Marantz ST6001 User Manual

Model ST6001 User Guide

FM / AM Tuner

ENGLISH

WARRANTY

For warranty information, contact your local Marantz distributor.

RETAIN YOUR PURCHASE RECEIPT

Your purchase receipt is your permanent record of a valuable purchase.
It should be kept in a safe place to be referred to as necessary for
insurance purposes or when corresponding with Marantz.

IMPORTANT

When seeking warranty service, it is the responsibility of the consumer
to establish proof and date of purchase. Your purchase receipt or
invoice is adequate for such proof.

FOR U.K. ONLY

This undertaking is in addition to a consumer's statutory rights and does
not affect those rights in any way.

FRANÇAIS

GARANTIE

Pour des informations sur la garantie, contacter le distributeur local
Marantz.

CONSERVER L'ATTESTATION D'ACHAT

L'attestation d'achat est la preuve permanente d'un achat de valeur. La
conserver en lieu sur pour s'y reporter aux fins d'obtention d'une
couverture d'assurance ou dans le cadre de correspondances avec
Marantz.

IMPORTANT

Pour l'obtention d'un service couvert par la garantie, il incombe au client
d'établir la preuve de l'achat et d'en corroborer la date. Le reçu ou la
facture constituent des preuves suffisantes.

DEUTSCH

GARANTIE

Bei Garantiefragen wenden Sie sich bitte an Ihren Marantz-Händler.

HEBEN SIE IHRE QUITTING GUT AUF

Die Quittung dient Ihnen als bleibende Unterlage für Ihren wertvollen
Einkauf Das Aufbewahren der Quittung ist wichtig, da die darin
enthaltenen Angaben für Versicherungswecke oder bei Korrespondenz
mit Marantz angeführt werden müssen.

WICHTIG!

Bei Garantiefragen muß der Kunde eine Kaufunterlage mit Kaufdatum
vorlegen. Ihren Quittung oder Rechnung ist als Unterlage ausreichend.

NEDERLANDS

GARANTIE

Voor inlichtingen omtrent garantie dient u zich tot uw plaatselijke
Marantz.

UW KWITANTIE, KASSABON E.D. BEWAREN

Uw kwitantie, kassabon e.d. vormen uw bewijs van aankoop van een
waardevol artikel en dienen op een veilige plaats bewaard te worden
voor evt, verwijzing bijv, in verbend met verzekering of bij
correspondentie met Marantz.

BELANGRIJK

Bij een evt, beroep op de garantie is het de verantwoordelijkheid van de
consument een gedateerd bewijs van aankoop te tonen. Uw kassabon
of factuurzijn voldoende bewijs.

ESPAÑOL

GARANTIA

Para obtener información acerca de la garantia póngase en contacto
con su distribuidor Marantz.

GUARDE SU RECIBO DE COMPRA

Su recibo de compra es su prueba permanente de haber adquirido un
aparato de valor, Este recibo deberá guardarlo en un lugar seguro y
utilizarlo como referencia cuando tenga que hacer uso del seguro o se
ponga en contacto con Marantz.

IMPORTANTE

Cuando solicite el servicio otorgado por la garantia el usuario tiene la
responsabilidad de demonstrar cuándo efectuó la compra. En este
caso, su recibo de compra será la prueba apropiada.

ITALIANO

GARANZIA

L’apparecchio è coperto da una garanzia di buon funzionamento della
durata di un anno, o del periodo previsto dalla legge, a partire dalla data
di acquisto comprovata da un documento attestante il nominativo del
Rivenditore e la data di vendita. La garanzia sarà prestata con la
sostituzione o la riparazione gratuita delle parti difettose.
Non sono coperti da garanzia difetti derivanti da uso improprio, errata
installazione, manutenzione effettuata da personale non autorizzato o,
comunque, da circostanze che non possano riferirsi a difetti di
funzionamento dell’apparecchio. Sono inoltre esclusi dalla garanzia gli
interventi inerenti l’installazione e l’allacciamento agli impianti di
alimentazione.
Gli apparecchi verranno riparati presso i nostri Centri di Assistenza
Autorizzati. Le spese ed i rischi di trasporto sono a carico del cliente.
La casa costruttrice declina ogni responsabilità per danni diretti o
indiretti provocati dalla inosservanza delle prescrizioni di installazione,
uso e manutenzione dettagliate nel presente manuale o per guasti
dovuti ad uso continuato a fini professionali.

SVENSKA

GARANTI

För information om garantin, kontakta Marantz lokalagent.

SPAR KVITTOT

Kvittot är ett inköpsbevis på en värdefull vara. Det skall förvaras säkert
och hänvisas till vid försäkringsfall eller vidkorrespondens mod Marantz.

VIKTIGT

Fö att garantin skall gälla är det kundens sak att framställa bevis och
datum om köpet. Kvitto eller faktura är tillräokligt bevis fö detta.

CE MARKING

English

The ST6001 is in conformity with the EMC directive and low-voltage directive.

Français

Le ST6001 est conforme à la directive EMC et à la directive sur les basses tensions.

Deutsch

Das Modell ST6001 entspricht den EMC-Richtlinien und den Richtlinien für
Niederspannungsgeräte.

Nederlands

De ST6001 voldoet aan de EMC eisen en de vereisten voor laag-voltage.

Español

El ST6001 está de acuerdo con las normas EMC y las relacionadas con baja tensión.

