MINI Hardtop 2 Door With Connected 2009 Owner's Manual

Contents

A - Z

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

OWNER'S MANUAL

MINI

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Cooper

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Cooper S

John Cooper

Works

Congratulations on your new MINI

This Owner's Manual should be considered a permanent part of
this vehicle. It should stay with the vehicle when sold to provide
the next owner with important operating, safety and mainte­nance information.

We wish you an enjoyable driving experience.

© 2008 Bayerische Motoren Werke

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Aktiengesellschaft
Munich, Germany
Reprinting, including excerpts, only with the
written consent of
BMW AG, Munich.
US English VIII/08, 08 03 450
Printed on environmentally friendly paper,
bleached without chlorine, suitable for recycling.

CONTENTS

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The fastest way to find information on a particu­lar topic or item is by using the index, refer to
page 198.

Using this Owner's Manual

4 Notes
6 Reporting safety defects

AT A GLANCE

10 Cockpit
16 Onboard monitor
21 Voice command system

CONTROLS

26 Opening and closing
36 Adjustments
42 Transporting children safely
44 Driving
53 Everything under control
68 Technology for driving comfort and safety
80 Lamps
84 Climate
87 Practical interior accessories

DRIVING TIPS

94 Things to remember when driving

MOBILITY

152 Refueling
154 Wheels and tires
163 Under the bonnet
167 Maintenance
169 Care
173 Replacing components
183 Giving and receiving assistance

REFERENCE

190 Technical data
193 Short commands for the voice command

system

198 From A to Z

NAVIGATIONREFERENCE

NAVIGATION

102 Starting the navigation system
104 Destination entry
116 Destination guidance
125 What to do if …

ENTERTAINMENT

128 On/off and settings
131 Radio
139 CD player and CD changer
145 AUX-In port
146 USB-audio interface

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

3

Notes

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Using this Owner's

Notes

Manual

We have tried to make all the information in this
Owner's Manual easy to find. The fastest way to
find specific topics is to refer to the detailed
index at the back of the manual. If you wish to
gain an initial overview of your vehicle, you will
find this in the first chapter.

Should you wish to sell your MINI at some time in
the future, remember to hand over this Owner's
Manual to the new owner; it is an important part
of the vehicle.

Additional sources of information

Should you have any other questions, your MINI
Dealer will be glad to advise you at any time.

You can find more information about the MINI,
for example on its technology, on the Internet at
www.MINI.com.

Symbols used

Indicates precautions that must be fol­lowed precisely in order to avoid the pos-

sibility of personal injury and serious damage to
the vehicle.<

Indicates information that will assist you in
gaining the optimum benefit from your

vehicle and enable you to care more effectively
for your vehicle.<

Refers to measures that can be taken to
help protect the environment.<

< Marks the end of a specific item of informa-

tion.

*

Indicates special equipment, country-specific
equipment and optional extras, as well as equip­ment and functions not yet available at the time
of printing.

"..." Identifies Control Display texts used to
select individual functions.

{...} Verbal instructions to use with the voice
command system.

{{...}} Identifies the answers generated by the
voice command system.

Symbols on vehicle components

Indicates that you should consult the rele­vant section of this Owner's Manual for

information on a particular part or assembly.

The individual vehicle

The manufacturer of your MINI is the Bayerische
Motoren Werke Aktiengesellschaft, BMW AG.

When you ordered your MINI, you chose various
items of equipment. This Owner's Manual
describes the entire array of options and equip­ment that the manufacturer of your MINI makes
available with a specific model range.

Bear in mind that the manual may contain infor­mation on accessories and equipment that you
have not specified for your own vehicle. Sections
describing options and special equipment are

*

marked by asterisks
possible differences between the descriptions in
this manual and your own vehicle's equipment.

If your MINI features eq uipment not described in
this Owner's Manual, observe the enclosed Sup­plementary Owner's Manuals.

to assist you in identifying

Editorial notice

The manufacturer pursues a policy of continu­ous, ongoing development that is conceived to
ensure that MINI vehicles continue to embody
the highest quality and safety standards com­bined with advanced, state-of-the-art technol­ogy. For this reason, it is possible in exceptional
cases that features described in this Owner's
Manual could differ from those on your vehicle.

4

For your safety

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Maintenance and repair

Advanced technology, e.g. the use of mod-

ern materials and powerful electronics,
requires specially adapted maintenance and
repair methods. Therefore, have the necessary
work on your MINI only carried out by a MINI
Dealer or a workshop that has specially trained
personnel working in accordance with the speci­fications of the MINI manufacturer. If this work is
not carried out properly, there is a danger of sub­sequent damage and related safety hazards.<

within the vehicle without using an externally
mounted antenna, or transceiver eq uipment, for
instance, CBs, walkie-talkies, ham radios or sim­ilar accessories, may cause extensive damage to
the vehicle, compromise its safety, interfere with
the vehicle's electrical system or affect the valid­ity of the MINI Limited Warranty. See your MINI
Dealer for additional information.<

Maintenance, replacement, or repair of

the emission control devices and systems
may be performed by any automotive repair
establishment or individual using any certified
automotive part.<

Parts and accessories

For your own safety, use genuine parts
and accessories approved by the manu-

facturer of the MINI.

When you purchase accessories tested
and approved by the manufacturer of the MINI
and Original MINI Parts, you simultaneously
acquire the assurance that they have been thor­oughly tested by the manufacturer of the MINI
to ensure optimum performance when installed
on your vehicle.

The manufacturer of the MINI warrants these
parts to be free from defects in material and
workmanship.

The manufacturer of the MINI will not accept any
liability for damage resulting from installation of
parts and accessories not approved by the man­ufacturer of the MINI.

The manufacturer of the MINI cannot test every
product made by other manufacturers to verify
if it ca n be us ed on a MINI s afel y and withou t ris k
to either the vehicle, its operation, or its occu­pants.

Original MINI Parts, MINI Accessories and other
products approved by the manufacturer of the
MINI, together with professional advice on using
these items, are available from all MINI Dealers.

Installation and operation of non-MINI
approved accessories such as alarms, radios,
amplifiers, radar detectors, wheels, suspension
components, brake dust shields, telephones,
including operation of any mobile phone from

California Proposition 65 warning

California law requires us to issue the following
warning:

Engine exhaust and a wide variety of

automobile components and parts,
including components found in the interior fur­nishings in a vehicle, contain or emit chemicals
known to the State of California to cause cancer
and birth defects and reproductive harm. In
addition, certain fluids contained in vehicles and
certain products of component wear contain or
emit chemicals known to the State of California
to cause cancer and birth defects or other repro­ductive harm.

Battery posts, terminals and related accessories
contain lead and lead compounds. Wash your
hands after handling.

Used engine oil contains chemicals that have
caused cancer in laboratory animals. Always
protect your skin by washing thoroughly with
soap and water.<

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT NAVIGATIONREFERENCE

5

Service and warranty

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Reporting safety defects

We recommend that you read this publication
thoroughly.

Your MINI is covered by the following warran-

Notes

ties:

> New Vehicle Limited Warranty

> Rust Perforation Limited Warranty

> Federal Emissions System Defect Warranty

> Federal Emissions Performance Warranty

> California Emission Control System Limited

Warranty

Detailed information about these warranties is
listed in the Service and Warranty Information
Booklet for US models or in the Warranty and
Service Guide Booklet for Canadian models.

For US customers

The following applies only to vehicles owned
and operated in the US.

If you believe that your vehicle has a defect
which could cause a crash or could cause injury
or death, you should immediately inform the
National Highway Traffic Safety Administration,
NHTSA, in addition to notifying MINI of North
America, LLC, P.O. Box 1227, Westwood, New
Jersey 07675-1227, Telephone [phone]-

1117.

If NHTSA receives similar complaints, it may
open an investigation, and if it finds that a safety
defect exists in a group of vehicles, it may order
a recall and remedy campaign. However, NHTSA
cannot become involved in individual problems
between you, your dealer, or MINI of North
America, LLC.

To contact NHTSA, you may call the Vehicle
Safety Hotline toll-free at 1-888-327-4236
(TTY: 1-800-424-9153);
go to http://www.safercar.gov; or write to:
Administrator, NHTSA, 400 Seventh Street, SW.,
Washington, DC 20590. You can also obtain
other information about motor vehicle safety
from http://www.safercar.gov

For Canadian customers

Canadian customers who wish to report a
safety-related defect to Transport Canada,
Defect Investigations and Recalls, may call
1-800-333-0510 toll-free from anywhere in
Canada or 1-613-993-9851 from the Ottawa
region and from other countries, or contact
Transport Canada by mail at: Transport Canada,
ASFAD, Place de Ville, Tower C, 330 Sparks
Street, Ottawa, ON, K1A 0N5.

You can also obtain other information about
motor vehicle safety from http://www.tc.gc.ca

6

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT NAVIGATIONREFERENCE

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

7

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

AT A GLANCE

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

AT A GLANCE

CONTROLS

DRIVING TIPS

NAVIGATION

ENTERTAINMENT

MOBILITY

REFERENCE

Cockpit

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Around the steering wheel: Controls and displays

Cockpit

1 Adjusting the exterior mirrors, folding them

*

in and out

2

10

40

Parking lamps 80

Low beams 80

Automatic headlamp control

Turn signals 48

*

80

High beams 81

Headlamp flasher 48

Roadside parking lamps

Computer

*

54

*

81

3 Tachometer 12

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Instrument lighting 82

Resetting the trip odometer 53

4

5

6 Ignition lock 44

7 Buttons

Wiper system 49

Switching the ignition on/off and
starting/stopping the engine 44

*

on steering wheel

Continuing cruise control

Right:
Storing speed and accelerating or
decelerating

Left:
Volume

Activating/deactivating cruise
control

Telephone

> Press: accepting and ending a

call, starting dialing
selected phone number and
redialing if no phone number is
selected

> Press longer: redialing

*

51

*

51

*

:

*

of

NAVIGATIONREFERENCE

Activating/deactivating voice com-

*

mand system

Changing radio station
Selecting music track
Scrolling through phone book and
lists with stored phone numbers

8 Horn: the entire surface

9 Adjusting the steering wheel 41

10 Releasing the bonnet 163

21

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

11

Displays

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Cockpit

1 Tachometer 53

with indicator and warning lamps 13

2 Display for

> Clock 53

> Outside temperature 53

> Current vehicle speed 53

> Indicator and warning lamps 13

3 Resetting the trip odometer 53

4 Display for

> Position of automatic transmission

> Computer

> Date of next scheduled service, and

remaining distance to be driven 58

> Odometer and trip odometer 53

> Initializing the Flat Tire Monitor

> Resetting the Tire Pressure Monitor

> Settings and information 57

> Personal Profile settings 26

5 Instrument lighting 82

6 Speedometer

with indicator and warning lamps 13

7 Control Display 16

8 Fuel gauge 54

*

54

*

46

*

72

*

75

12

Indicator and warning

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

lamps

The concept

In urgent cases, this information will be shown
as soon as the corresponding lamp comes on.

Indicator lamps without text messages

The following indicator lamps in display area 1
indicate certain functions:

High beams/headlamp flasher 81

Indicator an d warning lamps can light up in various
combinations and colors in indicator area 1 or 2.

Some lamps are checked for proper functioning
and thus come on briefly when the engine is
started or the ignition is switched on.

Explanatory text messages

Text messages at the lower edge of the Control
Display explain the meaning of the displayed
indicator and warning lamps.

Fog lamps

Rear fog lamp

Lamp flashes:
DSC or DTC is regulating the drive
forces in order to maintain driving
stability 69

Parking brake applied 46

Engine malfunction with adverse effect
on exhaust emissions 168

Cruise control 51

Turn signals 48

*

82

*

82

NAVIGATIONREFERENCE

You can call up more information, e.g. on the
cause of a malfunction and on how to respond,
via Check Control, page 63.

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

13

Around the center console

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Cockpit

14

1 Microphone for voice command system

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

and for telephone in hands-free mode

2 Indicator/warning lamp* for front passen-

ger airbags 79

3

Reading lamps

*

83

*

*

Defrosting windows 86

*

Cooling function

Rear window defroster 86

86

Color of ambient lighting

Glass sunroof, electric

Interior lamps 83

4 Hazard warning flashers

5 Speedometer 12

6 Drive for audio CDs

7 Cover of navigation DVD drive 102

> Switching audio sources on/off and

adjusting volume

Changing the radio station or track

Changing the audio source

Changing the frequency

8 Automatic climate control

Temperature 86

Air distribution to the
windshield 86

Air distribution to the upper body
area 86

*

*

34

83

Windshield heating 86

9 Switches in center console

*

Seat heating

Power windows 35

Rear fog lamp

Central locking system, inside 30

Fog lamps

10 AUX-In port, USB-audio

interface

11 Driving stability control systems

> Dynamic Stability Control DSC 69

> Dynamic Traction Control

12 Changing to a different menu on the Control

Display 18

13 MINI joystick 16

Move in four directions, turn or press

14 Opening the start menu on the Control

Display 17

15 Sport button

*

145, 146

*

71

39

*

82

*

82

DTC* 70

NAVIGATIONREFERENCE

Air distribution to the footwell 86

Automatic air distribution and flow
rate 85

Automatic recirculated-air control
AUC and recirculated-air mode 85

Maximum cooling 85

Air flow rate 85

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

15

Onboard monitor

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The onboard monitor integrates the functions of
a large number of switches. This allows these
functions to be operated from a single central
position. The following section provides an

Controls

Onboard monitor

introduction to basic menu navigation. The con­trol of the individual functions is described in
connection with the relevant equipment.

1 Control Display 16

2 MINI joystick

The MINI joystick can be used to select menu
items and to adjust settings:

> Move in four directions, arrows 5

> Turn, arrow 6

> Push, arrow 7

3 Opening start menu 17

4 Changing to another menu 18

Operate the MINI joystick only when traf­fic and road conditions allow this, to avoid

endangering the car's occupants and other road
users by being distracted.<

16

Menu overview

Navigation

> Navigation system

> Onboard information, e.g. for displaying the

average fuel consumption

Communication*

> Telephone, refer to separate Owner's Manual

Entertainment

> Radio

> CD player and CD changer

> AUX-In port, USB-audio interface* for

external audio device

*

Setup

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

> Switching off Control Display

> Tone and display settings

> Settings for your vehicle, e.g. for the central

locking system

> Display of service requirements and dates

for statutory emissions and vehicle inspec­tions

> Check Control

Operating principle

As of radio readiness, the following message
appears on the Control Display:

Opening start menu

Press the button.

To open the start menu from the Setup menu:
Press the button twice.

Calling up menu items in the start menu

Via the start menu you can call up the four menu
items of Navigation, Communication, Entertain­me nt and Setu p: mov e the MINI jo ysti ck fo rward
or backward or press it. Depending on the selec­tion, the menu last opened is displayed.

To hide the message:
Press the MINI joystick.
The start menu is displayed.

The message is automatically hidden after
approx. 10 seconds.

Start menu

All onboard monitor functions can be called up
via four menu items.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

17

Changing between menu items

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Press the button.

Pressing the button repeatedly opens the Com­munication, Navigation and Entertainment
menu items in succession. The screen that was
last open is displayed.

Displays in menu

Onboard monitor

1 Each menu is subdivided into fields.

2 White symbol: the field is active.

Gray symbol: the field is inactive.

1 Menu items are usually grouped in horizon-

tal or vertical lists.

2 Additional menu items can be selected in

this field.

3 Settings are represented graphically or as

numerical values.

4 A curved line shows that menu items can be

selected in lists. The beginning and end of a
list are each marked by a circle.

18

Operating principle at a glance

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The following is a general description of opera­tions using the onboard monitor.

For an exemplary step-by-step application, refer
to Setting the time, page 61.

1 Highlighting a menu item:

> Turn the MINI joystick; the highlight

marker moves

> Menu items that are displayed in color on

the Control Display can be highlighted

2 Confirming a menu item:

> Press the MINI joystick

> New menu items are displayed or the

function is executed

> Select a function by highlighting and con-

firming it

3 Highlighting a menu item: refer to 1

4 Switching between fields:

> Briefly move the MINI joystick to the left,

right, forward or backward

> Release the MINI joystick

5 Adjusting settings:

> Turn the MINI joystick

> Graphic display, numerical value or text

displays can be changed

> Confirm by switching to another field

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

19

Status information

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

1 Display for:

> Entertainment:

Radio, CD and external audio source

Onboard monitor

> Telephone

Name of the connected mobile phone,
network search or no network

2 Entertainment audio output off or

display for traffic information

> "TI":

Reception of traffic information for the navi­gation system is possible and is switched on

3 Display for:

> New entries present in "Missed

calls

> Roaming active

4 It is possible to make calls

phone is paired with the vehicle

Reception strength of mobile phone

network, depending on mobile phone

5 Time

Other displays:
Status information is temporarily hidden during
Check Control message displays or entries via
the voice command system

"*

*

in "Communication":

*

*

*

.

