Read the following information before using the service manual.
What you can do with this manual
Search for a Ref. No. (phrase)
(Ctrl+Shift+F)
You can use the search function in Acrobat Reader to
search for a Ref. No. in schematic diagrams, printed
wiring circuit diagrams, block diagrams, and parts
lists.
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the set is defective.
Be sure to test for leakage current with the AC plug in both polarities, in addition, when the set's power is in each state
(on,offandstandbymode),ifapplicable.
CAUTION
Please heed the following cautions and instructions during servicing and
inspection.
◎Heed the cautions!
Cautions which are delicate in particular for servicing
are labeled on the cabinets, the parts and the chassis,
etc. Be sure to heed these cautions and the cautions
described in the handling instructions.
Check that all screws, parts and wires removed or
disconnected when servicing have been put back in their
original positions, check that no serviced parts have
deteriorate the area around. Then make an insulation
check on the external metal connectors and between
the blades of the power plug, and otherwise check that
safetyisensured.
(Insulationcheckprocedure)
Unplug the power cord from the power outlet, disconnect
the antenna, plugs, etc., and on the power. Using a 500V
insulation resistance tester, check that the insulation
If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the
set is defective.
z1 The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product
Logo are registered trademarks of the Wi-Fi Alliance.
1 – 13 ch (for N)
n
Bluetooth Version 2.1 + EDR
Maximum 2.5 mW (Class 2)
Approx. 32.8 ft/10 m in line of sight
2.4 GHz band
FHSS (Frequency-Hopping Spread Spectrum)
A2DP 1.2 (Advanced Audio Distribution Prole)
For purposes of improvement, specications and design are subject to
change without notice.
(for N) : AC 230 V, 50 Hz / 60Hz
DIMENSION
Unit: in. (mm) Weight: 22 lb 8 oz (10.2 kg)
17 21/64 (440)
(32)
1 17/64
14 7/32 (361)
16 3/16 (411)
(18)
45/64
7 9/32 (185)
6 47/64 (171)
9 23/32 (247)
(12)
15/32
(40)
1 37/64
15 7/16 (392)
10 33/64 (267)
(53)
2 3/32
(20)
25/32
1 31/32 (50)
13 25/64 (340)
2 23/64
(60)
9
(14)
35/64
1 31/32 (50)
PRECAUTIONS DURING SERVICE
Initializing This Unit
Initialize this unit if you have replaced the microcomputer, one of the parts around the microcomputer, or the digital PCB.
1. Press the power button to turn off the power.
2. Hold down buttons "
3. Release the buttons after conrming that the display ashes in intervals of approximately 1 second.
* The unit is initialized.
MOVIE
" and "
MUSIC
" at the same time and press the power button to turn on the power.
:
• If the status in step 3 does not occur, start again from step 1.
• Initializing the device restores settings congured by the user to the factory settings. Take note of your settings beforehand
and recongure them after initialization.
MOVIE
MUSIC
X
Service Jigs
The following jigs (extension cable kit) are used when repairing the PCBs.
Order the jigs from your dealer if necessary.
8U- 110084S : EXTENSION UNIT KIT : 1 Set
8U- 110136S : EXTENSION UNIT KIT : 1 Set
(See 72 page)
10
DISASSEMBLY
• Remove each part in the order of the arrows below.
• Reassemble removed parts in the reverse order.
• Read before reassembling removed parts.
• If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing
the work. Failure to shape the wires correctly may cause problems such as noise.
FRONT PANEL ASSY
See ""
1. FRONT PANEL ASSY
and ""
FRONT PCB
(Ref. No. of EXPLODED VIEW : C5)
HEAD PHONE PCB
(Ref. No. of EXPLODED VIEW : C2)
FRONT SWE PCB
(Ref. No. of EXPLODED VIEW : C1)
FRONT HDMI PCB
(Ref. No. of EXPLODED VIEW : C3)
GUIDE FFC1 PCB
(Ref. No. of EXPLODED VIEW : C11)
FRONT HDMI FFC CABLE PCB
(Ref. No. of EXPLODED VIEW : C7)
RADIATOR ASSY
See ""
2. RADIATOR ASSY
and ""
H-DAM PCB
(Ref. No. of EXPLODED VIEW : C10)
GUIDE PCB
(Ref. No. of EXPLODED VIEW : C9)
TOP COVER
DIGITAL PCB ASSY
See ""
3. DIGITAL PCB ASSY
and ""
DIGITAL PCB
(Ref. No. of EXPLODED VIEW : C37)
GUIDE FFC2 PCB
(Ref. No. of EXPLODED VIEW : C36)
CX870MIDDLE PCB
(Ref. No. of EXPLODED VIEW : C39)
CX870MODULE
(Ref. No. of EXPLODED VIEW : C40)
VIDEO PCB ASSY
See ""
4. VIDEO PCB ASSY
and ""
VIDEO PCB
(Ref. No. of EXPLODED VIEW : C35)
INPUT PCB ASSY
See ""
5. INPUT PCB ASSY
and ""
INPUT PCB
(Ref. No. of EXPLODED VIEW : C30)
SMPS PCB
See ""
7. SMPS PCB
and ""
SMPS PCB
(Ref. No. of EXPLODED VIEW : C22)
MAIN TRANS
See ""
8. MAIN TRANS
and ""
TRANS,POWER
(Ref. No. of EXPLODED VIEW : C21)
XLR PCB ASSY
See ""
6. XLR PCB ASSY
and ""
XLR PCB
(Ref. No. of EXPLODED VIEW : C16)
FRONT CNT PCB
(Ref. No. of EXPLODED VIEW : C13)
SIDE CNT PCB
(Ref. No. of EXPLODED VIEW : C14)
FUSE PCB
(Ref. No. of EXPLODED VIEW : C12)
11
• The angles from which the photos are taken are shown by ":".
• See the diagram below about the shooting direction of each photograph.
• Photographs with no shooting direction indicated were taken from the top of the unit.
• The photograph is AV7702U model.
(Shooting direction:X)[View from the top]
↓Shooting direction: B↓
Front side
Shooting
direction: D
Shooting
direction: C
↑Shooting direction: A↑
12
1. FRONT PANEL ASSY
(1) Remove the screws.
(2) Cut the wire clamp, then remove the connector wires and FFC. Remove the screws.
→
View from the bottom
Front side
CN602
CUT
CN916
FFC
FFC
CN914
13
2. RADIATOR ASSY
(1) Remove the screws.
(2) Cut the wire clamp. Remove the screws.
→
→
View from the bottom
CUT
(3) Cut the wire clamp, then remove the connector wires.
CN481
CN482
CN920CN922CN484 CN483
CN921CN923
CN940
14
3. DIGITAL PCB
(1) Remove the screws.
(2) Cut the wire clamp, then remove the connector wires and FFC.
→
STYLE PIN
→
CX870 ONLY
(3) Remove the connector.
BN23A
CN903
FFC
STYLE PIN
BN24ABN25ABN21ABN26A
FFC
Front side
CN916
CON1
CON2
CN914
CN901
BN27A
15
4. VIDEO PCB
(1) Remove the connector.
5. INPUT PCB
→
BN28B
BN27B
→
→
BN21B
(1) Remove the connector.
From HDAM PCB
CN482
→
BN24C BN26C
BN64C
BN23C
→
From HDAM PCB
CN481
→
From HDAM PCB
CN484
→
From HDAM PCB
CN483
16
6. XLR PCB
→
→
(1) Remove the screws.
(2) Remove the connector wire.
CN481
CN482
View from the bottom
CN920CN922CN484 CN483
→
CN921CN923
→
CN940
→
→
(3) Remove the connector wire. Remove the screws.
CN940
CN941
7. SMPS PCB
→
See "EXPLODED VIEW" for instructions on how to remove each PCB of the "".
→
→
8. TRANS POWER
→
→
→
See "EXPLODED VIEW" for instructions on how to remove each PCB of the "".
17
SPECIAL MODE
Special Mode Conguration Buttons
No. 1 - 11, 14 : Hold down buttons"A", "B" and "C" at the same time and press the power button to turn on the power.
b
No. 12, 13 : Hold down buttons "A" and "B" for at least 3 seconds while the power is on.
b
No. 15 : Press the "A" and "B" buttons simultaneously while inserting the AC plug to turn the power on.
b
Version Display
1
(u-COM / DSP Error Display)
User Initialization Mode
(Settings for the Installer Setup are not
2
initialized.)
Factory Initialization Mode
(Initialization includes settings for the
3
Installer Setup.)
PANEL / REMOTE LOCK Selection ModeBACKENTER-
4
Check the Video/Audio pass
5
Mode
Protection History Display Mode↑↑-
6
232C Standby Clear Mode :↑↑-
7
Operation Info Mode↑↑-
8
TUNER STEP mode
9
(U and N model only)
Installer Setup Mode
10
Protection Pass Mode
11
(No Protection Mode this unit)
CX870 / CY920 Initialization modeBACKENTER-
12
CX870 / CY920 Reboot modeM-DAX
13
USB Update ModeHDMI OUTSTATUS
14
Forced USB All Device Write ModeHDMI OUTSTATUS-
15
DIMMERSTATUS-
GAMEA-DSX-
MOVIEMUSIC-
ZONE
SELECT
↑↑-
CURSOR
0
M-DAX
BACK-
BACK-
DYNAMICEQDYNAMIC
DYNAMIC
EQ
Displays the version of rmware such as the main rmware or DSP,
etc. Errors that have occurred are displayed.
(See 19 page)
Initializes backup data.
(Settings for the Installer Setup are not initialized.)
Initializes backup data.
(Initialization includes settings for the Installer Setup.)
Start this unit in the PANEL/REMOTE LOCK selection mode so that
PANEL LOCK and Remote Lock can be selected as ON or OFF.
(See 23 page)
This is a special mode for service conrmation used during repair
work to simplify the conrmation work for the Audio channel/video channel. (See 25 page)
Displays the protection occurrence history.
(See 68 page)
Switches from 232C standby mode to normal standby mode.
(See 68 page)
Displays the total operating time of the set, number of times the
power was switched on, and number of occurrences of each protection.(See 69 page)
Enables reception STEP of the ANALOG TUNER to be changed.
(See 70 page)
Access the Remote Maintenance mode via the internet. Installer
Setup is displayed on Setup menu / Network.
Refer to AVR_RemoteMaintenance_.pdf of SDI.
b
Enables the power to be turned on when protection detection is in
VOL
the stopped state.
Enter this mode only after replacing Flash for CX870 / CY920 and
rewriting the rmware.
(See 71 page)
-Reboot the CX870 / CY920(See 71 page)
Switches this unit to USB Update mode.
(See 75 page)
Mode used when this unit cannot be recovered.
Forcibly switches this unit to USB update mode.
(See 77 page)
When the volume indicator displays "", the set has entered a special mode for developers.
In this case, RS-232C communication cannot be used.
To cancel this special mode, press and hold the "
tor returns to the normal display, RS-232C communication can be used.
DYNAMIC
EQM-DAX
X
MOVIE
MUSIC
CURSOR
DYNAMIC
A-DSX
GAME
VOL
"and "
f
STATUS
HDMI
OUT
18
" buttons for 3 seconds and longer. When the volume indica-
BACKENTER
STATUS
DIMMER
0
ZONE
SELECT
1. Version Display Mode
1.1. Actions
Version information is displayed when the device is started in this mode.
1.2. Starting up
Hold down buttons "
Press the "
A version list is also displayed on GUIs while the version appears on the display.
b
STATUS
DIMMER
" button after this to show the information in section 1.3 on the display.
1.3. Display Order
Error information(See "") → q Model destination information, Serial Number
→ w Firmware Package Version → e Main µ-com, Main 1st Boot Loader Version
→ r Sub µ-com, Sub 1st Boot Loader Version → t DSP1/2/3/4 ROM → y Audio, Video PLD → u GUI SFLASH
→ i Ethernet 1st Boot Loader, Hardware ID → o Ethernet 2nd Boot Loader, Rhapsody Flag → Q0 Ethernet IMAGE
→ Q1 Ethernet MAC ADDRESS information → Q2 BT MAC ADDRESS information → Q3 MultEQ Pro APP (Displayed when Audyssey Pro is complete) → Q4 HD Radio (For U Region) → Q5 MultEQ Pro ICL (Displayed when Audyssey Pro is complete)
Model destination information, Serial Number :
q
A V7 70 2U*
" and "
STATUS
" at the same time and press the power button to turn on the power.
