M-Audio BXSUBWOOFER User manual

User Guide

English ( 3 – 10 )

Guía del usuario

Español ( 11 – 18 )

Guide d'utilisation

Français ( 19 – 26 )

Guida per l'uso

Italiano ( 27 – 34 )

Benutzerhandbuch

Deutsch ( 35 – 42 )

Appendix

English ( 43 )

User Guide (English)

Introduction

About the BX Subwoofer

Thank you for choosing the M-Audio BX Subwoofer. The BX Subwoofer has been designed to integrate seamlessly with M-Audio's M3 series, BX series, or other lines of active studio monitors, extending the low-frequency response of the total monitoring system down to 20 Hz. Moreover, the versatile design of BX Subwoofer allows it to work well with any combination of active studio monitors in a two-channel stereo or multichannel surround environment.

Box Contents

BX Subwoofer Power Cable Momentary Footswitch (4) Removable Feet User Guide Safety & Warranty Manual

Support

For the latest information about this product (system requirements, compatibility information, etc.) and product registration, visit m-audio.com/bxsubwoofer.

For additional product support, visit m-audio.com/support.

Quick Start / Connection Diagram

(for Subwoofer Bypass)

Audio Interface

Power

Any items not listed in the Box Contents are sold separately.

Powered Direct-Field

Monitors

Footswitch

subwoofer bypass)

(for

Features

Front Panel

1. Subwoofer Driver: Redesigned and

upgraded for the BX Subwoofer, the transducer driver utilizes a 10" (25.4 cm) composite diaphragm and well damped rubber surround, all driven by a high-temperature voice coil. It is designed to deliver a tight and punchy low-frequency response (in contrast to the "boomy" or "hyped" response that is often characteristic of underdamped subwoofers). The driver's high Bl factor (electromagnet force factor) creates a powerful motor that allows the cone to follow the input signal very accurately, resulting in excellent low-frequency extension and transient response.

2. LED Indicator: The LED Indicator

lights up blue when the subwoofer is powered on. When the Subwoofer

Bypass feature is engaged, the LED Indicator will flash red to indicate

that no sound is coming out of the subwoofer and that the fullbandwidth signal is being routed to the direct-field monitors. While in Thermal Protection mode, the LED Indicator will illuminate solid red, and no audio will be heard from the subwoofer.

Rear Panel

1. AC Voltage Selector: Set this

switch to the correct setting for your location: 115 V and 230 V. Use the 115 V setting for the USA and Japan, or use the 230 V setting for most of the UK and Europe. Make sure this switch is in the proper position for your area before attaching the power cable.

2. Power Input: Use a standard IEC

power cable (included) to connect this input to a power outlet.

3. Power Switch: Use this switch to

turn the subwoofer on and off.

6 7

4 10

4. Subwoofer Bypass: Connect the included footswitch to this input, and then use the footswitch

to momentarily bypass the low frequencies generated by the subwoofer (including the amp, driver, and crossover), sending the full-bandwidth signal directly to your main monitors. This lets you conveniently audition mixes with and without the low-frequency extension of the subwoofer. The LED Indicator on the front of the subwoofer flashes red when in Bypass Mode.

Note: You can use any two-position footswitch, such as an electronic keyboard sustain pedal.

5. XLR Inputs: Use these inputs for XLR connections with either balanced or unbalanced wiring.

Use XLR connectors with this wiring configuration:

• XLR Pin 1: signal ground (shield)

• XLR Pin 2: signal positive (+)

• XLR Pin 3: signal negative (–)

6. TRS Inputs: Use these inputs for 1/4" (6.35 mm) connections with either balanced or

unbalanced wiring. For balanced wiring, use a three-conductor TRS connector with this wiring configuration:

• TRS tip: signal positive (+)

• TRS ring: signal negative (–)

• TRS sleeve: signal ground (shield)

For unbalanced wiring, use a 1/4" (6.35 mm) connector—either with two conductors (TS) or three conductors (TRS). A two-conductor (TS) connector automatically grounds the signal negative input, whereas a three-conductor (TRS) connector, wired unbalanced, provides the option of leaving the negative input open or grounded. We recommend grounding the unused negative input, which you can do by wiring the ring and sleeve of the TRS plug together.