*

:

if the mobile

switching Control Display off/on

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Display off".

or

To switch on, press the MINI joystick.

20

Voice command system

*

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The concept

The voice command system allows you to con­trol operation of various vehicle systems without
removing your hands from the steering wheel.

Individual menu items on the Control Display
can be spoken as commands. It is not necessary
to use the MINI joystick.

The voice command system transforms oral
commands into control signals for the selected
systems and provides support in the form of
instructions or questions.

Precondition

Via the onboard monitor, select the language in
which the voice command system is operating,
so that the spoken commands can be identified.
Setting the onboard monitor language, page 67.

Symbols in the Owner's Manual

{...} Say the specified commands word for
word.
{{...}} Indicates responses of the voice com­mand system.

This symbol on the Control Display and an
acoustic signal indicate that the voice com­mand system is ready to receive spoken
commands.

2. Say the command.

The command appears on the Control Dis­play.

NAVIGATIONREFERENCE

Saying commands

Activating voice command system

1. Press the button on the steering wheel.

This symbol is displayed on the Control Dis­play when you can enter additional commands.
If no further commands are possible, continue
by operating the item of equipment via the
onboard monitor.

Terminating or canceling voice
command system

Press the button on the steering wheel or

{Cancel}

21

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

Commands

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Having the possible commands read
aloud

You can have the system read aloud the possible
commands related to the selected menu item
on the Control Display.
Having the possible commands read aloud:

{Options}

For instance, if you have selected "CD", the com­mands available for operating the CD player and
CD changer are read out.

Opening help

{Help}

Using alternative commands

There are often a number of commands to run a
function, e.g.:

Voice command system

{Radio on} or {Turn radio on}

Calling up functions immediately via
short commands

Short commands enable you to perform certain
functions immediately, irrespective of which
menu item is selected, page 193.

Opening the start menu

{Main menu}

Example: selecting a track

1. Press the button on the steering wheel.

2. {Entertainment}

The system says:
{{Entertainment}}

3. {CD}

The system says:
{{CD on}}

22

4. Press the button on the steering wheel.

5. Select a track, e.g.:

{Track 1}
The system says:
{{Track 1}}

Notes

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

For information on voice control of the
telephone, refer also to the separate

Owner's Manual.<

For voice commands, bear in mind the follow­ing:

> Pronounce the commands and digits

smoothly and at normal volume, avoiding
excessive emphases and pauses. The same
applies to spelling when entering a destina­tion for navigation.

> Always speak the commands in the lan-

guage of the voice command system.

> When selecting a radio station, use the stan-

dard pronunciation of the station name.

> Keep the doors, windows and glass sunroof

closed to prevent interference from outside
noise.

> Avoid ambient noise in the vehicle while

speaking.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

23

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

AT A GLANCE

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

CONTROLS

CONTROLS

DRIVING TIPS

NAVIGATION

ENTERTAINMENT

MOBILITY

REFERENCE

Opening and closing

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Keys/remote controls

Remote control

Each remote control contains a rechargeable
battery that is recharged when it is in the igni-

Opening and closing

tion lock while the car is being driven. You
should therefore use each remote control at
least twice a year to maintain the charge status.
In vehicles equipped with convenient access
the remote control contains a replaceable bat­tery, page 34.

If more than one remote control is used, the set­tings called up and implemented depend on
which remote control is recognized when the
car is unlocked, refer to Personal Profile,
page 26.

In addition, information about service require­ments is stored in the remote control, refer to
Service data in the remote control, page 167.

New remote controls

Your MINI Dealer can supply new remote con­trols as additional units or as replacements in the
event of loss.

Integrated key

Press button 1 to release the key.

The integrated key fits the following locks:

> Driver's door, page 29

Personal Profile

*

,

The concept

The functions of your MINI can be set individu­ally. By means of Personal Profiles, most of these
settings are stored for the remote control cur­rently in use. When you unlock the car, the
remote control is recognized and the settings
stored for it are called up and implemented.

This means that your settings will be activated
for you, even if in the meantime your car was
used by someone else with another remote con­trol and the corresponding settings.

At most three remote controls can be set for
three different people. A prerequisite is that
each person uses a separate remote control.

Personal Profile settings

For more information on specific settings, refer
to the specified pages.

> Response of the central locking system

when the car is being unlocked 27

> Automatic locking of the vehicle 30

> Triple turn signal activation 48

26

> Settings for the displays on the onboard

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

monitor, in the speedometer and in the
tachometer.

> 12h/24h mode of the clock 62

> Date format 63

> Brightness of the Control Display 67

> Language on the Control Display 67

> Units of measure for fuel consumption,

distance covered/remaining distances
and temperature 58

> Show visual warning for Park Distance Con-

trol PDC

> Light settings:

> Pathway lighting 80

> Daytime running lamps 81

> Automatic climate control: AUTO program,

activating/deactivating cooling function and
automatic recirculated-air control, setting
temperature, air flow rate and
distribution 85

> Entertainment:

> Audio volume 129

> Tone control 129

> Speed-dependent volume control 130

*

68

> In cars with convenient access*, via the door

handles on the driver's and passenger's
sides

The anti-theft system is also operated at the
same time. It prevents the doors from being
unlocked using the lock buttons or door han­dles. The remote control can also be used to
switch on/off the welcome lamps and interior

*

lamps. The alarm system
deactivated (page 31).

is also activated or

Operating from inside

Button for central locking system, page 30.

In the event of a sufficiently severe accident, the
central locking system unlocks automatically. In
addition, the hazard warning flashers and inte­rior lamps come on.

Opening and closing: from outside

Persons or animals in a parked vehicle

could lock the doors from the inside. Take
the key with you when you leave the vehicle so
that the vehicle can be opened from the out­side.<

NAVIGATIONREFERENCE

Central locking system

The concept

The central locking system is ready for operation
whenever the driver's door is closed.

The system simultaneously engages and
releases the locks on the following:

> Doors

> Tailgate

> Fuel filler door

Operating from outside

> Via the remote control

> Via the door lock

*

Using the remote control

Unlocking

Press the button.
The welcome lamps and interior lamps come on.

Unlocking mode

You can also set which parts of the car are
unlocked. The setting is stored for the remote
control in use.

Onboard monitor, for operating principle refer
to page 16.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

27

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

3. Select "Settings".

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

4. Select "Vehicle and tires".

5. Select "Door locks".

Opening and closing

6. Select "Central locking".

7. Select "Unlock button".

8. Select a menu item:

> "All doors"

Press the button once to unlock
the entire vehicle.

> "Driver's door"

Press the button once to unlock
only the driver's door and the fuel filler
door.
Press the button twice to unlock the
entire vehicle.

Convenient opening

Hold the button down.
The power windows are opened and the glass

*

sunroof

is raised.

Convenient closing is not possible by
means of the remote control.<

Locking

Press the button.

Do not lock the vehicle from the outside if
there is any person inside, because the

vehicle cannot be unlocked from inside without
special knowledge.<

Setting confirmation signals

To have the vehicle confirm when it has been
locked or unlocked.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Vehicle and tires".

5. Select "Door locks".

6. Select "Confirmation".

28

7. Select the desired signal.

The signal is activated.

Acoustic signals can be selected in vehicles with
an alarm system.

Switching on interior lamps

While the car is locked:
Press the button.
You can also use this function to locate your
vehicle in parking garages, etc.

Unlocking the tailgate

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Press the button.

When it is opened, the tailgate swings

upward and outward to the rear. Ensure
that there is sufficient clearance.
To prevent accidentally locking yourself out, do
not place the key down in the cargo bay. If the
tailgate was locked before opening, it will be
locked again after it is closed.
Before and after each trip, check that the tail­gate has not been inadvertently unlocked.<

Malfunctions

The remote control may malfunction due to
local radio waves. If this occurs, unlock and lock
the car at the door lock with the integrated key.

If the car can no longer be locked with a remote
control, the battery in the remote control is dis­charged. Use this remote control during an
extended drive; this will recharge the battery,
page 26.

For US owners only

The transmitter and receiver units comply with
part 15 of the FCC/Federal Communications
Commission regulations. Operation is governed
by the following:

FCC ID:
LX8766S
LX8766E
LX8CAS

Compliance statement:
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:

> This device must not cause harmful interfer-

ence, and

> This device must accept any interference

received, including interference that may
cause undesired operation.

Any unauthorized modifications or

changes to these devices could void the
user's authority to operate this equipment.<

Using the door lock

You can set which parts of the car are unlocked,
page 27.

When there is no alarm system

*

nient access

locked with the door lock.<

To lock all doors, the fuel filler door and the tail­gate together:

With the doors closed, press the interior central
locking button (page 30) to lock the vehicle.

Unlocking and opening the driver or passenger
door, page 30.

Locking the vehicle.

> Lock the driver's door with the integrated

key via the door lock, or

> press the safety lock button on the pas-

senger's door and close the door from
the outside.

, only the driver's door is

*

or conve-

Convenient operation

With an alarm system* or convenient access*,

*

the windows and glass sunroof
ated via the door lock.

Hold the key in the position for unlocking or
locking.

Watch during the closing process to be
sure that no one is injured. Releasing the

key stops the operation.<

can be oper-

Manual operation

In the event of an electrical malfunction, the
driver's door can be unlocked or locked by turn­ing the integrated key in the door lock to the end
positions.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

29

Opening and closing:

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

from inside

The switch locks or unlocks the doors and tail­gate when the doors are closed, but the anti­theft system is not activated. The fuel filler door

*

remains unlocked

Unlocking and opening

Opening and closing

> Either unlock the doors together using the

switch for the central locking system and
then pull the door handle above the armrest
or

> pull on the door handle of either door twice:

the first time unlocks the door, the second
time opens it.

Locking

> Press the switch or

> press down the safety lock button of a door.

To prevent you from being locked out, the
open driver's door cannot be locked using
the lock button.

Persons or animals in a parked vehicle

could lock the doors from the inside. Take
the key with you when you leave the vehicle so
that the vehicle can be opened from the out­side.<

Automatic locking

You can also set the situations in which the car
locks. The setting is stored for the remote con­trol in use.

.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Vehicle and tires".

5. Select "Door locks".

6. Select "Central locking".

7. Select a menu item:

> "Relock if not opened"

The central locking system automatically
locks the vehicle after a short time when
no door has been opened.

> "Lock after driving"

The central locking system automatically
locks the vehicle as soon as you drive off.

The setting is selected.

The setting is stored for the remote control cur­rently in use.

Tailgate

To avoid damage, make sure there is suf­ficient clearance before opening the tail-

gate.<

Opening

In some national-market versions, the tail­gate cannot be unlocked using the remote

control unless the vehicle is unlocked first.<

30

Press the button in the handle, arrow, or the

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

button of the remote control, for an
extended period. The tailgate is unlocked and
can be opened.

Closing

Make sure that the closing path of the tail­gate is clear, otherwise injuries may

occur.<

The handle recesses on the interior trim panel of
the tailgate make it easier to pull it down.

Alarm system*

> An acoustic alarm

> Switching on the hazard warning flashers

Arming and disarming

Whenever the car is locked or unlocked, the
alarm system is armed or disarmed.

Even when the alarm system is armed, you can
open the tailgate by means of the button
on the remote control.
When you subsequently close the tailgate it is
again locked and monitored.

On certain national-market versions,
unlocking via the door lock triggers off the

alarm.<

Panic mode*

You can activate the alarm system if you find
yourself in a dangerous situation.

Press the button for at least two seconds.

Switching off the alarm:
Press any button.

Switching off an alarm

> Unlock the car with the remote control.

> Insert the key fully into the ignition lock.

> In cars with convenient access

button on the door lock.

*

, press the

Display on the revolution counter

When the system is armed, all LEDs pulse. After
approx. 16 minutes one LED flashes.

NAVIGATIONREFERENCE

The principle

The alarm system, when activated, reacts if:

> A door, the engine compartment lid or the

tailgate is opened

> There is movement inside the car

> The car's inclination changes, for instance if

an attempt is m ade to jack it up and steal the
wheels or to raise it prior to towing away

> There is an interruption in the power supply

from the battery

The alarm system briefly indicates unauthorized
entry or tampering by means of:

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

> LEDs pulse or LED flashes: system is armed.

> One LED flashes at short intervals:

A door, the bonnet or the tailgate is not
properly closed. Even if these are not closed

31

fully, the remaining items are deadlocked

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

and the LEDs pulse after approx. 10 seconds
for approx. 16 minutes. Afterwards, one LED
flashes.
The interior movement detector is not acti­vated.

> LEDs go out after the vehicle is unlocked:

No attempt was made to tamper with the
car.

> LEDs flash after unlocking until the key is

inserted in the ignition, but for no longer
than approx. 5 minutes: an attempt was
made to tamper with the car.

Tilt alarm sensor

The vehicle's inclination is monitored. The alarm
is triggered, for instance, if an attempt is made
to steal the car's wheels or tow it away.

Opening and closing

Interior movement detector

Before the interior movement detector can
operate correctly, the windows and glass roof
must be closed.

Avoiding false alarms

The tilt alarm sensor and the interior movement
detector can be switched off together.

This prevents false alarms, e.g. in the following
situations:

> In duplex garages

> When being transported on car-carrying

trains, ferries or trailers

> If pets are to remain inside the car

Switching off the tilt alarm sensor and
interior movement detector

> Press the button on the remote con-

trol twice in succession.

> Lock the vehicle twice with the integrated

key.

LEDs flash in short succession for approx. 2 sec­onds.
The tilt alarm sensor and the interior movement
detector are switched off until the car is next
unlocked and locked.

Convenient access*

Convenient access enables you to enter your
vehicle without having to hold the remote con­trol in your hand. All you need to do is wear the
remote control close to your body, e.g. in your
jacket pocket. The vehicle automatically detects
the remote control within the immediate vicinity
or in the passenger compartment.

Convenient access supports the following func­tions:

> Unlocking/locking the vehicle

> Unlocking the tailgate by itself

> Enginestarting

> Convenient operation

Functional requirements

> The vehicle or the tailgate can only be

locked when the vehicle detects that the
remote control currently in use is outside of
the vehicle.

> The vehicle cannot be locked or unlocked

again until after approx. 2 seconds.

> The engine can only be started when the

vehicle detects that the remote control is
inside the vehicle.

> The doors and tailgate must be closed to be

able to operate the windows and glass sun­roof.

Comparison to standard remote controls

In general, there is no difference between using
convenient access or pressing the buttons on
the remote control to carry out the functions
mentioned above.
Instructions on opening and closing are found
starting on page 26.

Special features regarding the use of convenient
access are described below.

If you notice a brief delay while opening or

closing the windows or glass sunroof, the
system is checking whether a remote control is
inside the vehicle. Repeat the opening or closing
procedure, if necessary.<

32

Unlocking

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Press button 1.

Convenient opening with the remote control,
refer to page 28.

Locking

Press button 1.

For convenient closing, press and hold button 1.
The power windows and the glass sunroof
closed.

*

are

Unlocking the tailgate separately

Press the button on the outside of the tailgate.

If the vehicle detects that a remote control

has been accidentally left inside the
locked vehicle's cargo bay after the tailgate is
closed, the tailgate will reopen slightly. The haz­ard warning flashers flash and an acoustic sig-

*

sounds.<

nal

Windows and glass sunroof, electric*

If the engine is switched off, you can still operate
the windows and glass sunroof so long as a door
or the tailgate has not been opened.

If the doors and tailgate are closed again and the
remote control is located inside the vehicle, the
windows and the glass sunroof can be operated
again.

Insert the remote control into the ignition lock to
be able to operate the windows or glass sunroof
when the engine is switched off and the doors
are open.

Switching on radio readiness

Switch on radio readiness by briefly pressing the
start/stop button, page 44.

