M-AUDIO CX8 User Manual

Studiophile™

CX8

English

User Guide

!!!

CAUTION ATTENTION:

PRECAUCION:

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

N’OUVRIR PAS

RIESGO DE ELECTROCHOQUE

NO ABRIR LA TAPA

CAUTION: TO REDUCE THE RISK OF

!

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER­SERVICABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE

PERSONNEL

AFIN DEVITER UN CHOC

ELECTRIQUE ET LES

CONSEQUENCES GRAVES QUI

POURRAIENT ENRESULTER, TENTEZ

PAS D’OUVRIR L’APPAREIL ET DE

TOUCHER AUX COMPOSANTS

INTERNES SANS LA PRESENCE

D’UNE PERSONNE QUALIFIEE.

PARA REDUCIREL RIESGO DE
SACUDIDAS ELECTRICAS, NO

DEBERA QUITARSE LA TAPA

(NI PARTE POSTERIOR).

CONSULTESE AL PERSONAL

CAPACITADO PARA LAS

REPARACIONES INTERNAS.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.

ADVERTENICIA: PARA EVITAR EL RIESGO DE INCENDIO O SACUDIDA ELECTRICA, NO DEBERA
EXPONERSE ESTE APARATO A LA LLUVIA O HUMEDAD.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.

ATTENTION: POUR PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE
POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE
COURANT, SAUF SILES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE
PARTIE FOND SANS EN LAISSERAUCUNE PARTIE A DECOUVERT.

PRECAUCION: PARA EVITAR SACUDIDAS ELECTRICAS, NO DEBERA UTILIZARSE ESTA CLAVIJA
POLARIZADA CON UN CORDON DE PROLONGACION, RECEPTACULO U OTRO TIPO DE SALIDA
A MENOS QUE SE HAYAN INSERTASO COMPLETAMENTE LAS LENGÜETAS PARA EVITAR SU
EXPOSICION.

NOTE: Some products are equipped with dual or multi-voltage transformers (which is indicated on the back
panel). If you wish to change the voltage, please bring your unit to an authorized service technician for
internal conversion.

ATTENTION: Quelques piéces sont munies de transformateurs á double ou á multi-voltage (indiqué au
panneau arriére). Si vous voulez changer le voltage, veuillez apporter votre appareil au fournisseur de pour
le transformer.

ZUR BEACHTUNG: Einige Geräte sind mit Umschaltern für unterschiedliche Netzspannungen ausgerüstet
(ein Vermerk auf der Rückseite weist darauf hin).

Die Anpassung, wenn notwendig, muß von einem qualizieren Techniker in einer Servicestation

vorgenommen werden.

NOTA: Ciertos componentes de están dotados de transformadores de doble tensión o de varias tensiones (Io
que se indica en el panel posterior). Si se desea cambiar la tensión, sírvanse llevar el aparato a un técnico
autorizado por para su conversión interna.

NOTE TO CATV SYSTEMS INSTALLER: This reminder is provided to call the CATV system installer’s
attention to Article 820-22 of the NEC that provides guidelines for proper grounding and, in particular,

species that the cable ground shall be connected to the grounding system of the building, as close to the

point of cable entry as practical.

NOTA PARA EL INSTALADOR DE ANTENAS DE TELEVISION COLECTIVAS: La presente advertencia se
provee para llamar la atención del instalador al Artículo 820-22 de NEC (Córdigo Eléctrico Nacional) donde

se facilitan las directrices para la pertinente puesta a tierra y que especica en particular que el condutor a
tierra del cable debe connectarse al sistema de conexión a tierra del edicio, lo más proximo posible al punto

de entrada del cable.

The lightning ash with arrowhead, within an

equilateral triangle, is intended to alert the user of

the presence of uninsulated “dangerous voltage”

within the product’s enclosure; that may be of

sufcient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral triangle

is intended to alert the user of the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

Warning: This speaker shall not be placed in a closed area during operation so that the main switch can be
easily accessed by the user.

IMPORTANT SAFETY INSTRUCTION

1. READ INSTRUCTIONS

All the safety and operating instructions should

be read before the appliance is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be

retained for future reference.

3. HEED WARNINGS

All warning on the appliance and in the operating

instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be

followed.

5. WATER AND MOISTURE

The appliance should not be used near water –

for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a
swimming pool, etc.

