3. "Rotation"

4. Turn the controller.

Settings are stored for the profile currently in use.

Chrono package in the cockpit

The concept

The Chrono package consists of three display instruments in the cockpit, where the engine oil pressure, the turbocharger boost, and the time are displayed. In addition, intermediate and to‐

Page 92

CONTROLS

Displays

tal times can be measured using the stop watch.

The display elements of the Chrono package mainly support a sporty driving style, e,g, on racetracks.

Overview

1 Engine oil pressure display

2 Turbocharger boost display

3 Time/stop watch

Engine oil pressure

The current engine oil pressure is displayed.

Turbocharger boost

The current boost of the turbocharger is dis‐ played.

Stop watch

General information

The stop watch contains the following features:

▷ Measuring the total time.

▷ Measuring and storing of up to nine lap

times.

▷ Displaying the time.

The red indicator light indicates that the

stop watch is active.

Overview, buttons

▷ MODE button, arrow 1.

▷ START/STOP button, arrow 2.

▷ RESET/LAP buttons, arrow 3.

Displaying the measured times

The times measured using the stop watch are shown in minutes and seconds on the display. For times greater than 60 minutes, the num‐ bers of hours and the minutes with seconds are alternatively displayed.

If the stop watch is running, the seconds are also shown using a seconds pointer in the scale of the display element.

Measuring the total time

Press button, arrow 2, to start the stop

watch.

2. Press button, arrow 2, again to stop the

stop watch.

Lap times

General information

It is possible to measure and store up to nine lap times. Older lap times are overwritten.

Measuring and storing a lap time

Press button, arrow 2, to start the stop

watch.

2. Press button, arrow 3, to measure and store

a lap time.

The lap time is briefly shown in the display and via the seconds pointer of the stop

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 93

watch, e.g., LAP 1 with the measured time. The stop watch continues running in the background.

3. If needed, press button, arrow 3, again to

measure a further lap time.

Calling up lap times

1. Press button, arrow 1, repeatedly until

LAP 1 is shown on the display.

2. Press button, arrow 2, to call up the individ‐

ual lap times.

Deleting lap times

Press button, arrow 1, repeatedly until

LAP 1 is shown on the display.

2. Press button, arrow 3, to delete all stored

lap times.

Displaying the time

The time is copied from the instrument cluster.

Press button, arrow 1, repeatedly until the time is displayed.

Displays

CONTROLS

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 94

CONTROLS

Lights

Vehicle features and op‐ tions

Overview

1 Rear fog lights

2 Front fog lights

3 Depending on the equipment: automatic

headlight control, cornering lights, Highbeam Assistant, welcome lights, daytime running lights

4 Lights off, daytime running lights

5 Parking lights / daytime running lights

6 Depending on the equipment: low beams,

welcome lights, High-beam Assistant

7 Instrument lighting

Parking lights, corner‐ ing lights and roadside parking lights

General information

Position of switch:

If the driver door is opened with the ignition switched off, the exterior lighting is automati‐ cally switched off at these switch settings.

Parking lights

Position of switch : the vehicle's lights light up on all sides, e.g., for parking.

Do not use the parking lights for extended peri‐ ods; otherwise, the battery may become dis‐ charged and it would then be impossible to start the engine.

When parking you better turn on just the roadside parking light.

Low beams

Position of switch with the ignition switched on: the low beams light up.

Roadside parking lights

The vehicle can be illuminated on one side.

, ,

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 95

Lights

CONTROLS

Switching on

With the ignition switched off, press the lever either up or down past the resistance point for approx. 2 seconds.

Switch off

Briefly press the lever to the resistance point in the opposite direction.

Welcome lights and headlight courtesy de‐ lay feature

Welcome lights

When the vehicle is parked, leave the switch in position come on briefly when the vehicle is unlocked depending on the ambient brightness.

Activating/deactivating

2. "Lighting"

3. "Welcome lights"

Settings are stored for the profile currently in use.

Headlight courtesy delay feature

The low beams stay lit for a short while after the radio-ready state is switched off if the lights are turned off and the headlight flasher is switched on.

Setting the duration

2. "Lighting"

3. "Pathway lighting:"

4. Set length of time.

Settings are stored for the profile currently in use.

or : parking and interior lights

"Settings"

Automatic headlight control

Position of switch vated and off automatically, e.g., in tunnels, in twilight or if there is precipitation. The indicator lamp in the instrument cluster lights up.

A blue sky with the sun low on the horizon can cause the lights to be switched on.

The low beams always stay on when the fog lights are activated.

Personal responsibility

The automatic headlight control cannot serve as a substitute for your personal judg‐ ment in determining when to turn the lights on in response to ambient lighting conditions.