Do not depress the brake or the clutch,
otherwise the engine will start.<

Starting the engine

The engine can be started or the ignition can be
switched on when a remote control is inside the
vehicle. It is not necessary to insert a remote
control into the ignition lock, page 44.

Switching off the engine in cars with
automatic transmission

The engine can only be switched off when the
selector lever is in position P, page 45.
To switch the engine off when the selector lever
is in position N, the remote control must be in
the ignition lock.

Before driving a vehicle with automatic
transmission into a car wash

1. Insert remote control into ignition lock.

2. Depress the brake.

3. Move the selector lever to position N.

4. Switch off the engine.

The vehicle can roll.

Malfunction

Convenient access may malfunction due to local
radio waves.

If this happens, open or close the vehicle via the
buttons on the remote control or using the inte­grated key.
Insert the remote control into the ignition lock
and start the engine.

Warning lamps

The warning lamp comes on when an
attempt is made to start the engine: the

engine cannot be started. The remote
control is not inside the vehicle or is malfunc­tioning. Take the remote control with you inside
the vehicle or have it checked. If necessary,
insert another remote control into the ignition
lock.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

33

The warning lamp comes on when the

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

engine is running: the remote control is

no longer inside the vehicle. After the
engine is switched off, the engine can only be
restarted within approx. 10 seconds.

The indicator lamp comes on and a mes-

sage appears on the Control Display:

replace the battery in the remote con­trol.

Replacing the battery

The remote control for convenient access con­tains a battery that will need to be replaced from
time to time.

1. Remove the cover.

Opening and closing

2. Insert the new battery with the plus side fac-

ing up.

3. Press the cover on to close.

Take the old battery to a battery collection
point or to your MINI Dealer.<

Glass sunroof, electric*

To prevent injuries, exercise care when

closing the glass sunroof and keep it in
your field of vision until it is shut.
Take the key with you when you leave the car,
otherwise children could operate the sunroof
and possibly injure themselves.<

Raising

> Press the switch backward to the resistance

point and hold it there.
Both glass sunroofs are raised.
Releasing the switch stops the movement.

> With the ignition switched on, press the

switch backward beyond the resistance
point.
Both closed sunroofs are raised fully.
Pressing again stops the movement.

Opening, closing

With the ignition switched on and the glass sun­roof raised, press the switch backward and hold
it there.
The front glass sunroof opens.
The rear glass sunroof is closed.
Releasing the switch stops the movement.

The glass sunroof can be closed in the same way
by pressing the switch forward.

The front glass sunroof remains in a raised posi­tion. The rear glass sunroof is raised. Pressing on
the switch again closes both sunroofs completely.

Convenient operation via door lock or conve­nient access, refer to page 28, 29, 33.

Roller sun blind

The roller sun blind can be opened and closed
independently of the glass sunroof.

Following interruptions in electrical
power supply

After a power failure, there is a possibility that
the glass sunroof can only be raised. In this case,
have the system initialized. The manufacturer of
your MINI recommends that you have this work
done by your MINI Dealer.

34

Windows

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

To prevent injuries, exercise care when

closing the windows and keep them in
your field of vision until they are shut.
Take the remote control with you when you
leave the car, otherwise children could operate
the electric windows and possibly injure them­selves.<

If, after a window is opened and closed

several times in close succession, the win­dow can only be closed and not opened, the sys­tem is overheated. Let the system cool for sev­eral minutes with the ignition switched on or the
engine running.<

Opening, closing

> Press the switch downwards.

The window opens until you release the
switch.

> Tap the switch downwards.

The window opens automatically if the igni­tion is switched on. Tap the switch again to
stop the opening movement.

The window can be closed in the same way by
pressing the switch up.

Pinch protection system

If the closing force exceeds a specific value as a
window closes, the closing action is interrupted
and the window reopens slightly.

Even though there is the pinch protection

system, always ensure that the window's
travel path is clear, otherwise the safety system
might fail to detect certain kinds of obstructions,
such as thin objects, and the window would con­tinue closing.

Do not install any accessories that might inter­fere with window movement. Otherwise the
pinch protection system could be impaired.<

Closing without pinch protection

If there is an external danger, or if ice on the win­dows, etc., prevents you from closing the win­dows normally, the window can be closed man­ually.

1. Press the switch upward and hold it there.

Pinch protection is limited and the window
reopens slightly if the closing force exceeds
a certain value.

2. Press the switch upward again within

approx. 4 seconds and hold it there. The
window closes without pinch protection.

NAVIGATIONREFERENCE

After switching off the ignition

When the ignition is switched off, the windows
can still be operated for approx. 1 minute as
long as no door is opened.

Take the key with you when you leave the
car, otherwise children could operate the

electric windows and possibly injure them­selves.<

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

35

Adjustments

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Sitting safely

The ideal sitting position can make a vital contri­bution to relaxed, fatigue-free driving. In con­junction with the safety belts, the head restraints
and the airbags, the seated position has a major
influence on your safety in the event of an acci­dent. To ensure that the safety systems operate

Adjustments

with optimal efficiency, we strongly urge you to
observe the instructions contained in the follow­ing section.

For additional information on transporting chil­dren safely, refer to page 42.

Airbags

Always maintain an adequate distance

between yourself and the airbags. Always
grip the steering wheel on the rim, with your
hands in the 3 o'clock and 9 o'clock positions, to
minimize the risk of injury to the hands or arms
in the event of the airbag being triggered off.
No one and nothing is to come between the air­bags and the seat occupant.
Do not use the cover of the front airbag on the
front passenger side as a storage area. Ensure
that the front passenger is correctly seated, e.g.
that no feet or legs are propped against the
dashboard. Otherwise, leg injury could result if
the front airbag suddenly deployed.
Make sure that passengers do not lean their
heads against the side airbags, otherwise seri­ous injuries could result if the airbags suddenly
deployed.<

Even if you follow all the instructions, injuries
resulting from contact with airbags cannot be
fully excluded, depending on the circumstances.
The ignition and inflation noise may provoke a
mild hearing loss in extremely sensitive individ­uals. This effect is usually only temporary.

For airbag locations and additional information
on airbags, refer to page 78.

Head restraint

A correctly adjusted head restraint reduces the
risk of neck injury in the event of an accident.

Adjust the head restraint in such a way
that its center is at approx. ear level. Oth-

erwise, there is an increased risk of injury in the
event of an accident.<

Head restraints, refer to page 38.

Safety belt

Before every drive, make sure that all occupants
wear their safety belts. Airbags complement the
safety belt as an additional safety device, but
they do not represent a substitute.

Never allow more than one person to

wear a single safety belt. Never allow
infants or small children to ride in a passenger's
lap.
Make sure that the belt in the lap area sits low
across the hips and does not press against the
abdomen. The safety belt must not rest against
the throat, run across sharp edges, pass over
hard or fragile objects or be pinched. Fasten the
safety belt so that it is pulled taut across the lap
and shoulder, fitting the body snugly without
any twists. Otherwise the belt could slide over
the hips in the event of a frontal collision and
injure the abdomen. Avoid wearing bulky cloth­ing and regularly pull the belt in the upper-body
area taut, otherwise its restraining effect could
be impaired.<

Safety belts, refer to page 39.

Seats

Note before adjusting

Never attempt to adjust your seat while

the vehicle is moving. The seat could
respond with unexpected movement, and the
ensuing loss of vehicle control could lead to an
accident.

36

On the front passenger seat as well, do not

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

incline the backrest too far to the rear while the
vehicle is being driven, otherwise there is a dan­ger in the event of an accident of sliding under
the safety belt, eliminating the protection nor­mally provided by the belt.<

Comply with the instructions on head restraint
height on page 38 and on damaged safety belts
on page 39.

Backrest

Seat adjustment

Observe the instructions on page 36 to
ensure the best possible personal protec-

tion.<

Longitudinal adjustment

Pull the lever, arrow 1, and slide the seat to the
desired position, arrows 2.
After releasing the lever, move the seat gently for­ward or back to make sure it engages properly.

Height

Pull the lever, arrow 1, and apply your weight to
the backrest or lift it off, as necessary, arrows 2.

Lumbar support*

You can also adjust the contour of the backrest
to obtain additional support in the lumbar
region.

The upper hips and spinal column receive sup­plementary support to help you maintain a
relaxed, upright sitting position.

Turn the wheel to increase or decrease the cur­vature.

Entry to the rear

Convenient entry

The convenient entry feature includes a
mechanical memory function for the longitudi­nal adjustment and backrest angle.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

Pull up or push down the lever repeatedly,
arrows 1, until the desired height is reached,
arrows 2.

37

1. Pull up the lever on the seat backrest,

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Adjustments

arrow 1.

The backrest folds forward.

2. Move the seat forward by pushing on the

backrest, arrow 2.

Previous position

1. Push the seat back into its previous position.

Do not fold the backrest up until the

seat is in its previous position. Other­wise, the seat will engage in its current posi­tion. In this case, adjust the longitudinal po­sition manually, page 37.<

2. Fold the backrest back up to lock the seat.

When moving the seat backwards, ensure

that you do not cause personal injury or
property damage.
Before driving off, engage the front seats and
seat backrests. Otherwise there is a risk of acci­dent due to unexpected movement.<

Head restraints

A correctly adjusted head restraint reduces the
risk of neck injury in the event of an accident.

Adjust the head restraint in such a way

that its center is at approx. ear level. Oth­erwise, there is an increased risk of injury in the
event of an accident. Only remove a head
restraint if no one will be sitting on the seat in
question. Reinstall the head restraint before
transporting anyone on that seat. Otherwise,
the passenger will be without protection from
the head restraint.<

Height adjustment

To raise: pull up.

To lower: press the button, arrow 1, and slide
the head restraint down.

Removing

Front

1. Pull up as far as it will go.

2. Fold the backrest forward slightly.

3. Press button 1 and pull the head restraint

out as far as it will go.

4. Additionally press button 2 and pull the

head restraint out completely.

5. Fold back the backrest.

Rear

1. Pull up as far as it will go.

2. Press button 1 and pull the head restraint

out completely.

38

Seat heating*

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Switching on

Press once for each temperature level.
Three LEDs indicate the highest temperature.

If you continue driving within the next 15 min­utes, the seat heating is automatically activated
at the previously set temperature.

The temperature is lowered or the heating is
switched off entirely to save on battery power.
The LEDs stay lit.

Switching off

Press button longer.

Safety belts

Observe the instructions on page 36 to
ensure the best possible personal protec-

tion.<

Before every drive, make sure that all occupants
wear their safety belts. Airbags complement the
safety belt as an additional safety device, but
they do not represent a substitute.

Front and rear seats

Closing

Make sure you hear the lock engage in the belt
buckle.

The upper belt anchor is suitable for adults of
any stature as long as the seat is adjusted prop­erly, page 36.

Opening

1. Grasp the belt firmly.

2. Press the red button in the buckle.

3. Guide the belt into its reel.

Seat belt reminder

Front seats

The indicator lamps come on and an
acoustic signal sounds.In addition, a
message appears on the Control Dis-

play. Check whether the safety belt has
been fastened correctly. The 'Fasten safety
belts' reminder is issued when the driver's safety
belt has not been fastened. The 'Fasten safety
belts' reminder is also activated at road speeds
above approx. 5 mph or 8 km/h if the front pas­senger's safety belt has not been fastened, if
objects are placed on the front passenger seat,
or if driver or front passenger unfasten their
safety belts.

Damage to safety belts

If the safety belts are damaged or stressed

in an accident: have the safety belt system
and its seat-belt tensioners replaced and the
belt anchors checked. Have th is work carried out
only by a MINI Dealer or by a workshop that has
specially trained personnel working in accor­dance with the specifications of the MINI manu­facturer, otherwise correct operation of these
safety systems is not ensured.<

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

39

Mirrors

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Exterior mirrors

The front passenger's mirror is more con-

vex than the driver's mirror. The objects
seen in the mirror are closer than they appear.
Do not gauge your distance from traffic behind
you on the basis of what you see in the mirror;
otherwise there is an increased risk of an acci­dent.<

Adjustments

1 Adjusting the left or right exterior mirror

2 Folding mirrors in and out

Manual adjustment

The mirrors can also be adjusted manually: press
the edge of the glass.

Folding mirrors in and out*

Turn the knob beyond the pressure point in
direction 2. The mirrors can be folded in at road
speeds up to approx. 20 mph/30 km/h.

This can be beneficial in narrow streets, for
example, or for moving mirrors that were folded
in by hand back out into their correct positions.

Automatic heating*

At outside temperatures below a certain limit,
both exterior mirrors are automatically heated
while the engine is running or the ignition
switched on.

*

Interior rearview mirror

To reduce glare from vehicles behind you when
you are driving at night:

Turn the knob.

Interior mirror, automatic dimming*

The automatic dimming feature of the interior
rearview mirror* is controlled by two photo cells
in the mirror. One photo cell is in the mirror
frame, arrow; the other is on the back of the mir­ror.

In order to ensure that the system functions cor­rectly, keep the photo cells clean, do not cover
the area between the interior rearview mirror
and windshield, and do not affix adhesive labels
or stickers of any kind to the windshield directly
in front of the mirror.

40

Steering wheel

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Adjustments

Do not adjust the steering wheel position
while the car is in motion, otherwise there

is a risk of accident due to an unexpected move­ment.<

1. Fold the lever down.

2. Move the steering wheel to the preferred

distance and angle to suit your seated posi­tion.

3. Swing the lever back up.

Do not use force to swing the lever
back up, otherwise the mechanism

will be damaged.<

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

41

Transporting children safely

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The right place for children

Do not leave children unattended in the
vehicle, otherwise they could endanger

themselves and/or other persons by opening the
doors, for example.<

Children should always sit in the rear

Accident research has shown that the safest
place for children is on the rear seat.

Only transport children under the age of

13 or smaller than 5 ft/150 cm in the rear
in a child-restraint system suitable for their age,
weight and size. Otherwise there is an increased
risk of injury in the event of an accident.<

Children 13 years of age or older must be buck­led in with a safety belt as soon as there no
longer is any child-restraint system that is
appropriate for their age, size and weight.

Only install child seats in the rear when

Transporting children safely

the rear seat backrest is folded all the way
back and engaged. Otherwise there will be
an increased risk of injury in the event of an
accident.<

Exception for front passenger seat

Front passenger airbags

Should it be necessary to use a child-

restraint system on the front passenger
seat, the front and side airbags must be deacti­vated. Otherwise, there is an increased risk of
injury to the child if the airbags deploy, even if
the child is seated in a child-restraint system.<

For more information on automatic deactivation
of the front passenger airbags, refer to page 78.

Child-restraint systems, installation

Observe the child-restraint system manu­facturer's instructions when selecting,

installing and using child-restraint systems. Oth­erwise the protective effect may be diminished.<

On the front passenger seat

After installing a child-restraint system on

the front passenger seat, make sure that
the front and side airbags for the front passen­ger are deactivated, otherwise there is an
increased risk of injury if the airbags deploy.<

Child seat security

All rear safety belts and the safety belt for the
front passenger can be prevented from being
pulled out in order to secure child-restraint sys­tems.

To lock the safety belt

1. Secure the child-restraint system with the

belt.

2. Pull the belt strap all the way out.

3. Allow the belt strap to retract and pull it taut

against the child-restraint system.

The safety belt is locked.

42

To unlock the safety belt

1. Open the belt buckle

2. Remove the child-restraint system.

3. Allow the safety belt strap to retract all the way.

LATCH child-restraint

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

fixing system

LATCH: Lower Anchors and Tethers for CHildren.

To install and use the LATCH child-

restraint system, follow the operating and
safety instructions provided by the manufac­turer of the system, otherwise the protective
function of the seat may be compromised.<

Placement of the tether strap

Anchor points for LATCH anchors

Before installing the child's seat, pull the belt out
of the area for the child-restraint fixing system.

The anchor points for the lower LATCH anchors
are located behind the labeled protective caps.

Make sure that the two LATCH anchors are

properly engaged and that the child­restraint system rests firmly against the seat
backrest, otherwise the protective function of
the seat may be compromised.<

Child-restraint system with tether strap

Use the tether strap anchors to secure

child-restraint systems only, otherwise the
anchors could be damaged.<

1 Direction of travel

2 Head restraint

3 Tether strap hook

4 Cargo bay floor

5 Anchor

6 Seat backrest

7 Tether strap of the child-restraint system

Make sure the upper retaining strap does

not run over sharp edges and is not
twisted as it passes to the top anchor. Otherwise
the strap will not properly secure the child­restraint system in the event of an accident.<

1. Push the head restraint upward.

2. Guide the tether strap between the head

restraint holders.