6. CARTS AND STANDS

The appliance should be used only with a cart or

stand that is recommended by the manufacturer.

6A. An appliance and cart combination should be moved

with care. Quick stops, excessive force, and uneven
sTurfaces may cause the appliance and cart
combination to overturn.

7. WALL OR CEILING MOUNTING

This equipment is not designed

for use mounted on a wall or a
ceiling.

8. VENTILATION

The appliance should be situated so that its

location or position does not interfere with its
proper ventilation. For example, the appliance
should not be situated on a bed, sofa, rug, or
similar surface that may block the ventilation
openings, or places in a built-in installation, such

as bookcase or cabinet that may impede the ow

of air through the ventilation openings.

At least 30 cm free space around the unit for

normal ventilation is required.

9. HEAT

Do not install near any heat sources such

as radiators, heat registers, stoves, or other

apparatus (including ampliers) that produce

heat.

10. CLEANING

The appliance should be cleaned only with dry

cloth.

11. POWER SOURCES

The appliance should be connected to a power

supply only of the type described in the operating
instructions or as marked on the appliance.

12. POWER CORD PROTECTION

Power-supply cord should be routed so that they

are not likely to be walked on or pinched by items
placed upon or against them, playing particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the appliance.

13. POLARIZED PLUG

Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a
third grounding prong. The wide blade or the
third prong are provided for your safety. When

the provided plug does not t into your outlet,

consult an electrician for replacement of the
obsolete outlet.

14. UNPLUG POWER CORD

Unplug this apparatus during lightning storms or

when unused for long periods of time.

15. OBJECT AND LIQUID ENTRY

No object lled with liquids, such as vases, etc.

shall be placed on the apparatus.

16. ACCESSORIES

Only use attachments/accessories specied by

the manufacturer.

17. SERVICING

The user should not attempt to service the

appliance beyond that described in the operating
instructions. All other servicing should be referred

to qualied service personnel.

18. DAMAGE REQUIRING SERVICE

The appliance should be serviced by qualied

service personnel when:

a) The power-supply cord or the plug has been

damaged; or

b) Objects have fallen, or liquid has been spilled

into the appliance; or

c) The appliance has been exposed to rain; or

d) The appliance does not appear to operate

normally or exhibits a marked change in
performance; or

e) The appliance has been dropped, or the

enclosure is damaged.

4

English

1. Introduction

Thank you for choosing the M-Audio CX8 bi-amplified studio monitors. The CX line of
loudspeakers build on M-Audio’s legacy of high performance studio monitors and provide
accurate, high-resolution playback that is free of audible distortion and coloration. This
allows you to hear everything that is in your source recordings so that you can create better
mixes.

Even if you are experienced with recording and mixing, please take a moment to read
through this guide. It will give you valuable information about how to set up your CX
monitors and will help you get the most out of your new purchase.

2. What’s in the Box?

This package contains:

 CX8 studio monitor (1)

 IEC power cable (1)

 This User Guide

3. About CX Studio Monitors

Typical mass-market loudspeakers sound pleasing because their designs incorporate a
deliberately uneven, non-linear frequency response that artificially enhances certain bass
and treble frequencies. While it may be quite enjoyable to hear finished albums on such
speakers, actually mixing on this type of monitor is not recommended since such speakers
tend to “smooth over” problem areas and do not reveal everything that should be fixed
during a mix.

Unlike typical mass-market speakers, M-Audio’s CX line of bi-amplified studio monitors
have been designed to provide accurate, highly detailed, reliable playback that is free of
distortion or coloration. This is done by having a tightly integrated system in which the CX
drivers, internal electronics (amplifiers, crossover, etc.), and enclosure all work together
to provide accurate bass, smooth high-frequency transient response, and a highly linear
frequency response through the entire audible range of the speaker. This allows you to
hear everything in your recorded tracks—the good and the bad things—so that you can spot
and fix problems and ultimately create great mixes that “translate” well to other speakers
and audio playback systems.

5

English

StudiophileTM CX8 User Guide

Note that the placement and

orientation of the CX monitors

within your studio is important

and correctly placed speakers will

result in improved imaging, clarity,

and overall performance. This

topic is covered in detail in the

“Setting up CX Monitors” section

of this guide.

Also note that the CX monitors

feature several switches that

help you contour the speaker

to your specific studio. When

*About anechoic chambers:

An anechoic chamber is a room in which the
floor, ceiling, and all walls are covered with
sound-absorbent acoustical wedges. These
wedges prevent sounds created within the room
from reflecting back and influencing the acoustic
measurement of the loudspeaker.