Italiano

Il ST6001 è conforme alle direttive CEE ed a quelle per i bassi voltaggi.

Svenska

ST6001 är tillverkad i enlighet med EMC direktiven och direktiven för
lågvoltsutrusning.

English

WARNINGS

- Do not expose the equipment to rain or moisture.

- Do not remove the cover from the equipment.

- Do not insert anything into the equipment through the ventilation
holes.

- Do not handle the mains cord with wet hands.

- Do not cover the ventilation with any items such as tablecloths,
newspapers, curtains, etc.

- No naked flame sources, such as lighted candles, should be placed
on the equipment.

- When disposing of used batteries, please comply with governmental
regulations or environmental public instruction’s rules that apply in
your country or area.

- Make a space of about 0.1 meter around the unit.

- No objects filled with liquids, such as vases, shall be placed on the
apparatus.

- When the switch is in the OFF position, the equipment is not
completely switched off from MAINS.

- The Socket-Outlet shall be installed near the equipment and shall be
easily accessible.

Français

AVERTISSEMENTS

- Ne pas exposer l’appareil à la pluie ni à l’humidité.

- Ne pas essayer de retirer le boîtier de l’appareil.

- Ne rien insérer dans l’appareil par les orifices de ventilation.

- Ne pas manipuler le cordon d’alimentation avec les mains mouillées.

- Ne pas recouvrir les ouïes de ventilation avec un objet quelconque
comme une nappe, un journal, un rideau, etc.

- Ne placer aucune source de flamme nue, comme une bougie allumée,
sur l'appareil.

- Pour mettre au rebut les piles usées, respecter les lois
gouvernementales ou les règlements officiels concernant
l’environnement qui s'appliquent à votre pays ou région.

- Veiller à ce qu’aucun objet ne soit à moins de 0,1 mètre des côtés de
l'appareil.

- Aucun objet rempli de liquide, un vase par exemple, ne doit être placé
sur l'appareil.

- Lorsque l'interrupteur est sur la position OFF, l'appareil n'est pas
complètement déconnecté du SECTEUR (MAINS).

- La prise électrique doit se trouver près de l'appareil et être facilement
accessible.

Deutsch

WARNHINWEISE

- Das Gerät nicht Regen oder Feuchtigkeit aussetzen.

- Die Abdeckung nicht vom Gerät abnehmen.

- Keine Gegenstände durch die Belüftungsschlitze stecken.

- Das Netzkabel nicht mit feuchten oder nassen Händen anfassen.

- Decken Sie die Lüftungsöffnungen nicht mit einem Tischtuch, einer
Zeitung, einem Vorhang usw. ab.

- Es dürfen keine Gegenstände mit offener Flamme, wie etwa
brennende Kerzen, auf dem Gerät aufgestellt werden.

- Beachten Sie bei der Entsorgung der verbrauchten Batterien alle
geltenden lokalen und überregionalen Regelungen.

- Auf allen Geräteseiten muß ein Zwischenraum von ungefähr 0,1 meter
vorhanden sein.

- Auf das Gerät dürfen keine mit Flüssigkeiten gefüllte Behälter, wie
etwa eine Vase, gestellt werden.

- Wenn der Schalter ausgeschaltet ist (OFF-Position), ist das Gerät
nicht vollständig vom Stromnetz (MAINS) abgetrennt.

- Die Netzsteckdose muss sich in der Nähe des Gerätes befinden, und
ein unbehinderter Zugang dazu muss jederzeit gewährleistet sein.

Nederlands

WAARSCHUWINGEN

- Stel het apparaat niet bloot aan regen of vocht.

- Verwijder de afdekplaat van het apparaat niet.

- Duw niets door de ventilatieopeningen in het apparaat.

- Raak het netsnoer niet met natte handen aan.

- Bedek de ventilatieopeningen niet met enige voorwerpen, zoals
tafelkleden, kranten, gordijnen, enz.

- Plaats geen brandende voorwerpen, zoals kaarsen, op het apparaat.

- Volg bij het weggooien van verbruikte batterijen de
overheidswetgeving of milieuvoorschriften op die van kracht zijn in het
land of de regio waarin u zich bevindt.

- Zorg dat er 0,1 meter vrije ruimte rond het toestel is.

- Plaats geen voorwerpen met een vloeistof erin, zoals een
bloemenvaas, op het apparaat.

- Als de schakelaar op OFF staat, is het apparaat niet volledig
losgekoppeld van de netspanning (MAINS).

- Het stopcontact dient in de buurt van het apparaat te zitten en
eenvoudig bereikbaar te zijn.

Español

- No exponga el equipo a la lluvia ni a la humedad.

- No extraiga la tapa del equipo.

- No introduzca nada en el interior del equipo a través de los orificios de
ventilación.

- No maneje el cable de alimentación con las manos mojadas.

- No cubra la ventilación con objetos como manteles, periódicos,
cortinas, etc.

- No deben colocarse sobre el equipo elementos con fuego, por
ejemplo velas encendidas.

- Cuando se eliminen baterías usadas, deben cumplirse las
reglamentaciones oficiales o las normas de protección
medioambiental aplicables en su país o en su zona.

- Deje un espacio de unos 0,1 metro alrededor de la unidad.

- No se deben colocar sobre el aparato recipientes que contengan
líquidos, como por ejemplo jarrones.

- Cuando el interruptor está en la posición OFF, el equipo no está
completamente desconectado de la alimentación MAINS.