3. Attach the tether strap to the anchor using

the hook.

4. Push the head restraint into its lowermost

position.

5. Pull the retaining strap tight.

NAVIGATIONREFERENCE

There are two additional anchors for child­restraint systems with tether straps, arrows.

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

43

Driving

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Ignition lock

Inserting the key into the ignition lock

Driving

Insert the key all the way into the ignition lock.

Radio readiness
Individual electrical consumers can operate.

Removing the key from the ignition lock

Press in the key briefly. It is ejected slightly.

At the same time:

> The ignition is switched off if it was on

beforehand.

Automatic transmission

You cannot take out the key unless the selector
lever is in the P position: interlock.

Start/stop button

Press the start/stop button to switch radio readi­ness or the ignition on and off. Do not depress
the brake or clutch while doing so.

When you press the start/stop button and
depress the clutch if the car has manual

transmission or the brake if the car has auto­matic transmission, the engine starts.<

Radio readiness

Individual electrical consumers can operate. The
time and outside temperature are displayed in
the tachometer.

Radio readiness is switched off automatically:

> When the key is removed from the ignition

lock

> When using convenient access

the button on the door handle or the
button on the remote control, refer to Lock­ing on page 33

*

by pushing

44

Ignition on

Most indicator and warning lamps in indicator
area 1, page 13, light up for varying lengths of
time.

When the engine is off, switch off the igni­tion and any unnecessary electrical con-

sumers in order to preserve the battery.<

Radio readiness and ignition off

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

All indicator and warning lamps in the displays
go out.

The ignition automatically turns off
driver's door is opened. Pressing the start/stop
button again switches the ignition back on.

The ignition is not switched off in situations such
as the following:

> The clutch or brake is depressed

> The low beams are switched on

*

when the

Starting the engine

Do not allow the engine to run in enclosed

spaces; otherwise inhalation of the nox­ious exhaust gases can lead to unconsciousness
and death. Exhaust gases contain carbon mon­oxide, an odorless and colorless, but highly toxic
gas. Never leave an unattended vehicle with the
engine running, otherwise such a vehicle repre­sents a potential safety hazard.
Before leaving the car while the engine is run­ning, place the transmission in neutral or move
the selector lever to position P and forcefully
apply the parking brake to prevent the car from
moving.<

Avoid frequent starting in quick succes-

sion or repeated start attempts in which
the engine does not start. Otherwise, the fuel is
not burned or inadequately burned and there is
a danger of overheating and damaging the cat­alytic converter.<

Do not let the engine warm up with the vehicle
at a standstill. Move off immediately at a moder­ate engine speed.

When starting the engine, do not depress the
accelerator pedal.

Manual transmission

Key in ignition lock or inside vehicle with conve­nient access, refer to page 32.

1. Depress the brake.

2. Depress the clutch.

3. Press the start/stop button.

Automatic transmission

Key in ignition lock or inside vehicle with conve­nient access, refer to page 32.

1. Depress the brake.

2. Move the selector lever to position P.

3. Press the start/stop button.

The starter operates automatically for a certain
time, and stops automatically as soon as the
engine has started.

switching off the Engine

Always take the key with you when you
leave the vehicle.

When parking, apply the parking brake force­fully, otherwise the vehicle could begin to roll.<

Manual transmission

1. With the car at a standstill, press the start/

stop button.

2. Shift into first gear or reverse.

3. Forcefully apply the parking brake.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

Automatic transmission

1. With the car at a standstill, move the selector

lever to position P.

2. Press the start/stop button.

3. Forcefully apply the parking brake.

45

Parking brake

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The parking brake is primarily intended to pre­vent the vehicle from rolling while parked; it
brakes the rear wheels.

Applying

Driving

The lever locks in position automatically.

Releasing

Pull slightly upwards, press the button and lower
the lever.

In exceptional cases, if the parking brake

has to be used to slow or stop the car, do
not pull the lever up too hard. In doing so, con­tinuously press the button of the parking brake
lever.
Otherwise, excessive force could lead to over­braking and loss of traction, i.e. fishtailing, at the
rear axle.<

Reverse gear

Select this only when the vehicle is stationary.
When the gearshift lever is pressed to the left, a
slight resistance has to be overcome.

Automatic transmission* with Steptronic

In addition to the fully automatic mode, you can
shift gears manually using Steptronic, page 47.

Parking the vehicle

To prevent the vehicle from rolling, always
select position P and apply the parking

brake before leaving the vehicle with the engine
running.<

Removing the key

1. Move the selector lever to position P.

2. Switch off the engine.

3. Remove the key.

Selector lever positions

P R N D M/S + –

Displays in the tachometer

Manual transmission

When shifting into 5th or 6th gear, press

the gearshift lever to the right. Otherwise
the engine could be damaged if you inadvert­ently shift into 3rd or 4th gear.<

46

P R N D DS M1 to M6

The selector lever position is displayed, or the
current gear in the manual mode.

Changing selector lever positions

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

> The selector lever can only be moved out of

position P if the ignition is switched on or the
engine is running: interlock.

> Before moving the lever away from P or N

with the vehicle stationary, first depress the
brake; otherwise the selector lever will
refuse to move: shiftlock.

To prevent the vehicle from creeping

after you select a driving position, de­press the brake until you are ready to start.<

A lock prevents accidental shifting into selector
lever positions R and P.

Overriding the selector lever lock

Press the button on the front of the selector
lever, arrow.

P Park

Select this only when the vehicle is stationary.
The transmission locks to prevent the drive
wheels from turning.

R Reverse

Select this only when the vehicle is stationary.

N Neutral

Select this when you are in a car wash, for exam­ple. The vehicle can roll.

D Drive, automatic position

Position for normal vehicle operation. All for­ward gears are selected automatically.

Under normal operation conditions, fuel con­sumption is lowest when you drive in position D.

Kick-down

Kick-down enables you to achieve maximum
performance.
Depress the accelerator pedal beyond the full­throttle resistance point.

Sport program and manual operation
M/S

Move the selector lever from position D to the
left into the M/S shifting slot:
The Sport program is activated and DS is dis­played.

Shifting with the selector lever

Push the selector lever forward or pull it back to
activate manual operation. Steptronic shifts the
gear.

> Pull the selector lever in the + direction.

Transmission shifts up.

> Push the selector lever in the – direction.

Transmission shifts down.

The tachometer displays M1 to M6.

To use the automatic mode again, move the
selector lever to the right into position D.

Upshifts and downshifts are executed only when
they will result in a plausible combination of
engine and vehicle speed; thus, for example, a
downshift that would cause the engine to over­rev will not be executed by the system. The
selected gear is displayed briefly, followed by
the actual gear.

Shifting on the steering wheel

With the selector lever in position D, automatic
drive, you can shift gears using the shift paddles
on the steering wheel. The transmission auto­matically switches to manual mode.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

47

If you do not shift gears with the shift paddles or

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

accelerate for a certain amount of time, the
transmission automatically returns to D, auto­matic drive.

Driving

Turn signals/ headlamp flasher

> Pull one of the shift paddles.

Transmission shifts up.

> Push one of the shift paddles.

Transmission shifts down.

M1 to M6 is displayed in the gear indicator.

Overriding the selector lever lock

Should the selector lever refuse to move out of
position P although the button on the selector
lever is pressed, the selector lever lock can be
overridden:

1. Unclip the sleeve of the selector lever.

2. Pull the sleeve up over the selector lever

until the sleeve is inside out. Disconnect the
cable connector if necessary.

3. Take the hub cover remover 1 out of the

onboard tool kit and insert it in the loop on
the front passenger side.

4. Pull the loop up.

5. Move the selector lever into the desired

position by pressing the button on the front
of the selector lever.

1 Turn signal indicator

2 Headlamp flasher

Using turn signals

Press the lever beyond the resistance point.

To turn off manually, press the lever to the resis­tance point.

Unusually rapid flashing of the indicator
lamp indicates that an indicator bulb has

failed.<

Indicating a turn briefly

Press the lever as far as the resistance point for
as long as you wish to indicate a turn.

Triple turn signal activation

Press the lever as far as the resistance point.

You can set whether the turn signal is to flash
once or three times.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Vehicle and tires".

48

5. Select "Lighting".

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

6. Select "Triple turn signal".

Triple turn signaling is activated.

Wiper system

Intermittent wipe or rain sensor*

If the car is not equipped with a rain sensor, the
intermittent-wipe time is preset.

If the car is equipped with a rain sensor, the time
between wipes is controlled automatically and
depends on the intensity of the rainfall. The rain
sensor is mounted on the windshield, directly in
front of the interior rearview mirror.

Activating intermittent wipe or rain
sensor

Press button, arrow 3.

Deactivate the rain sensor before entering
an automatic car wash. Failure to do so

could result in damage caused by undesired
wiper activation.<

Adjusting the sensitivity of the rain
sensor

1. Switch on the ignition, refer to page 44.

2. Briefly press the button in the turn indicator

lever repeatedly until "SET/INFO" is dis­played.

1 Switching on wipers

2 Switching off wipers or brief wipe

3 Activating/deactivating intermittent mode

or rain sensor

4 Cleaning windshield and headlamps

*

*

Switching on wipers

Press the lever upward, arrow 1.

The lever automatically returns to its initial posi­tion when released.

Normal wiper speed

Press once.
The system switches to intermittent operation
when the vehicle is stationary.

Fast wiper speed

Press twice or press beyond the resistance point.
The system switches to normal speed when the
vehicle is stationary.

NAVIGATIONREFERENCE

3. Press and hold the button until the display

changes.

4. Briefly press the button repeatedly until the

symbol and "SET" are displayed.

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

49

5. Press and hold the button until the display

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

changes.

Driving

6. Press the button to select the desired sensi-

tivity.

7. Wait, or press and hold the button until the

display changes.
The settings are stored.

Deactivating intermittent wipe or rain
sensor

Press the button again, arrow 3.

Brief wipe

Press the lever downward once, arrow 2.

Cleaning windshield and headlamps*

Pull the lever, arrow 4.

Washer fluid is sprayed onto the windshield and
the wipers are operated briefly.

When the vehicle lighting system is switched on,
the headlamps are cleaned at regular and
appropriate intervals.

In cars equipped with an alarm system, the
headlamps cannot be cleaned when the bonnet
is open.

Do not use the washers when the washer

fluid reservoir is empty, otherwise you will
damage the washer pump.
Only use the washers if the bonnet has been
completely closed, otherwise the headlamp
washer system
the washers if there is any danger that the fluid
will freeze on the windshield. If you do, your
vision could be obscured. For this reason, use
antifreeze.<

*

may be damaged. Do not use

Window washer nozzles

The window washer nozzles are heated auto-

*

matically
ignition is switched on.

while the engine is running or the

Rear window wiper

0 Rear wipers parked

1 To switch on intermittent wipe :

Turn the cap to level 1.
Operation is continuous in reverse gear.

Cleaning the rear window

2 To clean the rear window during intermit-

tent wipe :
Turn the cap further to level 2 and hold it
there.

3 To clean the rear window when wipers are

parked :
Turn the cap to level 3 and hold it there.

Do not use the washers when the washer
fluid reservoir is empty, otherwise you will

damage the washer pump.<

Washer fluid

Washer fluid antifreeze is flammable.

Therefore, keep it away from ignition
sources, store it only in the closed original con­tainer and keep it out of reach of children, oth­erwise there is a risk of personal injury. Comply
with the instructions on the container.<

50

Washer fluid reservoir

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Only refill washer fluid that contains anti-

freeze when the engine is cool, to avoid
contact with hot engine parts. Otherwise, fluid
spills constitute a fire hazard and a risk to per­sonal safety.<

Fill with water and, if required, with a washer
antifreeze, according to manufacturer's recom­mendations.

Mix the water and antifreeze before filling

the washer fluid reservoir to make sure
the correct concentration is maintained.<

Capacity

Approx. 2.6 US quarts/2.5 liters.

With headlamp washer system:
Approx. 4.8 US quarts/4.5 liters.

Cruise control*

The concept

Cruise control is available at vehicle speeds of at
least approx. 20 mph or 30 km/h. The car then
stores and maintains the speed that you specify
using the button on the steering wheel.

Do not use cruise control when driving at

constant speed is prevented by adverse
conditions, e.g. winding roads, dense traffic or
poor road conditions due to, e.g., snow, rain, ice
or loose surfaces. Otherwise you could lose con­trol of the vehicle and cause an accident as a
result.<

Activating

1 Resuming cruise control

2 Activating/deactivating cruise control

3 Maintaining, storing and increasing speed

4 Maintaining, storing and decreasing speed

Indicator lamp in the speedometer lights up. The
cruise control system is ready and can be acti­vated.

Activating/deactivating cruise control

Press button 2.

In addition, the system is automatically deacti­vated:

> When the brakes are applied

> When the clutch is depressed

> When the automatic transmission is in selec-

tion lever position N

> When the driving stability control system is

active

Cruise control is not deactivated by depressing
the accelerator pedal. Once the accelerator
pedal is released, the stored speed is achieved
again and maintained.

The stored speed is cleared when the ignition is
switched off.

Maintaining current speed

Press button 3.

The system maintains and stores the current
vehicle speed.

If, on a downhill grade, the engine braking effect
is not sufficient, the controlled speed may be
exceeded. On uphill grades vehicle speed may
drop if the engine output is insufficient.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

51

Increasing speed

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Press button 3 repeatedly until the desired
speed is reached. Every time you press the but­ton, the speed increases by approx. 1 mph or
2km/h.

Driving

Accelerating using the button

Press and hold button 3.

The vehicle accelerates without pressure on the
accelerator pedal. After the button is released,
the driving speed is maintained and stored.

Decreasing speed

Press button 4 repeatedly until the desired
speed is reached.

The functions here are the same as for increas­ing the speed or accelerating, except that the
speed will be decreased.

Resuming a speed stored beforehand

Press button 1.

The last speed stored is achieved again and
maintained.

The stored speed is cleared when the ignition is
switched off.

Display in tachometer*

Selected speed is displayed briefly.

If --- mph or --- km/h is displayed briefly
in the tachometer, the conditions neces-

sary for operation may not be fulfilled.<

Malfunction

The warning lamp in the tachometer
lights up if the system fails. A message
appears on the Control Display.

52

Everything under control

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Odometer, outside temperature display, clock

1 Outside temperature display and clock or

current speed

2 Odometer and trip odometer

3 Resetting the trip odometer

Units of measure

Select the respective units of measure, miles or
km for the odometer as well as 7 or 6 for the
outside temperature, page 58.

Outside temperature display, time

Setting the time, refer to page 61.

Current vehicle speed

To have the current speed shown in the upper
display otherwise serving for the outside tem­perature display and clock.

1. Press the button in the turn indicator lever

repeatedly until the current speed appears
in the lower display.

2. Wait for the speed display to automatically

move to the upper display.

The outside temperature then appears in the
lower display.

Odometer and trip odometer

Resetting the trip odometer

With the ignition switched on, press knob 3 in
the tachometer.

When the vehicle is parked

To display the time, outside temperature and
odometer briefly after the key is removed from
the ignition lock:
Press knob 3 in the tachometer.

Tachometer

NAVIGATIONREFERENCE

Outside temperature warning

When the displayed temperature sinks to
approx. +377/+36, a signal sounds and a
warning lamp lights up. There is an increased
risk of black ice.

Black ice can also form at temperatures
above +37 7/+36. You should therefore

drive carefully on bridges and shaded roads, for
example, otherwise there is an increased risk of
an accident.<

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

Never operate the engine with the needle in the
red overspeed zone of the gauge. In this range,
the fuel supply is interrupted to protect the
engine.

53

Coolant temperature

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Computer*

A warning lamp will come on if the coolant, and
therefore the engine, becomes too hot. In addi­tion, a message will appear on the Control Display.

Check coolant level, refer to page 166.

Fuel gauge

Fuel tank capacity

You can find information on refueling on
page 152.

If the tilt of the vehicle varies for a longer period,

Everything under control

when you are driving in mountainous areas, for
example, the indicator may fluctuate slightly.

MINI Cooper, MINI Cooper S

Approx. 13.2 US gallons/50 liters.