Note: If the TRS Inputs and XLR Inputs are connected at the same time, the TRS Inputs will take priority, and the XLR Inputs will be muted. If the RCA Inputs are used at the same time as either of the TRS Inputs or XLR Inputs, audio will be heard from both. However, we recommend not playing audio through both connectors simultaneously, which can overload the inputs, resulting in clipping (distortion) at the inputs.

7. RCA Inputs: Use these inputs for unbalanced RCA connections.

8. XLR Outputs: Use these outputs for XLR connections, with either balanced or unbalanced

wiring, to send the audio signal to your stereo direct-field monitors. Use XLR connectors with this wiring configuration:

• XLR Pin 1: signal ground (shield)

• XLR Pin 2: signal positive (+)

• XLR Pin 3: signal negative (–)

9. TRS Outputs: Use these outputs for 1/4" (6.35 mm) connections, with either balanced or

unbalanced wiring, to send the audio signal to your stereo direct-field monitors. For balanced wiring, use a three-conductor TRS connector with this wiring configuration:

• TRS tip: signal positive (+)

• TRS ring: signal negative (–)

• TRS sleeve: signal ground (shield)

10. Volume Control: Use this control to set the output gain from the subwoofer.

11. Variable Crossover: You can use this subwoofer in a variety of monitoring contexts, from two-

channel to multichannel (e.g., 5.1, 7.1) systems, and as an accompaniment to practically any direct-field monitors. To this end, we have provided a versatile yet efficient way to tailor the subwoofer's response to work well in any typical monitoring system.

For a two-channel system, there is an in-line low-pass filter control that lets you adjust the crossover frequency. You can set it anywhere from 50 Hz to 200 Hz. It splits the signal by routing everything below that frequency to the subwoofer and everything above it to your main monitors. By using a fourth-order Linkwitz-Riley topology, the circuit enables you to achieve the flattest net response through the crossover point.

For multichannel systems, this subwoofer can reproduce just the output of the LFE (lowfrequency effects) channel, or it can reproduce the bass from some or all of the main channels using conventional multichannel bass management schemes. In this application, you can simply "open up" the subwoofer fully by setting it to 200 Hz (for use with external bass managers), or you can set it to 120 Hz (to comply with the Dolby® Digital standard for the LFE band limit).

12. Phase Selector: Because low-frequency signals have long wavelengths compared to the

dimensions of most rooms, subwoofers can cause phasing or cancellations that can be quite dramatic. For this reason, we have included a phase inversion switch, which causes a 180° phase shift in the subwoofer's output. This gives you more freedom in choosing where to locate the subwoofer (and consequently, the crossover frequency phase alignment) in your monitoring environment. Note that this function affects only the signal going to the subwoofer amplifier, not the signal going to your direct-field monitors.

13. Bass Reflex Port: This subwoofer has a vented enclosure containing a custom bass-reflex port

tube with a circular cross section on the rear of the enclosure. The port effectively gives the subwoofer a smooth response down to 20 Hz, and since its low-frequency contribution complements that of the front-firing woofer driver, the woofer stays linear and distortion-free throughout the passband. The port has also been designed using Failure Mode and Effects Analysis (FMEA) software in order to maximize output and minimize audible port air turbulence noise.

14. Power Amplifier (not pictured): To generate a powerful, tight bass response, this subwoofer

uses a 240-watt amplifier with customized discrete transistor architecture. The amplifier has a carefully designed damping factor which, in conjunction with the mechanical and electromechanical systems built into the driver, helps eliminate the natural tendency of the driver to "ring" after input signal has ceased. This results in an extremely accurate and controlled bass response. You will notice that kick drums and staccato bass notes reproduced by the subwoofer are tight and solid, as though coming from a large acoustic suspension system.

15. Enclosure (not pictured): Like the other components, the subwoofer's enclosure has an

important role in shaping the overall sonic response. To provide more stable performance, this subwoofer employs a special high-acoustic-efficiency medium-density fiberboard (MDF) and unique interior reinforcement designed to reduce sonic coloration and absorb vibration generated by the subwoofer's high-SPL signals and transients. Additionally, the cabinet uses carefully placed acoustic foam to absorb internal reflections and dampen standing waves. This effectively makes the enclosure behave as though it were larger, resulting in a system more capable of reproducing very low-frequency signals naturally and evenly.

