Loading...
Published Manual Number/ECN: MAI30VXXAE/2011093A
•Publishing System: TPAS
•Access date: 2/22/2011
•Document ECN's: Latest Available
Installation—
30015 and 30022
Cxx, Jxx, Txx, Vxx Rigid Washer-Extractors
PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.
Please Read
About the Manual Identifying Information on the Cover—The front cover displays pertinent identifying information for this manual. Most important, are the published manual number (part number) /ECN (date code). Generally, when a replacement manual is furnished, it will have the same published manual number, but the latest available ECN. This provides the user with the latest information applicable to his machine. Similarly all documents comprising the manual will be the latest available as of the date the manual was printed, even though older ECN dates for those documents may be listed in the table of contents.
When communicating with the Milnor factory regarding this manual, please also provide the other identifying information shown on the cover, including the publishing system, access date, and whether the document ECN’s are the latest available or exact.
Best Available Information—This manual contains the most accurate and complete information available when Milnor shipped your machine/software. Products are occasionally released with the best available documentation, even though the device identification (model numbers, etc.) on the documentation does not explicitly include the delivered model. In such cases, use the documentation provided.
Although unlikely, incorrect manuals may have been shipped with your machine. If you believe you received the wrong manuals, or if you need specific information about any aspect of your machine not addressed in the provided documentation, contact the Milnor Customer Service group.
References to Yellow Troubleshooting Pages—This manual may contain references to “yellow pages.” Although the pages containing trouble-shooting procedures are no longer printed on yellow paper, troubleshooting instructions, if any, will be contained in the easily located “Troubleshooting” section. See the table of contents.
Trademarks of Pellerin Milnor Corporation—The following terms, some of which may be used in this publication, are trademarks of Pellerin Milnor Corporation:
CBW® |
E-P OneTouch® |
Gear Guardian® |
Mildata® |
Milnor® |
Staph-Guard® |
E-P Express® |
E-P Plus® |
Mentor® |
Milnet® |
MultiTrac™ |
Visionex™ |
Trademarks of Other Companies—The following terms, some of which may be used in this publication, are trademarks of their respective companies:
Acronis® |
Microsoft Windows 2000® |
Yaskawa® |
Siemens® |
Atlas 2000® |
Microsoft Office XP® |
Microsoft Access® |
Seagate Crystal Reports® |
IBM® |
Microsoft Windows NT® |
Microsoft Windows XP® |
|
Comments and Suggestions
Help us to improve this manual by sending your comments to:
Pellerin Milnor Corporation
Attn: Technical Publications
P. O. Box 400
Kenner, LA 70063-0400
Fax: (504) 469-1849
Table of Contents
for MAI30VXXAE/2011093A
30015 and 30022 Cxx, Jxx, Txx, Vxx Rigid Washer-Extractors
Page |
Description |
Document/ECN |
1Limited Standard Warranty
2How to Get the Necessary Repair Components
3Safety—Rigid Washer Extractors
8 |
About the Forces Transmitted by Milnor® Washer- |
|
extractors |
10 |
Understanding the Tag Guidelines |
13 |
Understanding the Tag Guidelines |
16 |
Understanding the Tag Guidelines |
20 |
Avoiding Damage from Allied Remote Chemical |
|
Delivery Systems |
25Section 1: Installation
26Handling and Setting Procedures for Rigid Mount
|
30015 & 30022 Washer-Extractors |
30 |
Service Connections |
35 |
Section 2: Dimensional Drawings |
37 |
Dimensional Drawing - 30015C4A, C4T, & C4E |
39 |
Dimensional Drawing - 30022C4A, C4T, C4E |