Reserve

Once the fuel level has fallen to the reserve zone
of approx. 2.1 US gallons/8 liters the remaining
indicator lamps change from orange to red,
arrow, and a message is displayed briefly on the
Control Display. The tachometer
remaining cruising range. When the range is less
than approx. 30 miles/50 km, the message
remains in the Control Display.

If the range displayed is less than
30 miles/50 km, be sure to refuel; other-

wise engine functions are not guaranteed and
damage could occur.<

displays the

Displays in tachometer

Press the button in the turn indicator lever
repeatedly to call up various items of informa­tion.

The following items of information are displayed
in the order listed:

> Cruising range

> Average fuel consumption

> Current fuel consumption

> Average speed

> Current vehicle speed

To set the corresponding units of measure, refer
to Units of measure on page 58.

Cruising range

Displays the estimated cruising range available
with the remaining fuel. The range is calculated
on the basis of the way the car has been driven
over the last 18 miles/30 km and the amount of
fuel currently in the tank.

If the range displayed is less than
30 miles/50 km, be sure to refuel; other-

wise engine functions are not guaranteed and
damage could occur.<

Average fuel consumption

Calculated for the time the engine has been run­ning.

With the trip computer, page 56, you can have the
average consumption for another trip displayed.

To reset average fuel consumption: press the
button in the turn indicator lever for approx.
2seconds.

54

Current fuel consumption

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Displays the current fuel consumption to allow
you to see whether your current driving style is
conducive to fuel economy with minimum
exhaust emissions.

Average speed

Periods with the vehicle parked and the engine
switched off are not included in the calculations
of average speed.

With the trip computer, page 56, you can have
the average speed for another trip displayed.

To reset average speed: press the button in the
turn indicator lever for approx. 2 seconds.

Current vehicle speed

To have the current speed shown in the upper
display otherwise serving for the outside tem­perature display and clock.

1. Press the button in the turn indicator lever

repeatedly until the current speed appears
in the lower display.

2. Wait for the speed display to automatically

move to the upper display.

The outside temperature then appears in the
lower display of the computer.

Displays on the Control Display

To open the computer via the onboard monitor,
basic operation on page 16.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Naviga-

tion" and press the MINI joystick.

3. If necessary, move the highlight marker to

the uppermost field. Select "Car Data".

4. Select "Onboard info".

> Estimated time of arrival at destination:

> Manually enter a distance in the com-

puter, refer to information further below

> Enter a destination in the navigation sys-

tem, page 104

> Cruising range

> Distance to destination:

> Manually enter a distance in the com-

puter, refer to information further below

> Enter a destination in the navigation sys-

tem, page 104

> Average speed

> Average fuel consumption

NAVIGATIONREFERENCE

Resetting values

To reset the values for the average speed and
average fuel consumption:

1. Select the respective menu entry.

2. Press the MINI joystick to confirm the mes-

sage.

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

55

Entering a distance manually

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

1. Select "Dist. to dest.".

2. Turn the MINI joystick to select the distance

to your destination.

3. Press the MINI joystick to apply the setting.

The distance is mandated automatically during
destination guidance.

Trip computer

The trip computer is suitable e.g. for a holiday
trip.

1. Press the button.

Everything under control

This opens the start menu.

2. Move the MINI joystick to highlight "Naviga-

tion" and press the MINI joystick.

3. Select "Car Data".

4. Select "Trip computer".

To switch trip computer on/off and to reset all
values to zero:

1. If necessary, move the highlight marker to

the third field from the top.

2. Press the MINI joystick.

Other menu items are displayed.

3. Select the desired menu item.

> "Start"

> "Stop"

> "Reset"

> Departure time

> Driving time

> Distance traveled

> Average speed

> Average fuel consumption

56

Settings and information

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Operating principle

Certain settings and information are only avail­able when the ignition is switched on, the vehi­cle is at a standstill and the doors are closed.

1 Button for:

> Selecting display

> Setting values

> Confirming selected display or set values

> Calling up computer information 54

Exiting displays

1. Briefly press the button in the turn indicator

lever repeatedly until "HOME" is displayed.

2. Press the button for a longer period.

2 Calling up Check Control 63

3 Displaying vehicle check 64

4 Setting the time 61

5 Setting the date 62

6 Exiting the menu

The display again shows the outside tempera­ture and the time.

Displays are also exited if no entries are made
for approx. 8 seconds.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

57

Next setting or item of information

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Service requirements

1. Within a setting or item of information,

briefly press the button in the turn indicator
lever repeatedly until "NEXT" is displayed.

2. Press the button for a longer period.

The display changes directly to the next setting
or item of information.

Units of measure

To set the units of measure. The settings are
stored for the remote control currently in use,
refer also to Personal Profile on page 26.

Everything under control

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Language / Units".

5. Select "Units".

The remaining driving distance and the date of
the next scheduled service are briefly displayed
immediately after you start the engine or switch
on the ignition.

The extent of service work required can be
read out from the remote control by your

MINI Dealer.<

6. Select the menu item to be set.

7. Select the desired unit of measure.

58

Possible displays

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

1 Button for selecting information

2 Engine oil

3 Front brakes

4 Rear brakes

5 Vehicle check

Supplementary information

You can have further information on the scope
of maintenance displayed on the Control Dis­play, refer to page 16.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Info sources".

6 Roadworthiness test

7 Brake fluid

8 Exit display 57

9 Next setting or item of information 58

More information on the MINI Maintenance Sys­tem can be found on page 167.

4. Select "Service Info".

5. Select "Service requirements".

6. If necessary, move the highlight marker to

the second field from the top. Select "Status".

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

59

A list of selected maintenance operations and, if

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

applicable, inspections required by law is dis­played.

You can have further information displayed on
each entry:
Select an entry.

Everything under control

Exiting the menu

Select the arrow.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Info sources".

4. Select "Service Info".

5. If necessary, move the highlight marker to

the uppermost field. Select "Service require­ments".

6. Select "Status".

7. Select "State inspection".

8. Select "Set service date".

The month is highlighted.

9. Turn the MINI joystick to make the adjust-

ment.

Symbols

No service is currently required.

The deadline for service or a legally man­dated inspection is approaching. Please

schedule a service appointment.

The service deadline has already passed.

Entering deadlines for legally required
inspections*

Make sure the date on the Control Display is
always set correctly, page 62, otherwise the
effectiveness of Condition Based Service CBS is
not ensured.

60

10. Press the MINI joystick to apply the setting.

The year is highlighted.

11. Turn the MINI joystick to make the adjust-

ment.

12. Press the MINI joystick to apply the setting.

The date entry is stored.

Exiting the menu

Select the arrow.

Clock

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

On the onboard monitor

In the tachometer

Setting the time

1. Briefly press the button in the turn indicator

lever repeatedly until "SET/INFO" is dis­played.

2. Press and hold the button until the display

changes.

3. Briefly press the button repeatedly until the

symbol and "SET" are displayed.

Setting the time

1. Press the button once or twice until the

start menu appears.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Turn the MINI joystick until "Settings" is

selected and press the MINI joystick.

NAVIGATIONREFERENCE

4. Press and hold the button until the display

changes.

5. Press the button to set the hours.

6. Wait for the display to change to minutes.

7. Press the button to set the minutes.

8. Wait for the display to change.

The settings are stored.

4. Turn the MINI joystick until "Time / Date" is

selected and press the MINI joystick.

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

61

5. Turn the MINI joystick until "Time" is

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

selected and press the MINI joystick.

Switching on the hour signal*

You will hear three tones just before each full hour.

Select "Hour memo".

The hour signal is activated.

The settings are stored for the remote control
currently in use, refer also to Personal Profile on
page 26.

Date

6. Turn the MINI joystick until "Set time" is

selected and press the MINI joystick.

Everything under control

7. Turn the MINI joystick to set the hours and

press the MINI joystick.

8. Turn the MINI joystick to set the minutes and

press the MINI joystick.

The system accepts the new time.

Setting the time format

The settings are stored for the remote control
currently in use, refer also to Personal Profile on
page 26.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Time / Date".

5. Select "Time".

6. Select "Time format".

7. Select the desired format.

In the tachometer

Setting the date

1. Briefly press the button in the turn indicator

lever repeatedly until "SET/INFO" is displayed.

2. Press and hold the button until the display

changes.

3. Briefly press the button repeatedly until the

symbol and "SET" are displayed.

4. Press and hold the button until the display

changes.

5. Press the button to set the day of the month.

6. Wait for the display to change to month.

7. Set the month and year in the same way.

8. Wait for the display to change.

The settings are stored.

62

On the onboard monitor

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Check Control

Setting the date

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Time / Date".

5. Select "Date".

6. Select "Set date".

7. Turn the MINI joystick to make the adjust-

ment.

8. Press the MINI joystick to apply the setting.

The next setting is highlighted.

9. Make the remaining adjustments. After the

last adjustment, the date is stored.

The concept

The Check Control monitors vehicle functions
and alerts you to any malfunctions in the sys­tems monitored. Check Control messages
involve indicator and warning lamps in the dis­play and, in some circumstances, an acoustic
signal as well as text messages at the bottom of
the Control Display.

Indicator and warning lamps

Indicator and warning lamps can light up in var­ious combinations and colors in the indicator
areas 1 and 2.

Explanatory text messages

NAVIGATIONREFERENCE

Setting the date format

The settings are stored for the remote control
currently in use, refer also to Personal Profile on
page 26.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Time / Date".

5. Select "Date".

6. Select "Date format".

7. Select the desired format.

Text messages at the lower edge of the Control
Display explain the meaning of the displayed
indicator and warning lamps.

63

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

For most Check Control messages, you can view

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

more information later, e.g. regarding the cause
of a malfunction and how to respond, refer to
page 65.

In urgent cases, this information will be shown
as soon as the corresponding lamp comes on.

To exit the displayed information:

Select the arrow.

Other Check Control messages are automatically
hidden after approx. 20 seconds, but remain
stored.

They are marked with the symbol shown
here.

This symbol indicates that Check Control
messages have been stored. Check Control mes­sages can be viewed whenever it is convenient.

Hiding Check Control messages

Everything under control

Press the button in the turn indicator lever.

Some Check Control messages are displayed
until the malfunctions have been rectified. They
cannot be hidden. If several malfunctions occur
at the same time, they are displayed in succes­sion.

They are marked with the symbol shown
here.

Viewing stored Check Control messages

Stored Check Control messages can only be dis­played if the driver's door is closed.

1. Briefly press the button in the turn indicator

lever repeatedly until "SET/INFO" is dis­played.

2. Press and hold the button until the display

changes.

64

3. Press the button repeatedly until the display

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

shows the corresponding symbol and
"CHECK INFO".

4. Hold the button down.

"CHECK OK" appears if there are no Check
Control messages.
If a Check Control message has been stored,
the corresponding message is displayed. In
addition, the text message appears on the
Control Display.

5. Briefly press the button to check for other

messages.

Viewing more information later

Onboard monitor, for operating principle refer
to page 16.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Info sources".

4. Select "Service Info".

5. If necessary, move the highlight marker to

the uppermost field. Select "Check Control
messages".

6. Select a text message.

Exit display:

Select the arrow.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

65

Speed limit

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Stopwatch

Enter a speed, and a Check Control message will
indicate when you reach this speed. This enables
you, for example, to receive warnings if you
exceed a speed limit in an urban area.
You are only warned of reaching this speed a
second time if your vehicle speed falls below it
again by at least 3 mph or 5 km/h.

Displaying, setting or changing the limit

Onboard monitor, for operating principle refer
to page 16.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Naviga-

tion" and press the MINI joystick.

3. Select "Car Data".

4. Select "Limit".

Everything under control

5. Select "Change limit:".

6. Turn the MINI joystick to set the limit.

7. Press the MINI joystick to apply the setting.

The limit is automatically activated.

Applying your current speed as limit

Select "Select current speed".
The system adopts your current speed as the
limit.

Onboard monitor, for operating principle refer
to page 16.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Naviga-

tion" and press the MINI joystick.

3. Select "Car Data".

4. Select "Stopwatch" .

Starting, stopping or resetting

> Select "Start".

The stopwatch starts at the displayed time.

> Select "Reset".

The stopwatch is reset and restarts if it was
running beforehand.

> Select "Stop".

This stops the timer.

Taking an interim time reading

Select "Interim time".
The interim time appears below the ongoing pri­mary stopwatch count.

All of the remaining functions remain available
at all times while the stopwatch is running. The
stopwatch continues operation in the back­ground.

Activating the limit

Select "On".

Limit is activated.

66

Altering settings

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Language on the Control Display

The language of the Control Display can be set.
Refer to the basic principles on page 16. The set­ting is stored for the remote control currently in
use.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Language / Units".

5. Select "Language".

Brightness of the Control Display

The brightness is automatically adapted to the
ambient lighting conditions. Note, however,
that you can change the basic setting while the
low beams are switched on. The setting is stored
for the remote control currently in use.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Display settings".

5. Select "Brightness".

6. Select "Brightness".

7. Turn the MINI joystick until the desired set-

ting is reached.

NAVIGATIONREFERENCE

6. Select "Text language".

The language for the display texts and navi­gation messages can be changed.

7. Select the desired language.

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

67

Technology for driving comfort

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

and safety

Park Distance Control PDC*

The concept

PDC assists you with parking backwards. Acous­tic signals and a visual indicator
presence of an object behind the vehicle. To
measure the distance, there are four ultrasonic
sensors in either bumper.

These sensors have a range of approx. 6.5 ft/
2 m. However, an acoustic warning does not
sound until an object is approx. 24 in/60 cm
from the rear corner sensors, or approx. 5 ft/

1.50 m from the rear center sensors.

PDC is a parking aid that can indicate

objects when they are approached slowly,
as is usually the case when parking. Avoid
approaching an object at high speed, otherwise
physical circumstances may lead to the system
warning being issued too late.<

Automatic mode

With the engine running or the ignition switched
on, the system is activated automatically after
approx. 1 second when you engage reverse gear
or move the automatic transmission selector lever
to position R. Wait this short period before driving.

warn you of the

To avoid this problem, keep the sensors clean
and free of ice or snow in order to ensure that
they will continue to operate effectively. When
using a high-pressure cleaner, do not direct the
jet toward the sensors for lengthy periods and
only spray from a distance of at least 4 in/10 cm.

PDC with visual warning

To have the system show distances to objects on
the Control Display. The contours of distant
objects are shown on the Control Display even
before the acoustic signal sounds.

Onboard monitor, for operating principle refer
to page 16.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

Acoustic signals

As the distance between vehicle and object
decreases, the intervals between the tones
become shorter. If the distance to the nearest
object falls to below roughly 1 ft/30 cm, then a
continuous tone sounds.

Technology for driving comfort and safety

If the distance remains constant, e.g. when driv­ing parallel to a wall, the acoustic signal stops
after approx. 3 seconds.

Malfunction

Indicator lamp comes on: PDC is malfunc­tioning. A message appears on the Con­trol Display. Have the system checked.

68

4. Select "Vehicle and tires".

5. If necessary, move the highlight marker to

the uppermost field. Select "PDC" .

6. Select "PDC display on".

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The PDC display is activated. It is shown on

the Control Display as soon as PDC is activated.

The setting is stored for the remote control in use.

System limitations

Even with PDC, final responsibility for esti-

mating the distance between the vehicle
and any obstructions always remains with the
driver. Sensors, too, have blind spots in which
objects cannot be detected. Moreover, ultra­sonic detection can reach its physical limits with
objects such as trailer tow bars and couplings,
thin and wedge-shaped objects, etc. Low
objects already indicated, such as curbs, may
enter the sensors' blind spots before or after a
continuous audible signal is given. Higher, pro­truding objects, such as wall ledges, may not be
detectable. Therefore, always drive cautiously,
otherwise there is a risk of personal injury or
property damage. Loud sound sources outside
or inside the car can drown out the PDC signal.<

Driving stability control systems

Your MINI has a number of systems that help to
maintain the vehicle's stability even in adverse
driving conditions.

The laws of physics cannot be repealed,

even with driving stability control systems.
An appropriate driving style always remains the
responsibility of the driver. Therefore do not
reduce the additio nal safety margin by engaging
in hazardous driving thereby running the risk of
an accident.<

Antilock Brake System ABS

ABS prevents locking of the wheels during brak­ing. Safe steering response is maintained even
during full braking. Active safety is thus
increased.

Braking safely, refer to page 95.