Anechoic chambers are considered to be
acoustically “neutral” spaces since the room itself
does not impart any kind of sound to an acoustical
source contained within the room. Because of
this, loudspeakers (including CX monitors) are
commonly measured and tuned in such rooms.

these switches are left in

their default position, the CX

monitor will closely resemble the response characteristics shown in the acoustic

frequency response graph in the appendix. These anechoic* measurements represent

performance of the speaker in an “ideal” environment similar to that found in a

high-end recording studio with carefully tuned acoustics. In the real world, however, the

acoustics of your specific studio (or the placement of your speakers within the studio)

may cause your monitors to exhibit too little (or too much) bass, midrange, or treble.

To help compensate for this, the rear-panel switches contour the frequency response

of the speaker specifically to your studio. These switches are covered in detail in the

“About the Rear-Panel EQ Contour Switches” section of this guide.

It’s in the details:

Did you know the shape and materials of a speaker cabinet can greatly affect the overall
sound of a speaker?

Your CX monitors feature thick walls and a carefully placed internal brace to prevent the
speaker from resonating at low frequencies. This means that the speaker cabinet itself will
not ring along with the low frequency sounds in your mix (such as a kick drum or a bass).
This translates into more accurate bass response.

Furthermore, the rounded (“radiused”) edges and contoured waveguide surrounding the
tweeter are not just cosmetic touches intended to improve the appearance of the speaker.
These features help spread high frequencies evenly around the room and widen the “sweet
spot” between the two speakers.

6

4. Product Features & Specifications

CX8

8” woofer with 1½” voice coil
Waveguide loaded silk-dome tweeter with 1¼” voice coil
Bi-amplified class A/B amplifiers
80W woofer
40W tweeter
Frequency response: 38Hz to 30kHz (+/- 3dB)

XLR, 1/4” TRS, and RCA inputs

Magnetically shielded for placement near CRT (tube-based) monitors and
televisions

Rear panel contour switches to optimize placement within any studio
Sturdy, acoustically inert 1” front and rear MDF baffles to prevent cabinet

resonances
Flared rear firing port for audibly increased system headroom
Optimized internal bracing to minimize sonic “coloration” caused by the cabinet
Radiused (rounded) cabinet edges and acoustical waveguide for even high-

frequency dispersion
Speaker protection:

• Output current limiting

• Over-temperature

• Transient on/off protection to prevent speaker “pops”

• Subsonic lter

• External mains fuse

7

English

StudiophileTM CX8 User Guide

2

10

5

1

6

4

3

9 8 7

5. Hardware Controls and Indicators

Rear Panel

1

Input Gain Knob: This knob adjusts the

gain level of the XLR/TRS

3

and RCA
inputs. The gain is at minimum when the
knob is turned fully counter-clockwise; the
gain is set to its maximum level when the
knob is turned fully clockwise.

2

RCA Input (-10dBV): This connector

accepts line-level signals from audio sources
with unbalanced RCA-style outputs.

3

XLR/TRS Input (+4dBu): This “combo”

input jack accepts both XLR and 1/4”
TRS-type connectors. Connect your audio
interface, mixer, or other line-level audio
source to this jack.

▶ NOTE: The XLR/TRS and RCA inputs are summed (i.e., mixed together) before arriving

at the CX amplifier and it is possible to have two sound sources connected to a speaker
at the same time. However, it is recommended that you do not play audio through both
connectors simultaneously as this may overload the inputs and result in clipping (distortion)
at the inputs.

2

4

Power Switch: This switch powers your

CX monitors on and off.

5

Power Connector: This socket accepts a

standard IEC-type power cable.

6

Input Voltage Selector: This recessed

switch adjusts the input voltage from
100-120V or 220-240V and allows your
CX monitor to be used worldwide. Make
sure this switch is set correctly for your
country to prevent damage to the speaker.

TIP: Power outlets in North
America, Japan, and many parts
of South America usually supply
between 100V and 120V whereas
outlets in Europe and most of Africa
and Asia provide between 220V and
240V. If you are not sure about your
region, be sure to check your power
outlet’s rating and set the Input
Voltage selector before connecting
and switching on your CX monitors.