41Dimensional Drawing - 30015V7J, T5E, T5J, & T5X
42Dimensional Drawing - Options 30015V7J, T5E & T5X
43Dimensional Drawing - 30022V6J, T5E, T5J, & T5X
44Dimensional Drawing - 30022V6J, T5E & T5X Options
45Dimensional Drawing - 30022V8Z
47Dimensional Drawing - 30015J4P
48Dimensional Drawing - 30015J4P Options
49Dimensional Drawing - Pedestal Base 30015/22 Vxx, Txx
BMP720097/2008272A
BIUUUD19/20081231
BIUUUS27RU/20051111
BIWUUI02/20001108
BIUUUI02RC/20110131
BIUUUI02RM/20110131
BIUUUI02RZ/20110221
BIWUUI03/20030306
MSIN0703BE/2001036V
BIRQVI01AB/20050228
BD3015C4BE/2009213D
BD3022C4BE/2009213D
BD3015V7BE/2010183D
BD3015V7BB/2002475D
BD3022V6BE/2010183D
BD3022V6BB/2006412D
BD3022V8AE/2010495D
BD3015J4AE/2001064D
BD3015J4AB/2001064D
BD30VBASAE/2007463D
PELLERIN MILNOR CORPORATION
LIMITED STANDARD WARRANTY
We warrant to the original purchaser that MILNOR machines including electronic hardware/software (hereafter referred to as “equipment”), will be free from defects in material and workmanship for a period of one year from the date of shipment (unless the time period is specifically extended for certain parts pursuant to a specific MILNOR published extended warranty) from our factory with no operating hour limitation. This warranty is contingent upon the equipment being installed, operated and serviced as specified in the operating manual supplied with the equipment, and operated under normal conditions by competent operators.
Providing we receive written notification of a warranted defect within 30 days of its discovery, we will at our option repair or replace the defective part or parts, FOB our factory. We retain the right to require inspection of the parts claimed defective in our factory prior to repairing or replacing same. We will not be responsible, or in any way liable, for unauthorized repairs or service to our equipment, and this warranty shall be void if the equipment is tampered with, modified, or abused, used for purposes not intended in the design and construction of the machine, or is repaired or altered in any way without MILNOR's written consent.
Parts damaged by exposure to weather, to aggressive water, or to chemical attack are not covered by this warranty. For parts which require routine replacement due to normal wear such as gaskets, contact points, brake and clutch linings, belts, hoses, and similar parts the warranty time period is 90 days.
We reserve the right to make changes in the design and/or construction of our equipment (including purchased components) without obligation to change any equipment previously supplied.
ANY SALE OR FURNISHING OF ANY EQUIPMENT BY MILNOR IS MADE ONLY UPON THE EXPRESS UNDERSTANDING THAT MILNOR MAKES NO EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE OR PURPOSE OR ANY OTHER WARRANTY IMPLIED BY LAW INCLUDING BUT NOT LIMITED TO REDHIBITION. MILNOR WILL NOT BE RESPONSIBLE FOR ANY COSTS OR DAMAGES ACTUALLY INCURRED OR REQUIRED AS A RESULT OF: THE FAILURE OF ANY OTHER PERSON OR ENTITY TO PERFORM ITS RESPONSIBILITIES, FIRE OR OTHER HAZARD, ACCIDENT, IMPROPER STORAGE, MIS-USE, NEGLECT, POWER OR ENVIRONMENTAL CONTROL MALFUNCTIONS, DAMAGE FROM LIQUIDS, OR ANY OTHER CAUSE BEYOND THE NORMAL RANGE OF USE. REGARDLESS OF HOW CAUSED, IN NO EVENT SHALL MILNOR BE LIABLE FOR SPECIAL, INDIRECT, PUNITIVE, LIQUIDATED, OR CONSEQUENTIAL COSTS OR DAMAGES, OR ANY COSTS OR DAMAGES WHATSOEVER WHICH EXCEED THE PRICE PAID TO MILNOR FOR THE EQUIPMENT IT SELLS OR FURNISHES.
THE PROVISIONS ON THIS PAGE REPRESENT THE ONLY WARRANTY FROM MILNOR AND NO OTHER WARRANTY OR CONDITIONS, STATUTORY OR OTHERWISE, SHALL BE IMPLIED.
WE NEITHER ASSUME, NOR AUTHORIZE ANY EMPLOYEE OR OTHER PERSON TO ASSUME FOR US, ANY OTHER RESPONSIBILITY AND/OR LIABILITY IN CONNECTION WITH THE SALE OR FURNISHING OF OUR EQUIPMENTTOANYBUYER.
