Pre-finished
30” MasterCool II
K 2801 SF* / K 2811 SF*
F 2801 SF* / F 2811 SF*
KF 2801 SF / KF 2811 SF
Shown: F 2471 SF merged with K 2801 SF
Please note: This information is subject to
*The following models are not available in Canada: K 2801 SF, K 2811 SF, F 2801 SF & F 2811 SF
change
Specification Sheets TRS 04252019
8miele.ca
Pre-finished
30” MasterCool II
SPECIFICATIONS
Overall Unit Dimensions 293/4” (756 mm) W x 833/4”- 853/16” (2127 - 2164 mm) H x 24” (610 mm) D [Excludes Fascia Dimension]
Overall Fascia Dimensions 301/2” (775 mm) W x 84”- 8511/16” (2134 - 2175 mm) H x 11/2” (32 mm) D
Niche
Minimum Cabinet Niche Opening 30” (762 mm) W* x 84” - 853/16” (2134 - 2164 mm) H x 24” (610 mm) D
Interior Volume K 28x1 SF F 28x1 SF KF 28x1 SF
Refrigeration Volume ** 0 **
Freezer Volume 0 ** *
Electrical
Electrical Requirements
Power Cord NEMA 5-15 plug, 5 ft (1.52 m)
Plumbing K 28x1 SF F 28x1 SF KF 28x1 SF
Water Supply Requirements -
K 28x1 SF F 28x1 SF KF 28x1 SF
110V / 120V, 60Hz, 15 Amps
In the case of side-by-side installations, a separate outlet must be used for each appliance.
Connect to a cold water supply only. Do not connect to a low-mineral or
a reverse osmosis system. Must be connected to a shut-off valve. The
water shut-off valve must be accessible after installation. The water pressure must be between 29 psi (2 bar) and 116 psi (8 bar). If the pressure is
higher than 120 psi (8.3 bar), a pressure reducing valve must be installed.
Water Connection Line
Shipping
Shipping Weight 453 lbs (205.5 kg) 462 lbs (210 kg) 485 lbs (220 kg)
Shipping Dimensions 297/8” (759 mm) W x 841/4” (1,240 mm) H x 297/8” (759 mm) D
Support
Call Miele
Miele Website
20/20 Link
Please note the following:
• This specication sheet is for a single built-in unit.
• When combining multiple MasterCool units side-by-side, please refer to the Merging Kit specication sheet.
*If design calls for a partition less than 6 5/16” (160 mm) the left unit’s cutout will require an additional 1/8” (3 mm) to the width to allow installation of
the Heating Mat/Merge Kit.
-
K 28x1 SF F 28x1 SF KF 28x1 SF
Standard 1/4” O.D flexible water line. The maximum outer diameter of the
water pipe (without fittings): 3/8” (10 mm). Water line is not included.
(800) 565-6435
8www.miele.ca
82020technologies.com
K 2801 SF (Right Hinged)
K 2811 SF (Left Hinged)
F 2801 SF (Right Hinged)
F 2811 SF (Left Hinged)
KF 2801 SF (Right Hinged)
KF 2811 SF (Left Hinged)
Page 2 of 6
CUTOUT DIMENSIONS
Please note unit’s outer SF frame.
Top view:
Niche/Cabinetry
3/4”
(19)
9/32”
(7)
Pre-finished
30” MasterCool II
Stainless steel door
SF frame
CUTOUT DETAILS
• The electrical connection must not be positioned higher
than 9” (228.6 mm) above the oor.
• The 1/4” (6.4 mm) plumbed water connection should
not be positioned higher than 2” (50.8 mm) above the
oor.
Notes:
In case of an emergency the electrical outlet must be
easily accessible and must not be concealed behind the
appliance.
Page 3 of 6
Pre-finished
30” MasterCool II
POWER SUPPLY AND WATER CONNECTION
(Water Connection For F 28x1 SF & KF 28x1 SF Only)
Rear View Front View
Electrical - 5 foot (1.52 m) - 120 Volt - 15 Amp
- NEMA 5-15 molded plug
Water line - 1/4” exible water line - not included
Side View
Water connection is located in front of unit.
1/4” compression tting is needed.
Electrical
Connection
Page 4 of 6
HINGING DETAILS 115° OPENING
Available for the following models:
• K 28x1 SF
• F 28x1 SF
• KF 28x1 SF
1-1/4” (32 mm)
1-1/2” (38 mm)
1-3/4” (44 mm)
0-3/4” (19 mm)
1” (25 mm)
30” MasterCool II
0-3/4” (19 mm)
Pre-finished
1/4”(6.4mm)
1/4”(6.4mm)
2-5/8”
(67mm)
2-5/8”
(67mm)
2-1/3” (59mm)
2-1/3” (59mm)
2-1/24”(52mm)
2-1/24”(52mm)
1-3/8”(35mm)
1-3/8”(35mm)
1-1/6”
1-1/6”
17/24” (18mm)
17/24” (18mm)
(29.6mm)
(29.6mm)
1-3/4”(44.5mm)
1-3/4”(44.5mm)
3”(76.2mm)
3”(76.2mm)
0-1/8” (3 mm)
DOOR SWING AT 115° OPENING
1-1/4” (32 mm)
1-1/2” (38 mm)
11 3/4”
(298 mm)
Max
1” (25 mm)
Page 5 of 6
HINGING DETAILS 90° OPENING
Available for the following models:
• K 28x1 SF
• KF 28x1 SF
1-1/4” (32 mm)
1-3/4” (44 mm)
1-1/2” (38 mm)
2” (51 mm)
0-3/4” (19 mm)
1” (25 mm)
Pre-finished
30” MasterCool II
7/16”
(11 mm)
1-3/16”
(30mm)
1-7/16”
(36.5mm)
1-11/16”
(43mm)
1-15/16”
(49.2mm)
0-1/8” (3 mm)
Handle or object that is
NOT ush with Cabinet
Front.
DOOR SWING AT 90° OPENING
0-3/4” (19 mm)
1” (25 mm)
1-1/4” (32 mm)
1-1/2” (38 mm)
7/16” (11 mm)
/16” (830 mm)
11
32
When installing hinge side next to an appliance or object that is within range of the door panel,
limit the door opening angle to 90°. This is done by installing the banking pin as illustrated.
Insert the banking pin through the holes and drive in with a hammer.
Specification Sheets TRS 04252019
Page 6 of 6
Loading...