8

7

11

Acoustic Space Switch: This switch allows you to set a “shelf” EQ to tailor low

frequency response to your specific studio. See the section entitled “About the
Rear-Panel EQ Contour Switches” to learn more about this switch.

8

HF Trim Switch: This switch allows you to adjust the high-frequency response

of the speaker to your specific studio. See the section entitled “About the Rear­Panel EQ Contour Switches” to learn more about this switch.

9

MF Boost Switch: This switch allows you to contour the midrange response of

the speaker to your specific studio. See the section entitled “About the
Rear-Panel EQ Contour Switches” to learn more about this switch.

10

LF Cutoff Switch: This switch sets the low-frequency cutoff point of your CX

monitor. See the section entitled “About the Rear-Panel EQ Contour Switches”
to learn more about this switch.

Front Panel

11

Power LED: This blue LED illuminates when the monitor is receiving power and

the rear panel Power Switch

4

is in the “ON” position.

9

English

StudiophileTM CX8 User Guide

Audio Interface

(Balanced TRS to Balanced TRS

Mixer

(Balanced XLR to Balanced TRS)

Control Room Router

(Balanced TRS to Balanced XLR)

Preamplifier Processor

(Unbalanced RCA to Unbalanced RCA)

6. Connection Diagram

M-Audio CX monitors feature balanced XLR/TRS “Combo” and unbalanced RCA-type
analog inputs on the rear panel. Connect the outputs of your mixer, audio interface, or
other line-level device to these inputs.

Audio Interface

(Balanced TRS to Balanced TRS)

Control Room Router

(Balanced TRS to Balanced XLR)

Mixer

(Balanced XLR to Balanced TRS)

Preamplifier Processor

(Unbalanced RCA to Unbalanced RCA)

▶ NOTE: the XLR/TRS and RCA inputs are summed (i.e., mixed together) before arriving

at the CX amplifier and it is possible to have two sound sources connected to a speaker
at the same time. However, it is recommended that you do not play audio through
both connectors simultaneously as this may overload the inputs and result in clipping
(distortion) at the inputs.

TIP: If your mixer, interface, or other audio source features both XLR/TRS
and RCA-type outputs, use the XLR or TRS connectors instead of the RCA
connectors whenever possible. XLR and TRS cables incorporate a “balanced”
design that carries a signal over three conductors (“hot,” “cold,” and “ground”)
instead of two conductors as found in RCA cables (“hot,” and “ground”). This
results in lower noise, higher rejection of radio-frequency (RF) interference, and
better overall fidelity. If XLR/TRS jacks are unavailable, use RCA-style cables
but try to keep the cables as short as possible.

10

7. Setting up CX Monitors

Tweeters

Left Monitor Right Monito

r

The configuration and placement of your CX monitors
within your studio may affect the performance of the
speakers. Use the following tips to achieve the best
possible performance out of your CX monitors:

Speaker Placement

Place the CX monitors so that the two speakers
and the engineer form an equilateral triangle when
viewed from above. Angle the speakers slightly
inward so that the woofer and tweeter face the
engineer.

In general, it is recommended that CX monitors
be placed at least one foot away from the nearest
wall, ceiling, or any other large, flat surface (the reason
for this is covered in detail in the following chapter of this
guide). If practical considerations such as limited studio
space make this impossible, CX monitors include an
Acoustic Space Switch

7

to compensate for placement
near walls and corners. See the following chapter of this
guide to learn more about this switch.

Speaker Height

TIP: If possible, place your
CX monitors on speaker stands
instead of your desk top. Desks
tend to resonate sympathetically
at low frequencies and may
adversely affect the bass response
of your monitors. If speaker
stands are not possible due to
space restrictions and you notice
a buildup in bass, try placing
the monitors on “speaker pads”
to acoustically de-couple the
monitors from the desk.

Position the speakers so that they are parallel to the ground and that your ears are
between the midpoint of the woofer and the tweeter.

Speaker Orientation

If possible, place CX monitors in their upright position and
avoid laying the speakers on their sides. The CX woofer
and tweeter are vertically aligned and will provide the best
performance when the speakers are placed upright. Placing
them on their sides may create strong reflections from
nearby surfaces resulting in spectrally unbalanced sound.

If your CX monitors must be oriented horizontally due to
space or line-of-sight considerations, place the speakers so that their tweeters are on
the “inside” to improve imaging.