16. Thermal Protection (not pictured): The subwoofer's thermal protection protects it from

overheating. If a critical internal temperature is reached, the subwoofer's amplifier will temporarily shut off until the temperature returns to a lower level. While in this protection mode,

LED Indicator will illuminate solid red, and no audio will be heard from the subwoofer.

the Once its internal temperature has dropped sufficiently, audio output will resume automatically, and the LED Indicator will illuminate blue again.

Setup

Connecting the Power

AC Voltage Select: Since this subwoofer contains its own amplifier, it must be connected to a

power outlet using a standard IEC cable (included). Before connecting the subwoofer to a power outlet, set the AC Voltage Selector to the proper setting for your location: 115 V (for the USA and Japan) or 230 V (for most of the UK and Europe).

Warning: Setting an improper voltage selector setting may result in hazardous conditions and/or damage to speaker components not covered by speaker warranty.

Connecting Audio

Two-Channel Stereo Operation

Connect the main left and right outputs of your mixing console, audio interface, or sound card to the subwoofer's XLR Inputs, TRS Inputs, or RCA Inputs, and then connect the subwoofer's left and right XLR Outputs or TRS Outputs to your direct-field, full-range monitors.

While the TRS Inputs and TRS Outputs will work with unbalanced cables, we strongly recommend using balanced cables, which provides better immunity to inductively coupled noise from power cables, etc. For balanced wiring, use this wiring configuration:

• XLR Pin 1 or TRS sleeve: signal ground (shield)

• XLR Pin 2 or TRS tip: signal positive (+)

• XLR Pin 3 or TRS ring: signal negative (–)

Audio Interface

Power

Powered Direct-Field

Monitors

Footswitch

subwoofer bypass)

(for

Multichannel Operation (e.g., 5.1 channel surround)

For mixing or monitoring a multichannel source, you undoubtedly have an external bass management system and/or you may be sending the LFE (low-frequency effects) channel directly to the subwoofer with no additional signal redirection. In this scenario, route your subwoofer's audio signal to either the left or right input on the BX Subwoofer. Also, bypass the BX Subwoofer's internal crossover by setting its Variable Crossover control to 200 Hz (fully open).

Note: More information on using a subwoofer for multichannel applications may be found at dolby.com, dts.com, or thx.com. These websites are examples only and are in no way

associated or affiliated with M-Audio or inMusic Brands, Inc. M-Audio does not guarantee the performance or availability of these services. The BX Subwoofer is not endorsed, sponsored, or approved by these companies.

Audio Interface, Mixer, etc.

Bass Management System

Center-Front

Monitor

Left-Front

Monitor

Left Surround

Monitor

Right-Front

Monitor

Right Surround

Monitor

You

Adjusting the Back Panel Controls

Variable Crossover Control: We have touched on this topic already, but here are a few more points

to keep in mind:

• The crossovers of most audio/video home theater systems are set to 80 Hz (assuming they are

being used with a subwoofer). So if you are mixing multichannel material using the BX Subwoofer, we recommend starting with the 80 Hz setting as a reference to approximate a typical end-user listening environment.

• For easy compliance with Dolby® Digital, DTS®, and THX® recommendations, we have provided

calibrated markings on the crossover dial for 80 Hz, 100 Hz, and 120 Hz positions (in addition to 50 Hz and 200 Hz).

• If you are using the BX Subwoofer with direct-field monitors in a two-channel setup, we recommend starting with the crossover frequencies listed below (depending on your monitor's driver size) and adjusting it to suit your particular environment:

o 5" (127 mm) drivers (such as the M-Audio BX5 Carbon or BX5 D2): 80 Hz. o 6" (152 mm) drivers (such as the M-Audio M3-6 or BX6 Carbon): 65 Hz. o 8" (203 mm) drivers (such as the M-Audio M3-8, BX8 Carbon, or BX8 D2): 50 Hz.