Case of CX870 : Display "*" at the end
Firmware Package Version :
w
Main µ-com, Main 1st Boot Loader Version :
e
Sub µ-com, Sub 1st Boot Loader Version : Model code
r
t
DSP 3/4 ROM :
X
DSP 1/2 ROM :
A V7 70 2N*
S /N .* ** ** ** ** *
F ir m.Pa ck ag e
V er .: ** **
M ai n: ** .* **
M ai nF BL:* *. **
S ub: XX YZ ** **
S ubFB L: ** .* *
: Model code Y : Model Z : Region(E3=1, E2=2, E1C=5)
D SP 1: ** .* *
D SP 2: ** .* *
D SP 3: ** .* *
D SP 4: ** .* *
Case of CX870 : Display "*" at the end
Case of CX870 : Display "*" at the end
Audio, Video PLD :
y
A ud ioPL D: ** .* *
V id eoPL D: ** .* *
19
GUI SFLASH :
u
i
AA:Hardware ID
o
Q0
Q1
Ethernet 1st Boot Loader, Hardware ID :
Ethernet 2nd Boot Loader, Rhapsody Flag :
Ethernet IMAGE :
Ethernet MAC ADDRESS information :
G UI: XX YZ ** **
X
: Model code Y : Model Z : Region(E3=1, E2=2, E1C=5)
E th er ne tF BL
* ** ** *- AA
E th er ne tS BL
* ** ** ** ** ** ** -B B
E th er ne tI MG
* ** ** ** ** ** **
* NE TM ACAd dr es s
* ** ** ** -* ** **
BT MAC ADDRESS information :
Q2
MultEQ Pro APP :
Q3
HD Radio (For U Region) :
Q4
Software Congration
*
Release Typte
X
Base Version No.
Y
Build No.
Z
MultEQ Pro ICL :
Q5
* BTMA CAD DR ES S
* ** ** *- ** ** *S
* Mu lt EQPr oAP P
* *. ** .* *. ** **
* HD: ** ** ** ** -
* Mu lt EQPr oIC L
* *. ** .* *. ** **
X YY YY .Z ZZ
20
1.4. Error display
See the table below for descriptions of displayed errors and countermeasures for these.
Display order is q,w,e,r,t,y,u.
The model name, brand name and region
information written in the rmware are
compared to the region settings in the
PCB.This error is displayed if the informa-
q
Firm Check
NG
w
SUB μ -COM NGThere is not a reply from SUBμ-COM.
e
IP SCALER NG
r
GUI Serial
Flash NG
t
DIR NG
y
DSP NG
u
EEPROM NG
tion does not match.
" ▲ " is displayed as the rst character
if the rmware is not correct (see right
section of table).
An error occurs in Loopback Test of the
DDR memory to perform at initial setting
of i/p Scaler(ADV8003).
In initial setting of i/p Scaler ( ADV8003 ),
there is not the reply of the Loopback Test
result of the DDR memory .
In initial setting of i/p Scaler ( ADV8003 ),
there is not the reply of the Loopback Test
result of the DDR memory .
" ▼ " is displayed as the rst character of
the GUI rmware version
This error is displayed if there is no response from the DIR.
The DSP* FLAG0 port does not enter "Hi"
status even after executing a DSP reset
during a DSP code boot.
The DSP* FLAG0 port does not enter "Hi"
status before issuing a DSP command.
ACK="Hi" does not occur during DSP*
data reading, even when WRITE="Lo".
ACK="Lo" does not occur during DSP*
data reading, even when REQ="Lo".
ACK="Hi" does not occur during DSP*
data writing, even when WRITE="Hi".
ACK="Lo" does not occur during DSP*
data writing, even when REQ="Lo".
An error occurred in a checksum of the
EEPROM(*** is a block address number).
F I R ME R R O R
–
M a i n: * * . * *
–
D S P 1: * * . * *
–
A u d i oP L D : * * . * *
–
G U I: * * * * * * * *
S U BE R R O R0 1
I PS C A L E RE R R0 1
I PS C A L E RE R R0 2
G U IV E R .E R R O R
•
G U I: * * * * * * * *
D I RE R R O R0 1
D S P *E R R O R0 1
D S P *E R R O R0 2
D S P *E R R O R0 3
D S P *E R R O R0 4
D S P *E R R O R0 5
D S P *E R R O R0 6
E 2 P R O ME R R * * *
• Check the resistor for
setting region(R1589 /
R1590, DIGITAL PCB).
• Write the rmware for
the correct region.
• Check the SUB(IC171)
and surrounding circuits.
• Check the circuits
around the IP SCALER
(IC401, DIGITAL PCB)
and DDR2 (IC402/
IC403).
If there appear to be
no problems, IC401 or
IC402/IC403 is faulty.
• Check the rmware
version.
• Check the DIR (IC202,
DIGITAL PCB) and
surrounding circuits.
• Check the DSP (IC251,
IC261, IC271, IC281
DIGITAL PCB) and
surrounding circuits.
21
1.5. Version Display in the Setup Menu
Follow the steps below to display the rmware information.
(1) Press the "
SETUP
" button on the remote control.
(2) Select "".
The version information is displayed as a 14-digit number as shown in the screen shot below.
General/Firmware
Version
Displays system information
XXXX-XXXX-XXXX-XX
This 14-digit number comprises part of the version number of each device and module.
These version numbers correspond to the 12-digit number as shown below.
The 2nd digit from the right for Main
The 1th digit from the right for Main
The 2nd digit from the right for Sub
The 1st digit from the right for Sub
Main
Sub
DSP1
DSP2
DSP3
DSP4
A.PLD
V.PLD
GUI
E.FBL
E.SBL
E.IMG
X
8X 38-3 8 21
X X X 0 0 2 8
X X X
X X X
X X X
X X X
X X X
X X X
2
3
4
5
1
7
X X X X 0 0 1 6
The 1st digit from the right for DSP1
The 1st digit from the right for DSP2
The 1st digit from the right for DSP3
The 1st digit from the right for DSP4
The 1st digit from the right for A.PLD
The 1st digit from the right for V.PLD
The 1st digit from the right for GUI
X X X X X X
XBX X X X X X X X X X X
XIX X X X X X X 0 0 3 7
Info display2 3 4- 6 7 7 3 - 0 5
The 1st digit from the right for IMG
The 2nd digit from the right for IMG
The rmware version numbers and this 14-digit version information are written in the Service Information.
b
22
2. PANEL / REMOTE LOCK Selection Mode
2.1. Actions
Turn the PANEL LOCK and REMOTE LOCK modes on and off.
2.2. Starting up
Hold down buttons "
Select the mode using the button "
BACK
2.3. Displaying and Selecting Each Mode
The information shown on the display changes each time the button "
Press the button "
The On/Off setting for each mode is shown by an asterisk "*".
q
The buttons on the unit and the master volume knob cannot be operated.
w
The buttons on the unit cannot be operated.
e
The PANEL LOCK mode is turned off.
r
The device cannot be operated by the remote control.
t
The REMOTE LOCK mode is turned off.
ENTER
" to set the currently displayed mode and restart the device.
– FP /V OLLO CK *O n
F PL OC KO n
F P/ VO LL OC K* On
– FPLO CKOn
F PL OC K* On
– FPLO CKOf f
F PL OC KO ff
– RCLO CKOn
R CL OC KO n
– RCLO CKOf f
" and "
ENTER
" at the same time and press the power button to turn on the power.
CURSOR f/
", and press the button "
d
ENTER
CURSOR f/
" to commit the selection.
" is pressed.
d
23
3. Selection Modes for Service-related Operations
3.1. Actions
Select diagnostic mode (service path check mode), protection history display mode, or 232C standby clear mode.
3.2. Starting up
Hold down buttons "
Select the mode using the button "
ZONE SELECT
CURSOR f/
3.3. Displaying and Selecting Each Mode
The information shown on the display changes each time the button "
Press the button "
q
Service Path Check Mode:
The Video and Audio paths can be checked.
This function is convenient for conrming problem paths in the product and executing a path
w
The protection history can be checked.
e
Switches from 232C standby mode to normal standby mode.
r
Operation Info for the unit can be checked.
t
Enables reception STEP of the ANALOG TUNER to be changed.
ENTER
" to set the currently displayed mode and restart the device.
– 1. SE RV IC EC HE CK
2 .P RO TE CT IO N
check after repair.
1 .S ER VI CECH EC K
– 2. PR OT EC TI ON
2 .P RO TE CT IO N
– 3. RS 23 2CRE SE T
3 .R S2 32 CR ES ET
– 4. OPIN FO
4 .O PI NF O
– 5. TU NE RF RQSE T
" and "
BACK
" at the same time and press the power button to turn on the power.
", and press the button "
d
ENTER
CURSOR f/
" to commit the selection.
" is pressed.
d
3.3. Canceling the mode
Press the power button to turn off the power.
24
3.5. DIAGNOSTIC MODE (Service Path Check Mode)
3.5.1. Actions
This function is convenient for conrming problem paths in the product and executing a path check after repair.
The Video and Audio paths can be checked.
The backup data is not rewritten.
3.5.2. Starting up
Hold down buttons "
Select "
The "
1. SERVICE CHECK
TUNED
STERO
", "
ZONE SELECT
" and press the "
RDS
" and "
BACK
" and "
" at the same time and press the power button to turn on the power.
ENTER
" button to start the diagnostic mode.
" segments are lit in this mode.
3.5.3. Canceling diagnostic mode
Press the power button to turn off the power.
3.5.4. Selecting items
Press q button to switch between video items and audio items.
Press button w or e to select the previous or next item.
Paths conrmation itemDisplay SettingsContents of conrmation Remarks
Analog
(MAIN ZONE)
1
Digital
(MAIN)
2
Digital (signal) Path
(ZONE2)
3
Digital (signal) Path
(ZONE3)
4
HDMI
5
g.01
g.02a
g.02b
g.03a
g.03b
g.03c
g.04a
g.04b
g.05a
g.05b
g.05c
A 0 1 : A N A L O GP A S S
A 0 2 : D I G I T A L
A 0 3 : D I G I T A L - Z 2
A 0 4 : D I G I T A L - Z 3
A 0 5 : H D M I
Input Source : CBL/SAT
Input Mode : Analog xed
Sound mode :Direct
Vol : 60(-20dB)
Amp assign : 11.1ch
MAIN ZONE ON
ZONE2 OFF
ZONE3 :OFF
Input Source : CBL/SAT
Input Mode : DIGITAL xed
Sound mode : Multi Ch Stereo
Vol : 60(-20dB)
Amp assign : 11.1ch
Speaker Select : Floor
Speaker Conog : All Speaker=Small/Subwoofer=2spkrs
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : Online Music
Input Mode : Auto
Sound mode : Stereo
Z2 Vol : 60(-20dB)
Amp assign : 11.1ch
MAIN ZONE : ON
ZONE2 : ON
ZONE3 : OFF
Input Source : Online Music
Input Mode : Auto
Sound mode : Stereo
Z3 Vol : 60(-20dB)
Amp assign : 11.1ch
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : ON
Input Source : CBL/SAT
Input Mode : HDMI xed
Sound mode : Stereo
Vol : 60(-20dB)
Amp assign : 11.1ch
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
(bThe input source can be switched to any source except CBL/SAT.)