11

English

StudiophileTM CX8 User Guide

About the Rear-Panel EQ Contour Switches

These switches allow you to tailor
the EQ curve of your CX monitors
to complement the frequency
response of your studio.

Since studio monitors (including
the CX series) are designed to
have a flat frequency response, you may be wondering why these speakers include
additional EQ switches. These switches are included for three reasons:

1. Size, shape, and acoustical treatment of your specific studio:

CX monitors are tested and tuned in an anechoic chamber to be as linear (flat)

as possible. This means that leaving the switches set to their default settings will
closely resemble the printed acoustic frequency response graph (see Appendix)
when monitoring takes place in an “ideal” environment similar to those found in high­end recording studios. In these studios, acousticians carefully determine the size
and shape of the control room, placement of the studio monitors and large furniture,
construction materials of the walls and ceiling, as well as all acoustical treatments
that must be applied to various parts of the room. All this ensures that studio
monitors will sound as flat and accurate as possible at the “mixing position.”

In the real-world, however, most project and home-based studios are set up in

preexisting rooms where the size/shape of the room cannot be easily modified to
improve acoustics. This means that the design of the room itself may have adverse
effects on the frequency response of the monitors (i.e, sound reflections from flat
surfaces in the room may cause the monitors to not sound linear). For that reason,
the CX line features “corrective” EQ switches to compensate for adverse effects
that may be caused by your room.

2. Placement of the CX monitors within your studio:

The proximity of your CX monitors to the walls (and floors/ceilings) may adversely

affect the frequency response of what you hear at the mixing position. This is
because all speakers radiate low-frequency sounds in all directions—not just toward
the mixing position. If there are large, flat surfaces (such as walls or ceilings) within
one foot of the speaker, these surfaces act as low frequency “sound reflectors” that
return bass energy projected from the rear of the speaker back into the studio. This
can result in bass that sounds “tubby” and exaggerated.

12

3. Using a subwoofer:

If you plan to use a subwoofer with your CX monitors, you will need to filter out low

frequency sounds so that only the subwoofer plays low-frequency sounds (the CX
monitors will only play midrange and high-frequency sounds, in this scenario). This
needs to be done so that the subwoofer and CX monitors do not both play the same
low-frequency sounds, causing a greatly exaggerated bass response within your
studio.

The CX line of monitors address all three of these issues with the following switches:

Acoustic Space Switch

As stated earlier in this section, your CX

monitors should ideally be placed at least one
foot away from the nearest wall, ceiling, or
other large, flat surface. In the real-world, this
may be impractical due to space limitations
within your studio. For that reason, CX
monitors feature an Acoustic Space Switch.

7

TIP: Be sure to leave at least
3” of space between the rear of
the speaker and a wall to allow
the rear-firing port to “breathe”
properly. Placing the speaker
any closer than 3” may adversely
affect low-frequency response.

This switch compensates for placement near
walls by “shelving” (reducing) frequencies below 200 Hz. This switch should be set
as follows:

0dB This default setting should be used if the monitors are placed at least one

foot away from the nearest wall.

-2dB This setting reduces frequencies below 200 Hz by 2dB. Use this setting if

the speakers must be placed closer than one foot from the nearest wall.

-4dB This setting reduces frequencies below 200 Hz by 4dB. Use this setting if

the speakers must be placed within one foot of the corner of a room (i.e.,
the intersection of two walls).

13

English

StudiophileTM CX8 User Guide

HF Trim Switch

8

This control allows you to boost or attenuate (reduce) your CX monitors’ high

frequency response above 3kHz. This switch can be set in the following ways:

0dB This default setting leaves high-frequency signals unaffected (high

frequency sounds are neither boosted nor attenuated).

+2dB This setting boosts signals above 3kHz by 2dB.

-2dB This setting attenuates signals above 3kHz by 2dB.

To configure the HF Trim switch, begin by mixing a few songs with this switch set

to the default “0dB” position. If your mixes sound good in the studio and on other
speakers (car stereos, “multimedia” computer speakers, etc.), leave this switch in the
default position.

If your mixes sound good in the studio but they sound “dull” and lack high-frequency

“sparkle” on other playback systems, set this switch to “-2dB.” Alternatively, if your
mixes sound good in the studio but sound too “crispy” or “brittle” and contain too
much high-frequency content, set this switch to “+2dB.” Setting this switch to either
“+2dB” or “-2dB” allows the CX monitors to compensate for a mixing environment
that is either too “live” (i.e., too much high-frequency reflection from the walls and
other surfaces) or too “dead” (i.e., not enough high frequency sound is being
reflected around the room).