• Check the documentation of your direct-field monitors to see if it recommends a specific subwoofer crossover frequency.

Phase Selector: As we mentioned before, this switch inverts the signal (the phase angle from 0° to 180°) that goes to the subwoofer amplifier. This function does not affect the signal going to your direct-field monitors. Set the appropriate position of this switch by listening to how the sound from the BX Subwoofer blends with the rest of your system. There is no "right" or "wrong" position, but the subwoofer should be "phase-coherent" with your direct-field monitors at the crossover frequency and have no audible energy cancellation. You can determine this by playing a sine wave signal at the crossover frequency and putting the Phase Selector in the position that gives you the strongest output.

Volume Control: You should always send a line-level signal to the subwoofer's inputs. When the Volume Control is all the way up, 85 mV of pink noise at the input will produce a 100 dBA output

SPL at one meter from the front baffle. The Volume Control affects the level going to the subwoofer amplifier, not the level of the subwoofer outputs send to your direct-field monitors.

Generally, we recommend trying to get the flattest, most even system response between your subwoofer and your direct-field monitors. Depending on the acoustics of your environment and the setup of your signal path and levels, spend a few minutes calibrating the respective levels of the subwoofer and each of your main monitors. If you have access to pink noise signals and/or swept sine waves (linear and logarithmic), they can help ensure your system has the smoothest tonal balance from top to bottom.

Subwoofer Bypass: This 1/4" (6.35 mm) mono input is for connecting a non-latching footswitch like the M-Audio SP-1 (or any similar sustain pedal for a keyboard controller). In two-channel scenarios, toggling the footswitch triggers a relay circuit that mutes the subwoofer's output and re-routes the full-bandwidth audio signal to your direct-field monitors. In essence, this removes the subwoofer (with its crossover) from the signal path so you can easily audition your mixes both with and without the subwoofer's low-frequency extension. This can also be useful in multichannel operation.

When the subwoofer is in Bypass Mode, the LED Indicator on the front panel flashes red.

Note: More information on using a subwoofer for multichannel applications may be found at dolby.com, dts.com, or thx.com. These websites are examples only and are in no way associated

or affiliated with M-Audio or inMusic Brands, Inc. M-Audio does not guarantee the performance or availability of these services. The BX Subwoofer is not endorsed, sponsored, or approved by these companies.

Placing the BX Subwoofer

The "location, location, location" cliché applies to more than just the real estate market. It is equally (if not more) applicable to loudspeakers and room acoustics. Where you place the BX Subwoofer in your room can have a huge impact on how it will sound. In fact, any welldesigned, powerful subwoofer can sound like a complete dud in your monitoring setup if you have placed it poorly. (This applies for any loudspeaker, but it is especially true for lowfrequency reproducers like subwoofers.)

There are many opinions on the best method to determine the optimal location for your subwoofer (if you ask three different studio engineers, they will probably give you six different answers), but we cannot emphasize enough how important this issue is.

Things to Remember

Always place the subwoofer on the floor when you are using it, never on a table or speaker stand.

Take time to consider your subwoofer's placement, keeping in mind that the shape of your room, its dimensions (including ceiling height), the wall construction, any acoustic treatment, and other obstacles like furniture can affect the subwoofer's apparent performance.

Remember that the frequency of any given signal is inversely proportional to its wavelength (e.g,. at 40 Hz, one wavelength is approximately 28 feet [8.5 meters]; at 80 Hz, one wavelength is a little over 14 feet [four meters]).

Different Methods

One theory suggests that the best position for a subwoofer in a two-channel system is on the floor halfway between your left and right direct-field monitors, with its front facing forward and in the same plane as the direct-field speakers. From there, you can adjust the subwoofer's position until it is most "correct."

Another theory dictates that you should start with the subwoofer in a corner of the room's floor, where the adjacent walls can help the subwoofer maximize the amount of sound it radiates; and then you can adjust the position to suit your specific monitoring setup.