Among others, ABS includes the following func­tions:

> Cornering Brake Control CBC

> Electronic brake-force distribution EBV

> Brake Assist

Cornering Brake Control CBC

Driving stability and steering characteristics are
further enhanced while braking in turns or dur­ing a lane change.

Electronic brake-force distribution EBV

The system controls the brake pressure in the
rear wheels to ensure stable braking behavior.

Brake Assist

Rapidly depressing the brake causes this system
to automatically develop maximum braking
force. Thus, the system helps keep braking dis­tance to a minimum. At the same time, all the
benefits provided by ABS are exploited.

Do not reduce the pressure on the brake for the
duration of the full braking application.

Dynamic Stability Control DSC

DSC prevents the driving wheels from losing trac­tion when you pull away from rest or accelerate.
The system also recognizes unstable driving con­ditions, for example if the rear of the car is about
to swerve or if momentum is acting at an angle
past the front wheels. In these cases, DSC helps
the vehicle maintain a safe course within physical
limits by reducing engine output and through
braking actions at the individual wheels.

DSC also encompasses the following functions:

> Antilock Brake System ABS

> Electronic brake-force distribution EBV

> Brake Assist

> Cornering Brake Control CBC

> Hill Start Assist

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

69

Deactivating DSC

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Press the button repeatedly until the DSC indica­tor lamps come on. DSC is deactivated. Stabiliz­ing and propulsion promoting actions are no
longer executed.

When driving with snow chains or to 'rock free'
in snow, it can be helpful to switch off DSC for a
brief period.

To increase vehicle stability, activate DSC again
as soon as possible.

Activating DSC

Press the button again: the DSC indicator lamps
go out.

> when driving with snow chains

Activating DTC

Press the button: the DTC indicator lamps come
on.

For better control

If the indicator lamp flashes:
DTC controls the driving and breaking
forces.

If the indicator lamps are on:
DTC is activated.

For better control

If the indicator lamp flashes:
The DSC controls the driving and
breaking forces.

If the indicator lamps are on:
DSC is deactivated.

Dynamic Traction Control DTC*

DTC is a type of DSC that is propulsion optimized
for special road conditions such as uncleared
snowy roads. The system ensures maximum pro­pulsion though with restricted driving stability.

Technology for driving comfort and safety

You therefore need to drive with suitable caution.

In the following exceptional situations, it can be
useful to briefly activate DTC:

> when driving on snow-covered inclines, in

slush, or on uncleared snowy roads

> when rocking the vehicle free, driving out of

deep snow or on loose surfaces

70

Deactivating DTC

Press the button again: the DSC indicator lamps
go out.

Deactivating both DTC and DSC

Press the button for at least 3 seconds: the DSC
indicator lamps come on. The dynamic traction
control (DTC) and dynamic stability control (DSC)
are both deactivated. There will be no more sta­bilizing interventions.

Interventions (differential lock) in braking occur to
improve propulsion when drive wheels are rotat­ing unevenly, even when the DSC is deactivated.

Activating DSC

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Press the button again: the indicator lamps
go out.

Hill Start Assist*

Hill Start Assist aids you in comfortably driving
off on inclines. It is not necessary to use the
parking brake for this.

1. Hold the MINI with the brake.

2. Release the brake and immediately drive

off.

Hill Start Assist holds the car in place for approx.
2 seconds after the brake is released.

Depending on the load and gradient, the

vehicle can roll backward slightly during
this period. After you release the brake, immedi­ately start driving since the hill start assist only
holds the vehicle for about 2 seconds, and it will
start to roll backwards.<

Sport button*

Pressing the button causes your MINI to respond
even more sportily.

> Engine responds more spontaneously to

movements of the accelerator.

> Steering response is more direct.

With automatic transmission:

> More rapid gear shifting in Sport program.

Activating the system

Deactivating the system

> Press the SPORT button again.

> Switch off the engine.

Flat Tire Monitor FTM*

The concept

The Flat Tire Monitor detects pressure loss in a
tire by comparing the rotating speeds of the
individual tires while moving.

If a tire loses pressure, its rolling circumference
changes, and this in turn alters the speed of
rotation. This change is detected and is reported
as a flat tire.

Functional requirement

In order to assure the reliable reporting of a flat
tire, the system must be initialized for the cor­rect tire inflation pressure.

Each time you correct the pressure in a
tire, or change a wheel or tire, the system

must be reinitialized.<

System limitations

The Flat Tire Monitor is unable to warn the driver
of sudden, severe tire damage caused by exter­nal factors, nor can it identify the gradual loss of
pressure that will inevitably occur in all four tires
over a lengthy period of time.

In the following situations, the system could be
delayed or malfunction:

> System has not been initialized

> Driving on snowy or slippery road surface

> Performance-oriented style of driving: slip in

the drive wheels, high lateral acceleration

> Snow chains are attached

When the vehicle is driven with a space-saver
spare tire
not function.

*

, page 180, the Flat Tire Monitor can-

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

Press the SPORT button.
The LED lights up.

SPORT is briefly displayed in the tachometer.

71

Initializing the system

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The initialization is completed during driv-

ing, which can be interrupted at any time.
When driving resumes, the initialization is con­tinued automatically.
Do not initialize the system if you are driving

*

with snow chains or a space-saver spare tire

.<

Using the button in the turn indicator
lever

1. Start the engine, but do not start driving.

2. Briefly press the button in the turn indicator

lever repeatedly until "SET/INFO" is dis­played.

3. Press and hold the button until the display

changes.

4. Briefly press the button repeatedly until the

corresponding symbol and "RESET" are dis­played.

Using the onboard monitor

Onboard monitor, for operating principle refer
to page 16.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Vehicle and tires".

5. If necessary, move the highlight marker to

the uppermost field. Select "FTM".

5. Press and hold the button until the display

Technology for driving comfort and safety

changes.

6. Start driving.

Initialization is completed while the car is on
the move, without any feedback.

72

6. Start the engine, but do not start driving.

7. Select "Reset".

8. Select "Yes".

9. Start driving.

The initialization is completed during driv­ing.

Indication of a flat tire

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The warning lamps come on in yellow
and red. A message appears on the
Control Display. An acoustic signal also
sounds. There is a flat tire or substantial

loss of tire pressure.

1. Reduce speed and stop the vehicle with cau-

tion. Avoid sudden braking and steering
maneuvers.

2. Check whether your vehicle is equipped

with normal tires or Run-Flat Tires.

The symbol identifying Run-Flat Tires
is a circle with the letters RSC on the

sidewall, refer to Run-Flat Tires, page 161.<

Normal tires

1. Determine which tire is damaged.

If this cannot be determined, contact
your MINI Dealer.<

2. Repair the flat tire, refer to page 177, or

change the damaged tire, refer to page 179.

Run-Flat Tires*

1. Cautiously reduce speed to below 50 mph

or 80 km/h. Avoid sudden braking and
steering maneuvers. Do not exceed a speed
of 50 mph or 80 km/h.

Do not continue driving if the vehicle is
not equipped with Run-Flat Tires,

page 161, otherwise a serious accident
could result.<

2. At the next opportunity, check the air pres-

sure in all four tires.

If all four tires are inflated to the cor­rect pressures, the Flat Tire Monitor

might not have been initialized. The system
must then be initialized.<

3. In the event of complete tire pressure loss,

0 psi/0 kPa, you can estimate the possible
distance for continued driving on the basis
of the following guidelines:

> With a light load:

1 to 2 persons without luggage:
approx. 155 miles/250 km

> With a medium load:

2 persons, cargo bay full, or 4 persons
without luggage:
approx. 90 miles/150 km

> With a full load:

4 persons, load compartment full:
approx. 30 miles/50 km

Drive cautiously and do not exceed a

speed of 50 mph or 80 km/h, otherwise an
accident may occur. In the event of pressure
loss, vehicle handling changes. This includes
reduced tracking stability in braking, extended
braking distance and altered natural steering
characteristics. If unusual vibration or loud
noises occur during the journey, this may be an
indication that the damaged tire has finally
failed. Reduce the vehicle speed and stop as
soon as possible. Otherwise, sections of the tire
may come loose and cause accidents. Do not
continue driving and contact your MINI
Dealer.<

Malfunction

The warning lamps light up in yellow. A
message appears on the Control Dis­play. There is a malfunction in the Flat
Tire Monitor or the system has failed.

Have the system checked as soon as possible.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

73

Tire Pressure Monitor

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

TPM*

The concept

TPM checks the inflation pressures of the four
mounted tires. The system notifies you if there is
a significant loss of pressure in one or more tires.

Status indicator on the onboard monitor

The tire and system condition is indicated by the
color of the tires.

TPM takes into account the fact that tire pres­sure changes while the vehicle is being driven.
The tire pressure does not need to be corrected
unless the TPM instructs you to do so by means
of color indicators.

Functional requirement

In order to assure the reliable reporting of a flat
tire, the system must be reset while all tire infla­tion pressures are correct.

Always use wheels with TPM electronics. Other­wise, the system may malfunction.

Each time a tire inflation pressure has
been corrected or a wheel or tire has been

changed, reset the system.<

System limitations

TPM cannot warn you in advance of sud­de n seve re ti re dam age ca used by out side

influences.<

The system does not work correctly if it has not
been reset; for example, a flat tire may be indi­cated even though the tire inflation pressures
are correct.

The system is inactive and cannot indicate a flat
tire if a wheel without TPM electronics, such as a
compact spare wheel*, has been mounted, or if
TPM is temporarily malfunctioning due to other
systems or devices using the same radio fre­quency.

Green

The tire inflation pressure corresponds to the
established target value.

"TPM active" is displayed on the onboard moni­tor.

One wheel yellow

There is a flat tire or substantial loss of tire pres­sure in the indicated tire. A message appears on
the onboard monitor.

All wheels yellow

There is a flat tire or substantial loss of tire pres­sure in several tires. A message appears on the
onboard monitor.

Gray

The system cannot detect a puncture.

Possible reasons for this:

> TPM is being reset

> Temporary malfunction caused by systems

or devices using the same radio frequency

> Malfunction

Technology for driving comfort and safety

74

Resetting the system

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Each time a tire inflation pressure has
been corrected or a wheel or tire has been

changed, reset the system.<

Using the button in the turn indicator lever

1. Start the engine, but do not start driving.

2. Briefly press the button in the turn indicator

lever repeatedly until "SET/INFO" is displayed.

3. Press and hold the button until the display

changes.

4. Repeatedly press the button briefly until the

symbol for Tire Pressure Monitor and
"ACTIVE" are displayed.
The Tire Pressure Monitor can be reset using
"RESET".

6. Start driving.

After driving a few minutes, the set inflation
pressures in the tires are accepted as the tar­get values to be monitored. The system
reset is completed during your drive, and
can be interrupted at any time. When driving
resumes, the reset is continued automati­cally. The indicator lamp goes out after the
system reset is completed.

Using the onboard monitor

Onboard monitor, for operating principle refer
to page 16.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings" and press the MINI joystick.

NAVIGATIONREFERENCE

5. Press and hold the button until "RESETTING"

appears.

4. Select "Vehicle and tires" and press the MINI

joystick.

5. If necessary, move the highlight marker to

the uppermost field. Select "TPM" and press
the MINI joystick.

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

6. Start the engine, but do not start driving.

7. Select "Reset" and press the MINI joystick.

75

8. Select "Yes" and press the MINI joystick.

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

9. Start driving.

The tires are shown in gray and "Resetting
TPM..." is displayed.

After driving a few minutes, the set inflation
pressures in the tires are accepted as the target
values to be monitored. The system reset is
completed during your drive, and can be inter­rupted at any time. When driving resumes, the
reset is continued automatically. On the
onboard monitor, the tires are shown in green
and "Status: TPM active" is displayed again.

If a flat tire is detected while the system is

being reset and while it is determining the
inflation pressures, all tires on the onboard mon­itor are displayed in yellow. The message "Tire
low!" is shown.<

Message for low tire inflation pressure

The warning lamps come on in yellow
and red. A message appears on the
onboard monitor. An acoustic signal
also sounds. There is a flat tire or sub-

stantial loss of tire pressure.

1. Reduce speed and stop the vehicle with cau-

tion. Avoid sudden braking and steering
maneuvers.

2. Check whether your vehicle is equipped

with normal tires or Run-Flat Tires.

Technology for driving comfort and safety

The symbol identifying Run-Flat Tires
is a circle with the letters RSC on the

sidewall, refer to the Owner's Manual for Ve­hicle.<

Normal tires

1. Determine which tire is damaged.

If this cannot be determined, contact
your MINI Dealer.<

2. Repair the flat tire or change the damaged

tire, refer to page 179.

Run-Flat Tires*

1. Cautiously reduce speed to below 50 mph/

80 km/h. Avoid sudden braking and steering
maneuvers. Do not exceed a speed of
50 mph/80 km/h.

Do not contin ue driving if the vehicle is
not equipped with Run-Flat Tires, oth-

erwise a serious accident could result.<

2. In the event of complete tire pressure loss,

0 psi/0 kPa, you can estimate the possible
distance for continued driving on the basis
of the following guidelines:

> With a light load:

1 to 2 persons without luggage:
approx. 155 miles/250 km

> With a medium load:

2 persons, cargo bay full, or 4 persons
without luggage:
approx. 90 miles/150 km

> With a full load:

4 persons, load compartment full:
approx. 30 miles/50 km

Drive cautiously and do not exceed a

speed of 50 mph/80 km/h, otherwise an
accident may occur. In the event of pressure
loss, vehicle handling changes. This includes
reduced tracking stability in braking, extended
braking distance and altered natural steering
characteristics. If unusual vibration or loud
noises occur during the journey, this may be an
indication that the damaged tire has finally
failed. Reduce the vehicle speed and stop as
soon as possible. Otherwise, sections of the tire
may come loose and cause accidents. Do not
continue driving and contact your MINI
Dealer.<

76

Malfunction

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The small warning lamp flashes in yel­low and then lights up continuously; the
larger warning lamp comes on in yel-

low.
On the onboard monitor, the tires are shown in
gray and a message appears. No punctures can
be detected.

This type of message is shown in the following
situations:

> If there is a malfunction

Have the system checked.

> If a wheel without TPM electronics has been

mounted

> If TPM is temporarily malfunctioning due to

other systems or devices using the same
radio frequency.

Message for unsuccessful system reset

Both warning lamps come on in yellow.

A message appears on the onboard

monitor. The system is not reset after a

tire has been changed, for example.

Check the tire inflation pressure and reset the
system, refer to the Owner's Manual for Vehicle.

Declaration according to NHTSA/
FMVSS 138 Tire Pressure Monitoring
Systems

Each tire, including the spare, should be
checked monthly when cold and inflated to the
inflation pressure recommended by the vehicle
manufacturer on the vehicle placard or tire infla­tion pressure label. If your vehicle has tires of a
different size than the size indicated on the vehi­cle placard or tire inflation pressure label, you
should determine the proper tire inflation pres­sure for those tires. As an added safety feature,
your vehicle has been equipped with a tire pres­sure monitoring system TPMS that illuminates a
low tire pressure telltale when one or more of
your tires are significantly under-inflated.
Accordingly, when the low tire pressure telltale
illuminates, you should stop and check your tires
as soon as possible, and inflate them to the
proper pressure. Driving on a significantly
under-inflated tire causes the tire to overheat
and can lead to tire failure. Underinflation also
reduces fuel efficiency and tire tread life, and
may affect the vehicle's handling and stopping
ability. Please note that the TPMS is not a substi­tute for proper tire maintenance, and it is the
driver's responsibility to maintain correct tire
pressure, even if underinflation has not reached
the level at which the TPMS low tire pressure tell­tale illuminates.

The TPMS malfunction indicator is combined
with the low tire pressure telltale. When the sys­tem detects a malfunction, the telltale will flash
for approximately one minute and then remain
continuously lit. This sequence will continue
upon subsequent vehicle startups as long as the
malfunction exists. When the malfunction indi­cator is illuminated, the system may not be able
to detect or signal low tire pressure as intended.
TPMS malfunctions may occur for a variety of
reasons, including the installation of replace­ment or alternate tires or wheels on the vehicle
that prevent the TPMS from functioning prop­erly. Always check the TPMS malfunction telltale
after replacing one or more tires or wheels on
your vehicle to ensure that the replacement or
alternate tires and wheels allow the TPMS to
continue to function properly.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

77

Airbags

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The following airbags are located under the
marked covers:

Protective action

Observe the instructions on page 36 to
ensure the best possible personal protec-

tion.<

The front airbags help protect the driver and
front passenger by responding to frontal
impacts in which safety belts alone cannot pro­vide adequate restraint. When needed, the head
and side airbags help provide protection in the
event of side impact. The relevant side airbag
supports the side upper body area. The head air
bag supports the head.