25
Paths conrmation itemDisplay SettingsContents of conrmation Remarks
Analog A/D
MAIN ZONE:
6
Analog Amp Assign
(Amp Assign:ZONE2)
7
Analog Amp Assign
(Amp Assign:ZONE3)
8
Amp Assign
(Amp Assign:BiAMP-Surround Back)
9
Amp Assign
(Amp Assign:BiAMP-Front Wide)
10
Amp Assign
(Amp Assign:BiAMP-Height)
11
Front Height
12
g.06a
g.06b
g.07
g.08
g.09
g.10
g.11
g.12a
g.12b
A 0 6 : A D
A 0 7 : A S S I G N - Z 2
A 0 8 : A S S I G N - Z 3
A 1 1 : B i A M P - S B
A 1 1 : B i A M P - F W
A 1 1 : B i A M P - H 1
A 1 4 : F R O N TH E I G H T
Input Source : CBL/SAT
Input Mode : Analog xed
Sound mode : Multi Ch Stereo
Vol : 60(-20dB)
Amp assign : 11.1ch
Height Speakers=2 Height Speakers
Height Layout= Front Height
Speaker Select : Floor
Speaker Cong : All Speaker=Small/Subwoofer=2spkrs
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : Stereo
Amp assign : 11.1ch
MAIN ZONE : ON
ZONE2 : ON
Z2 Source : Source
Z2 Vol : 60(-20dB)
ZONE3 : OFF
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : Stereo
Amp assign : 11.1ch
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : ON
ZONE3 Source : Source
Z3 Vol. : 60.0(-20.0dB)
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : Stereo
Vol : 60(-20dB)
Amp assign : 9.1ch (Bi-Amp)
Preout for Bi-Amp : SURROUND BACK
MAIN ZONE ON
ZONE2 OFF
ZONE3 OFF
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : Stereo
Vol : 60(-20dB)
Amp assign : 9.1ch (Bi-Amp)
Preout for Bi-Amp : FRONT WIDE/HEIGHT 2
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : Stereo
Vol. : 60.0(-20.0dB)
Amp assign : 9.1ch (Bi-Amp)
Preout for Bi-Amp : HEIGHT1
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : Multi Ch Stereo
Vol. : 60.0(-20.0dB)
Amp assign : 11.1ch
Height Speakers : 4Height Speakers
Height Layout : Top Front & Top Rear
WIDE/HEIGHT2 XLR = Front Wide(AV7702 Only)
Speaker Cong : Front Wide=None
Speaker Select : Floor & Height
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
・Analog input ⇒ RCA output (Front L/R, Center, Surround L/R, Surround Back L/R, Front Wide L/R)
・ Analog input ⇒ XLR output, SW(20Hz) (Front L/R, Center, Surround L/R, Surround Back L/R, Front Wide L/R, Subwoofer)
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
・Analog input ⇒ ZONE2 RCA output(ZONE2 L/R)
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
・Analog input ⇒ ZONE3 RCA output (ZONE3 L/R)
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
・Analog input ⇒ RCA output (Front L/R and Surround Back L/R)
・Analog input ⇒ XLR output (Front L/R and Surround Back L/R)
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
・Analog input ⇒ RCA output (Front L/R and Front Wide/Height2 L/R)
・Analog input ⇒ XLR output (Front L/R and Front Wide/Height2 L/R)
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
・Analog input ⇒ RCA output (Front L/R and Height1 L/R)
・Analog input ⇒ XLR output (Front L/R and Height1 L/R)
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
・Analog input ⇒ RCA output (Height1 L/R → Top Front L/R, Height2 L/R → Top Rear L/R)
・Analog input ⇒ XLR output (Height 1 L/R → Top Front L/R)
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
26
Paths conrmation itemDisplay SettingsContents of conrmation Remarks
Front Wide
13
7.1 CH Path
14
Back DAC>>Height2
15
Height1 DAC>>Height2
16
g.13a
g.13b
g.14
g.15a
g.15b
g.16a
g.16b
A 1 5 : F R O N TW I D E
A 1 9 : 7 . 1 C HI N
A 2 0 : S B - H E I G H T 2
A 2 1 : H 1 - H E I G H T 2
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : Multi Ch Stereo
Vol. : 60.0(-20.0dB)
Amp assign : 11.1ch
Height Speakers : 4 Height Speakers
Height Layout : Front Height & Top Middle
Speaker Conog : S.Back=None
Speaker Select : Floor
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
Input Mode : 7.1Ch In
Vol. : 60.0(-20.0dB)
Amp assign : 11.1ch
Speaker Conog : All Speaker=Small/Subwoofer=2spkrs
Speaker Select=Front, Center, Surround, S.Back, Subwoofer
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : Multi ch Stereo
Vol. : 60.0(-20.0dB)
Amp assign : 11.1ch
Height Speakers : 4Height Speakers
Height Layout : Top Front & Top Rear
Speaker Conog : Surround Back=None
Speaker Select=Floor & Height
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : Multi ch Stereo
Vol. : 60.0(-20.0dB)
Amp assign : 11.1ch
Height Speakers : 4Height Speakers
Height Layout : Top Front & Top Rear
Speaker Conog : All Small
Speaker Select=Front
Wide/Height2 XLR = Front Wide(AV7702 Only)
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
・Analog input ⇒ RCA output ((Height 2 L/R → Top Front L/R)
(bThe input source can be switched to any source except CBL/SAT.)
(bVolume -20dB is the value when Relative settings are used. The value is 60 when Absolute settings are used)
Attention:In A21 mode, sound of Height1 will be output from the RCA / XLR of Height2.
(No sound will be output from the RCA / XLR of Height1)
27
3.5.6. Video system conrmation items
g. XX : See the block diagram of the g.XXth.
Paths conrmation itemDisplay SettingsContents of conrmation Remarks
Analog Video
1
Video Convert
(Analog or HDMI ⇒ HDMI)
2
HDMI pass
(MAIN ZONE)
3
HDMI CEC
4
(Control Monitor:HDMI Monitor1)
HDMI Audio
(Audio :AVR)
5
HDMI Audio
(Audio :TV)
6
GUI
7
HDMI
(ZONE2)
8
g.17
g.18a
g.18b
g.19
g.20
g.21a
g.21b
g.21c
g.22a
g.22b
g.23
g.24
V 0 1 : V I D E OP A S S
V 0 2 : V . C O N V E R T
V 0 3 : H D M IP A S S
V 0 4 : H D M IC E C
V 0 5 : H . A U D I O - A V R
V 0 6 : H . A U D I O - T V
V 0 7 : G U IM E N UO N
V 0 8 : Z O N E 2H D M I
Input Source : CBL/SAT
Video Convert(IP Scaler) : OFF, All sources
MAIN ZONE : ON
ZONE2 : ON
ZONE3 : OFF
Input Source : CBL/SAT
Video Convert(IP Scaler) : ON, All sources
IP Scaler : "Analog & HDMI", All sources
Resolution : "Auto", All sources
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
Source of Video Convert(IP Scaler) : OFF, All sources
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
HDMI Control : ON
Control Monitor:Monitor1(HDMI Monitor Out1)
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
HDMI Control : OFF
HDMI Audio:AVR ( if checking the audio output from AVR )
Input Source : CBL/SAT
HDMI Control : OFF
HDMI Audio:TV ( if checking the audio output from TV )
Input Source : CBL/SAT
Video Convert(IP Scaler) : ON, All sources
IP Scaler : "Analog & HDMI", All sources
Resolution : "AUTO", All sources
Setup Menu : ON
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
ZONE2 Source : Source
MAIN ZONE : ON
ZONE2 : ON
ZONE3 : OFF
・Component input ⇒ Component output
(bThe input source can be switched to any source except CBL/SAT.)
・CVBS input ⇒ IP Scaler ⇒ HDMI output.
・Component input ⇒ IP Scaler ⇒ HDMI output.
・HDMI input ⇒ IP Scaler ⇒ HDM output.
・ETHERNET input ⇒ IP Scaler ⇒ HDMI output.
(bThe input source can be switched to any source except CBL/SAT.)
・HDMI input ⇒ HDMI input(MAIN ZONE)
(bThe input source can be switched to any source except CBL/SAT.)
・ When the power supply of a TV is put in the standby mode, make sure that the power supply of this unit is also put in the
standby mode.
・The ARC path can also be checked (check this using the TV input source).
(bThe input source can be switched to any source except CBL/SAT.)
The port No. is Changed same as AVRX4100 (M S Lee)
MAINZON E2ZONE3
CBL/SAT
DVD
PHONO
V.AUX
TUNER
DAZ2L61
DAZ2R60
DAZ3L59
DAZ3R58
DAFL57
DAFR56
MONO
MIX
MONO
MIX
MIC
CD
BD
MP
32
29
31
33
1
4
2
3
32
29
31
33
1
4
2
3
HPF
MONO
MIX
HPF
HPF
MONO
MIX
HPF
78,79
74,75
70,71
72,73
76,77
82.83
64,65
66,67
62,63
OPEN
88,89
ADC
53,54
Z2
46,47
Z3
32,33
ZONE3
TONE
VOL IC
NJW1194V
TONE
ZONE2
TONE
VOL IC
NJW1194V
TONE
R2A15220
92
93
94PREOU T_FL
95
97
DA_BUS
38
39
40
41
36
37
MAIN_FL
42
90
MAIN_FR
43
91
EXT_FR
38
92
EXT_SW
39
93
EXT_SW
41
EXT_BU S
40
94
36
96
37
EXT_SR
97
DAASSIGN2L
PREOUT _FL
DAASSIGN2R
PREOUT _FR
DAASSIGN3L
DAASSIGN3R
PREOUT _FR
DAASSIGN1L
PREOUT _FL96
45
EXT_SBL
DAASSIGN1R
PREOUT _FR
44
EXT_SBR
AV7702 ANALOG AUDIO BLOCK
DAFL
EXT_FL
DAFR
DASW1
DASW2
DARSV
DAC
EXT_C
DASL
EXT_SL
DASR
FL_VOL
TONE
FR_VOL
TONE
SW1_VOL
SW2_VOL
C_VO L
SL_VO L
SR_VOL
R2A15220
TONE
TONE
FWL_VO L
FWR_VOL
FHL_VO L
FHR_VOL
SBL_V OL
SBR_V OL
16
PREOUT _FWL
14
PREOUT _FWR
10
PREOUT _FHL
11
8
PREOUT _FHR
7
100
PREOUT _S
99
2
PREOUT _SBR
3
20
PREOUT _FL
19
22
PREOUT _FR
23
16
PREOUT _SW1
14
PREOUT _SW2
10
11
8
PREOUT _C
7
100
PREOUT _SL
99
2
PREOUT _SR
3
20
19
22
23
PREOUT _FL
PREHP_FL
PREOUT _FL
PREHP_FR
BL
73 P REOUT Z3L
7274PREOUT Z3R
75
PREOUT Z2L
PREOUT Z2R
76
77
PREOUT _FL
PREOUT _FR
PREOUT _SW1
PREOUT _SW2
PREOUT _C
PREOUT _SL
PREOUT _SR
PREOUT _SBL
PREOUT _SBR
PREOUT _FWL
PREOUT _FWR
PREOUT _FHL
PREOUT _FHR
PREHP_FL
PREHP_FR
ZONE3ZONE2MA IN
HDAM PA RT
AMPIN_ FL/FR
32,33
AMPIN_ FWL/FWR
46,47
OPEN
53,54
AMPIN_ SBL/SBR
88,89
RY871
RY881
RY882
RY883
RY884RY885RY886
Balanced OUT
PREOUT
ATT.
FL
FR
SW1
SW2
C
SL
SR
SBL
SBR
FW_L
FW_R
H1_L
H1_R
H2_L
H2_R
ZONE2 L
ZONE2 R
ZONE3 L
ZONE3 R
HPL
HPR
GND
FL
FR
SW1
SW2
C
SL
SR
SBL
SBR
FWL
FWR
H1_L
H1_R
H/P OUT
61
fig.21b
OPT1 (TV)
OPT2 (CD)
COAX1( CBL/SAT)
COAX2( DVD)
DIGTA L IN
ANT1
ANT2
USB
ETHERNET
RJ-45 wit h Transformer
HDMI BLOCK
Z2HDMISP DIF
USBD-
USBD+
RX+/-
TX+/-
920VD0~7
920PCK
to MAIN DIR #28
RXMCK/DSD MCK
RXBCK/DS DBCK
RXLRCK/DSD 5
RXI2S0/DSD1
RXI2S1/DSD2
RXI2S2/DSD3
RXI2S3/DSD4
RXSPDIF/DSD0
RXINT0
TO SubC PU #17
TXB
CK
TXLRCK
TXI2S0
Z2_HAINT
OPT.0
#33
OPT.1
#32
COAX.0
#37
COAX.1
#35
CY920
NETWORKED MEDIA
MODULE
IPOD AUTH.