BMP720097/2008272A
1
How to Get the Necessary Repair Components
BIUUUD19 (Published) Book specsDates: 20081231 / 20081231 / 20081231 Lang: ENG01 Applic: UUU
How to Get the Necessary Repair Components
This document uses Simplified Technical English.
Learn more at http://www.asd-ste100.org.
You can get components to repair your machine from the approved supplier where you got this machine. Your supplier will usually have the necessary components in stock. You can also get components from the Milnor® factory.
Tell the supplier the machine model and serial number and this data for each necessary component:
•The component number from this manual
•The component name if known
•The necessary quantity
•The necessary transportation requirements
•If the component is an electrical component, give the schematic number if known.
•If the component is a motor or an electrical control, give the nameplate data from the used component.
To write to the Milnor factory:
Pellerin Milnor Corporation
Post Office Box 400
Kenner, LA 70063-0400
UNITED STATES
Telephone: 504-467-2787
Fax: 504-469-9777
Email: parts@milnor.com
— End of BIUUUD19 —
PELLERIN MILNOR CORPORATION
2
Safety—Rigid Washer Extractors
BIUUUS27 (Published) Book specsDates: 20051111 / 20051111 / 20060322 Lang: ENG01 Applic: RUU
Safety—Rigid Washer Extractors
1. General Safety Requirements—Vital Information for Management Personnel [Document BIUUUS04]
Incorrect installation, neglected preventive maintenance, abuse, and/or improper repairs, or changes to the machine can cause unsafe operation and personal injuries, such as multiple fractures, amputations, or death. The owner or his selected representative (owner/user) is responsible for understanding and ensuring the proper operation and maintenance of the machine. The owner/user must familiarize himself with the contents of all machine instruction manuals. The owner/user should direct any questions about these instructions to a Milnor® dealer or the Milnor® Service department.
Most regulatory authorities (including OSHA in the USA and CE in Europe) hold the owner/user ultimately responsible for maintaining a safe working environment. Therefore, the owner/user must do or ensure the following:
•recognize all foreseeable safety hazards within his facility and take actions to protect his personnel, equipment, and facility;
•work equipment is suitable, properly adapted, can be used without risks to health or safety, and is adequately maintained;
•where specific hazards are likely to be involved, access to the equipment is restricted to those employees given the task of using it;
•only specifically designated workers carry out repairs, modifications, maintenance, or servicing;
•information, instruction, and training is provided;
•workers and/or their representatives are consulted.
Work equipment must comply with the requirements listed below. The owner/user must verify that installation and maintenance of equipment is performed in such a way as to support these requirements:
•control devices must be visible, identifiable, and marked; be located outside dangerous zones; and not give rise to a hazard due to unintentional operation;
•control systems must be safe and breakdown/damage must not result in danger;
•work equipment is to be stabilized;
•protection against rupture or disintegration of work equipment;
•guarding, to prevent access to danger zones or to stop movements of dangerous parts before the danger zones are reached. Guards to be robust; not give rise to any additional hazards; not be easily removed or rendered inoperative; situated at a sufficient distance from the danger zone; not restrict view of operating cycle; allow fitting, replacing, or maintenance by restricting access to relevant area and without removal of guard/protection device;
•suitable lighting for working and maintenance areas;
•maintenance to be possible when work equipment is shut down. If not possible, then protection measures to be carried out outside danger zones;
•work equipment must be appropriate for preventing the risk of fire or overheating; discharges of gas, dust, liquid, vapor, other substances; explosion of the equipment or substances in it.
PELLERIN MILNOR CORPORATION
3
Safety—Rigid Washer Extractors
1.1.Laundry Facility—Provide a supporting floor that is strong and rigid enough to support–with a reasonable safety factor and without undue or objectionable deflection–the weight of the fully loaded machine and the forces transmitted by it during operation. Provide sufficient clearance for machine movement. Provide any safety guards, fences, restraints, devices, and verbal and/or posted restrictions necessary to prevent personnel, machines, or other moving machinery from accessing the machine or its path. Provide adequate ventilation to carry away heat and vapors. Ensure service connections to installed machines meet local and national safety standards, especially regarding the electrical disconnect (see the National Electric Code). Prominently post safety information, including signs showing the source of electrical disconnect.