The airbags are designed to not be triggered in
every type of collision, e.g. not in minor acci­dents, certain rollover situations or rear impacts.

Do not apply adhesive materials to the

cover panels of the airbags, cover them or
modify them in any other way.
Keep the dashboard and window on the passen­ger side free from obstruction, i.e. do not cover it
with adhesive film or coverings, and do not affix
any holders such as for a navigation device or a
mobile phone.
Do not attach seat covers, cushions or other

Technology for driving comfort and safety

objects not specifically approved for seats with
integral side airbags to the front seats. Do not
hang items of clothing such as coats or jackets
over the backrests. Do not attempt to remove
the airbag retention system from the vehicle. Do
not modify the individual components of the
system or its wiring in any way. This includes the
upholstered covers on the steering wheel,

1 Front airbags

2 Side airbags in backrests

3 Head airbags at the front and rear

instrument panel, seats and roof posts, as well as
the sides of the roof lining. Do not attempt to
remove or dismantle the steering wheel.
Do not touch the individual components imme­diately after the system has been triggered,
because there is a danger of burns.
In the event of malfunctions, deactivation, or
triggering of the airbag restraint system, have
the testing, repair, removal, and disposal of air­bag generators executed only by a MINI Dealer
or a workshop that works according to repair
procedures of the manufacturer of your MINI
with correspondingly trained personnel and has
the required explosives licenses. Otherwise,
unprofessional attempts to service the system
could lead to failure in an emergency or undes­ired airbag activation, either of which could
result in personal injury.<

Warning notices and information about the air­bags can also be found on the sun visors.

Automatic deactivation of the front
passenger airbags

An analysis of the impression in the front pas­senger seat cushion determines whether and
how the seat is occupied. The front and side air­bags for the front passenger are activated or
deactivated by the system accordingly.

78

The indicator lamp above the interior rear-

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

view mirror shows the current status of
the front passenger airbags, deactivated or acti­vated, refer to Status of front passenger airbags
below.<

Before transporting a child on the front

passenger seat, read the safety precautions
and handling instructions under Transporting
children safely, page 42.
The front and side airbags can also be deacti­vated by adolescents and adults sitting in certain
positions; the indicator lamp for the front passen­ger airbags comes on. In such cases, the passen­ger should change his or her sitting position so
that the front passenger airbags are activated
and the indicator lamp goes out. If the desired
airbag sta tus cannot be achieved by changing the
sitting position, transport the relevant passenger
on a rear seat. Do not attach covers, cushions, ball
mats or other items to the front passenger seat
unless they are specifically recommended by the
manufacturer of your MINI. Do not place any
items under the seat which could press against
the seat from below. Otherwise a correct analysis
of the seat cushion is not ensured.<

The front and side airbags for the front pas­senger are not activated.

Most child seats are detected by the

system. This particularly applies to
child seats that were required by the NHTSA
at the time of manufacture of the vehicle.
After installing a child's seat, check that the
indicator lamp for the front passenger air­bags comes on. It indicates that the child's
seat has been detected and that the front
passenger airbags are deactivated.<

> Th e i nd ic at or la mp do es no t c om e o n a s l on g

as a person of sufficient size and in a correct
sitting position is detected on the seat.
The front and side airbags for the front pas­senger are activated.

> The indicator lamp does not come on if the

seat is empty.
The front and side airbags for the front pas­senger are not activated.

Operational readiness of airbag system

Status of front passenger airbags

The indicator lamp for the front passenger air­bags shows the functional status of the front
passenger's front and side airbag s in accordance
with whether and how the front passenger seat
is occupied. The indicator lamp shows whether
the front passenger airbags are activated or
deactivated.

> The indicator lamp comes on as intended

when a child in a specially designated child­restraint system is detected on the seat.

As of radio readiness, page 44, the warning
lamp comes on briefly to indicate that the entire
airbag system and the belt tensioners are oper­ational.

Airbag system malfunction

> The warning lamp does not come on when

radio readiness or the ignition is switched
on.

> The warning lamp stays lit continuously.

In the event of a fault in the airbag system,

have it checked without delay, otherwise
there is the risk that the system will not function
as intended even if a sufficiently severe accident
occurs.<

79

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

Lamps

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Parking lamps/low beams

Lamps

0 Lamps off and daytime running lamps

1 Parking lamps and daytime running lamps

2 Low-beam headlamps and welcome lamps

3 Automatic headlamp control

ning lamps and welcome lamps

When you open the driver's door with the igni­tion switched off, the exterior lighting is auto­matically switched off if the light switch is in
position 0, 2 or 3.

Switch on the parking lamps if necessary, switch
position 1.

Parking lamps

Turn the light switch to position 1.
The front, rear and side vehicle lighting is
switched on.

Activation of lights on one side of the vehicle for
parking, page 81.

The parking lamps will discharge the bat-

tery. Therefore, do not leave them on for
unduly long periods of time, otherwise the bat­tery might not have enough power to start the
engine.<

Low beams

Turn the light switch to position 2.
The low beams come on when the ignition is on.

*

, daytime run-

Automatic headlamp control*

When the switch is in position 3, the low beams
are switched on and off automatically depend­ing on ambient light conditions, e.g. in a tunnel,
in twilight, or if there is precipitation.

The headlamps may also come on when the sun
is sitting low on a blue sky.

When driving into tunnels with bright overhead
lights, there may be a delay before the head­lamps come on.

The low beams remain switched on indepen­dent of the ambient lighting conditions when

*

you switch on the fog lamps

If the daytime running lamps are activated,
page 81, the low beams are always switched on
with the light switch in position 3 and the igni­tion on. The exterior lamps are automatically
switched off after the vehicle is parked.

The automatic headlamp control cannot

serve as a substitute for your personal
judgment in determining when the lamps
should be switched on in response to ambient
lighting conditions. For example, the system
cannot detect fog or hazy weather. To avoid
safety risks, you should respond to these kinds
of low-visibility situations by switching the head­lamps on manually.<

.

Welcome lamps

If you leave the light switch in the low beam or
automatic headlamp control position when you
switch off the ignition, the parking lamps and
interior lamps come on for a certain time as soon
as the vehicle is unlocked.

Pathway lighting

If you activate the headlamp flasher after park­ing the car, with the lights switched off, the low
beams come on and remain on for a certain
time.

The setting is stored for the remote control in
use, refer to Personal Profile, page 26.

80

Setting the duration or deactivating the

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

function

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Vehicle and tires".

5. Select "Lighting".

6. Select "Pathway lighting".

7. Turn the MINI joystick to select the corre-

sponding duration.

8. Press the MINI joystick to apply the setting.

5. Select "Lighting".

6. Select "Daytime running lamps".

The daytime running lamps are switched on.

High beams/roadside parking lamps

Daytime running lamps*

The light switch can remain in the lamps off,
parking lamps or automatic headlamp control*
position.
In the lamps off position, the exterior lighting is
automatically switched off after the vehicle is
parked. In the parking lamps position, the park­ing lamps will stay on after the ignition is
switched off.

Switch on the parking lamps separately if needed.

Activating/deactivating daytime
running lamps

The setting is stored for the remote control in
use, refer to Personal Profile, page 26.

1. Press the button.

This opens the start menu.

2. Move the MINI joystick to highlight "Setup"

and press the MINI joystick.

3. Select "Settings".

4. Select "Vehicle and tires".

1 Turn signal indicators/roadside parking

lamps

*

2 Switching on high beams

3 Switching off high beams/headlamp flasher

Roadside parking lamps, left or right*

The vehicle can be illuminated on one side for
parking. Comply with local regulations when
doing so.

Switching on

After parking the vehicle, press the lever up or
down, arrow 1.

The roadside parking lamps drain the bat-

tery. Therefore, do not leave them on for
unduly long periods of time, otherwise the bat­tery might not have enough power to start the
engine.<

Switching off

Press the lever up or down to the pressure point.

81

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

Fog lamps*

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Lamps

Instrument lighting

You can adjust the brightness of the instrument
lighting only when the parking lamps or the low
beams are on.

1 Fog lamps

2 Rear fog lamp

Press the respective switch to turn the lamps on/
off.

*

*

Fog lamps*

The parking lamps or low beams must be
switched on for the fog lamps to operate. The
green indicator lamp comes on when the fog
lamps are switched on.

Depending on your vehicle's equipment, the fog
lamps are switched off when you activate the
headlamp flasher or switch on the high beams.

If the automatic headlamp control is acti­vated, the low beams will come on auto-

matically when you switch on the fog lamps.<

Rear fog lamp*

The low beams or parking lamps with fog lamps
must be switched on. The yellow indicator lamp
comes on when the rear fog lamp is switched on.

Increasing brightness

Press and hold the button until the desired
brightness is reached.

Reducing brightness

Press the button briefly.

The brightness decreases every time the button
is pressed briefly.

82

Interior lamps

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The interior lamps, the footwell lamps* and the
cargo bay lamp are controlled automatically.

To avoid draining the battery, all lamps
inside the car are switched off about

8 minutes after the ignition is switched off, refer
to Start/stop button on page 44.<

Switching interior lamps on/off manually

To switch the interior lamps on/off.

Press the switch.

To switch off the interior lamps permanently,
press the button for about 3 seconds.

Ambient lighting*

The color of the ambient lighting can be
changed.

> Press the switch forward.

The color changes in stages, ultimately to
orange.

> Press the switch toward the rear.

The color changes in stages, ultimately to
blue.

Intermediate settings and colors are possible.

Reading lamps*

To switch the reading lamps on and off.

Press the switch.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

83

Climate

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Climate

1 Airflow directed toward the windshield and

side windows

2 Air to the upper body area

Draft-free ventilation 86

3 Air to the footwell

4 Air flow rate, manual

5 Automatic recirculated-air control AUC/

Recirculated-air mode

6 AUTO program

84

7 Maximum cooling

8 Air distribution, manual

9 Setting the temperature

10 Defrosting windows and removing

condensation

11 Manual cooling function

12 Rear window defroster

13 Windshield heating

Automatic climate

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

control

Comfortable interior climate

AUTO program 6 offers the ideal air distribution
and air flow rate for almost all conditions, refer
to AUTO program below. All you need to do is
select an interior temperature which is comfort­able for you.

The following sections inform you in detail about
how to adjust the settings.

Most settings are stored for the remote control
currently in use, refer also to Personal Profile set­tings on page 26.

Air flow rate, manual

Press the – button to reduce air flow. Press
the + button to increase it.

You can reactivate the automatic mode
for the air flow rate with the AUTO button.

The air flow rate is lowered or switched off
entirely to save on battery power. The display
remains the same.

Switching the system on/off

Reduce the air flow by pressing the – button
repeatedly until the system is switched off. All
indicators go out.

Press the AUTO button to switch the automatic
climate control back on.

AUTO program

The AUTO program adjusts the air

distribution to the windshield and
side windows, towards the upper body area and
into the footwell for you. The air flow rate and
your temperature specifications will be adapted
to outside influences in accordance with sea­sonal changes, e.g. sunlight.

The cooling function is automatically switched
on along with the AUTO program.

Automatic recirculated-air control AUC/
Recirculated-air mode

Switch on the desired operating
mode by pressing the button
repeatedly.

Display of operating modes

No display: outside air flows in continuously.

AUC mode: a sensor detects pollutants in
the outside air. If necessary, the system

blocks the supply of outside air and recir­culates the inside air. As soon as the concentra­tion of pollutants in the outside air has
decreased sufficiently, the system automatically
switches back to outside air supply.

At outside temperatures below approx. 417/
+5 6, the AUC mode may be restricted due to
the increased risk of window condensation.

Recirculated-air mode: the supply of out-

side air is permanently shut off. The sys-

tem then recirculates the air currently
within the vehicle.

If condensation starts to form on the

inside window surfaces, press the AUTO
button or switch off the recirculated-air mode
and, if necessary, increase the air flow rate.
The recirculated-air mode should not be used
over an extended period of time, otherwise the
air quality inside the car will deteriorate contin­uously.<

Maximum cooling

At outside temperatures above
32 7/0 6 and when the engine is
running, you obtain a maximum

cooling effect as soon as possible.

The automatic climate control goes into recircu­lated-air mode at the lowest temperature. Air
flows at maximum rate from the vents for the
upper body area. You should therefore open
them for maximum cooling.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

85

Air distribution, manual

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

The flow of air is directed to the
windows, to the upper body area or
to the footwell as selected.

You can switch the automatic air dis-

tribution back on by pressing the AUTO button.

Climate

Temperature

Set the desired temperature individually.

The automatic climate control achieves
this temperature as quickly as possible

regardless of the season, using maximum
cooling or heating power if necessary, and then
maintains it.

If you switch between different tempera­ture settings in quick succession, the auto-

matic climate control does not have enough
time to achieve the set temperature.<

Rear window defroster

The defroster is switched off auto­matically after a certain time.
Depending on your vehicle's equip-

ment, the upper wires serve as an
antenna and are not part of the rear window
defroster.

Cooling function

When the cooling function is on,
the air is cooled, dried, then
reheated according to the temper­ature setting. This function is only

available while the engine is running.

The cooling function helps prevent condensa­tion on the windows or removes it quickly.

Depending on the weather, the windshield may
fog over briefly when the engine is started. The
recirculated-air mode may be switched on auto­matically.

The cooling function is automatically switched
on along with the AUTO program. The passenger
compartment can only be cooled while the
engine is running.

Microfilter/activated-charcoal filter

The microfilter captures dust and pollen. The
activated-charcoal filter provides additional pro­tection by filtering gaseous pollutants from the
outside air. Your MINI Dealer replaces this com­bined filter as a standard part of your scheduled
maintenance.
You can call up further information in the service
requirements display, page 58.

Defrosting windows and removing
condensation

Quickly removes ice and condensa-

tion from the windshield and front

side windows.

For this purpose, also switch on the
cooling function.

*

The windshield heating
matically.

is switched on auto-

Windshield heating*

The windshield heating is switched

off automatically after a certain

time.

86

Ventilation

1 Knob for continuous opening and closing

2 Jet for direction of air flow

Opening/closing

Turn the knob.

Direction of air flow

Swivel the entire jet.

Practical interior accessories

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Integrated universal remote control*

The concept

The integrated universal remote control can
replace as many as three hand-held transmitters
for various remote-controlled devices, such as
garage and gate openers and lighting systems.
The integrated universal remote control regis­ters and stores signals from the original hand­held transmitters.

The signal of an original hand-held transmitter
can be programmed on one of the three mem­ory buttons 1. The system in question can then
be operated by means of the programmed
memory button 1. The LED 2 flashes to confirm
transmission of the signal.

If you decide to sell your vehicle one day, in the
interest of your own security, remember to clear
the stored programs before the vehicle leaves
your possession, page 88.

To prevent possible damage or injury,

before programming or using the inte­grated universal remote control, always inspect
the immediate area to make certain that no
people, animals or objects are within the pivot­ing or travel range of the device being operated.
Comply also with the safety instructions supplied
with the original hand-held transmitter.<

Checking compatibility

If this symbol appears on the package
or in the instructions supplied with the

original hand-held transmitter, you can
assume that the radio remote control device will
be compatible with the integrated universal
remote control.

For additional information, please contact your
MINI Dealer or call: 1-800-355-3515.

You can also obtain information on the Internet
at:
www.MINI.com or
www.homelink.com

HomeLink is a registered trademark of Johnson
Controls, Inc.

Programming

1 Memory buttons

2 LED

Fixed-code hand-held transmitters

1. Switch on the ignition, page 44.

2. When starting operation for the first time:

press both outer memory buttons 1 for
approx. 20 seconds until the LED 2 flashes
rapidly. All stored programs are cleared.

3. Hold the original hand-held transmitter at a

distance of approx. 2 to 12 in/5 to 30 cm
from the memory buttons 1.