MF Boost Switch

9

This control engages a midrange boost from 1.5 KHz - 2.5 kHz with a 2 dB peak at

2 kHz. This switch can be set in the following ways:

Out This default setting allows incoming signals to bypass the midrange boost

circuitry (the midrange of a signal is not affected).

In This setting engages the midrange boost circuitry and creates a 2dB peak

at 2kHz with a 1 kHz bandwidth (i.e., signals between 1.5 kHz - 2.5 kHz
are boosted).

To configure the MF Boost switch, leave the switch set to the “out” position

and mix a few songs. If you notice your mixes sound good in the studio but the
midrange tends to be too prominent (e.g., the vocals/guitars are too loud) on
other speakers, set this switch to “in.” This will make the midrange of your CX
monitors slightly more pronounced in the studio and will result in more balanced
mixes since you will be less inclined to “push” the midrange of your mixes.

14

LF Cutoff Switch

10

This control allows you to engage a high-pass filter that removes low-frequency

sounds from the monitors. This switch can be set in the following ways:

Flat This default setting allows your

monitors to play their entire
frequency spectrum with no low­frequency filtering.

60Hz This setting engages a second-

TIP: Many subwoofers feature
a low-pass cutoff frequency of
80Hz. If you are not sure about
your subwoofer, use this setting
as a starting point.

order (12dB/octave) filter that rolls
off frequencies below 60Hz.

80Hz This setting engages a second-

order (12dB/octave) filter that rolls
off frequencies below 80Hz.

If you are using your CX monitors with a

subwoofer that does not have a built-in
crossover, set this switch as close as
possible to the low-pass cutoff frequency of
your subwoofer. The low-pass cutoff of the
subwoofer should be listed in the “technical

TIP: This switch can also be
engaged if you wish to hear what
your mixes would sound like on
speakers with smaller woofers
(such as those found in most
televisions).

specifications” section of the subwoofer’s
User Guide.

If your subwoofer has an internal crossover that sends high-frequency signals out

to your main monitors through a pair of outputs, leave the LF Cutoff Switch on
your CX monitors set to “Flat.”

15

English

StudiophileTM CX8 User Guide

8. Appendix A - Technical Specifications

Frequency response: 38Hz-30kHz (+/-3dB)

Crossover frequency: 2.7kHz

Low-frequency amplifier
power:

High-frequency
amplifier power:

LF cutoff Flat, 60Hz, and 80Hz

MF boost In/Out of 2dB centered at 2kHz

HF trim +2dB, 0dB, -2dB above 3kHz

Acoustic space 0dB, -2dB, and -4dB

Maximum
signal-to-noise
(dynamic range):

Polarity: positive signal at + input produce outward LF cone displacement

Input impedance: 20k ohms balanced,

Input sensitivity: 100 mV pink noise input produces 95 dBA output SPL at one meter with volume

Power: factory programmed for either 115V ~50/60Hz or 230V ~50/60Hz

Protection: RF interference, output current limiting, over temperature,

Cabinet: Front and rear baffle 1” MDF with ¾” MDF wrap. Black lacquer paint on enclosure

Size: 17” (H) x 11” (W) x 13” (D); 43.2cm x 28cm x 33cm

Weight: 30.42 lbs./unit; 13.8 kg

80 watts with 14 gauge wiring to this transducer

40 watts with 14 gauge wiring to this transducer

> 97 dB (typical A-weighted)

10k ohms unbalanced

control at maximum

turn-on/off transient, subsonic filter, external mains fuse

with soft touch black paint on curved front plate.

Above specifications subject to change without notice

16

CX8 - Frequency Response

20 Hz 50 100 200 5001K2K5K 10K 20K 30

K

dBSPL

65

70

75

80

85

90

95

100

105

17

English

StudiophileTM CX8 User Guide

9. Warranty

Warranty Terms

M-Audio warrants products to be free from defects in materials and workmanship,

under normal use and provided that the product is owned by the original, registered
user. Visit www.m-audio.com/warranty for terms and limitations applying to your
specific product.

Warranty Registration

Immediately registering your new M-Audio product entitles you to full warranty

coverage and helps M-Audio develop and manufacture the finest quality products
available. Register online at www.m-audio.com/register to receive FREE product
updates and for the chance to win M-Audio giveaways.