E. g. the sensors are unable to detect fog or hazy weather. To avoid safety risks under these conditions, you should always switch on the lights manually.◀

: the low beams are acti‐

Daytime running lights

With the ignition switched on, the daytime run‐ ning lights light up in position , or

. After the ignition is switched off, the park‐

ing lights light up in position .

Activating/deactivating

In some countries, daytime running lights are mandatory, so it may not be possible to deacti‐ vate the daytime running lights.

On the Control Display:

"Settings"

2. "Lighting"

3. "Daytime running lamps"

Settings are stored for the remote control cur‐ rently in use.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 96

CONTROLS

Lights

Cornering lamp

Position of switch the cornering lamp also lights the interior area of the curve. Below a speed of approx. 25 mph/40 km/h when the flasher is switched on and the steering angle is detected, there is automatic activation.

Malfunction

A Check Control message is displayed.

Cornering light is disrupted or failed. Have the system checked as soon as possible.

: going around corners,

High-beam Assistant

The concept

When the low beams are activated, this system automatically switches the high beams on and off. The procedure is controlled by a camera on the front of the interior rearview mirror. The as‐ sistant ensures that the high beams are acti‐ vated whenever the traffic situation allows. The driver can intervene at any time and switch the high beams on and off as usual.

Note

Personal responsibility

The High-beam Assistant cannot serve as a substitute for the driver's personal judgment of when to use the high beams. Therefore, manually reel off the high beams in situations where required to avoid a safety risk.◀

Activating

The High-beam Assistant can be activated when the low beams are activated.

Depending on the equipment, turn the light

switch into position or .

2. Press button on the turn signal lever, arrow.

The indicator lamp in the instrument cluster lights up.

When the low beams are on, the lights are au‐ tomatically brightened or dimmed.

The system responds to light from oncoming traffic and traffic driving ahead of you, and to adequate illumination, e.g., in towns and cities.

The blue indicator lamp in the instru‐ ment cluster lights up when the system switches on the high beams.

Switching the high beams on and off manually

▷ High beams on, arrow 1.

▷ High beams off/headlight flasher, arrow 2.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 97

Lights

CONTROLS

The High-beam Assistant can be switched off when manually adjusting the light. To reacti‐ vate the High-beam Assistant, press the button on the turn signal lever.

System limits

The system is not fully functional in situations such as the following, and driver intervention may be necessary:

▷ In very unfavorable weather conditions,

such as fog or heavy precipitation.

▷ When detecting poorly-lit road users such

as pedestrians, cyclists, horseback riders and wagons; when driving close to train or ship traffic; and at animal crossings.

▷ In tight curves, on hilltops or in depressions,

in cross traffic or half-obscured oncoming traffic on freeways.

▷ In poorly-lit towns and cities and in the

presence of highly reflective signs.

▷ At low speeds.

▷ When the windshield behind the interior

rearview mirror is fogged over, dirty or cov‐ ered with stickers, etc.

Fog lights

Front fog lights

The low beams must be switched on.

Press button. The green indicator lamp lights up.

Rear fog lights

The low beams or front fog lights must be switched on.

Press button. The yellow indicator lamp lights up.

If the automatic headlight control, refer to page 91, is activated, the low beams will come on automatically when you switch on the rear fog lights.

Instrument lighting

Adjusting

The parking lights or low beams must be switched on to adjust the brightness.

Adjust the brightness with the thumbwheel.

Interior lights

General information

The interior lights, footwell lights, access lights and courtesy lights are controlled automati‐ cally.

Thumb wheel for the instrument lighting con‐ trols brightness of some of these features.

If the automatic headlight control, refer to page 91, is activated, the low beams will come on automatically when you switch on the front fog lights.

When the high beams or headlight flasher are activated, the front fog lights are not switched on.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 98

CONTROLS

Lights

Overview

1 Interior lights

2 Reading lamp

3 Ambient light

Switching the interior lights on and off

Press button.

To reel off permanently: press the button for approx. 3 seconds.

Switch back on: press button.

Reading lights

Press button.

Changing color

Push the switch forward or back: manual color change.

Push and hold the switch forward or back: automatic color change. Push

the switch again to end color changes.

Setting the brightness

The brightness of the ambient light can be ad‐ justed via the thumbwheel for the instrument lighting or on the Control Display.

On the Control Display:

"Settings"

2. "Lighting"

3. "Brightness:"

4. Adjust the brightness.

Reading lights are located in the front next to the interior light.

Ambient light

Depending on your optional features lighting can be adjusted for some lights in the interior.

Activating/deactivating

On the Control Display:

"Settings"

2. "Lighting"

3. "Ambient:"

Settings are stored for the profile currently in use.

Online Edition for Part no. 01 40 2 961 168 - II/15

Page 99

Safety

CONTROLS

Vehicle features and op‐ tions

This chapter describes all standard, countryspecific and optional features offered with the series. It also describes features that are not

Airbags

1 Front airbag, driver

2 Front airbag, front passenger

3 Head airbag

Front airbags

Front airbags help protect the driver and front passenger by responding to frontal impacts in which safety belts alone would not provide ad‐ equate restraint.

