Maytag MAT14PDAWW0, MAT14CSAGW0, MAT14CSAWW0 Installation Guide
I _AY£AG ®
COMMERCIAL WASHER
INSTALLATION INSTRUCTIONS
120-volt, 60-Hz Models
INSTRUCTIONS D'INSTALLATION DE
LA LAVEUSE COMMERCIALE
ModUles 120 V, 60 Hz
Write down the model and serial numbers before installing washer.
Both numbers are listed on the model/serial rating plate located
under the lid.
Model #
Serial #
Date of Purchase
Prendre note des numeros de modele et de serie avant d'installer
la laveuse.
Les deux numeros sont indiques sur la plaque signaletique sous
le couvercle.
Numero de modele
Numero de serie
Date d'achat
W10135283A
www.maytagcommerciallaundry.com
Table of Contents
WASHER SAFETY ........................................................................ 2
INSTALLATION REQUIREMENTS .............................................. 3
Tools and Parts .......................................................................... 3
Location Requirements .............................................................. 3
Drain System .............................................................................. 4
Electrical Requirements ............................................................ 5
INSTALLATION INSTRUCTIONS ............................................ 6
Remove Shipping Strap ............................................................ 6
Connect the Hoses .................................................................... 6
Level the Washer ...................................................................... 7
Complete Installation ................................................................ 8
Additional Features .................................................................... 8
Tabledes mati res
S¢CURIT¢: DE LA LAVEUSE .................................................... 11
EXIGENCES D'INSTALLATION ................................................ 12
Outillage et pieces .................................................................. 12
Exigences d'emplacement ...................................................... 12
Systeme de vidange ................................................................ 13
Specifications electriques ........................................................ 14
INSTRUCTIONS B'INSTALLATION ........................................ 15
Enlever la sangle d'expedition ................................................ 15
Raccordement des tuyaux ...................................................... 15
Reglage de I'aplomb de la laveuse ........................................ 16
Achever I'installation ................................................................ 17
Caracteristiques supplementaires .......................................... 17
WASHERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
, follow instructions.
, instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,
including the following:
• Read all instructions before using the washer. •
• Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive •
substances as they give off vapors that could ignite or
explode. •
• Do not add gasoline, dry-cleaning solvents, or other
flammable, or explosive substances to the wash water. •
These substances give off vapors that could ignite or
explode.
• Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used •
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water •
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
this time.
SAVE THESE INSTRUCTIONS
INSTALLATIONREQUIREMENTS
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
Before the washer is removed from service or discarded,
remove the door or lid.
Do not reach into the washer if the drum, tub or agitator is
moving.
Do not install or store the washer where it will be exposed to
the weather.
Do not tamper with controls.
Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and
have the skills to carry out.
See "Electrical Requirements" for grounding instructions.
Gather the required tools and parts before starting installation.
Tools needed
• Level
• Utility knife
• Scissors
• 8" or 10" adjustable wrench
• Flat-blade screwdriver
• Pliers
• Bucket
Parts supplied
Remove parts bag from washer. Check that all parts were
included.
• 1 hose clamp
• 2 inlet hoses
• 4 flat water hose washers
• 2 front-leveling legs with nuts
• 1 drain hose
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather. Do not store or operate the washer in
temperatures at or below 32°F (0°C). Some water can remain in
the washer and can cause damage in low temperatures.
Proper installation is your responsibility.
You will need:
• A water heater set to deliver 120°F (49°C) water to the washer.
• A grounded electrical outlet located within 4 ft (1.2 m) of where
the power cord is attached to the back of the washer.
See "Electrical Requirements."
• Hot and cold water faucets located within 4 ft (1.2 m) of the
back of the washer, and provide water pressure of 10-100 psi
(69-690 kPa). A pressure reduction valve should be used in
the supply line where inlet pressure entering the building
exceeds 100 psi (690 kPa) to prevent damage to the washer
mixing valve.
• A level floor with a maximum slope of 1" (2.5 cm) under entire
washer.
• A sturdy floor to support the washer weight (washer, water
and load) of 315 Ibs (143 kgs).
• A 12" (30 cm) minimum riser to provide an air cushion and
prevent noise and damage to valves for a single washer
installation.
• A floor drain should be provided under the bulkhead.
Prefabricated bulkheads with electrical outlets, water supply
lines and drain facilities should be used only where local
codes permit.