- La toma de corriente se debe instalar cerca del equipo y ser de fácil
acceso.

Italiano

- Non esporre l’apparecchio alla pioggia o all’umidità.

- Non rimuovere il coperchio dell’apparecchio.

- Non introdurre oggetti all’interno dell’apparecchio attraverso i fori di
ventilazione.

- Non toccare il cavo di alimentazione con le mani bagnate.

- Non coprire le fessure di ventilazione con tovaglie, giornali, tende od
oggetti analoghi.

- Non posare sull'apparecchio sorgenti di fiamme scoperte quali
candele accese.

- Smaltire le pile usate in conformità alle norme governative o
disposizioni ambientali vigenti nel proprio paese o zona.

- Lasciare 0,1 metro liberi tutto intorno l'unità.

- Non mettere sull'apparecchiatura alcun contenitore di liquido, come ad
esempio dei vasi.

- Quando l'interruttore è nella posizione OFF, l'apparecchiatura non è
completamente scollegata da MAINS.

- La presa elettrica dovrebbe essere installata in prossimità
dell'apparecchio ed essere facilmente accessibile.

ADVERTENCIAS

AVVERTENZE

Svenska

- Utsätt inte utrustningen för regn eller fukt.

- Ta inte bort utrustningens hölje.

- För inte in föremål i utrustningen genom ventilationshålen.

- Hantera inte nätsladden med våta händer.

- Täck inte för ventilationsöppningarna med några föremål som till
exempel bordsdukar, dagstidningar, gardiner e.d.

- Inga föremål med öppen låga, som till exempel tända stearinljus, bör
placeras på utrustningen.

- Följ de lagar och miljöskyddsråd som gäller i det land eller område där
du bor när du gör dig av med batterier.

- Se till att det finns omkring 0,1 meter fri plats runt omkring enheten.

- Inga objekt som är fyllda med någon vätska, till exempel
blomstervaser, bör placeras på apparaten.

- Även om strömbrytaren står i det avstängda läget OFF, så är
utrustningen inte helt bortkopplad från det elektriska nätet (MAINS).

- Uttaget ska vara installerat nära utrustningen och vara lättillgängligt.

VARNINGAR

CONTENTS

FEATURES .............................................................................................................................................1

BEFORE USE .........................................................................................................................................2

PARTS NAMES AND FUNCTIONS........................................................................................................3

FRONT PANEL ...................................................................................................................................................3

FL-DISPLAY ........................................................................................................................................................4

REAR PANEL......................................................................................................................................................5

CONNECTIONS......................................................................................................................................6

OPERATIONS.........................................................................................................................................7

MEMORY PRESETTING ..................................................................................................................................7

LISTENING TO RADIO .....................................................................................................................................7

FINE, MANUAL TUNING ....................................................................................................................................7

ADJUSTING CURRENT TIME ...........................................................................................................................8

DAILY TIMER .....................................................................................................................................................8

FILING (STATION NAME, ETC.) .......................................................................................................................9

RDS (RADIO DATA SYSTEM) ...........................................................................................................................9

RDS DISPLAY ..................................................................................................................................................10

TROUBLESHOOTING ..........................................................................................................................11

OTHERS ...............................................................................................................................................11

ENGLISH

SPECIFICATIONS & DIMENSIONAL DRAWINGS ..............................................................................12

FEATURES

A NOTE ABOUT RECYCLING

• Max.30-station preset memory (each

FM,AM) with auto preset memory function

• Remote control operation by Marantz

Remote Control Bus

• Select the FM Antenna A/B

• Select the IF band (wide/narrow)

• Fine Tuning

• Daily Timer

This product’s packaging materials are recyclable
and can be reused. This product and the accessories
packed together are the applicable product to the
WEEE directive except batteries.
Please dispose of any materials in accordance with
your local recycling regulations.
When discarding the unit, comply with your local
rules or regulations.
Batteries should never be thrown away or incinerated
but disposed of in accordance with your local
regulations concerning chemical wastes.

1

ENGLISH

FM/AM TUNER ST6001

ANTETTA

IF BAND

FM

ON/STAMDBY

POWER

STANDBY

WIDE

NARROW

AB

RDS

TIMER SET

BAND

ON/OFF

FM MODE

PRESETUPDOWN

UP

DOWN

TUNING

MEMONEXT

CANCEL

TUNING
MODE

/DISPLAY

ST.NAME

TIME ADJ.

TIMER

DAILY ONCE

TUNED STEREO RDS

PTY PT TP TA

PRESET

kHz
MHz

CH

MEMO

BEFORE USE

This section must be read before any connection is made to
the mains supply.

7

EQUIPMENT MAINS WORKING
SETTING

Your Marantz product has been prepared to comply with the
household power and safety requirements that exist in your
area.
ST6001 can be powered by 230V AC only.

7

COPYRIGHT

Recording and playback of any material may require
consent. For further information refer to the following:

-

Copyright Act 1956

-

Dramatic and Musical Performers Act 1958

-

Performers Protection Acts 1963 and 1972

-

Any subsequent statutory enactments and orders

7

Do Not Locate in the Following
Places

To ensure long-lasting use, do not locate the ST6001
where:

• Exposed to direct sunlight.

• Near to sources of heat such as heaters.

• Highly humid or poorly ventilated.

• Dusty.

• Subjected to mechanical vibrations.