1.2.Personnel—Inform personnel about hazard avoidance and the importance of care and common sense. Provide personnel with the safety and operating instructions that apply to them. Verify that personnel use proper safety and operating procedures. Verify that personnel understand and abide by the warnings on the machine and precautions in the instruction manuals.
1.3.Safety Devices—Ensure that no one eliminates or disables any safety device on the machine or in the facility. Do not allow machine to be used with any missing guard, cover, panel or door. Service any failing or malfunctioning device before operating the machine.
1.4.Hazard Information—Important information on hazards is provided on the machine safety placards, in the Safety Guide, and throughout the other machine manuals. Placards must be kept clean so that the information is not obscured. They must be replaced immediately if lost or damaged. The Safety Guide and other machine manuals must be available at all times to the appropriate personnel. See the machine service manual for safety placard part numbers. Contact the Milnor Parts department for replacement placards or manuals.
1.5.Maintenance—Ensure the machine is inspected and serviced in accordance with the norms of good practice and with the preventive maintenance schedule. Replace belts, pulleys, brake shoes/disks, clutch plates/tires, rollers, seals, alignment guides, etc. before they are severely worn. Immediately investigate any evidence of impending failure and make needed repairs (e.g., cylinder, shell, or frame cracks; drive components such as motors, gear boxes, bearings, etc., whining, grinding, smoking, or becoming abnormally hot; bending or cracking of cylinder, shell, frame, etc.; leaking seals, hoses, valves, etc.) Do not permit service or maintenance by unqualified personnel.
2.Safety Alert Messages—Internal Electrical and Mechanical
Hazards [Document BIUUUS11]
The following are instructions about hazards inside the machine and in electrical enclosures.
WARNING 1 : Electrocution and Electrical Burn Hazards—Contact with electric power can kill or seriously injure you. Electric power is present inside the cabinetry unless the main machine power disconnect is off.
•Do not unlock or open electric box doors.
•Do not remove guards, covers, or panels.
•Do not reach into the machine housing or frame.
•Keep yourself and others off of machine.
•Know the location of the main machine disconnect and use it in an emergency to remove all electric power from the machine.
PELLERIN MILNOR CORPORATION
4
Safety—Rigid Washer Extractors
WARNING 2 : Entangle and Crush Hazards—Contact with moving components normally isolated by guards, covers, and panels, can entangle and crush your limbs. These components move automatically.
•Do not remove guards, covers, or panels.
•Do not reach into the machine housing or frame.
•Keep yourself and others off of machine.
•Know the location of all emergency stop switches, pull cords, and/or kick plates and use them in an emergency to stop machine motion.
3.Safety Alert Messages—Cylinder and Processing Hazards
[Document BIUUUS13]
The following are instructions about hazards related to the cylinder and laundering process.
DANGER 3 : Entangle and Sever Hazards—Contact with goods being processed can cause the goods to wrap around your body or limbs and dismember you. The goods are normally isolated by the locked cylinder door.
•Do not attempt to open the door or reach into the cylinder until the cylinder is stopped.
•Do not touch goods inside or hanging partially outside the turning cylinder.
•Do not operate the machine with a malfunctioning door interlock.
•Know the location of all emergency stop switches, pull cords, and/or kick plates and use them in an emergency to stop machine motion.
•Know the location of the main machine disconnect and use it in an emergency to remove all electric power from the machine.
WARNING 4 : Crush Hazards—Contact with the turning cylinder can crush your limbs. The cylinder will repel any object you try to stop it with, possibly causing the object to strike or stab you. The turning cylinder is normally isolated by the locked cylinder door.
•Do not attempt to open the door or reach into the cylinder until the cylinder is stopped.