23671011050AS
(MFI337S3959)
A2
A4
B3
B4
C2
C3
C4
B1
D4
K1
K2
L1
E1
SERIAL FLASH
256M
MX25L25635FMI- 10G
AV7702 DIGITAL AUDIO BLOCK
Z3DIRSPDI F
ZONE3
DIR
(To Z3 DAC #10)
(To MA IN DIR)
BCOSPD IF
to MAIN DIR #31
BCOMC K
BCOBC K_SCK
BCOLRC K
BCODAT A_DSDL
BCODSDR
DEMPZ3
(From/To SubCPU)
(To MainC PU)
LC89091JA-H
#77(SubCPU) , N4(V.PLD)
#75(SubCPU)
#74(SubCPU) , P3(V.PLD)
L6 (To V.PL D)
TDO1_TDI 2
SUBTC K
SUBTDI
P3
M5
J1
J2
H1
H2
K3
#73
#32
#72
#33
APLDDI
APLDCK
APLDCS
Z3PLDAERR
Z2PLDAERR
SUBTM S
2
L6
L2
G
N4
G1
M1
66
#26
#71
F1
PLDAERR
E3
13591011123
Z3DIRBC K
Z3DIRMCK
F16
Z3DIRLRCK
F15
G16
AUDIO PLD
5M570ZF256C5N
Z3DIRDAT A
G15
DEMPZ2
(To Z2 DAC #10)
4
Z3DIRPERR
Z3DIRnPC M
G14
H14
LC89091JA-H
13591011123
Z2DIRSPDI F
ZONE2
DIR
Z2DIRBC K
Z2DIRLRCK
Z2DIRMCK
H16
H15
Z2DIRDAT A
Z2DIRPERR
Z2DIRnPC M
J16
J15
J14
COAX.0
COAX.1
OPT.0
OPT.1
BCOSPD IF
Z2HDMISP DIF28
4
HDMISPDI F
J12
L16
24.576MHz
37
35
MAIN
33
32
31
30,29
DIR
PCM9211PTR
789
10
52019181721
DIRAUXDAT A
DIRAUXLRC K
DIRAUXBC K
DIRAUXMC K
DIRXMCK
L15
K14
K15
K16
H12
DIRRST
#29
DIRCE
#21
DIRDIN
DIRDOUT
DIRCLK
15
16
3426242325
14
13
12
11
DIRDATA
DIRBCK
DIRLRCK
DIRMCK
N15
DIRPERR
DIRnPCM
L13
L14
N16
M16
M15
P5
N5
P4
P7
P2
R1
N1
N3
P6
N2
M2
M3
R16
R12
P12
N12
R14
T15
T12
R13
P13
T13
M13
N14
N13
M14
DATAAD
DIRSLRCK
DIRSBCK
DIRSMCK
#78
#82
#81
#80
(From SubCPU )
DACMCK
DACBCK
DACLRCK
DZF1
DACPCM F
DACPCM CSW1
DACPCM SW2RSV
DACPCM S
DACMCK
DACBCK
DACLRCK
DZF2
DACASSIGN1
DACASSIGN2
DACASSIGN3 (SR7009/AV7702)
Z2DACMC K
Z2DACB CK
Z2DACLRC K
Z2DACDAT A
Z2DACMU TE
DEMPZ2
(From Z2 D IR #6)
Z3DACMC K
Z3DACB CK
Z3DACLRC K
Z3DACDAT A
Z3DACMU TE
DEMPZ3
(From Z3 D IR #6)
CSCKIN
CSCKO UT
CSREFIN
CSCLOC K
DACRST
DACMS
DACMDI
DACMC
(From/To SubCPU)
#30
#23
#24
#6
ADCRST
(From SubCPU )
9
10
12
11
15
22
20
21
MAIN DAC1
14
7
6
16
11
10
8
9
15
22
20
21
14
MAIN DAC2
7
6
16
10
9
8
12
13
15
14
17
10
12
13
15
14
17
10
5
JITTER REDUCER
3
7
CS210010-CZZR
4
13
ADC
AK5358BET
PCM1690
PCM1690
ZONE2
DAC
PCM5100
ZONE3
DAC
PCM5100
2
1
31
32
29
30
35
36
33
34
43
44
41
42
39
40
37
38
35
36
33
34
39
40
37
38
43
44
41
42
SR7009/AV7702 ONLY
6
7
6
7
ADINL
ADINR
DAFL
DAFR
DAC
DASW1
DASW2
DARSV
DASL
DASR
DAASSIGN1L
DAASSIGN1R
DAASSIGN2L
DAASSIGN2R
DAASSIGN3L
DAASSIGN3R
DAZ2L
DAZ2R
DAZ3L
DAZ3R
ANALOG AUDIO BLOCK
C6A6C7C8A8
DSP1INMCK
DSP1INBCK
927597
A7B5B8
DSP1INLRCK
DSP1INLR
DSP1INF_FL
DSP1INSWC_C
DSP1INS_SL
95
103
100
ADSP21487KSWZ-4B(400MHz)
25MHz25MHz25MHz
A3V56S40G TP-60
A5
B6
C5
DSP1FLAG3
DSP1INRSV_ FR
DSP1INSB_ SR
DSP1INRSV_ SW
74
7755989986947388899687
101
138
DSP1OUT F
DSP1OUT BCK
DSP1OUT CSW
DSP1OUT LRCK
1st DSP
DSPMOSI (#51)
DSPMISO (#52)
DSPICLK (#53)
FLASHSDRAM
16M256M
MX25L1606EM2I-12G
B9
A10
A12
C11
DSP2OUT F
DSP2OUT CSW
DSP2OUT BCK
DSP2OUT LRCK
DSP2INMCK
927597
95
74
77
76
DSP1OUT S
DSP1OUT SB
DSP1OUT FH
DSP1OUT FW
DSP1OUT RSV2
DSP1OUT RSV1
55
76
101
103
DSP2INS
DSP2INSB
DSP2INFH
DSP2INRSV1
DSP2INRSV2
DSP2INCSW
DSP2INFW_SW
100
DSP2INF
DSP2INLRCK
98998694738889
DSP2INBCK
2nd DSP
ADSP21487KSWZ-4B(400MHz)
17354134
DSP1RST
DSP1CS
DSP1FLAG0
DSP1FLAG3
#87
#86
#84
#85
(From/To SubCPU)(From/To SubCPU)(From/To SubCPU)
A3V56S40G TP-60
256M
DSPMOSI (#51)
DSPMISO (#52)
DSPICLK (#53)
MX25L1606EM2I-12G
SERIAL FLASHSDRAM
16M
A11A9C10
DSP2OUT S
11
B10
B
D11
DSP2OUT SB
DSP2FLAG3
DSP2OUT FH
DSP2OUT FW
96
DSP3INMCK
138
ADSP21487KSWZ-4B(400MHz)
17354134
DSP2RST
DSP2CS
DSP2FLAG0
DSP2FLAG3
#90
#79
#88
#89
B16
A15
E15
B14
D12
DSP3INBCK
DSP3INLRCK
DSP3INF
927597878677767374
A13
D16
C15
DSP3INSB
DSP3INCSW
DSP3INFH
DSP3INS
256M
A3V56S40G TP-60
B13
E16
E13
B1255
DSP3OUT BCK
DSP3OUT LRCK
DSP3INRSV1
DSP3INFW
98
99
3rd DSP
DSPMOSI (#51)
D
SPMISO( #52)
DSPICLK (#53)
SERIAL FLASHSDRAM
MX25L1606EM2I-12G
D15
F13
DSP3OUT F
DSP3OUT CSW1
10389100
16M
62
T5
P10
R9
P11
D14
D13
E14
F14
C14
C1395
TFH
DSP3OUT SB
DSP3OU
DSP3OUT FW
DSP3OUT RSV1
DSP3OUT S
948896
DSP3FLAG3
138
T4R7P9R5T6R6T7R8T8
DSP4INBCK
DSP4INMCK
927597878677767374
DSP4INSB
DSP4INLRCK
DSP4INF
DSP4INCSW
DSP4INS
T9P8T11
T1055
DSP4OUT F
DSP4OUT BCK
DSP4OUT LRCK
DSP3INRSV1
DSP4INFH
DSP4INFW
98
99
R4
DSP4OUT CSW1
10389101
R10
R11
DSP4OUT SW2RSV
DSP4OUT S
100
DSP4OUT SB
DSP4OUT FH
948896
R395
DSP3OUT RSV1
DSP4OUT FW
DSP4FLAG3
138
4rd DSP
17354134
DSP3RST
#92
ADSP21487KSWZ-4B(400MHz)
DSP3CS
#93
25MHz
DSP3FLAG0
#95
A3V56S40G TP-60
256M
DSPMOSI (#51)
DSPMISO (#52)
DSPICLK (#53)
SERIAL FLASHSDRAM
MX25L1606EM2I-12G
16M
17354134
DSP3RST
DSP3CS
DSP3FLAG0
#91
#83
#98
(From/To SubCPU)
fig.21C
AV7702 HDMI VIDEO BLOCK
HDMI I N1
(CBL/SA T)
HDMI I N2
(DVD)
HDMI I N3
(BLU- RAY)
HDMI I N4
(GAME)
HDMI I N5
(MEDIA Player)
HDMI I N6
(AUX2)
HDMI I N7
(CD)
HDMI I N8
(AUX1)
P3 RX
P2 RX
P1 RX
P0 RX
HDMI SW2(MN864777)
AD8195
Buffer
MAIN
SUB
27.000MHz
P0 TX
P1 TX
P3 RX
P2 RX
P
1 RX
P0 RX
HDMI SW1(MN864777)
MAIN
SUB
105
119
27.000MHz
P0 TX
P1 TX
P1 RX
P0 RX
P3 RX
P2 RX
HDMI Rx
Matrix SW
RXI2S0~3, RXSPD IF
RXMCK, RXB CK, RX
TXDATA 0
TXBCK , TXLRCK
LRCK, RXIN T0
HDMI TX(MN864777)
600MHz
Rxlink0Txlink0
4K/2K
Up Scaler
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
Txlink1
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
600MHz
4K/2K
600MHz
4K/2K
HDMI Tx
Matrix SW
27.000MHz
P1 TX
P0 TX
ARC
HDMI ZO NE2
HDMI O UT1
HDMI O UT2
ANALOG
VIDEO BLOCK
Z2_HAINT
Z2HDMISP DIF
RXI2S0~3, RXSPD IF
RXMCK, RXB CK, RXLRCK, R XINT0
TXDATA 0
TXBCK , TXLRCK
DEC_Y_IN
DEC_PB_IN
DEC_PR_IN
DEC_CVB S_IN
ADV7850
VIDEO INPUT
27.000MHz
920VD0~7
920PCK
VIDEO PLD
EPM570F256C4N
WITH TMDS
PCK/HSYN C/VSYNC/DE
VIDEO SIGNAL OUT
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
B0~B7 /G0~G7/R0~R7
AD55/058Z-0(ADV8003-8B)
Video Processor(1080P, OSD, IP Conv,)
CONTROL
S. FLASH
MX25L12845EMI-10G
128M
DDR2 SDRAM
A3R12E40CBF-8EA3R12E40CBF-8E
512M
DDR2 INTERFACE
DDR2 SDRAM
512M
27.000MHz
920VD0~7
920PCK
DIGITAL AUDIO BLOCK
63
fig.22a
OPT1 (TV)
OPT2 (CD)
COAX1( CBL/SAT)
COAX2( DVD)
DIGTA L IN
ANT1
ANT2
USB
ETHERNET
RJ-45 wit h Transformer
HDMI BLOCK
Z2HDMISP DIF
USBD-
USBD+
RX+/-
TX+/-
920VD0~7
920PCK
to MAIN DIR #28
RXMCK/DSD MCK
RXBCK/DS DBCK
RXLRCK/DSD 5
RXI2S0/DSD1
RXI2S1/DSD2
RXI2S2/DSD3
RXI2S3/DSD4
RXSPDIF/DSD0
RXINT0
TO SubC PU #17
TXB
CK
TXLRCK
TXI2S0
Z2_HAINT
OPT.0
#33
OPT.1
#32
COAX.0
#37
COAX.1
#35
CY920
NETWORKED MEDIA
MODULE
IPOD AUTH.