• On wobbly, inclined or otherwise unstable surfaces

• Radiated heat is blocked such as in cramped audio racks.

Noise or disturbance of the picture may be generated if this
unit or any other electronic equipment using microprocessors
is used near a tuner or TV.
If this happens, take the following steps:

• Install this unit as far as possible from the tuner or TV.

• Set the antenna wires from the tuner or TV away from this
unit’s mains cord and input/output connection cords.

• Noise or disturbance tends to occur particularly when
using indoor antennas or 300 Ω/ohms feeder wires. We
recommend using outdoor antennas and 75 Ω/ohms
coaxial cables.

Note

For heat dispersal, do not install this equipment in a
confined space such as a book case or similar unit.

7

Accessories Check

Before use, check the below accessories were included in
the package.

• Audio connecting cord x 1

• AM loop antenna x 1

To ensure proper heat radiation, ensure the below
clearance from walls and other equipment.

Left

0.1 m or more

Above

0.1 m or more

0.1 m or more

Right

Rear

0.1 m or more

• FM indoor antenna x 1

• Remote Control Connecting Cord x 1

• User Guide x 1

• Registration Card x 1

2

PARTS NAMES AND FUNCTIONS

FM/AM TUNER ST6001

ANTETTA

IF BAND

FM

ON/STAMDBY

POWER

STANDBY

WIDE

NARROW

AB

RDS

TIMER SET

BAND

ON/OFF

FM MODE

PRESET

UP

DOWN

UP

DOWN

TUNING

MEMONEXT

CANCEL

TUNING

MODE

/DISPLAY

ST.NAME

TIME ADJ.

TIMER

DAILY

TUNED STEREO RDS

PTY TP TA

PRESET

kHz
MHz

CH

MEMO

qew r tyu oi!0!1

!2 !3 !4

!5 !6 !7

!8

@0!9

FRONT PANEL

q POWER ON /STANDBY button

This button is used to power on or power standby.

w STANDBY indicator

This indicator illuminates red when the unit’s status is
standby.
When daily timer is activated, this indicator lights green.

e ANTENNA A/B button

This button is used selection of the FM antenna A or B.

ENGLISH

!0 NEXT button

This button is used for advancing to the next step during
time adjustment or manual filing, etc.

!1 MEMO button

This button is used for presetting the broadcasting
stations.

!2 (Timer) ON/OFF button

This button used for engaging the daily timer function.

r IF BAND button

This button is used for selecting the bandwidth of the FM
broadcast.

t TIME ADJ (adjust) button

This button is used for adjusting the current time.

y ST.NAME/DISPLAY button

This button is used for displaying the signal strength.

FM

More than 50dB
25dB-49dB
10dB

-

24dB

Less than 9dB

MW/LW

More than 75dB

-

74dB

60dB
50dB

-

59dB

Less than 49dB

Condition

Signal strength is good
Signal strength is marginal
Signal strength is poor
Loss of the signal

Press this button slightly longer (for more than 1.5
second) to file in manually stations name in the preset
memory.

u TUNING MODE button

This button is used for selecting the manual tuning or the
fine tuning mode. Fine tuning mode is available only in
the FM band.

i TUNING 5∞ (UP/DOWN) button

This button used for tuning in the desired broadcasting
stations or adjusting the time, or manual tuning, etc.

o CANCEL button

This button is used for canceling the program during
manual file or adjusting the on/off time of the timer.

!3 TIMER SET button

This button is used for presetting the time when the
system is turned on and off every day at a specified
time.

!4 PRESET 5∞ (UP/DOWN) button

This button used for preset in the desired broadcasting
stations.

!5 FM MODE button

This unit automatically switches into the STEREO mode
when a FM stereo broadcast is received press this
button to change the monaural mode, then the
“STEREO” indicator will go out on the display.

!6 RDS button

When the FM RDS broadcasting is displayed, and it
retrieves, this button is operated. (See page 9)

!7 BAND button

This button is used for selecting the FM, MW or LW
broadcast.

!8 DISPLAY/INDICATOR

!9 Antenna A or B indicator

@0 FM WIDE or NARROW band indicator

3

ENGLISH

TIMER

DAILY

TUNED STEREO RDS PTY TP TA

PRESET

kHz

MHz

CH

MEMO

ca b

g

h

d

ef

FL-DISPLAY

PARTS NAMES AND FUNCTIONS

a TIMER

This indicator lights up when the daily timer is activated.

b DAILY timer indicator

This indicator lights up when the daily timer is engaged
by pressing the TIMER SET button.

c TUNED indicator

This indicator lights up when a station is properly tuned
in.

d STEREO indicator

This indicator lights up when an FM station is being
tuned into stereo condition.

e RDS indicators

These indicators light up when receiving RDS
broadcasts.

f MEMORY indicator

When the MEMO button is pressed, this indicator blinks
for about 8 seconds.

g PRESET Number indicator

Shows the selected preset number.

h CHARACTER indicator

A variety of information is displayed on this indicator.
Time, frequency, PS, PTY, RT, stations name by manual
filing. etc.

4

PARTS NAMES AND FUNCTIONS

〜

75Ω 75Ω

FM ANTENNA B

AM

AM ANTENNA

FM ANTENNA A

GND

RESET

REMOTE

LINE OUT

L

R

CONTROL

q w e r t y

REAR PANEL

q FM antenna terminals A/B (75 ohms)

Connect an external FM antenna with a coaxial cable, or
a cable network FM source.

w AM antenna and ground terminals

Connect the supplied AM loop antenna. Use the
terminals marked “AM” and “GND”. The supplied AM
loop antenna will provide good AM reception in most
areas. Position the loop antenna until you hear the best
reception.