•Do not place any object in the turning cylinder.
•Do not operate the machine with a malfunctioning door interlock.
WARNING 5 : Confined Space Hazards—Confinement in the cylinder can kill or injure you. Hazards include but are not limited to panic, burns, poisoning, suffocation, heat prostration, biological contamination, electrocution, and crushing.
• Do not attempt unauthorized servicing, repairs, or modification.
WARNING 6 : Explosion and Fire Hazards—Flammable substances can explode or ignite in the cylinder, drain trough, or sewer. The machine is designed for washing with water, not any other solvent. Processing can cause solvent-containing goods to give off flammable vapors.
•Do not use flammable solvents in processing.
•Do not process goods containing flammable substances. Consult with your local fire department/public safety office and all insurance providers.
PELLERIN MILNOR CORPORATION
5
Safety—Rigid Washer Extractors
4.Safety Alert Messages—Unsafe Conditions [Document BIUUUS14]
4.1.Damage and Malfunction Hazards
4.1.1.Hazards Resulting from Inoperative Safety Devices
DANGER 7 : Entangle and Sever Hazards—Cylinder door interlock—Operating the machine with a malfunctioning door interlock can permit opening the door when the cylinder is turning and/or starting the cycle with the door open, exposing the turning cylinder.
• Do not operate the machine with any evidence of damage or malfunction.
WARNING 8 : Multiple Hazards—Operating the machine with an inoperative safety device can kill or injure personnel, damage or destroy the machine, damage property, and/or void the warranty.
•Do not tamper with or disable any safety device or operate the machine with a malfunctioning safety device. Request authorized service.
WARNING 9 : Electrocution and Electrical Burn Hazards—Electric box doors— Operating the machine with any electric box door unlocked can expose high voltage conductors inside the box.
• Do not unlock or open electric box doors.
WARNING 10 : Entangle and Crush Hazards—Guards, covers, and panels—Operating the machine with any guard, cover, or panel removed exposes moving components.
•Do not remove guards, covers, or panels.
4.1.2.Hazards Resulting from Damaged Mechanical Devices
WARNING 11 : Multiple Hazards—Operating a damaged machine can kill or injure personnel, further damage or destroy the machine, damage property, and/or void the warranty.
•Do not operate a damaged or malfunctioning machine. Request authorized service.
WARNING 12 : Explosion Hazards—Cylinder—A damaged cylinder can rip apart during extraction, puncturing the shell and discharging metal fragments at high speed.
• Do not operate the machine with any evidence of damage or malfunction.
WARNING 13 : Explosion Hazards—Clutch and speed switch (multiple motor machines)—A damaged clutch or speed switch can permit the low speed motor to engage during extract. This will over-speed the motor and pulleys and can cause them to rip apart, discharging metal fragments at high speed.
•Stop the machine immediately if any of these conditions occur: • abnormal whining sound during extract • skidding sound as extract ends • clutches remain engaged or re-engage during extract
PELLERIN MILNOR CORPORATION
6
Safety—Rigid Washer Extractors
4.2. Careless Use Hazards
4.2.1.Careless Operation Hazards—Vital Information for Operator Personnel (see also operator hazards throughout manual)
WARNING 14 : Multiple Hazards—Careless operator actions can kill or injure personnel, damage or destroy the machine, damage property, and/or void the warranty.
•Do not tamper with or disable any safety device or operate the machine with a malfunctioning safety device. Request authorized service.
•Do not operate a damaged or malfunctioning machine. Request authorized service.
•Do not attempt unauthorized servicing, repairs, or modification.
•Do not use the machine in any manner contrary to the factory instructions.
•Use the machine only for its customary and intended purpose.
•Understand the consequences of operating manually.
4.2.2.Careless Servicing Hazards—Vital Information for Service Personnel (see also service hazards throughout manuals)
WARNING 15 : Electrocution and Electrical Burn Hazards—Contact with electric power can kill or seriously injure you. Electric power is present inside the cabinetry unless the main machine power disconnect is off.
•Do not service the machine unless qualified and authorized. You must clearly understand the hazards and how to avoid them.