23671011050AS
(MFI337S3959)
A2
A4
B3
B4
C2
C3
C4
B1
D4
K1
K2
L1
E1
SERIAL FLASH
256M
MX25L25635FMI- 10G
AV7702 DIGITAL AUDIO BLOCK
Z3DIRSPDI F
ZONE3
DIR
(To Z3 DAC #10)
(To MA IN DIR)
BCOSPD IF
to MAIN DIR #31
BCOMC K
BCOBC K_SCK
BCOLRC K
BCODAT A_DSDL
BCODSDR
DEMPZ3
(From/To SubCPU)
(To MainC PU)
LC89091JA-H
#77(SubCPU) , N4(V.PLD)
#75(SubCPU)
#74(SubCPU) , P3(V.PLD)
L6 (To V.PL D)
TDO1_TDI 2
SUBTC K
SUBTDI
P3
M5
J1
J2
H1
H2
K3
#73
#32
#72
#33
APLDDI
APLDCK
APLDCS
Z3PLDAERR
Z2PLDAERR
SUBTM S
2
L6
L2
G
N4
G1
M1
66
#26
#71
F1
PLDAERR
E3
13591011123
Z3DIRBC K
Z3DIRMCK
F16
Z3DIRLRCK
F15
G16
AUDIO PLD
5M570ZF256C5N
Z3DIRDAT A
G15
DEMPZ2
(To Z2 DAC #10)
4
Z3DIRPERR
Z3DIRnPC M
G14
H14
LC89091JA-H
13591011123
Z2DIRSPDI F
ZONE2
DIR
Z2DIRBC K
Z2DIRLRCK
Z2DIRMCK
H16
H15
Z2DIRDAT A
Z2DIRPERR
Z2DIRnPC M
J16
J15
J14
COAX.0
COAX.1
OPT.0
OPT.1
BCOSPD IF
Z2HDMISP DIF28
4
HDMISPDI F
J12
L16
24.576MHz
37
35
MAIN
33
32
31
30,29
DIR
PCM9211PTR
789
10
52019181721
DIRAUXDAT A
DIRAUXLRC K
DIRAUXBC K
DIRAUXMC K
DIRXMCK
L15
K14
K15
K16
H12
DIRRST
#29
DIRCE
#21
DIRDIN
DIRDOUT
DIRCLK
15
16
3426242325
14
13
12
11
DIRDATA
DIRBCK
DIRLRCK
DIRMCK
N15
DIRPERR
DIRnPCM
L13
L14
N16
M16
M15
P5
N5
P4
P7
P2
R1
N1
N3
P6
N2
M2
M3
R16
R12
P12
N12
R14
T15
T12
R13
P13
T13
M13
N14
N13
M14
DATAAD
DIRSLRCK
DIRSBCK
DIRSMCK
#78
#82
#81
#80
(From SubCPU )
DACMCK
DACBCK
DACLRCK
DZF1
DACPCM F
DACPCM CSW1
DACPCM SW2RSV
DACPCM S
DACMCK
DACBCK
DACLRCK
DZF2
DACASSIGN1
DACASSIGN2
DACASSIGN3 (SR7009/AV7702)
Z2DACMC K
Z2DACB CK
Z2DACLRC K
Z2DACDAT A
Z2DACMU TE
DEMPZ2
(From Z2 D IR #6)
Z3DACMC K
Z3DACB CK
Z3DACLRC K
Z3DACDAT A
Z3DACMU TE
DEMPZ3
(From Z3 D IR #6)
CSCKIN
CSCKO UT
CSREFIN
CSCLOC K
DACRST
DACMS
DACMDI
DACMC
(From/To SubCPU)
#30
#23
#24
#6
ADCRST
(From SubCPU )
9
10
12
11
15
22
20
21
MAIN DAC1
14
7
6
16
11
10
8
9
15
22
20
21
14
MAIN DAC2
7
6
16
10
9
8
12
13
15
14
17
10
12
13
15
14
17
10
5
JITTER REDUCER
3
7
CS210010-CZZR
4
13
ADC
AK5358BET
PCM1690
PCM1690
ZONE2
DAC
PCM5100
ZONE3
DAC
PCM5100
2
1
31
32
29
30
35
36
33
34
43
44
41
42
39
40
37
38
35
36
33
34
39
40
37
38
43
44
41
42
SR7009/AV7702 ONLY
6
7
6
7
ADINL
ADINR
DAFL
DAFR
DAC
DASW1
DASW2
DARSV
DASL
DASR
DAASSIGN1L
DAASSIGN1R
DAASSIGN2L
DAASSIGN2R
DAASSIGN3L
DAASSIGN3R
DAZ2L
DAZ2R
DAZ3L
DAZ3R
ANALOG AUDIO BLOCK
C6A6C7C8A8
DSP1INMCK
DSP1INBCK
927597
A7B5B8
DSP1INLRCK
DSP1INLR
DSP1INF_FL
DSP1INSWC_C
DSP1INS_SL
95
103
100
ADSP21487KSWZ-4B(400MHz)
25MHz25MHz25MHz
A3V56S40G TP-60
A5
B6
C5
DSP1FLAG3
DSP1INRSV_ FR
DSP1INSB_ SR
DSP1INRSV_ SW
74
7755989986947388899687
101
138
DSP1OUT F
DSP1OUT BCK
DSP1OUT CSW
DSP1OUT LRCK
1st DSP
DSPMOSI (#51)
DSPMISO (#52)
DSPICLK (#53)
FLASHSDRAM
16M256M
MX25L1606EM2I-12G
B9
A10
A12
C11
DSP2OUT F
DSP2OUT CSW
DSP2OUT BCK
DSP2OUT LRCK
DSP2INMCK
927597
95
74
77
76
DSP1OUT S
DSP1OUT SB
DSP1OUT FH
DSP1OUT FW
DSP1OUT RSV2
DSP1OUT RSV1
55
76
101
103
DSP2INS
DSP2INSB
DSP2INFH
DSP2INRSV1
DSP2INRSV2
DSP2INCSW
DSP2INFW_SW
100
DSP2INF
DSP2INLRCK
98998694738889
DSP2INBCK
2nd DSP
ADSP21487KSWZ-4B(400MHz)
17354134
DSP1RST
DSP1CS
DSP1FLAG0
DSP1FLAG3
#87
#86
#84
#85
(From/To SubCPU)(From/To SubCPU)(From/To SubCPU)
A3V56S40G TP-60
256M
DSPMOSI (#51)
DSPMISO (#52)
DSPICLK (#53)
MX25L1606EM2I-12G
SERIAL FLASHSDRAM
16M
A11A9C10
DSP2OUT S
11
B10
B
D11
DSP2OUT SB
DSP2FLAG3
DSP2OUT FH
DSP2OUT FW
96
DSP3INMCK
138
ADSP21487KSWZ-4B(400MHz)
17354134
DSP2RST
DSP2CS
DSP2FLAG0
DSP2FLAG3
#90
#79
#88
#89
B16
A15
E15
B14
D12
DSP3INBCK
DSP3INLRCK
DSP3INF
927597878677767374
A13
D16
C15
DSP3INSB
DSP3INCSW
DSP3INFH
DSP3INS
256M
A3V56S40G TP-60
B13
E16
E13
B1255
DSP3OUT BCK
DSP3OUT LRCK
DSP3INRSV1
DSP3INFW
98
99
3rd DSP
DSPMOSI (#51)
D
SPMISO( #52)
DSPICLK (#53)
SERIAL FLASHSDRAM
MX25L1606EM2I-12G
D15
F13
DSP3OUT F
DSP3OUT CSW1
10389100
16M
64
T5
P10
R9
P11
D14
D13
E14
F14
C14
C1395
TFH
DSP3OUT SB
DSP3OU
DSP3OUT FW
DSP3OUT RSV1
DSP3OUT S
948896
DSP3FLAG3
138
T4R7P9R5T6R6T7R8T8
DSP4INBCK
DSP4INMCK
927597878677767374
DSP4INSB
DSP4INLRCK
DSP4INF
DSP4INCSW
DSP4INS
T9P8T11
T1055
DSP4OUT F
DSP4OUT BCK
DSP4OUT LRCK
DSP3INRSV1
DSP4INFH
DSP4INFW
98
99
R4
DSP4OUT CSW1
10389101
R10
R11
DSP4OUT SW2RSV
DSP4OUT S
100
DSP4OUT SB
DSP4OUT FH
948896
R395
DSP3OUT RSV1
DSP4OUT FW
DSP4FLAG3
138
4rd DSP
17354134
DSP3RST
#92
ADSP21487KSWZ-4B(400MHz)
DSP3CS
#93
25MHz
DSP3FLAG0
#95
A3V56S40G TP-60
256M
DSPMOSI (#51)
DSPMISO (#52)
DSPICLK (#53)
SERIAL FLASHSDRAM
MX25L1606EM2I-12G
16M
17354134
DSP3RST
DSP3CS
DSP3FLAG0
#91
#83
#98
(From/To SubCPU)
fig.22b
AV7702 HDMI VIDEO BLOCK
HDMI I N1
(CBL/SA T)
HDMI I N2
(DVD)
HDMI I N3
(BLU- RAY)
HDMI I N4
(GAME)
HDMI I N5
(MEDIA Player)
HDMI I N6
(AUX2)
HDMI I N7
(CD)
HDMI I N8
(AUX1)
P3 RX
P2 RX
P1 RX
P0 RX
HDMI SW2(MN864777)
AD8195
Buffer
MAIN
SUB
27.000MHz
P0 TX
P1 TX
P3 RX
P2 RX
P
1 RX
P0 RX
HDMI SW1(MN864777)
MAIN
SUB
105
119
27.000MHz
P0 TX
P1 TX
P1 RX
P0 RX
P3 RX
P2 RX
HDMI Rx
Matrix SW
RXI2S0~3, RXSPD IF
RXMCK, RXB CK, RX
TXDATA 0
TXBCK , TXLRCK
LRCK, RXIN T0
HDMI TX(MN864777)
600MHz
Rxlink0Txlink0
4K/2K
Up Scaler
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
Txlink1
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
600MHz
4K/2K
600MHz
4K/2K
HDMI Tx
Matrix SW
27.000MHz
P1 TX
P0 TX
ARC
HDMI ZO NE2
HDMI O UT1
HDMI O UT2
ANALOG
VIDEO BLOCK
Z2_HAINT
Z2HDMISP DIF
RXI2S0~3, RXSPD IF
RXMCK, RXB CK, RXLRCK, R XINT0
TXDATA 0
TXBCK , TXLRCK
DEC_Y_IN
DEC_PB_IN
DEC_PR_IN
DEC_CVB S_IN
ADV7850
VIDEO INPUT
27.000MHz
920VD0~7
920PCK
VIDEO PLD
EPM570F256C4N
WITH TMDS
PCK/HSYN C/VSYNC/DE
VIDEO SIGNAL OUT
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
B0~B7 /G0~G7/R0~R7
AD55/058Z-0(ADV8003-8B)
Video Processor(1080P, OSD, IP Conv,)
CONTROL
S. FLASH
MX25L12845EMI-10G
128M
DDR2 SDRAM
A3R12E40CBF-8EA3R12E40CBF-8E
512M
DDR2 INTERFACE
DDR2 SDRAM
512M
27.000MHz
920VD0~7
920PCK
DIGITAL AUDIO BLOCK
65
fig.23
AV7702 HDMI VIDEO BLOCK
HDMI I N1
(CBL/SA T)
HDMI I N2
(DVD)
HDMI I N3
(BLU- RAY)
HDMI I N4
(GAME)
HDMI I N5
(MEDIA Player)
HDMI I N6
(AUX2)
HDMI I N7
(CD)
HDMI I N8
(AUX1)
P3 RX
P2 RX
P1 RX
P0 RX
HDMI SW2(MN864777)
AD8195
Buffer
MAIN
SUB
27.000MHz
P0 TX
P1 TX
P3 RX
P2 RX
P
1 RX
P0 RX
HDMI SW1(MN864777)
MAIN
SUB
105
119
P0 TX
P1 TX
HDMI ZO NE2
P1 RX
HDMI TX(MN864777)
27.000MHz
P0 RX
HDMI Rx
P3 RX
27.000MHz
Matrix SW
600MHz
Rxlink0Txlink0
P2 RX
RXI2S0~3, RXSPD IF
RXMCK, RXB CK, RX
TXDATA 0
TXBCK , TXLRCK
LRCK, RXIN T0
4K/2K
Up Scaler
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
Txlink1
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
600MHz
4K/2K
600MHz
4K/2K
HDMI Tx
Matrix SW
P1 TX
P0 TX
ARC
HDMI O UT1
HDMI O UT2
ANALOG
VIDEO BLOCK
Z2_HAINT
Z2HDMISP DIF
RXI2S0~3, RXSPD IF
RXMCK, RXB CK, RXLRCK, R XINT0
TXDATA 0
TXBCK , TXLRCK
DEC_Y_IN
DEC_PB_IN
DEC_PR_IN
DEC_CVB S_IN
ADV7850
VIDEO INPUT
27.000MHz
920VD0~7
920PCK
VIDEO PLD
EPM570F256C4N
WITH TMDS
PCK/HSYN C/VSYNC/DE
VIDEO SIGNAL OUT
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
B0~B7 /G0~G7/R0~R7
AD55/058Z-0(ADV8003-8B)
Video Processor(1080P, OSD, IP Conv,)
CONTROL
S. FLASH
MX25L12845EMI-10G
128M
DDR2 SDRAM
A3R12E40CBF-8EA3R12E40CBF-8E
512M
DDR2 INTERFACE
DDR2 SDRAM
512M
27.000MHz
920VD0~7
920PCK
DIGITAL AUDIO BLOCK
66
fig.24
AV7702 HDMI VIDEO BLOCK
HDMI I N1
(CBL/SA T)
HDMI I N2
(DVD)
HDMI I N3
(BLU- RAY)
HDMI I N4
(GAME)
HDMI I N5
(MEDIA Player)
HDMI I N6
(AUX2)
HDMI I N7
(CD)
HDMI I N8
(AUX1)
P3 RX
P2 RX
P1 RX
P0 RX
HDMI SW2(MN864777)
AD8195
Buffer
MAIN
SUB
27.000MHz
P0 TX
P1 TX
P3 RX
P2 RX
P
1 RX
P0 RX
HDMI SW1(MN864777)
MAIN
SUB
105
119
27.000MHz
P0 TX
P1 TX
P1 RX
P0 RX
P3 RX
P2 RX
HDMI Rx
Matrix SW
RXI2S0~3, RXSPD IF
RXMCK, RXB CK, RX
TXDATA 0
TXBCK , TXLRCK
LRCK, RXIN T0
HDMI TX(MN864777)
600MHz
Rxlink0Txlink0
4K/2K
Up Scaler
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
Txlink1
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
600MHz
4K/2K
600MHz
4K/2K
HDMI Tx
Matrix SW
27.000MHz
P1 TX
P0 TX
ARC
HDMI ZO NE2
HDMI O UT1
HDMI O UT2
ANALOG
VIDEO BLOCK
Z2_HAINT
Z2HDMISP DIF
RXI2S0~3, RXSPD IF
RXMCK, RXB CK, RXLRCK, R XINT0
TXDATA 0
TXBCK , TXLRCK
DEC_Y_IN
DEC_PB_IN
DEC_PR_IN
DEC_CVB S_IN
ADV7850
VIDEO INPUT
27.000MHz
920VD0~7
920PCK
VIDEO PLD
EPM570F256C4N
WITH TMDS
PCK/HSYN C/VSYNC/DE
VIDEO SIGNAL OUT
B0~B7 /G0~G7/R0~R7
PCK/HSYN C/VSYNC/DE
B0~B7 /G0~G7/R0~R7
AD55/058Z-0(ADV8003-8B)
Video Processor(1080P, OSD, IP Conv,)
CONTROL
S. FLASH
MX25L12845EMI-10G
128M
DDR2 SDRAM
A3R12E40CBF-8EA3R12E40CBF-8E
512M
DDR2 INTERFACE
DDR2 SDRAM
512M
27.000MHz
920VD0~7
920PCK
DIGITAL AUDIO BLOCK
67
3.6. Protection History Display Mode
3.6.1. Actions
This mode records and displays an event in which the THERMAL, CURRENT, ASO or DC protection was activated.