ENGLISH

t RESET switch

Press this switch gently with the tip of a ballpoint pen or
similarly thin object if the tuner does not respond to a
button on the front panel. (See page 11.)

y Power cable

Connect the cable to a household power outlet (230V
AC).

e LINE OUT (analog output) connectors

The audio signals are output from these connectors.

r

REMOTE CONTROL connector

Using the supplied remote control connecting cord, this
connector enable this unit to be connected to a Marantz
component equipped with remote control connectors.
This connection make it possible to control an entire
system that centers on the amplifier or other such
component.

5

ENGLISH

PHONO TAPE 2AUXTUNER TAPE 1

CD

L

R

L

R

SPEAKER SYSTEMS 1

SPEAKER SYSTEMS 2

L R

REMOTE

CONT.

OUT

IN

AC OUTLETS

AC 120V 60HZ

SYSTEM 1: MINIMUM 8 OHMS

L R

SYSTEM 2: MINIMUM 8 OHMS
SYSTEM 1 AND 2: MINIMUM 16 OHMS

SWITCHED

1.0 A 120W
MAX

UNSWITCHED

1.0 A 120W
MAX

OUT

IN

OUT

IN

RCA Pin Plug Cord
(Provided)

RCA Pin Plug Cord
(Provided)

To AC Outlet

Stereo Amplifier

Tuner

AM(MW)Indoor Loop Antenna
(provided)

Roof-top FM Antenna(75 ohms)

Matching
Transformer
(optional)

Lead-type FM Antenna(75 ohms)
(provided)

AM(MW)Outdoor Antenna
5 to 12m

75‰ 75‰

FM ANTENNA B

AM

AM ANTENNA

FM ANTENNA A

GND

RESET

REMOTE

LINE OUT

L

R

CONTROL

CAUTION:

Do not plug the power cord of any
component into AC outlets and do not
turn their POWER switches on until
connections have been performed.

Note

Connect the tuner to other equipment in the below sequence to use the tuner.

1. Connect an FM antenna to the FM ANTENNA A terminal.

2. Connect an AM loop antenna to the AM ANTENNA terminals. The terminals do not have a particular polarity.

3. Connect the LINE OUT and REMOTE CONTROL connectors to their corresponding terminals on a stereo amplifier using

4. Plug the power cable of the tuner into a power outlet.

5. This completes connections. Point the antennas in a direction of good reception.

CONNECTIONS

the provided cords. (Turn power to the stereo amplifier OFF before making the connections.)

7

Assembling the AM loop antenna

1. Take out the connection

line.

2. Bend the base part in the

reverse direction.

3. Insert the hook at the

bottom of the loop part into
the slot at the base part.

4. Place the antenna on a

stable surface.

6

Note

• Do not plug in the mains cord until all connections have
been completed.

• When making connections, also refer to the operating
instructions of the other components.

• Be sure to connect the left and right channels properly
(left with left, right with right).

• Note that binding pin-plug cords together with mains cords
or placing them near a power transformer will result in
generating hum or other noise.

• Even if an external AM antenna is used, do not disconnect
the AM loop antenna.

• Make sure AM loop antenna lead terminals do not touch
metal parts of the panel.

OPERATIONS

FM/AM TUNER ST6001

ANTETTA

IF BAND

FM

ON/STAMDBY

POWER

STANDBY

WIDE

NARROW

AB

RDS

TIMER SET

BAND

ON/OFF

FM MODE

PRESETUPDOWN

UP

DOWN

TUNING

MEMONEXT

CANCEL

TUNING
MODE

/DISPLAY

ST.NAME

TIME ADJ.

TIMER

DAILY ONCE

TUNED STEREO RDS

PTY PT TP TA

PRESET

kHz
MHz

CH

MEMO

ui !1

!4

!5 !7

MEMORY PRESETTING

7

Manual operation

For example: presetting FM 90.1 MHz, to Preset number. 10

1. Select the FM by using the BAND button !7.

2. Tune to 90.1 MHz by using the TUNING 5∞ button i.

3. Press the MEMO button !1 briefly (for less than 0.5

second) Then, “MEMO” will blink in the display.

4. Select the preset number by using the PRESET 5∞

button !4.

5. MEMO button !1 pushed again, 90.1 MHz (broadcast

station) was able to be memorized in number 10 by this.

Note

Be sure to select the antenna A or B memorization when
you preset manual memory in FM broadcast.

7

Automatic operation

1. Select the desired broadcasting (FM, AM, or LW) by

using the BAND button !7.

2. Press the MEMO button !1 slightly longer than 1.5

second does.
Then, broadcasting will be automatically received, and

as many broadcasting station are received well will be
memorized preset number-01 after another.

3. Check the broadcasting station by using the PRESET

5∞ button !4.

Note

• In the case of FM automatic presetting, the antenna A, B
selector is set to “A” automatically,

And the broadcasting station is scanned twice. The
stations that have stronger broadcasting signal are preset
in the first time.; weaker ones are preset in the second
time.

• If a new broadcasting station is preset into a channel the
broadcasting station which has been preset into that
position area will be automatically erased.

• In mountainous or remote area broadcasting stations
which have weak broadcasting signals cannot be
automatically preset into the memory.