•Abide by the current OSHA lockout/tagout standard when lockout/tagout is called for in the service instructions. Outside the USA, abide by the OSHA standard in the absence of any other overriding standard.
WARNING 16 : Entangle and Crush Hazards—Contact with moving components normally isolated by guards, covers, and panels, can entangle and crush your limbs. These components move automatically.
•Do not service the machine unless qualified and authorized. You must clearly understand the hazards and how to avoid them.
•Abide by the current OSHA lockout/tagout standard when lockout/tagout is called for in the service instructions. Outside the USA, abide by the OSHA standard in the absence of any other overriding standard.
WARNING 17 : Confined Space Hazards—Confinement in the cylinder can kill or injure you. Hazards include but are not limited to panic, burns, poisoning, suffocation, heat prostration, biological contamination, electrocution, and crushing.
•Do not enter the cylinder until it has been thoroughly purged, flushed, drained, cooled, and immobilized.
—End of BIUUUS27 —
PELLERIN MILNOR CORPORATION
7
BIWUUI02 (Published) Book specsDates: 20001108 / 20001108 / 20100609 Lang: ENG01 Applic: WUU
About the Forces Transmitted by Milnor® Washer-extractors
During washing and extracting, all washer-extractors transmit both static and dynamic (cyclic) forces to the floor, foundation, or any other supporting structure. During washing, the impact of the goods as they drop imparts forces which are quite difficult to quantify. Size for size, both rigid and flexibly-mounted machines transmit approximately the same forces during washing. During extracting, rigid machines transmit forces up to 30 times greater than equivalent flexiblymounted models. The actual magnitude of these forces vary according to several factors:
•machine size,
•final extraction speed,
•amount, condition, and type of goods being processed,
•the liquor level and chemical conditions in the b ath preceding extraction, and
•other miscellaneous factors.
Estimates of the maximum force normally encountered are available for each Milnor® model and size upon request. Floor or foundation sizes shown on any Milnor® document are only for ongrade situations based only on previous experience without implying any warranty, obligation, or responsibility on our part.
1. Rigid Machines
Size for size, rigid washer-extractors naturally require a stronger, more rigid floor, foundation, or other supporting structure than flexibly-mounted models. If the supporting soil under the slab is itself strong and rigid enough and has not subsided to leave the floor slab suspended without support, on grade installations can often be made directly to an existing floor slab if it has enough strength and rigidity to safely withstand our published forces without transmitting undue vibration. If the subsoil has subsided, or if the floor slab itself has insufficient strength and rigidity, a deeper foundation, poured as to become monolithic with the floor slab, may be required. Support pilings may even be required if the subsoil itself is “springy” (i.e., if its
resonant frequency is near the operating speed of the machine). Above-grade installations of rigid machines also require a sufficiently strong and rigid floor or other supporting structure as described below.
2. Flexibly-mounted Machines
Size for size, flexibly-mounted machines generally do not require as strong a floor, foundation, or other supporting structure as do rigid machines. However, a floor or other supporting structure having sufficient strength and rigidity, as described in Section 3, is nonetheless vitally important for these models as well.
3. How Strong and Rigid?
Many building codes in the U.S.A. specify that laundry floors must have a minimum live load capacity of 150 pounds per square foot (732 kilograms per square meter). However, even compliance with this or any other standard does not necessarily guarantee sufficient rigidity. In any event, it is the sole responsibility of the owner/user to assure that the floor and/or any other supporting structure exceeds not only all applicable building codes, but also that the floor and/or any other supporting structure for each washer-extractor or group of washer-extractors actually has sufficient strength and rigidity, plus a reasonable factor of safety for both, to support the weight of all the fully loaded machine(s) including the weight of the water and goods, and including the published 360º rotating sinusoidal RMS forces that are transmitted by the machine(s). Moreover, the floor, foundation, or other supporting structure must have sufficient
PELLERIN MILNOR CORPORATION
8
About the Forces Transmitted by Milnor®Washer-extractors
rigidity (i.e., a natural or resonant frequency many times greater than the machine speed with a reasonable factor of safety); otherwise, the mentioned 360º rotating sinusoidal RMS forces can be multiplied and magnified many times. It is especially important to consider all potential vibration problems that might occur due to all possible combinations of forcing frequencies (rotating speeds) of the machine(s) compared to the natural frequencies of the floor and/or any other supporting structure(s). A qualified soil and/or structural engineer must be engaged for this purpose.