The required distance between the

hand-held transmitter and the mem­ory buttons 1 depends on the system of the
respective original hand-held transmitter
used.<

4. Simultaneously press the transmit key on

the original hand-held transmitter and the
desired memory button 1 on the integrated
universal remote control. The LED 2 flashes
slowly at first. As soon as the LED 2 flashes
rapidly, release both buttons. If the LED 2
does not flash rapidly after approx. 15 sec­onds, alter the distance.

5. To program other original hand-held trans-

mitters, repeat steps 3 and 4.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

87

The corresponding memory button 1 is now

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

programmed with the signal of the original
hand-held transmitter.

You can operate the system with the engine
running or with the ignition switched on.

If the system fails to function even after

repeated programming, check whether
the original hand-held transmitter uses an alter­nating-code system. To do so, either read the
instructions for the original hand-held transmit­ter or hold down the programmed memory
button 1 of the integrated universal remote con­trol. If the LED 2 on the integrated universal
remote control flashes rapidly and then remains
lit for about two seconds, the original hand-held
transmitter uses an alternating-code system. If it
uses an alternating-code system, program the
memory buttons 1 as described under Alternat­ing-code hand-held transmitters.<

Alternating-code hand-held
transmitters

To program the integrated universal remote
control, consult the operating instructions for
the device to be set. You will find information
there on the possibilities for synchronization or
programming of additional hand-held transmit-

Practical interior accessories

ters.
When programming hand -held transmitters that
employ an alternating code, please observe the
following supplementary instructions:

Programming will be easier with the aid of

a second person.<

1. Park your vehicle within the range of the

remote-controlled device.

2. Program the integrated universal remote

control as described above in the section
Fixed-code hand-held transmitters.

3. Locate the button on the receiver of the

device to be set, e.g. on the drive unit.

4. Press the button on the receiver of the

device to be set. After step 4, you have
approx. 30 seconds for the next step 5.

5. Press the programmed memory button 1 of

the integrated universal remote control
three times.

The corresponding memory button 1 is now
programmed with the signal of the original
hand-held transmitter.

Clearing stored programs

Press both outer memory buttons 1 for approx.
20 seconds until the LED 2 flashes: All stored
programs are cleared.

It is not possible to clear individual programs.

Reassigning individual programs

1. Hold the original hand-held transmitter at a

distance of approx. 2 to 12 in/5 to 30 cm
from the memory buttons 1.

The required distance between the

hand-held transmitter and the mem­ory buttons 1 depends on the system of the
respective original hand-held transmitter
used.<

2. Press the desired memory button 1 of the

integrated universal remote control.

3. If the LED 2 flashes slowly after approx.

20 seconds, press the transmit key of the
original hand-held transmitter and release
both buttons as soon as the LED 2 flashes
rapidly.
If the LED 2 does not flash rapidly after
approx. 15 seconds, alter the distance and
repeat this step.

88

Glove compartment

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Center armrest*

Opening

Press the button to open the cover.
The light in the glove compartment comes on.

Closing

Fold cover up.

To prevent injury in the event of an acci­dent, close the glove compartment after

use while the vehicle is being driven.<

Ventilation*

Depending on your vehicle's equipment, it may
be possible to ventilate the glove compartment.

Storage compartment

The center armrest between the front seats con­tains either a compartment or the cover for the

*

mobile phone base plate

*

adapter

.

or the snap-in

Opening

The cover slides along guide rails and can be
opened fully by pushing it back and lifting it.

Closing

Push the cover forwards.

Connection for external audio device

NAVIGATIONREFERENCE

Opening

Turn the switch to the horizontal position, arrow.

Closing

Turn the switch to the vertical position.

Depending on the temperature setting of the air
conditioning or the automatic climate control,
high temperatures may result in the glove com­partment.

You can connect an external audio device such
as a CD or MP3 player and play audio recordings
over the vehicle loudspeakers.

> AUX-In port, refer to page 145

> USB-audio interface

*

, refer to page 146

89

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

Storage compartments

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

In the vehicle interior

Depending on your vehicle's equipment, you
will find storage compartments in the doors,
next to the rear seats and in the center console

*

are located in the passenger footwell and

Nets
on the backs of the front seat backrests.

Storage compartment on the front
passenger side*

Opening

Briefly press the bottom edge of the cover.

Closing

Push the cover back into its original position.

Practical interior accessories

To prevent injury in the event of an acci­dent, close the storage compartment after

use while the vehicle is being driven.<

Cup holders and ashtray*

*

.

Cup holders

Two cup holders are located in the front of the
center console, another is in the rear at the back
of the center console.

Do not place glass containers in the cup
holders, as this increases the risk of injury

in the event of an accident.<

Ashtray*

The ashtray is located in one of the cup holders
in the center console.

Emptying

Remove the entire ashtray.

Lighter

Clothes hooks

There are clothes hooks on the grab handles in
the rear passenger compartment.

Items of clothing hung from the hooks

must not obstruct the driver's view. Do not
hang heavy objects from the hooks, otherwise
they could endanger the car's occupants, e.g. in
case of heavy braking or sudden swerving.<

90

With the engine running or the ignition switched
on, press in the cigarette lighter.

The lighter can be pulled out as soon as it pops
back out.

Hold or touch the hot cigarette lighter by

the knob only. Holding or touching it in
other areas could result in burns.
When leaving the car, always remove the key so
that children cannot operate the cigarette
lighter and burn themselves.<

Connecting electrical

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

appliances

In your MINI, you can use electrical devices such
as a flashlight, car vacuum cleaner, etc., up to
approx. 200 watts at 12 volts, as long as one of
the following sockets is available. Avoid damag­ing the sockets by attempting to insert plugs of
unsuitable shape or size.

Power socket in cargo bay

Cigarette lighter socket

Remove the lighter* or cover from the socket.

Pull out the cover.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

91

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

AT A GLANCE

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

CONTROLS

DRIVING TIPS

DRIVING TIPS

NAVIGATION

ENTERTAINMENT

MOBILITY

REFERENCE

Things to remember when driving

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Break-in period

Moving parts need breaking-in time to adjust to
each other. Please follow the instructions below
in order to achieve the optimal service life and
economy of operation for your vehicle.

Engine and differential

Always obey all official speed limits.

Up to 1,200 miles/2,000 km

Drive at varying engine and road speeds, but do
not exceed the following:

> Gasoline engine

4,500 rpm or 100 mph/160 km/h

Avoid full-throttle operation and use of the
transmission's kick-down mode.

After driving 1,200 miles/2,000 km

Engine and vehicle speeds can be gradually
increased.

Tires

Due to technical factors associated with their
manufacture, tires do not achieve their full trac­tion potential until after an initial break-in

Things to remember when driving

period. Therefore, drive cautiously during the
first 200 miles/300 km.

Brake system

Brakes require an initial break-in period of
approx. 300 miles/500 km to achieve optimized
contact and wear patterns between brake pads
and rotors. Drive cautiously during this break-in
period.

Clutch

The function of the clutch reaches its optimal
level only after a distance driven of approx.
300 miles/500 km. During this break-in period,
engage the clutch gently.

Following part replacement

The same break-in procedures should be
observed if any of the components mentioned
above have to be renewed in the course of the
vehicle's operating life.

General driving notes

Close the tailgate

Drive the vehicle only when the tailgate is

closed. Otherwise, exhaust fumes could
penetrate the interior of the vehicle.<

If special circumstances make it absolutely nec­essary to drive with the tailgate open:

1. Close all windows and the glass sunroof.

2. Switch off the recirculated-air mode and sig-

nificantly increase the air flow rate of the
automatic climate control, page 85.

Hot exhaust system

In all vehicles, extremely high tempera-

tures are generated in the exhaust sys­tem. Do not remove the heat shields installed
adjacent to various sections of the exhaust sys­tem, and never apply undercoating to them.
When driving, standing at idle and while park­ing, take care to avoid possible contact between
the hot exhaust system and any highly flamma­ble materials such as hay, leaves, grass, etc. Such
contact could lead to a fire, with the risk of seri­ous personal injuries and property damage. Do
not touch hot exhaust tail pipes. Otherwise
there is a risk of burns.<

Hydroplaning

When driving on wet or slushy roads,

reduce road speed. If you do not, a wedge
of water can form between tires and road sur­face. This situation, known as hydroplaning, can
cause partial or complete loss of tire contact
with the road surface, so that the car cannot be
steered or braked properly.<

94

The risk of hydroplaning increases with declining

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

tread depth on the tires, refer also to Tread
depth on page 160.

Driving through water

Drive through water on the road only if it is

not deeper than 1 ft/30 cm, and then only
at walking speed at the most. Otherwise, the
vehicle's engine, the electrical systems and the
transmission may be damaged.<

Parking brake on inclines

On inclines, do not hold the vehicle with

the clutch; use the parking brake. Other­wise greater clutch wear will result.<

For information on driving off using Hill Start
Assist*, refer to page 71.

Braking safely

Your MINI is equipped with ABS. If you are in a
situation which requires full braking, it is best to
brake using maximum brake pressure. Since the
vehicle maintains steering responsiveness, you
can still avoid possible obstacles with a mini­mum of steering effort.

The pulsation of the brake pedal, together with
the sound of hydraulic regulation, indicates that
ABS is actively taking effect.

You can increase the engine's braking effect by
shifting down, all the way to first gear if neces­sary. This strategy helps you avoid placing
excessive loads on the brake system. Downshift­ing in manual mode of the automatic transmis­sion, page 47.

Never drive with the clutch held down, with

the transmission in neutral or with the
engine switched off; otherwise, engine braking
action will not be present or there will be no power
assistance to the brakes or steering.
Never allow floor mats, carpets or any other
objects to protrude into the area around the ped­als, otherwise pedal function could be impaired.<

Corrosion on brake rotors

When the vehicle is driven only occasionally,
during extended periods when the vehicle is not
used at all, and in operating conditions where
brake applications are less frequent, there is an
increased tendency for corrosion to form on
rotors, while contaminants accumulate on the
brake pads. This occurs because the minimum
pressure which must be exerted by the pads
during brake applications to clean the rotors is
not reached.

Should corrosion form on the brake rotors, the
brakes will tend to respond with a pulsating effect
that even extended application will fail to cure.

NAVIGATIONREFERENCE

Driving in wet conditions

When roads are wet or there is heavy rain, briefly
exert gentle pressure on the brake pedal every
few miles. Monitor traffic conditions to ensure
that this maneuver does not endanger other
road users. The heat generated in this process
helps dry the pads and rotors to ensure that
Then full braking force will be immediately avail­able when it is needed.

Hills

To prevent overheating and the resulting

reduced efficiency of the brake system,
drive long or steep downhill gradients in the
gear in which the least braking is required. Even
light but consistent brake pressure can lead to
high temperatures, brake wear and possibly
even brake failure.<

When the vehicle is parked

Condensation forms while the automatic climate
control is in operation, and then exits under the
vehicle. Traces of condensed water under the
vehicle are therefore normal.

In the MINI Cooper S, the coolant pump may
continue to run for some time after the engine is
switched off. This will generate noise in the
engine compartment.

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

Before driving into a car wash

Avoid car washes with tracks higher than
4 in/10 cm, otherwise the chassis could be

damaged.<

For general information about vehicle care for
your MINI, refer to the chapter beginning on
page 169.

95

With convenient access and automatic

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

transmission

Insert the key into the ignition lock.
The engine can be switched off when the selec­tor lever is in position N. Refer also to page 33.

Cargo loading

To avoid loading the tires beyond their

approved carrying capacity, never over­load the vehicle. Overloading can lead to over­heating and increases the rate at which damage
develops inside the tires. The ultimate result can
assume the form of a sudden blow-out.<

Avoid fluid spills in the cargo bay as they

could damage the vehicle.<

Cargo bay cover

Do not place any objects on the cover,

otherwise they could endanger the car's
occupants, e.g. in the case of braking or sudden
swerving.<

When you open the tailgate, the cargo bay cover
is raised.

To load bulky luggage, the cover can be
removed.

1. Unhook the lift straps from the tailgate.

2. Pull the cover out of the holders toward the

Things to remember when driving

rear.

1. Pull the lever.

2. Fold rear seat backrests forward.

When folding the backrest back up, make

sure that the seat's locking mechanisms
engage properly. Otherwise, cargo could be
thrown around in the event of sharp braking or
swerving and endanger the occupants.<

Adjusting rear seat backrest*

Expand the cargo bay by raising the split rear
seat backrests to a steeper angle.

1. Pull the lever, arrow 1, and fold the rear seat

backrest forward.

2. Fold up the lever of the backrest lock until it

audibly engages, arrow 2.

3. Fold back the backrest until it engages.

If the rear seat backrests are positioned at

a steeper angle, do not install child­restraint systems in the rear of the vehicle as
their protective features may be ineffective.<

Expanding the cargo bay

The rear set backrest is split. Both sides can be
folded separately to expand the cargo bay.

96

Determining cargo limit

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

Load

1. Locate the following statement on your

vehicle's placard*:

The combined weight of occupants

and cargo should never exceed
XXX kg or YYY lbs. Otherwise, overloading
can result in damage to the vehicle and un­stable driving conditions.<

2. Determine the combined weight of the

driver and passengers that will be riding in
your vehicle.

3. Subtract the combined weight of the driver

and passengers from XXX kilograms or YYY
pounds.

4. The resulting figure equals the available

amount of cargo and luggage load capacity.
For example, if the XXX amount equals
1,400 lbs. and there will be four 150-lb. pas­sengers in your vehicle, the amount of avail­able cargo and luggage load capacity is
650 lbs:
1,400 lbs. minus 750 lbs. = 650 lbs.

5. Determine the combined weight of luggage

and cargo being loaded on the vehicle. That
weight may not safely exceed the available
cargo and luggage load capacity calculated
in step 4.

6. If your ve hicle will be towing a tra iler, part of

the load from your trailer will be transferred
to your vehicle. Consult the manual for
transporting a trailer to determine how this
may reduce the available cargo and luggage
load capacity of your vehicle.

The permissible load is the sum of the occu­pants' weights and the weight of the cargo. The
greater the weight of the occupants, the less
cargo/luggage can be transported.

Stowing cargo

> Position heavy objects as low and as far for-

ward as possible, ideally directly behind the
rear seat backrests.

> Cover sharp edges and corners.

> For very heavy cargo when the rear seat is

not occupied, secure each safety belt in the
respective opposite buckle.

> Do not stack higher than the top edge of the

backrests.

NAVIGATIONREFERENCE

MOBILITY AT A GLANCECONTROLSDRIVING TIPSENTERTAINMENT

97

Securing cargo

Online Edition for Part no. 01 41 2 601 140 - © 08/08 BMW AG

> Secure smaller and lighter items using

retaining or draw straps*.

> Heavy-duty cargo straps

and heavier objects are available at your
MINI Dealer. Four lashing eyes are provided
for attaching the cargo straps. Two of them
are located on the forward wall of the cargo
bay.
Comply with the information enclosed with
the load-securing devices.

Always position and secure the cargo as

described above, so that it cannot endan­ger the car's occupants, for example if sudden
braking or swerves are necessary.
Do not exceed the approved gross weight and
axle loads (see page 192); otherwise the vehi­cle's operating safety is no longer assured and it
will not be in compliance with the certification
regulations.

Things to remember when driving

Heavy or hard objects should not be carried
loose inside the car, since they could be thrown
around, for example as a result of heavy braking,
sudden swerves, etc., and endanger the occu­pants. Do not secure cargo using the fastening
points for the tether strap (page 43); they may
become damaged.<

*

for securing larger

Roof-mounted luggage rack*

A special rack system is available as an option for
your MINI. Your MINI Dealer will be glad to
advise you. Comply with the installation instruc­tions supplied with the rack system.

Mounting points

Remove the cover panel.

Loading roof-mounted luggage rack

Because roof racks raise the vehicle's center of
gravity when loaded, they have a major effect
on vehicle handling and steering response.
You should therefore always remember not to
exceed the approved roof load capacity, the
approved gross vehicle weight or the axle loads
when loading the rack.

You can find the applicable data under Weights
on page 192.

The roof load must be distributed uniformly and
should not be too large in area. Heavy items
should always be placed at the bottom.

When loading, make sure that there is sufficient
space for the movement of the glass sunroof
and that no objects protrude into the swiveling
area of the tailgate; otherwise damage can
occur.

Fasten roof-mounted cargo correctly and
securely to prevent it from shifting or falling off
during the trip.

Drive smoothly. Avoid sudden acceleration and
braking maneuvers, and take corners gently.

98