If protections have been activated multiple times, the latest protection operation is recorded.
3.6.2. Starting up
Hold down buttons "
Select the "2. PROTECTION" using the button "
ZONE SELECT
" and "
BACK
" at the same time and press the power button to turn on the power.
CURSOR f/
", and press the button "
d
ENTER
" to commit the selection.
3.6.3. Protection information and displays
・Press the "
・The protection history can be checked.
(a) If no protections have occurred.
Note: No Protection History Display Mode this unit.
FLD
STATUS
L1
L2
" button in Protection History Display Mode.
P RO TE CTHI ST OR Y
: NOPR OT EC T
3.7. 232C Standby Clear Mode
3.7.1. Actions
Switches from 232C standby mode to normal standby mode.
3.7.2. Starting up
Hold down buttons "
Select the "3.RS232C RESET" using the button "
L1
FLD
L2
ZONE SELECT
2 .P RO TE CT IO N
– 3. RS 23 2CRE SE T
" and "
BACK
" at the same time and press the power button to turn on the power.
CURSOR f/
", and press the button "
d
ENTER
" to commit the selection.
68
3.8. Operation Info Mode
3.8.1. Actions
This mode displays the accumulated operating time, power on count and each protection count.
3.8.2. Starting up
Hold down buttons "
Select the "4. OP INFO" using the button "
ZONE SELECT
" and "
CURSOR f/
BACK
" at the same time and press the power button to turn on the power.
", and press the button "
d
ENTER
" to commit the selection.
3.8.3. Operations
Press the "
The following information is displayed in the following order.
(a) Accumulated operating time
FLD
↑ Time display
"
(b) Power on count
FLD
↑ Count display
"
(c) DC / ASO Protection count
Note: No DC / ASO Protection Mode this unit.
FLD
STATUS
L1
L2
L1
L2
L1
L2
" button after starting this device in Operation Info mode.
O pe ra ti onTi me
T ot al :H
STATUS
"
P ow erOnTi me
T ot al :
STATUS
"
P ro te ct io n T im e
D C:/ AS O:
"
(d) Thermal Protection count
Note: No Thermal Protection Mode this unit.
L1
FLD
"
FLD
(e) CURRENT Protection count
Note: No CURRENT Protection Mode this unit.
FLD
"
(Returns to normal display)
P ro te ct io n T im e
L2
T HM A :/B :
L1
P ro te ct io n T im e
L2
T HM E :/F :
L1
P ro te ct io n T im e
L2
C ur re nt :
STATUS
STATUS
STATUS
"
"
"
69
3.9. TUNER STEP mode (U/N only)
3.9.1. Actions
This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed.
3.9.2. Starting up
Hold down buttons "
Select the "5. TUNER FRQ SET" using the button "
ZONE SELECT
" and "
BACK
" at the same time and press the power button to turn on the power.
CURSOR f/
", and press the button "
d
3.9.3. Displays
Start this unit in TUNER STEP mode, select using button "
The following information is displayed in the following order.
(1) AM9kHz/FM50kHz selected
L1
FLD
"
(2) AM10kHz/FM200kHz selected
FLDL2
"
* TU NE RF RQSe t
L2
CURSOR
<AM 9/ FM 50>
" "
0
CURSOR
1
"
<AM 10 /F M2 00>
ENTER
"
CURSOR 0/
" and enter using button "
1
ENTER
" to commit the selection.
ENTER
".
(3) Press the power button to turn off the power.
(4) Press the power button to turn on the power.
70
4. CX870 / CY920 Reboot mode
4.1. Actions
• The CX870 / CY920 is restarted after CX870 / CY920 hangup.
• The CX870 / CY920 can be restarted even in the network standby setting.
("Setup menu" – "Network" – "IP Control" – "Always On")
4.2. Operations
(1) Select "
(2) Hold down buttons "
FL display during CX870 / CY920 reboot
FLDL1
3. Returns to the normal display.
NOTE:
• The CX870 / CY920 Reboot operation is not accepted again for one minute after executing the reboot.
• Reception is prohibited during update, save and load.
Online Music
" as the input source.
M-DAX
" and "
DYNAMIC EQ
" for at least 3 seconds while the power is on.
N et wo rkRe st ar t
5. CX870 / CY920 Initialization mode
5.1. Actions
The following items are initialized.
(1) Favorites
(2) Quick Select
(3) Presets
(4) Internet Radio Recently Played
(5) Flickr contacts
(6) User ID
(7) Resume Playback station
5.2. Operations
(1) Select "
(2) Hold down buttons "
Initializing Display
FLDL1
FLDL1
FLDL1
FLDL1
Complete Display
FLDL1
This is displayed for 5 seconds before returning to the normal display.
Failed Display
FLDL1
Online Music
"
BACK
" and "
ENTER
" for at least 3 seconds while the power is on.
I ni ti al iz in g
I ni ti al iz in g.
I ni ti al iz in g. .
I ni ti al iz in g. ..
C om pl et ed
F ai le d
71
JIG FOR SERVICING
The following jigs (extension cable kit) are used when repairing the PCBs.
Order the jigs from your dealer if necessary.
CAUTION : Incorrect connections may cause malfunction.
• Connection of Jig for DIGITAL PCB
-Items to Be Prepared-
8U- 110084S : EXTENSION UNIT KIT : 1 Set
8U- 110136S : EXTENSION UNIT KIT : 1 Set
Insulation sheet (Not supplied) : 3 sheet
Ground lead (Not supplied) : 3 pc
-Procedures-
(1) Remove the screws.
(2) Remove the connector PCB.
BN23A
BN27A
Front side
BN24ABN25ABN21ABN26A
72
BN27B
BN64C
BN23C
BN21B
BN28B
BN24C BN26C
From HDAM PCB
CN482
(3) Remove the DIGITAL PCB from the chassis and turn it over.
Place an insulation sheet larger than the PCB underneath the DIGITAL PCB.
Connect the earth of the PCB to the chassis using an earth wire, etc.
DIGITALIC404MX25L12845EMI-10GBSOFTWARE:GUI ROM
DIGITALIC2215M570ZF256C5NBSOFTWARE:AUDIO PLD
DIGITALIC421EPM570F256C4NBSOFTWARE:VIDEO PLD
Procedure after Replacement
A : The software has been written. The software is not written at the time of replacement.
B : The software has been written. The software may need to be rewritten by version updates. Check the version.
C : The software has not been written. The software needs to be written after replacement.
See "Firmware Update Procedure" for information on writing the software.
D : The software has been written. Be sure to rewrite with the latest software for your service region.
See "Firmware Update Procedure" for information on writing the software.
IC254/IC264/
IC273/IC283
MX25L1606EM2I-12GBSOFTWARE:DSP1 / 2 / 3 / 4 ROM
dure after
Replace-
ment
Remark
FIRMWARE UPDATE PROCEDURE
1. Updating by USB
The latest rmware can be downloaded to a USB memory for updates.
1.1. Connecting to the USB Memory
(1) Preparation
• USB format : Prepare a USB memory formatted in FAT16 or FAT32.
• Do not run the USB memory through a hub.
• Do not connect a computer to the USB port of this unit using a USB cable.
• Do not use an extension cable when connecting the USB unit.
1.2. Unzip Download File
Unzip the downloaded le on your computer.
AVXXXXXXXUSB_AVXXXXXXX_XXXXXXXXXXXX-XXXX.zip
copy to USB flash drive
You can nd "
rmwares
" folder after unzipped.
Copy that folder to USB ash drive.
You have to put "
rmwares
" folder on root directly on USB ash drive(memory).
75
1.3. File structure on USB Memory
Copy the update les to the USB memory with the following structure:
NOTE:Remove the LAN cable from this unit when performing updates.
Download firmware in
USB flash drive.
76
1.5. Start the update.
Hold down buttons "
HDMI OUT
" and "
STATUS
" at the same time and press the power button to turn on the power.
1.6. Display during USB update
The following message appears on the display after around 30 seconds
Display
L1
FLD
* FI RM WA REUP DA TE
L2
U SBUp da teSt ar t
1.7. Press the "ENTER" key on the remote control unit or this unit.
Then start Firmware Update.
Display
L1
FLD
P le as ew ai t. ..
L2
U pd at eF il eC he ck
1.8. Thermwareupdatenishes.
The following message appears on the display:
Display
FLD
L1
F ir mU pd at e
L2
U pd at eC om pl et e
•
--- Precautions for Updates ---
• Never remove the USB memory before the update is nished.
• Never turn off the power before an update is completed.
• It takes around 1 hour to complete the update.
Once an update is started, normal operations cannot be performed until it is completed.
The GUI menu settings and image adjustment settings of this unit may be initialized.
Take note of your settings beforehand and recongure them after the update.
1.9 Forced USB All Device Write Mode
1.9.1. Actions
Mode used when this unit cannot be recovered.
Forcibly switches this unit to USB update mode.
1.9.2. Operations
Press the "
HDMI OUT
" and "
STATUS
" buttons simultaneously while inserting the AC plug to turn the power on.
1.9.2.Thermwareupdatenishes.
The update after the restart, all devices will be updated.
77
1.10. About the error code
See the table below for error codes and details of faults when the rmware is updated through USB memory.
Error
Code
01
02
03
04
05
08
09
USB Update Error DisplayDetails of Error codeCoping strategies
C o n n e c t i o nf a i l
F i l e s N o t F o u n d
N o t M a t c h F i r m
C o n n e c t i o nf a i l
C o n n e c t i o nf a i l
C o n n e c t i o nf a i l
C o n n e c t i o nf a i l
Unable to detect USB.
0 1
No Firmware File in USB.
0 2
Firmware File in USB for unsupported Model name/area.
0 3
Failed to obtain entire Firmware
information.
0 4
Time Out while obtaining entire
Firmware information.
0 5
Error notication received while
requesting Firmware Info.
0 8
Time Out while obtaining Firmware information.
0 9
Disconnect and connect the USB memory.
Make sure that the Firmware File is in
the USB memory.
Check the supported Model name/area
for the Firmware File.
Start the USB Update again.
Start the USB Update again.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
C o n n e c t i o nf a i l
0A
F i l e s N o t F o u n d
0B
C o n n e c t i o nf a i l
0D
M a i n* * * m i n
10
U p d a t i n gf a i l1 0
M a i n* * * m i n
11
U p d a t i n gf a i l1 1
M a i n* * * m i n
12
U p d a t i n gf a i l1 2
M a i n* * * m i n
13
E r a s ef a i l1 3
Unable to detect USB for Firmware Download.
0 A
No Firmware File for Firmware
Download.
0 B
Received value with invalid Package Version.
0 D
No Update Packet received from
CX870 / CY920 (Time Out).
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
Abnormal data in Update Packet
received from CX870 / CY920
(PacketNoError).
Block Erase failed before rewriting
Main.
Disconnect and connect the USB memory.
Disconnect and connect the USB memory.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
78
Error
Code
14
15
16
USB Update Error DisplayDetails of Error codeCoping strategies
M a i n* * * m i n
U p d a t i n gf a i l1 4
M a i n* * * m i n
U p d a t i n gf a i l1 6
M a i n* * * m i n
U p d a t i n gf a i l1 6
Block Write failed while rewriting
Main.
Error in Verify after rewriting Main
(Check Sum Error).
Setup failure of the transfer method of XModem.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
C o n n e c t i o nf a i l
20
F i l e s N o t F o u n d
21
N o t M a t c h F i r m
22
C o n n e c t i o nf a i l
23
C o n n e c t i o nf a i l
24
C o n n e c t i o nf a i l
25
D o w n l o a df a i l
26
C o n n e c t i o nf a i l
27
M a i n* * * m i n
36
C o n n e c t i o n F a i l 3 6
M a i n* * * m i n
37
F i l e s N o t F o u n d3 7
M a i n* * * m i n
38
N o t M a t c h F i r m3 8
Unable to detect USB after SBL
Mode.
2 0
No Firmware File in USB after SBL
Mode.
2 1
Firmware File in USB after SBL
Mode for unsupported Model
2 2
name/area.
Failed to obtain entire Firmware
information after SBL Mode.
2 3
Time Out while obtaining entire
Firmware information after SBL
2 4
Mode.