• Max. 30 broadcasting stations each for FM, AM(MW and
LW) bands can be preset.

LISTENING TO RADIO

1. Select FM, AM, or LW by using the BAND button !7.

2. Tune to the desired broadcast by using the TUNING i

or PRESET 5∞ button !4.

3. FM broadcasting is set up to “STEREO” mode

If the broadcasting signal is weak, or if there is a large
amount of interference in FM stereo broadcast, change
the monaural mode by presetting the FM MODE button
!5.

4. Select the IF BAND (FM bandwidth)

Select the NARROW bandwidth by pressing this button if
the broadcast signal is interfered with adjacent
broadcast in the FM .

FINE, MANUAL TUNING

This function used for selection the manual tuning of the fine
tuning mode.
Fine tuning mode is available only in the FM mode.

1. Press the TUNING MODE button u.

2. Every time you press this button, the following will be

displayed FINE ⇔ MANUAL.

7

In FINE (Tuning) mode

When you try press the TUNING 5∞ button i, the
frequency will be selected by 10 kHz step to ±50 kHz.
Then, it will automatically be set to the MANUAL mode in 4
second.

7

In MANUAL (Tuning) mode

1. Press the TUNING 5∞ button i in the FM band, then

the frequency will be selected by 50 kHz step.

2. In the MW band, the frequency will be selected by 9 kHz

step.

3. In the LW band, the frequency will be selected by 1 kHz

step.

ENGLISH

7

ENGLISH

DAILY

DAILY

DAILY

DAILY

TUNED STEREO

MHz

TIMER

DAILY

TUNED STEREO

MHz

DAILY

OPERATIONS

ADJUSTING CURRENT TIME

1. Press the TIME ADJ button t. Then “Hour display”

indicator will blink.

blink

2. The hour is set with the TUNING 5∞ button i.

3. Press the NEXT button !0. Then “minute display”

indicator will blink.

blink

4. The minute is set with the TUNING 5∞ button i.

blink

5. Press the NEXT button !0. The current time is set.

Note

• In the event of a power failure or when the AC mains cord
is disconnected, you must readjust the clock.

4. Preset the OFF time by the TUNING 5∞ button i and

the NEXT button !0.
(Same as operation of time adjust)

5. Press the NEXT button !0. The timer setting is

completed.

* Daily timer makes the system turn on and off at preset

times every day.

* If you want to record at ON time, select the desired

source with the input selector deck to the REC
position.

* If the timer indicator “TIMER” is off, the daily timer

doesn’t work.

7

Checking the daily timer

* If you want to check the daily timer, press the TIMER

SET button !3 at first. The ON time setting will be
displayed in the clock indicator. And, press the TIMER
SET button !3 again. The OFF time setting will be

displayed. Finally press TIMER SET button !3 once
again. It returns to the normal display.

DAILY TIMER

Example: presetting ON time: 7:15 OFF time: 9:30

1. Press the TIMER SET button !3.

2. Preset the ON time by the TUNING 5∞ button i and

the NEXT button !0.
(Same as operation of time adjust)

3. If ON time setting OK, Press the NEXT button !0.

7

Canceling the daily timer

* While setting the daily timer, if the cancel button is

held depressed, the timer function will be canceled.

Note

To temporarily cancel the daily timer, press the (Timer)
ON/OFF button !2. The ON time and OFF time settings

are retained in memory.

8

TUNED STEREO

PRESET

MHz

CH

TUNED STEREO

PRESET

MHz

CH

TUNED STEREO

PRESET

MHz

CH

TUNED STEREO

PRESET

MHz

CH

PRESET CH

MHz

OPERATIONS

FM/AM TUNER ST6001

ANTETTA

IF BAND

FM

ON/STAMDBY

POWER

STANDBY

WIDE

NARROW

AB

RDS

TIMER SET

BAND

ON/OFF

FM MODE

PRESETUPDOWN

UP

DOWN

TUNING

MEMONEXT

CANCEL

TUNING

MODE

/DISPLAY

ST.NAME

TIME ADJ.

TIMER

DAILY ONCE

TUNED STEREO RDS

PTY PT TP TA

PRESET

kHz

MHz

CH

MEMO

ty o!0

!2 !3

i!1

FILING (STATION NAME, ETC. )

For example: FM 98.8 MHz Preset CH-10 Station name
BBC1

1. Select the preset number 10 in the preset mode.

2. Press the ST.NAME/DISPLAY button y long pushed

(for more than 1.5 second)

Then, “_ _ _ _” will be displayed in the clock indicator.

blink

3. Select “B” with the TUNING 5∞ button i.

blink

4. Press the NEXT button !0 and then, the cursor will move

one space.

blink

5. After selecting “BBC 1” with the TUNING 5∞ i and the

NEXT button !0, press the MEMO button !1. The

broadcasting station name will be changed to “BBC 1”.

• Station names can be selected from 103 available
alphabetic letters and numbers.

• To cancel station name input, press and hold the
CANCEL button o.

7

Canceling preset stations

1. Call the station to cancel.

2. Press the MEMO button !1. “MEMO” will blink on the

display.

3. Press and hold press the CANCEL button o. The

selected station will be canceled from the preset
number.

RDS (RADIO DATA SYSTEM)

1. What is RDS?

RDS provides such indication as station names, local
times, and the types of program, the radio text ,etc. as
well as FM broadcasting.