NOTE: Front access to the pump area is available by removing
2 clips under the console area and removing the top and
cabinet assembly.
Recessed Area and Closet Installation Instructions
This washer may be installed in a recessed area or closet.
The installation spacing is in inches and is the minimum
allowable. Additional spacing should be considered for ease of
installation, servicing, and compliance with local codes and
ordinances.
If closet door is installed, the minimum unobstructed air openings
in the top and bottom are required. Louvered doors with
equivalent air openings are acceptable.
j closetdoor
Product Dimensions
oloo
17"
(43.2 cm)
3100m2 *U J xtCm
24,,2 -_F 4"
1"./2.5cm,
(Ocm) (Ocm)
rain.
Recessed front view Closet side view
3" (7.5 cm)
(310 cm=)*
Front view
48,2 _'
24,2
closet
0
door
(155cm2)*
3" (7.6cm)
i
*Opening is the minimum for a closet door.
Louvered doors with equivalent air openings are acceptable.
• Additional spacing should be considered for the ease of
installation and servicing.
• Additional clearances may be required for wall, door and floor
moldings.
• Additional spacing of 1" (2.5 cm) on all sides of the washer is
recommended to reduce noise transfer.
• Companion spacing should also be considered.
N
A. 43" (109 cm)
S. 38_" (97 cm)
C. 35" (89 cm)
D. 1½"(3.8cm)
E. 27¾" (70.5 cm)
fi 25 ½" (65 cm)
G. Water inlets
H. 7" (18 cm)
I. Power supply cord
J. Drain hose connector
K. Label
L. 27" (68.5 cm)
M. 5 ¼" (13.3 cm)
N. 1"(2.5cm)
O. Water level switch and shaft
R 5" (12.7 cm)
.......
Standpipe Drain System
The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute.
The top of the standpipe must be at least 39" (99 cm) high and
no higher than 72" (183 cm) from the bottom of the washer.
v _ _
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
IMPORTANT: The washer must be electrically grounded in
accordance with local codes and ordinances or, in the absence of
local codes, with the National Electrical Code, ANSl/NFPA 70,
latest edition.
• If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine
that the ground path is adequate.
• Do not ground to a gas pipe.
• Do not have a fuse in the neutral or ground circuit.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park, Quincy, MA 02269
• A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical
circuit is required. A time-delay fuse or circuit breaker is
recommended. It is recommended that a separate circuit
serving only this washer be provided.
• The washer is equipped with a power supply cord having a
3 prong grounding plug.
• To minimize possible shock hazard, the cord must be plugged
into a mating, 3 prong, grounded-type outlet, grounded in
accordance with local codes and ordinances. If a mating
outlet is not available, it is the personal responsibility and
obligation of the customer to have the properly grounded
outlet installed by a qualified electrician.
Recommended Ground Method
The washer, when installed, must be electrically grounded in
accordance with local codes, or in the absence of local codes,
with the National Electrical Code, ANSI/NFPA 70, latest edition,
and all local codes and ordinances.
GROUNDING INSTRUCTIONS
For a grounded, cord=c_nnected washer:-
This washer must be grounded. In the event of a malfunction
or breakdown, grounding will reduce the risk of electrical
shock by providing a path of least resistance for electric
current. This washer is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordinances. _
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance - if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
For a permanently connected washer: _
This washer must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the appliance. _
INSTALLATIONINSTRUCTIONS
Proper connection of the drain hose protects your floors from
damage due to water leakage. Read and follow these
instructions.
Connect the inlet hoses to the washer
Remove tape that covers the shipping strap. Pull to
completely remove the shipping strap with 2 cotter pins from
the inside of the washer.
A.Shippingtape
B.Shippingstrap
2=
Pull firmly to remove the end of shipping strap from the back
of the washer. The shipping strap plug must be completely
removed from the washer for the self-leveling legs to be
released.
The washer must be connected to the water faucets using
the new inlet hoses. Do not use old hoses. Insert new flat
washers (supplied) into each end of the inlet hoses. Firmly
seat the washers in the couplings.
A B
A. Coupling
B. Washer
2. Attach hose to bottom inlet valve opening first.
Save the shipping strap for later use.
A. Cold water inlet valve
B. Hot water inlet valve
3. Attach second hose to top inlet. Tighten couplings by hand;
then use pliers to make an additional two-thirds turn.
NOTE: Inlet valve threads are plastic. Do not strip or cross-
thread.
Loading...