Online Edition for Part no. 01 40 2 961 168 - II/15

4 Side airbag

5 Knee airbags

Side airbags

In a lateral impact, the side airbag supports the side of the body in the chest and lap area.

Head airbags

In a lateral impact, the head airbag supports the head.

Page 100

CONTROLS

Safety

Knee airbag

The knee airbag supports the legs in a frontal impact.

Protective action

Airbags are not triggered in every impact situa‐ tion, e.g., in less severe accidents or rear-end collisions.

Information on how to ensure the opti‐ mal protective effect of the airbags

▷ Keep at a distance from the airbags.

▷ Always grasp the steering wheel on the

steering wheel rim, holding your hands at the 3 o'clock and 9 o'clock positions, to keep the risk of injury to your hands or arms as low as possible when the airbag is triggered.

▷ There should be no person, animals, or ob‐

jects between an airbag and a person.

▷ Do not use the cover of the front airbag on

the front passenger side as a storage area.

▷ Dashboard and windshield on the front

passenger side must stay clear - do not at‐ tach adhesive labels or coverings and do not attach brackets or cables, e. g., for GPS devices or' mobile phones.

▷ Make sure that the front passenger is sitting

correctly, i.e., keeps his or her feet and legs in the footwell; otherwise, leg injuries might occur when front airbag is activated.

▷ Do not place slip covers, seat cushions or

other objects on the front passenger seat that are not approved specifically for seats with integrated side airbags.

▷ Do not hang pieces of clothing, such as

jackets, over the backrests.

▷ Make sure that occupants keep their heads

away from the side airbag and do not rest against the head airbag; otherwise, injuries might occur when airbag is activated.

▷ Do not remove the airbag system.

▷ Do not remove the steering wheel.

▷ Do not apply adhesive materials to the air‐

bag cover panels, do not cover them or modify them in any way.

▷ Never modify either the individual compo‐

nents or the wiring in the airbag system. This also applies to steering wheel covers, the dashboard, the seats, the roof pillars and the sides of the roofliner.◀

Even when you follow all instructions very closely, injury from contact with the airbags cannot be ruled out in certain situations.

The ignition and inflation noise may lead to short-term and, in most cases, temporary hear‐ ing impairment in sensitive individuals.

Malfunction, deactivation and after de‐ ploying the airbags

Do not touch the individual components imme‐ diately after the system has been triggered; otherwise, you may risk burns.

Only have the airbags checked, repaired or dis‐ mantled and the airbag generator scrapped by the service center or an authorized repair shop for handling explosives.

Non-professional attempts to service the sys‐ tem could lead to failure in an emergency or unintentional activation of the airbag - both may lead to injury.◀

Warnings and information on the airbags are also found on the sun visors.

Functional readiness of the airbag system

When the ignition is reel on, the warn‐ ing lamp in the instrument cluster lights

up briefly and thereby indicates the op‐ erational readiness of the entire airbag system and the belt tensioner.

Airbag system malfunctioning

▷ Warning lamp does not come on when the

ignition is turned on.

▷ The warning lamp lights up continuously.

Online Edition for Part no. 01 40 2 961 168 - II/15

MINI Hardtop 2 Door With Connected 2015, Hardtop 4 Door With Connected 2015 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Cockpit

All around the steering wheel

All around the center console

All around the roofliner

Onboard monitor

The concept

Control elements at a glance

Operating concept

Touchpad

Example: setting the clock

Status information

Split screen

Programmable memory buttons

Deleting personal in the vehicle

Entering letters and numbers

Voice activation system

The concept

Requirements

Using voice activation

Possible commands

One example: open the tone settings

Setting the voice dialog

Adjusting the volume

Integrated Owner's Manual in the vehicle

Integrated Owner's Manual in the vehicle

Opening and closing

Remote control/key

Personal Profile

Without remote control

Tailgate

Comfort Access

Adjusting

Alarm system

Power windows

Adjusting

Sitting safely

Seats

Safety belts

Front head restraints

Rear head restraints

Mirrors

Steering wheel

Transporting children safely

The right place for children

LATCH child restraint system

Driving

Start/Stop button

Starting the engine

Engine stop

Auto Start/Stop function

Parking brake

Turn signal, high beams, headlight flasher

Washer/wiper system

Washer fluid

Manual transmission

Steptronic transmission

Displays

Instrument cluster

Check Control

Fuel gauge

Tachometer

External temperature

Time

Date

Range

Service requirements

Gear shift indicator

Speed limit detection

On-board computer

Driving Excitement

Speed warning

Settings on the Control Display

LED ring on the central instrument cluster

Head-up Display

Chrono package in the cockpit

Lights