Failed to transit to SBL Mode.
2 5
Time Out in Download (writing to
SDRAM) for Firmware Download.
2 6
Failed to write to EEPROM after
SBL Mode.
2 7
Unable to detect USB.
No Firmware File in USB.
Firmware File in USB for unsupported Model name/area.
Disconnect and connect the USB memory.
Disconnect and connect the USB memory.
Check the supported Model name/area
for the Firmware File.
Disconnect and connect the USB memory.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
79
Error
Code
39
3A
3B
3C
3D
3F
50
51
52
54
55
56
57
5A
USB Update Error DisplayDetails of Error codeCoping strategies
M a i n* * * m i n
C o n n e c t i o n F a i l 3 9
M a i n* * * m i n
C o n n e c t i o n F a i l 3 A
M a i n* * * m i n
F i l e s N o t F o u n d3 B
M a i n* * * m i n
U p d a t i n gf a i l3 C
M a i n* * * m i n
U p d a t i n gf a i l3 D
M a i n* * * m i n
C o n n e c t i o n F a i l 3 F
S u b* * * m i n
C o n n e c t i o n F a i l 5 0
S u b* * * m i n
C o n n e c t i o n F a i l 5 1
S u b* * * m i n
N o t M a t c h F i r m5 2
S u b* * * m i n
U p d a t i n gf a i l5 4
S u b* * * m i n
U p d a t i n gf a i l5 5
S u b* * * m i n
C o n n e c t i o n F a i l 5 6
S u b* * * m i n
F i l e s N o t F o u n d5 7
S u b* * * m i n
C o n n e c t i o n F a i l 5 A
Time Out in USB Check.
Unable to detect USB for Firmware Download.
No Firmware File for Firmware
Download.
Error notication received while
requesting Firmware Info.
Time Out while obtaining Firmware information.
Failed to transit to SBL Mode.
Unable to detect USB.
No Firmware File in USB.
Firmware File in USB for unsupported Model name/area.
Error notication received while
requesting Firmware Info.
Time Out while obtaining Firmware information.
Unable to detect USB for Firmware Download.
No Firmware File for Firmware
Download.
Invalid DeviceID in response or no
response from Sub for C command.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
80
Error
Code
5B
5C
5D
5E
5F
60
61
62
63
64
80
81
82
83
USB Update Error DisplayDetails of Error codeCoping strategies
S u b* * * m i n
U p d a t i n gf a i l5 B
S u b* * * m i n
U p d a t i n gf a i l5 C
S u b* * * m i n
U p d a t i n gf a i l5 D
S u b* * * m i n
U p d a t i n gf a i l5 E
S u b* * * m i n
U p d a t i n gf a i l5 F
S u b* * * m i n
U p d a t i n gf a i l6 0
S u b* * * m i n
U p d a t e C h e c k N G6 1
S u b* * * m i n
U p d a t i n gf a i l6 2
S u b* * * m i n
U p d a t i n gf a i l6 3
S u b* * * m i n
U p d a t i n gf a i l6 4
G U I* * * m i n
U p d a t i n gf a i l8 0
G U I* * * m i n
U p d a t i n gf a i l8 1
G U I* * * m i n
U p d a t i n gf a i l8 2
G U I* * * m i n
U p d a t i n gf a i l8 3
NACK received in response or no
response from Sub for L command.
No Update Packet received from
CX870 / CY920 (Time Out).
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
Abnormal data in Update Packet
received from CX870 / CY920
(PacketNoError).
Setup failure of the transfer method of XModem.
NACK received in response or no
response from Sub for P command.
Mismatched Check Sum in response or no response from Sub
for I command.
Failed to start up Sub in Power On
sequence during Update.
Failed to transit to Application
Mode.
Failed to transit to Boot Loader
Mode.
Write Enable Latch Bit not set in
Read after issuing WREN command.
Block Erase failed in Read after
issuing BE command.
No Update Packet received from
CX870 / CY920 (Time Out).
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
81
Error
Code
84
85
86
A2
A3
A4
A6
A7
AE
AF
B1
B2
B3
B4
USB Update Error DisplayDetails of Error codeCoping strategies
G U I* * * m i n
U p d a t i n gf a i l8 4
G U I* * * m i n
U p d a t i n gf a i l8 5
G U I* * * m i n
U p d a t i n gf a i l8 6
E t h e rI M G* * * m i n
C o n n e c t i o n F a i l A 2
E t h e rI M G* * * m i n
F i l e s N o t F o u n dA 3
E t h e rI M G* * * m i n
N o t M a t c h F i r mA 4
E t h e rI M G* * * m i n
U p d a t i n gf a i lA 6
E t h e rI M G* * * m i n
U p d a t i n gf a i lA 7
E t h e rI M G* * * m i n
C o n n e c t i o n F a i l A E
E t h e rI M G* * * m i n
F i l e s N o t F o u n dA F
E t h e rI M G* * * m i n
C o n n e c t i o n F a i l B 1
E t h e rI M G* * * m i n
U p d a t i n gf a i lB 2
E t h e rI M G* * * m i n
U p d a t i n gf a i lB 3
E t h e rI M G* * * m i n
U p d a t i n gf a i lB 4
Abnormal data in Update Packet
received from CX870 / CY920
(PacketNoError).
Abnormal data in Update Packet
received from CX870 / CY920
(DataLength/DataNo).
Mismatched Check Sum in Check
Sum comparison after rewriting.
Unable to detect USB.
No Firmware File in USB.
Firmware File in USB for unsupported Model name/area.
Error notication received while
requesting Firmware Info.
Time Out while obtaining Firmware information.
Unable to detect USB for Firmware Download.
No Firmware File for Firmware
Download.
Time Out in Download (writing to
SDRAM) for Firmware Download.
Error notication received after
rewriting CX870 / CY920 Firm.
Error in Firmware Update (Time
Out).
Failed to transit to BootLoader
Mode.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
82
Error
Code
B5
E t h e rI M G* * * m i n
U p d a t i n gf a i lB 5
USB Update Error DisplayDetails of Error codeCoping strategies
Failed to transit to Application
Mode.
---Check the rmware version after updating.---
After updating the rmware, check the version. See "1. Version Display Mode" (19 page ).
1.11.Devicedisplayduringrmwareupdate
Display of target device during rmware update.
Target deviceUSB Update DisplayError code when an error occurs
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error display, press and hold the "Power operation" button for ve seconds.
After updating the rmware, check the version. See "1. Version Display Mode" (19 page ).
83
2. Updating by DPMS
Download the latest rmware from the internet and update the rmware.
2.1. Network Connection
(1) System Requirements
• A broadband internet connection
• Modem
• Router
• Ethernet cable (CAT-5 or greater recommended)
(2) Settings
Internet
Computer
Modem
ComputerLAN port / Ethernet connector
Router
To WAN port
To LAN port
To LAN port
ETHERNET connector
2.2. Checkandupdatethermware
Check whether new rmware is available. It is also possible to check approximately how long the update will take.
(1) Press the button "
(2) Press the cursor button to select "General" → "Firmware" → "Update" → "Check Update".
(3) Press the button "
• The latest rmware version uploaded to our website is displayed.
• Proceed to (4) if new rmware is available on our website.
• If the latest rmware is already installed, press the button "
(4) Select "Start" using the cursor buttons and then press "
• The power display lights in red and the GUI screen display disappears during the update.
The remaining time of the update is shown on the display of the unit.
• The normal status resumes after the update is completed.
--- Precautions for Updates ---
• The environment and settings must allow connection to broadband Internet for updates.
• Never turn off the power before an update is completed.
• It takes around 1 hour to complete the update.
Once an update is started, normal operations cannot be performed until it is completed.
The GUI menu settings and image adjustment settings of this unit may be initialized.
Take note of your settings beforehand and recongure them after the update.
SETUP
" on the remote control to display the GUI menu.
ENTER
".
ENTER
SETUP
" to exit the menu.
".
84
2.3. About the error code
See the following table for details on the error code, details of the error code, display and coping strategies when updating the rmware from DPMS. (marantz Product Management Server)
Error
Code
01
02
03
04
05
06
07
DPMS Update Error DisplayDetails of Error codeCoping strategies
L o g i nf a i l e d
S e r v e ri sb u s y
C o n n e c t i o nf a i l
C o n n e c t i o nf a i l
C o n n e c t i o nf a i l
C o n n e c t i o nf a i l
C o n n e c t i o nf a i l
Failed to log in to DPMS.
0 1
Line etc. is congested when logging in to DPMS.
0 2
Connection to DPMS failed.
0 3
Failed to obtain entire Firmware
information.
0 4
Time Out while obtaining entire
Firmware information.
0 5
Failed to obtain individual Firmware information.
0 6
Time Out while obtaining individual Firmware information.
0 7
Initialize the unit and try updating
again.
Update in an environment where there
is a small network load.
Update in an environment where there
is a small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
C o n n e c t i o nf a i l
08
C o n n e c t i o nf a i l
09
D o w n l o a df a i l
0A
D o w n l o a df a i l
0B
D o w n l o a df a i l
0C
C o n n e c t i o nf a i l
0D
C o n n e c t i o nf a i l
0E
Error notication received while
requesting Firmware Info.
0 8
Time Out while obtaining Firmware information.
0 9
Error(NG) notication received
while requesting Firmware Down-
0 A
load.
Error(ServerBusy) notication received while requesting Firmware
0 B
Download.
Error(Connect failure) notication
received while requesting Firm-
0 C
ware Download.
Received value with invalid Package Version.
0 D
Connection to DPMS failed.
(Cannot get NTP)
0 E
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
M a i n* * * m i n
10
U p d a t i n g f a i l1 0
M a i n* * * m i n
11
U p d a t i n g f a i l1 1
No Update Packet received from
CX870 / CY920 (Time Out).
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
85
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Error
Code
DPMS Update Error DisplayDetails of Error codeCoping strategies
M a i n* * * m i n
12
U p d a t i n g f a i l1 2
M a i n* * * m i n
13
E r a s ef a i l1 3
M a i n* * * m i n
14
U p d a t i n g f a i l1 4
M a i n* * * m i n
15
U p d a t e C h e c k N G1 5
M a i n* * * m i n
16
U p d a t i n g f a i l1 6
C o n n e c t i o nf a i l
20
C o n n e c t i o nf a i l
21
Abnormal data in Update Packet
received from CX870 (PacketNoError).
Block Erase failed before rewriting
Main.
Block Write failed while rewriting
Main.
Error in Verify after rewriting Main
(Check SumError).
Setup failure of the transfer method of XModem.
SBL Mode after IP Address acquisition failure (AutoIP).
2 0
SBL Mode after IP Address acquisition failure (Time Out).
2 1
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
L o g i nf a i l e d
22
S e r v e ri sb u s y
23
C o n n e c t i o nf a i l
24
C o n n e c t i o nf a i l
25
D o w n l o a df a i l
26
C o n n e c t i o nf a i l
27
M a i n* * * m i n
36
L o g i nf a i l e d3 6
Login incorrect notication SBL
Mode after DPMS connection.
2 2
Server congestion notication SBL
Mode after DPMS connection.
2 3
Connection failure notication
SBL Mode after DPMS connection.
2 4
Failed to transit to SBL Mode.
2 5
Error in Firmware Download (Time
Out).
2 6
Failed to write to EEPROM after
SBL Mode.
2 7
Login incorrect notication DPMS
connection.
Initialize the unit and try updating
again.
Update in an environment where there
is a small network load.
Update in an environment where there
is a small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Initialize the unit and try updating
again.
Check the network connection. Update
in an environment where there is a
small network load.
Initialize the unit and try updating
again.
Update in an environment where there
is a small network load.
M a i n* * * m i n
37
S e r v e ri sb u s y 3 7
M a i n* * * m i n
38
C o n n e c t i o n F a i l 3 8
Server congestion notication by
DPMS connection.
Connection failure notication
DPMS connection.
86
Update in an environment where there
is a small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Error
Code
DPMS Update Error DisplayDetails of Error codeCoping strategies
M a i n* * * m i n
39
C o n n e c t i o n F a i l 3 9
M a i n* * * m i n
3A
D o w n l o a df a i l3 A
M a i n* * * m i n
3B
D o w n l o a df a i l3 B
M a i n* * * m i n
3C
D o w n l o a df a i l3 C
M a i n* * * m i n
3D
C o n n e c t i o n F a i l 3 D
M a i n* * * m i n
3E
C o n n e c t i o n F a i l 3 E
M a i n* * * m i n
3F
C o n n e c t i o n F a i l 3 F
Connect Time Out by DPMS connection.
Error(NG) notication received
while requesting Firmware Download.
Error(ServerBusy) notication received while requesting Firmware
Download.
Error(Connect failure) notication
received while requesting Firmware Download.
SBL Mode after IP Address acquisition failure (AutoIP).
SBL Mode after IP Address acquisition failure (Time Out).