Another method that many mix engineers have employed with great success uses the law of bilateral symmetry. Place the subwoofer in the chair in your listening position (presumably, this is at the apex of an isosceles triangle between your left and right direct-field monitors). Play some music with substantial bass frequencies (pink noise works well, too) into the subwoofer at a comfortable listening level. Get down on the floor of the room and listen for a place where the sound is "fullest" but also "tight"-sounding, and place your subwoofer there. To be more precise, use a 1/12th-octave real-time spectrum analyzer instead of your ears and perform the same exercise using pink noise as the test signal and observing where the spectral response is smoothest and has the greatest low-frequency extension.

Further Adjustments

Because low-frequency signals radiate omnidirectionally, you may find that the best location sonically for the subwoofer is inconvenient (like in an area of your studio with a lot of foot traffic). If this is the case, try flipping the Phase Selector on the rear panel and repeat the exercise to see if you can find a more convenient place.

Finally, once you have placed the subwoofer where you believe it will sound best, play some material along with direct-field monitors, listening from your standard mix position. Make sure the subwoofer's Volume Control, Phase Selector, and Variable Crossover are set appropriately. If something sounds "wrong" to you, experiment with other locations and different directions for facing the driver. You may inadvertently find a better placement, even if you think its current location already sounds good.

Guía del usuario (Español)

Introducción

Acerca del BX Subwoofer

Gracias por elegir el BX Subwoofer de M-Audio. El BX Subwoofer fue diseñado para integrarse fluidamente con las series M3, BX y otras líneas de monitores de estudio activos de M-Audio, extendiendo la respuesta en frecuencias baja del sistema de monitoreo total hasta 20 Hz. Más aún, el diseño versátil BX Subwoofer le permite trabajar bien con cualquier combinación de monitores de estudio activos en ambientes estéreo de dos canales o surround multicanal.

Contenido de la caja

BX Subwoofer Cable de alimentación Interruptor de pedal momentáneo (4) Patas desmontables Guía del usuario Manual sobre la seguridad y garantía

Soporte

Para obtener la información más reciente acerca de este producto (requisitos de sistema, información de compatibilidad, etc.) y el registro del producto, visite m-audio.com/bxsubwoofer.

Para obtener soporte adicional del producto, visite m-audio.com/support.

Diagrama de inicio y conexión rápida

(para puenteo (bypass) del Subwoofer)

Interfaz de audio

Suministro eléctrico

Todo elemento que no se enumere en Contenido de la caja se vende por separado.

Monitores alimentados

de campo directo

Interruptor de pedal

(para puenteo (bypass) del subwoofer)

Características

Panel frontal

1. Driver del Subwoofer: Rediseñado y

mejorado para el BX Subwoofer, el driver del transductor utiliza un diafragma compuesto de 25,4 cm (10 pulg.) y una envoltura de goma de alta amortiguación, todo accionado por una bobina de voz de alta temperatura. Está diseñado para brindar una respuesta en baja frecuencia apretada e intensa (a diferencia de la respuesta "retumbante" o "exagerada" que se encuentra a menudo en los subwoofers sin amortiguación). El gran factor Bl del driver (factor de fuerza del electroimán) crea un poderoso motor que permite que el cono siga la señal con gran precisión, dando como resultado una excelente extensión en baja frecuencia y respuesta transitoria.

2. Indicador de LED: El LED indicador se enciende en azul cuando el subwoofer está encendido. Cuando se activa la característica de puenteo del Subwoofer, el LED indicador parpadeará en rojo para indicar que no está saliendo sonido por el subwoofer y que la señal de ancho de banda completo se está direccionando a los monitores de campo directo. Mientras esté en modo Protección térmica, el LED indicador se iluminará en rojo, y el subwoofer no emitirá ningún sonido.

Panel trasero

1. Selector de voltaje de CA: Ajuste este interruptor según el voltaje en su ubicación: 115 V y 230 V. Utilice 115 V para EE.UU. y Japón, y 230 V para la mayoría del Reino Unido y Europa. Asegúrese de que este interruptor esté en la posición correspondiente a su región antes de conectar el cable de corriente.

2. Entrada de corriente: Utilice el cable de alimentación IEC estándar incluido para conectar esta entrada a una toma de corriente.