2. You can receive the following kinds of data with this

RDS.

* PS (Program Service Name): displays FM station

names.

* CT (Clock Time): displays the information about times

provided from the station.

* PTY (Program Type): Program type will be displayed

while receiving FM broadcasting.

* RT (Radio Text): displays the news of stations

composed of up to 64 symbols.
* TP (Traffic Program)
* TA (Traffic Announcement)

The data is displayed in PTY mode as follows:

3. There are 29 programme categories:

NEWS News service

AFFAIR Politics and current events

INFO Special informative reports

SPORT Sports

EDUCATE Learning and continuation of education

DRAMA Radio plays, literature

CULTURE Culture and society

SCIENCE Programmes about sciences and

technology

OTHERS Variety

POP Pop music

ROCK Rock music

MOR Middle of the road music, ’easy-listening’

LIGHT Light classical music

CLASSIC Serious classical music

OTHER Other music

WEATHER Weather reports, forecasts

FINANCE Financial reports, commerce, trading

CHILDREN Children’s programmes

SOCIAL A Social affairs

RELIGION Religious programmes

PHONE IN Programmes in which the public

expresses its view by phone.

TRAVEL Travel reports

HOBBIES Programmes concerning recreational

activities

JAZZ Jazz music

COUNTRY Country music

NATION M National music

OLDIES Music from the so-called ‘golden age’ of

popular music

FOLK M Folk music

DOCUMENT Documentaries

• If you do not receive PTY Data, “NO PTY” will be

displayed.

9

ENGLISH

ENGLISH

FM/AM TUNER ST6001

ANTETTA

IF BAND

FM

ON/STAMDBY

POWER

STANDBY

WIDE

NARROW

AB

RDS

TIMER SET

BAND

ON/OFF

FM MODE

PRESETUPDOWN

UP

DOWN

TUNING

MEMONEXT

CANCEL

TUNING

MODE

/DISPLAY

ST.NAME

TIME ADJ.

TIMER

DAILY ONCE

TUNED STEREO RDS

PTY PT TP TA

PRESET

kHz

MHz

CH

MEMO

!6

!4

i !0

OPERATIONS

RDS DISPLAY

1. Select the FM band. RDS can be received only in FM.

2. Select the RDS broadcasting by using the TUNING 5∞

button i.
Then, RDS will light up in the upper side of the FTD

display. And the related data, if received, will be
displayed in the type of received data (PTY, RT, TP, TA)

3. RDS

1) The default of the RDS mode is PS.

2) Press the RDS button !6.
Each time you press the button briefly (1.5 second or

less), the modes will change as follows

PS →→PTY →→RT →→TA →→CT →→PS

3) PS mode

– When you select the PS with the RDS button !6, “PS”

will blink for about 4 seconds.

– After 4 seconds, PS or a station name entered by

manual file will be displayed.

4) PTY mode

– When you select the PTY with the RDS button !6,

PTY will blink for about 4 seconds, the type of
received PTY will be displayed.

– If there is no PTY data among received broadcasting,

RDS mode will be switched to PS mode
automatically.

5) RT mode

– When you select the RT with the RDS button !6, “RT”

will blink for about 4 seconds, After 4 seconds, the
data received broadcasting, the RDS mode will be
automatically switched to the PS mode.

6) TA mode (TP search function)

– When you select the TA with the RDS button !6, “TA”

will blink for about 4 seconds, TP received
broadcasting will be searched with the FM frequency
increasing in 50 kHz steps.

– If TP received broadcasting is searched, the increase

in frequency will be stop and it is asked whether TA
will be received or not.

– If TP and TA turn off while you are receiving the TA,

the tuner will search the TA broadcasting again with
the FM frequency increasing in 50 kHz steps.

7) CT mode

– When you select the CT with the RDS button !6, “CT”

will blink for about 4 seconds. After 4 seconds, the
clock time together with the frequency will be
displayed. “CT” can be received regardless of
whichever RDS mode. The tuner is set to.

* Not to use CT mode,

1. Press and hold the RDS button !6 for longer than 8

seconds, and press briefly the RDS button !6 within 0.5
seconds.

– The indicator will be changed as follows:

PS →→PTY →→RT →→TA →→(NO CT) →→PS

– In this mode, although “CT ” data are entered, the

time is not changed to the current time.

2. In ”NO CT“ mode, press and hold the RDS button !6 for

longer than 8 seconds.

– The indicator will be changed as follows:

PS →→PTY →→RT →→TA →→CT

3. PTY Search

1) Press the RDS button !6 for longer then 1.5 second.
Then “SEARCH” will be shown in the display.

2) Select the desired PTY mode by using the PRESET
5∞ button !4.

3)

– If you press the NEXT button !0, the PTY mode wills

blink in the clock display.

– Searching will start when you push the TUNING 5∞

button i.

– When the PTY mode that you have selected is

searched, searching will stop and the PTY mode will
be displayed.

– If there is no program in the PTY mode, you have

selected, searching will stop at the frequency started.

10

TROUBLESHOOTING

RESET

REMOTE

LINE OUT

L

R

CONTROL

If your Tuner should not perform as expected, consult the table below to see if the problem can be corrected before seeking
help from your dealer or our service organization.

ENGLISH

Symptom

No sound

Only noise is heard

Broadcasting is received but
with noise

•

INPUT SELECTOR of amplifier is not
Select “TUNER” in INPUT SELECTOR.