Documentation Feedback

At M-Audio, we’re always looking for ways to improve our documentation. If you have
comments, corrections, or suggestions regarding our documentation, email us at
[e-mail]

CX8

Tested to comply with
FCC standards

FOR HOME OR STUDIO USE

WARNING: This product contains chemicals, including lead, known to the State of
California to cause cancer, and birth defects or other reproductive harm. Wash hands

after handling.

© 2009 Avid Technology, Inc. All rights reserved. Product features, specifications, system
requirements and availability are subject to change without notice. Avid, M-Audio and
CX8 are either trademarks or registered trademarks of Avid Technology, Inc. All other
trademarks contained herein are the property of their respective owners.

M-Audio USA | Avid Technology • M-Audio | www.m-audio.com

5795 Martin Rd., Irwindale, CA 91706

Technical Support

Sales e-mail

web . . . . . . . www.m-audio.com/tech

tel (pro products) . . . . [phone]

. . . . . . . . [e-mail]

fax (shipping) . . . . . . . . . [phone]

tel (consumer products) . . . [phone]

tel . . . . . . . . . . . . . . . [phone]

fax . . . . . . . . . . . . . . . .[phone]

M-Audio UK | Avid Technology • M-Audio | www.maudio.co.uk

Pinewood Studios, Pinewood Road, Iver Heath, Bucks, SL0 0NH, United Kingdom

Technical Support e-mail . . . . . . [e-mail] tel (Mac/PC support) . . [phone]

Sales tel

. . . . . . . . .[phone]

M-Audio Benelux | Avid Technology • M-Audio | www.m-audio.com

Vreelandseweg 42 A, 1216 CH Hilversum, The Netherlands

Technical Support Belgium / Luxemburg tel . . .[phone] Netherlands tel . . . . . .[phone]

tel

Sales e-mail

. . . . . . . . [e-mail]

. . . . . . . . . . . [phone]

. . . . . . . . . . . [phone]

fax

M-Audio France | Avid Technology • M-Audio | www.m-audio.fr

44 Avenue Georges Pompidou, 92300 Levallois-Perret, France

Renseignements
Commerciaux

Assistance
Technique

email . . . . . . . . . . . . . . . [e-mail] tel . . . . . . . . . . . . . . 0 810 001 105

e-mail (PC)

email (Mac) . . . . . . . . . . [e-mail]

. . . . . . . [e-mail]

PC . . . . . . . . . . . . . . 0 820 000 731

Mac . . . . . . . . . . . . . 0 820 391 191

fax . . . . . . . . . . [phone]

M-Audio Germany | Avid Technology • M-Audio | www.m-audio.de

Zeppelinstr. 1, D-85399 Hallbergmoos, Germany

Technical Support email . . . . . . . . . . . . [e-mail] tel . . . . . . . . . +49 (0)7941 - 9870030

Sales e-mail

. . . . . . . . . . . . . [e-mail]

tel . . . . . . . . . . [phone]

fax . . . . . . . . . . [phone]

M-Audio Canada | Avid Technology • M-Audio | www.m-audio.ca

1400 St-Jean Baptiste Ave. #150, Quebec City, Quebec G2E 5B7, Canada

Technical Support e-mail . . . . . . . [e-mail]

Sales e-mail

. . . . . . . . [e-mail]

tel . . . . . . . . . . . . . .[phone]

fax . . . . . . . . . . . . . .[phone]

tel . . . . . . . . . . . . . .[phone]

fax . . . . . . . . . . . . . .[phone]

M-Audio Japan

〒

107-0052

テクニカル・サポート

（

Technical

Support

セールス

東京都港区赤坂

）

（

Sales

e-mail . . . . . . . [e-mail]

）

e-mail . . . . . . . . . . . . [e-mail]

エムオーディオ／アビッドテクノロジー

|

2-11-7 ATT

ビル

新館

4F（4F ATT Bldg. 2-11-7 Akasaka, Minato-ku Tokyo 107-0052 Japan

株式会社

tel

. . . . . . . . . . . . . . 03-3505-4034

. . . . . . . . . . . . . . 03-3505-3417

fax

tel

. . . . . . . . . . . . . . 03-3505-7963

. . . . . . . . . . . . . . 03-3505-3417

fax

www.m-audio.jp

|

）