3. Interruptor de encendido: Utilice este interruptor para encender y apagar el subwoofer.

6 7

4 10

4. Puenteo (bypass) del subwoofer: Conecte a esta entrada el interruptor de pedal incluido, y a continuación utilícelo para puentear provisoriamente las frecuencias bajas generadas por el subwoofer (incluyendo el amplificador, driver y crossover), enviando la señal de ancho de banda completo directamente a sus monitores principales. Esto le permite escuchar mezclas con y sin la extensión de baja frecuencia del subwoofer convenientemente. El LED indicador en el frente del subwoofer parpadea en rojo cuando se activa el modo Puenteo.

Nota: Puede utilizar un interruptor de pedal de dos posiciones, como por ejemplo el pedal de sostenido de un teclado.

5. Entradas XLR: Utilice estas entradas para conexiones XLR ya sea con cableado balanceado o no balanceado.

Utilice conectores XLR con esta configuración de cableado:

• Patilla XLR 1: tierra de la señal (malla del cable)

• Patilla XLR 2: positivo de la señal (+)

• Patilla XLR 3: negativo de la señal (–)

6. Entradas TRS: Utilice estas entradas para conexiones de 6,35 mm (1/4 pulg.) ya sea con cableado balanceado o no balanceado.

Para cableado balanceado, utilice un conector TRS de tres conductores con la siguiente configuración de cableado:

• Punta del TRS: positivo de la señal (+)

• Nuca del TRS: negativo de la señal (–)

• Manguito del TRS: tierra de la señal (malla del cable)

Para cableados desbalanceados, utilice un conector de 6,35 mm (1/4 pulg.) —ya sea con dos conductores (TS) o tres (TRS). Un conector de dos conductores (TS) pone a tierra automáticamente la entrada negativa de la señal, mientras que un conector de tres conductores (TRS), de cableado desbalanceado, brinda la opción de dejar la entrada negativa abierta o de ponerla a tierra. Recomendamos poner a tierra la entrada negativa en desuso, cosa que puede hacer cableando la nuca y el manguito del conector TRS juntos.

Nota: Si las entradas TRS y XLR están conectadas simultáneamente, las entradas TRS tendrán prioridad y las entradas XLR quedarán silenciadas. Si las entradas RCA se usan al mismo tiempo que cualquiera de las entradas TRS o XLR, se escuchará el sonido proveniente de ambas. No obstante, recomendamos no reproducir audio a través de ambos conectores simultáneamente, dado que pueden sobrecargarse las entradas y producir recorte (distorsión) en las mismas.

7. Entradas RCA: Utilice estas entradas para conexiones RCA no balanceadas.

8. Salidas XLR: Utilice estas salidas para conexiones XLR, ya sea con cableado balanceado o no balanceado, para enviar la señal de audio a sus monitores estéreo de campo directo.

Utilice conectores XLR con esta configuración de cableado:

• Patilla XLR 1: tierra de la señal (malla del cable)

• Patilla XLR 2: positivo de la señal (+)

• Patilla XLR 3: negativo de la señal (–)

9. Salidas TRS: Utilice estas salidas para conexiones de 6,35 mm (1/4 pulg.), ya sea con cableado balanceado o no balanceado, para enviar la señal de audio a sus monitores estéreo de campo directo.

Para cableado balanceado, utilice un conector TRS de tres conductores con la siguiente configuración de cableado:

• Punta del TRS: positivo de la señal (+)

• Nuca del TRS: negativo de la señal (–)

• Manguito del TRS: tierra de la señal (malla del cable)

10. Control de volumen: Utilice este control para ajustar la ganancia de salida del subwoofer.

11. Crossover variable: Puede utilizar este subwoofer en una gran variedad de contextos de monitoreo, desde sistemas de dos canales hasta sistemas multicanal (ej, 5.1, 7.1), y como acompañamiento para prácticamente cualquier monitor de campo directo. Para este propósito hemos provisto una manera versátil pero eficiente de diseñar la respuesta del subwoofer para que funcione bien en cualquier sistema de monitoreo típico.