• Volume of amplifier positioned in
“MIN.”

• The terminal for system connection is

pullet out.

• The antenna is pulled out.

•

The frequency is not detected exactly.

•

The position of antenna is not suitable.

• The power of CD player is turned on.

Cause

OTHERS

7

WHEN TO USE RESET SWITCH

• When this system is subjected to an electrical shock.

• When the power is irregular.

In the above cases, function buttons may not often
operate or the display may operate wrongly. In these
cases, try the following:

— Rear panel —

RESET SWITCH

Measures

• Set to “TUNER”.

• Adjust Volume accordingly.

• Connection correctly.

• Connect the antenna on the rear

panel.

• Set the frequency correctly.

• Install the antenna again after

locating the best reception position.

• Turn off CD player.

If the equipment becomes heavily soiled:
– dilute some washing up liquid in water, in a ratio of one

part detergent to six parts water;

– dip a soft, lint free cloth in the solution and wring the cloth

out until it is damp;

– wipe the equipment with the damp cloth;
– dry the equipment by wiping it with a dry cloth.

Page

–

–

6

6

7

6

–

Press the RESET switch lightly once or twice with a pencil
or a ballpoint pen.

7

CARE AND MAIN TENANCE

This section describes the care and maintenance tasks that
must be performed to optimize the operation of your
Marantz equipment.

7

CLEANING OF EQUIPMENT
EXTERNAL SURFACES

The exterior finish of your ST6001 will last indefinitely with
proper care and cleaning. Never use scouring pads, steel
wool, scouring powders or harsh chemical agents (e.g., lye
solution), alcohol, thinners, benzine, insecticide or other
volatile substances as these will mar the finish of the
equipment. Likewise, never use cloths containing chemical
substances. If the equipment gets dirty, wipe the external
surfaces with a soft, lint-free cloth.

7

REPAIRS

Only the most competent and qualified service technicians
should be allowed to service your unit. Marantz and its
factory trained warranty station personnel have the
knowledge and special equipment needed for the repair and
calibration of this precision instrument.

In the event of difficulty, call the proper toll-free telephone
number listed on the face of the warranty to obtain the name
and address of the Marantz Authorized Service Center
nearest you. In many cases, the dealer where you
purchased your Marantz unit may be equipped to provide
service. Please include the model, serial number of your unit
together with a copy of your purchase receipt and a full
description of what you feel is abnormal in its behaviour.

Memory backup

In case a power outage occurs or the power cord is
accidentally unplugged, the ST6001 is equipped with a
backup function to prevent memory data such as the
preset memory from being erased.
The memory funcitons are backed up for up to about
one week.

11

ENGLISH

FM/AM TUNER ST6001

ANTETTA

IF BAND

FM

ON/STAMDBY

POWER

STANDBY

WIDE

NARROW

AB

RDS

TIMER SET

BAND

ON/OFF

FM MODE

PRESETUPDOWN

UP

DOWN

TUNING

MEMONEXT

CANCEL

TUNING
MODE

/DISPLAY

ST.NAME

TIME ADJ.

TIMER

DAILY ONCE

TUNED STEREO RDS

PTY PT TP TA

PRESET

kHz
MHz

CH

MEMO

11.0

311.5

2.5

298.0

83

97

14.0

440.0

(mm)

SPECIFICATIONS & DIMENSIONAL DRAWINGS

FM section

Frequency range .........................87.5 MHz to 108.0 MHz

50 kHz steps: Manual mode
(10 kHz steps: Fine mode)

Sensitivity (S/N: 30 dB)...........................................1.2 µV

Total harmonic distortion (1 kHz)

Mono ................................................................0.08 %

Stereo...............................................................0.15 %

Signal to Noise ratio

Mono: .................................................................80 dB

Stereo:................................................................75 dB

Selectivity (±400 kHz)

Wide mode.........................................................65 dB

Narrow mode......................................................80 dB

Frequency Response ......20 Hz to 15 kHz (+1.0, -3.0 dB)

Image Rejection.......................................................70 dB

AM Suppression ......................................................55 dB

Stereo Separation (1 kHz) .......................................50 dB

MW Section

Frequency range .........522 kHz to 1620 kHz (9 kHz step)

Sensitivity (S/N: 20 dB) ..................................50 dBµV /m

Signal to Noise ratio.................................................50 dB

Total harmonic distortion..........................................1.0 %

Image Rejection.......................................................35 dB

LW Section

frequency range ............146 kHz to 290 kHz (1 kHz step)

Sensitivity (S/N: 20 dB) ..................................57 dBµV /m

Signal to Noise ratio.................................................45 dB

Total harmonic distortion..........................................1.0 %

Image Rejection.......................................................35 dB

General

Power supply...........................................AC 230 V 50 Hz

Power consumption .................................................8.6 W

Weight .....................................................................4.0 kg

Accessories

Audio connection cord.....................................................1

AM loop antenna.............................................................1

FM indoor antenna..........................................................1

Remote control connection cord .....................................1

User Guide......................................................................1

Registration Card ............................................................1

* For purposes of improvement, specifications and design

are subject to change without notice.

12

www.marantz.com

You can find your nearest authorized distributor or dealer on our website.

EUROPE Marantz Europe B.V. P.O. Box 8744, 5605 LS Eindhoven, The Netherlands

is a registered trademark.

Printed in China 01/2006 00M02CW851310 mzh-d