Figure 1: How Rotating Forces Act on the Foundation
Typical Machine
Legend
A.Direction of force
B.Load
C.Rotation (Frequency = RPM / 60)
Figure 1 above is intended to depict both on-grade and above-grade installations and is equally applicable to flexibly-mounted washer-extractors, as well as to rigid models installed either directly on a floor slab or on a foundation poured integrally with the slab. Current machine data is available from Milnor® upon request. All data is subject to change without notice and may have changed since last printed. It is the sole responsibility of every potential owner to obtain written confirmation that any data furnished by Milnor® applies for the model(s) and serial number(s) of the specific machines.
— End of BIWUUI02 —
PELLERIN MILNOR CORPORATION
9
BIUUUI02RC (Published) Book specsDates: 20110131 / 20110131 / 20110131 Lang: ENG01 Applic: RMC
Understanding the Tag Guidelines for the Models Listed Below
30010CGE 30015C4A 30015C4E 30015C4T 30015CGE 30022C4A 30022C4E 30022C4T
Several installation guidelines and precautions are displayed symbolically, on tags placed at the appropriate locations on the machine. Some are tie-on and others are adhesive tags. Tie-on tags and white, adhesive tags may be removed after installation. Yellow adhesive tags must remain on the machine.
PELLERIN MILNOR CORPORATION
10
Understanding the Tag Guidelines for the Models Listed Below
Most tags contain only symbols (no words). A few are worded. The explanations below, start with the tag part number (displayed on the tag). If a tag contains no words, the meaning of the tag is explained below. If the tag contains words, the explanation below simply repeats the wording.
Display or Action |
Explanation |
|
Read the manual before proceeding. This symbol appears on |
|
most tags. The machine ships with a complete set of manuals. |
|
The safety, installation, and electrical schematic manuals are |
|
particularly important to installers. |
|
B2TAG88005: This carefully built product was tested and |
|
inspected to meet Milnor performance and quality standards by |
B2TAG93013: This bearing housing was lubricated at the
Milnor factory before shipment.
B2TAG94081: Motor must rotate in this direction. On single motor washer-extractors and centrifugal extractors, the drive motor must turn in this direction during draining and extraction. This tag is usually wrapped around a motor housing. If the motor turns in the opposite direction when the machine is first tested, the electrical hookup is incorrect and must be reversed as explained in the schematic manual.
B2TAG94097: The cylinder must rotate counterclockwise during draining and extraction (spin) when viewed from here (rear of machine). Otherwise, reverse the electric power connections, as explained in the schematic manual.
B2TAG94099: Do not strike the shell door when fork-lifting.
This can cause the door to leak.
B2T2001013: Hot water connection.
PELLERIN MILNOR CORPORATION
11
Display or Action |
Explanation |
|
B2T2001014: Cold water connection. |
B2T2001016: Flushing water connection. This is the water that goes into the supply compartment or pumped chemical manifold to flush chemicals into the machine.
B2T2003001: Hold the side of the connection stationary with a wrench as you tighten the connection with another wrench. Otherwise, you may twist components, such as valves, damaging them.
B2T2003002: CAUTION: Equipment and Textile Damage Hazards—Chemicals leaked into the machine, particul arly when it is idle, can destroy machine components and textiles left in the machine.
Ensure the chemical system prevents dribbling, siphoning, or any other unintentional release of chemicals.
Inspect regularly for proper operation and evidence of damage. Consult Milnor document BIWUUI03 “Avoiding Damage f rom Allied Remote Chemical Delivery Systems”.
— End of BIUUUI02 —
PELLERIN MILNOR CORPORATION
12
Loading...