Para un sistema de dos canales, existe un control de filtro pasabajos en línea que le permite ajustar la frecuencia de cruce (crossover). Puede ajustar entre 50 a 200 Hz. Divide la señal direccionando todo lo que esté debajo de esta frecuencia hacia el subwoofer y todo lo que esté arriba de ella hacia sus monitores principales. Gracias a su topología Linkwitz-Riley de cuarto orden, el circuito le permite obtener la respuesta neta más plana a través del punto de crossover.

Para sistemas multicanal, este subwoofer puede reproducir solamente la salida del canal de LFE (efectos de baja frecuencia), o puede reproducir los graves de algunos o de todos los canales principales utilizando esquemas de gestión de bajos multicanal convencionales. En esta aplicación, puede simplemente "abrir" el subwoofer completamente ajustándolo a 200 Hz (para utilizarlo con administradores de graves externos), o puede ajustarlo a 120 Hz (para cumplir con la norma Dolby® Digital de límite de banda de LFE).

12. Selector de fase: Debido a que las señales de baja frecuencia tienen longitudes de onda más largas comparadas con las dimensiones de la mayoría de las salas, los subwoofers pueden causar desplazamientos o cancelaciones de fase que pueden ser dramáticas. Por este motivo hemos incluido un interruptor de inversión de fase, que causa un desplazamiento de 180° en la salida del subwoofer. Esto le brinda una mayor libertad para elegir la ubicación del subwoofer (y en consecuencia, la alineación de la fase de la frecuencia de crossover) en su ambiente de monitoreo. Note que esta función afecta solamente a la señal que se dirige al amplificador del subwoofer, no a la que se dirige a sus monitores de campo directo.

13. Puerto de reflexión de graves: Este subwoofer posee un gabinete con una apertura que contiene un recinto tubular para reflexión de graves de sección circular en la parte posterior del gabinete. Esta apertura le brinda al subwoofer una respuesta suave hasta 20 Hz, y dado que su contribución a las bajas frecuencias complementa a la del driver del woofer de la parte delantera, el woofer permanece lineal y libre de distorsiones a lo largo del pasabanda. El puerto también se ha diseñado utilizando un software de modo de fallo y análisis de efectos (FMEA) a fin de maximizar la salida y minimizar el ruido audible causado por la turbulencia del aire en la abertura.

14. Amplificador alimentado (no aparece en el gráfico): Para generar una respuesta de graves poderosa y apretada, este subwoofer utiliza un amplificador de 240 W con una arquitectura de transistores discretos personalizada. El amplificador posee un factor de amortiguación cuidadosamente diseñado que, junto con los sistemas mecánicos y electromecánicos incorporados en el driver, ayuda a eliminar la tendencia natural del driver de resonar cuando cesa la señal de entrada. Esto da como resultado una respuesta de graves extremadamente precisa y controlada. Notará que los bombos y las notas de bajo staccato que reproduce el subwoofer son apretadas y sólidas, como si vinieran de un gran sistema de suspensión acústica.

15. Gabinete (no aparece en el gráfico): Al igual que los otros componentes, el gabinete del subwoofer desempeña un papel importante en darle forma a la respuesta de sonido total. Para brindar un desempeño más estable, este subwoofer emplea tableros de fibra (MDF) de densidad media y de alta eficiencia acústica y un refuerzo interior único diseñado para reducir la coloración del sonido y absorber la vibración generada por las señales de alto SPL y los transitorios del subwoofer. Además, el gabinete utiliza espuma acústica cuidadosamente colocada para absorber las reflexiones internas y amortiguar las ondas estacionarias. Esto logra que el gabinete se comporte como si fuera de mayor tamaño, dando como resultado un sistema capaz de reproducir señales de muy baja frecuencia de forma natural y pareja.

16. Protección térmica (no aparece en el gráfico): La protección térmica evita que el subwoofer se sobrecaliente. Si se alcanza la temperatura interna crítica, el amplificador del subwoofer se apagará temporalmente hasta que la temperatura regrese a un nivel menor. Mientras esté en este modo de protección, el LED indicador se iluminará en rojo, y el subwoofer no emitirá ningún sonido. Una vez que la temperatura interna haya disminuido lo suficiente, continuará la emisión de audio automáticamente, y el LED indicador se iluminará en azul nuevamente.

+ 30 hidden pages