Failed to transit to SBL Mode.
Check the network connection. Update
in an environment where there is a
small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
S u b* * * m i n
50
L o g i nf a i l e d5 0
S u b* * * m i n
51
S e r v e ri sb u s y 5 1
S u b* * * m i n
52
C o n n e c t i o n F a i l 5 2
S u b* * * m i n
54
U p d a t i n gf a i l5 4
S u b* * * m i n
55
U p d a t i n gf a i l5 5
S u b* * * m i n
56
D o w n l o a df a i l5 6
S u b* * * m i n
57
D o w n l o a df a i l5 7
Login incorrect notication DPMS
connection.
Server congestion notication by
DPMS connection.
Connection failure notication
DPMS connection.
Error notication received while
requesting Firmware Info.
Time Out while obtaining Firmware information.
Error(NG) notication received
while requesting Firmware Download.
Error(ServerBusy) notication received while requesting Firmware
Download.
Update in an environment where there
is a small network load.
Update in an environment where there
is a small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
S u b* * * m i n
58
D o w n l o a df a i l5 8
S u b* * * m i n
5A
C o n n e c t i o n F a i l 5 A
Error(Connect failure) notication
received while requesting Firmware Download.
Invalid DeviceID in response or no
response from Sub for C command.
87
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Error
Code
DPMS Update Error DisplayDetails of Error codeCoping strategies
S u b* * * m i n
5B
U p d a t i n gf a i l5 B
S u b* * * m i n
5C
U p d a t i n gf a i l5 C
S u b* * * m i n
5D
U p d a t i n gf a i l5 D
S u b* * * m i n
5E
U p d a t i n gf a i l5 E
S u b* * * m i n
5F
U p d a t i n gf a i l5 F
S u b* * * m i n
60
U p d a t i n gf a i l6 0
S u b* * * m i n
61
U p d a t e C h e c k N G6 1
NACK received in response or no
response from Sub for L command.
No Update Packet received from
CX870 / CY920 (Time Out).
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
Abnormal data in Update Packet
received from CX870 / CY920
(PacketNoError).
Setup failure of the transfer method of XModem.
NACK received in response or no
response from Sub for "P" command.
Mismatched Check Sum in response or no response from Sub
for "I" command.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
S u b* * * m i n
62
U p d a t i n gf a i l6 2
G U I* * * m i n
80
U p d a t i n gf a i l8 0
G U I* * * m i n
81
U p d a t i n gf a i l8 1
G U I* * * m i n
82
U p d a t i n gf a i l8 2
G U I* * * m i n
83
U p d a t i n gf a i l8 3
G U I* * * m i n
84
U p d a t i n gf a i l8 4
G U I* * * m i n
85
U p d a t i n gf a i l8 5
Failed to start up Sub in Power On
sequence during Update.
Write Enable Latch Bit not set in
Read after issuing WREN command.
Block Erase failed in Read after
issuing BE command.
No Update Packet received from
CX870 / CY920 (Time Out).
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
Abnormal data in Update Packet
received from CX870 / CY920
(PacketNoError).
Setup failure of the transfer method of XModem.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
G U I* * * m i n
86
U p d a t i n gf a i l8 6
E t h e rI M G* * * m i n
A0
C o n n e c t i o n F a i l A 0
Mismatched Check Sum in Check
Sum comparison after rewriting.
IP Address acquisition failure
(AutoIP).
88
Turn on the power again. Update will
start automatically.
Check the network connection. Update
in an environment where there is a
small network load.
Error
Code
DPMS Update Error DisplayDetails of Error codeCoping strategies
E t h e rI M G* * * m i n
A1
C o n n e c t i o n F a i l A 1
E t h e rI M G* * * m i n
A2
L o g i nf a i l e dA 2
E t h e rI M G* * * m i n
A3
S e r v e ri sb u s y A 3
E t h e rI M G* * * m i n
A4
C o n n e c t i o n F a i l A 4
E t h e rI M G* * * m i n
A6
U p d a t i n gf a i lA 6
E t h e rI M G* * * m i n
A7
U p d a t i n gf a i lA 7
E t h e rI M G* * * m i n
AE
D o w n l o a df a i lA E
IP Address acquisition failure
(Time Out).
Login incorrect notication DPMS
connection.
Server congestion notication by
DPMS connection.
Connection failure notication
DPMS connection.
Error notication received while
requesting Firmware Info.
Time Out while obtaining Firmware information.
Error(NG) notication received
while requesting Firmware Download.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Check the network connection. Update
in an environment where there is a
small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
E t h e rI M G* * * m i n
AF
D o w n l o a df a i lA F
E t h e rI M G* * * m i n
B0
D o w n l o a df a i lB 0
E t h e rI M G* * * m i n
B1
D o w n l o a df a i lB 1
E t h e rI M G* * * m i n
B2
U p d a t i n gf a i lB 2
E t h e rI M G* * * m i n
B3
U p d a t i n gf a i lB 3
E t h e rI M G* * * m i n
B4
U p d a t i n gf a i lB 4
E t h e rI M G* * * m i n
B5
U p d a t i n gf a i lB 5
Error(ServerBusy) notication received while requesting Firmware
Download.
Error(Connect failure) notication
received while requesting Firmware Download.
Error in Firmware Download (Time
Out).
Error notication received after
rewriting CX870 / CY920 Firm.
Error in Firmware Update (Time
Out).
Failed to transit to Boot Loader
Mode.
Failed to transit to Application
Mode.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Turn on the power again. Update will
start automatically.
Update in an environment where there
is a small network load.
Initialize the unit and try updating
again.
Initialize the unit and try updating
again.
89
Device display during rmware update
Display of target device during rmware update.
Target deviceDPMS Update DisplayError code when an error occurs
L1
Main CPU
M a i n* * * m i n
L2
U p d a t i n g* * %
10 - 16
36 - 3F
Sub
Audio PLD
VIDEO PLD
DSP
GUI Serial Flash
CX870 / CY920 second
er
Boot Load-
L1
S u b* * * m i n
L2
U p d a t i n g* * %
L1
A P L D* * * m i n
L2
U p d a t i n g* * %
L1
V P L D* * * m i n
L2
U p d a t i n g* * %
L1
D S P 1* * * m i n
L2
U p d a t i n g* * %
L1
D S P 2* * * m i n
L1
D S P 3* * * m i n
L1
D S P 4* * * m i n
L1
G U I* * * m i n
L2
U p d a t i n g* * %
L1
E t h e rS B L* * * m i n
L2
U p d a t i n g* * %
50 - 52
54 - 58
5A - 62
50 - 52
54 - 58
5A - 62
50 - 52
54 - 58
5A - 62
50 - 52
54 - 58
5A - 62
50 - 52
54 - 58
5A
62
80 - 86
A0 - A4
A6 - A7
AE - B5
L1
CX870 / CY920
CX870 / CY920
cy Mode)
Image
Image (Emergen-
E t h e rI M G* * * m i n
L2
U p d a t i n g* * %
L1
P l e a s ew a i t . . .
L2
U p d a t er e t r y
Checking the Firmware Version After an Update
After updating the rmware, check the version.
See "1. Version Display Mode" (19 page ).
A0 - A4
A6 - A7
AE - B5
–
90
SURROUND MODES AND PARAMETERS
Sound modes and channel output
DDDDDDDDD
SDDDDDDDDDDDDD
ContentsConnectionsPlaybackSettingsTipsAppendix
z1
The applicable sound mode includes “Dolby Surround” and sound modes that have “+Dolby Surround” in the sound mode name.
7 Audio is output when “Subwoofer Mode” in the menu is set to “LFE+Main”. (v p. 231)
ContentsConnectionsPlaybackSettingsTipsAppendix
Sound modes and surround parameters
Surround Parameter
Virtual
ContentsConnectionsPlaybackSettingsTipsAppendix
S This indicates the audio output channels or surround parameters that can be set.
D This indicates the audio output channels. The output channels depend on the settings of “Speaker Config.” (v
.
Sound mode
Direct/Pure Direct (2-channel)
Direct/Pure Direct (Multi-channel)
DSD Direct (2-channel)
DSD Direct (Multi-channel)
Stereo
Multi Ch In
Dolby Surround
DTS Neo:X
Audyssey DSX
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
Dolby Atmos
DTS Surround
DTS 96/24
DTS-HD
DTS Express
Multi Ch Stereo
Virtual
z2
z3
z4 Audio is not output when “Speaker Config.” - “Surr. Back” in the menu is set to “1 spkr”. (v
z5 Audio is output from the speakers specified in the “Surround Parameter” – “Speaker Select” settings. (v
z6
z
z
1
z
2
®
The applicable sound mode includes “DTS Neo:X” and sound modes that have “+Neo:X” in the sound mode name.
A signal for each channel contained in an input signal is output as audio.
Audio is output from the speakers specified in the “Audyssey DSX®” settings. (v
Front L/R Center Surround
S
SDD
S
SDDD
SD
SDD
SDD
SDDDDDD
SDD
SDDD
SDD
SDD
SDDDD
SDDDD
SDD
SDDDD
SDDDDDDDDDD
SD
Surround
L/R
Front wide
back L/R
L/R
z
D
3Dz3Dz3
z
3
D
z
D
4
z
z
5
z
D
z
3Dz3Dz3
D
z
3Dz3Dz3
D
z
3Dz3Dz3
D
z
z
5
height L/R
5
6Dz6
5
p. 183)
Front
z
5
z
5
Channel output
Top Front
L/R
z
5
p. 225)
Top
Middle L/R
z
5
p. 177)
p. 224).
Top Rear
Rear
Front
L/R
Height L/R
z
z
5
5
Dolby
Enabled
L/R
Surround
Enabled
Dolby
L/R
Back
Dolby
Enabled
L/R
Subwoofer
z
7
D
D
z
7
D
D
D
D
D
D
.
Sound mode
Direct/Pure Direct (2-channel)
z
Direct/Pure Direct (Multi-channel)
4
z
4
Dialog
Level
Adjust
DSD Direct (2-channel)
DSD Direct (Multi-channel)
z
4
S
Stereo
Multi Ch In
Dolby Surround
DTS Neo:X
Audyssey DSX
®
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
Dolby Atmos
DTS Surround
DTS 96/24
DTS-HD
DTS Express
Multi Ch Stereo
S
S
S
S
S
S
S
S
S
S
S
S
S
S
z
1 - z5 : “Sound modes and surround parameters” (v p. 300)
Subwoofer
Level
Adjust
S
Cinema EQLoudness
z
5
Management
z
1
S
SSS
z
5
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
Dynamic
Compression
z
2
S
SS
S
S
SSS
S
S
S
S
S
S
S
S
Low
Frequency
Effects
Speaker
z
Select
3
S
S
S
S
S
S
S
S
S
S
S
SS
S
Center Gain
91
.
Sound mode
Virtual
SS
SS
ContentsConnectionsPlaybackSettingsTipsAppendix
z9
This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz.
ContentsConnectionsPlaybackSettingsTipsAppendix
Types of input signals, and corresponding sound modes
2-channel signalMulti-channel signal
Dolby Surround
1 - z8: “Types of input signals, and corresponding sound modes” (v p. 303)
ContentsConnectionsPlaybackSettingsTipsAppendix
Direct/Pure Direct (2-channel)
z
Direct/Pure Direct (Multi-channel)
Tone
z
6
®TM
MultEQ XT32Dynamic EQ
z
7
z
4
z
4
8
Surround Parameter
Dynamic Volume Audyssey LFC
z
8
DSD Direct (2-channel)
DSD Direct (Multi-channel)
Stereo
Multi Ch In
Dolby Surround
DTS Neo:X
Audyssey DSX
®
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
Dolby Atmos
DTS Surround
DTS 96/24
DTS-HD
DTS Express
Multi Ch Stereo
This item can be selected when the Dolby Digital, Dolby Digital Plus, Dolby TrueHD or Dolby Atmos signal is played back.
z1
This item can be selected when the Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos or DTS is played back.
z2
This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.
z3
During playback in Pure Direct mode, the surround parameters are the same as in Direct mode.
z4
z5 This setting is available when “Subwoofer Mode” in the menu is set to “LFE+Main”. (v
z6 This item cannot be set when “Dynamic EQ” is set to “On”. (v
z7
This item cannot be set when Audyssey
z8
This item cannot be set when “MultEQ
z
4
SS SSSS
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S SS
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
p. 231)
®
Setup (Speaker Calibration) has not been performed.
®
XT32” in the menu is set to “Off”. (v p. 180)
p. 181)
M-DAX
z
8
Audyssey DSX
®
SS
S
S
S
S
S
S
S
S
S
SS
S
S
S
S
S
S
S
S
z
9
S
S
F This indicates the default sound mode.
S This indicates the selectable sound mode.
.
Dolby
DTS
DSD
PCM
DTS-HD
DTS
DTS ES
DTS ES
Analog /
NOTE
z
1
z
1
PCM
Digital
(+/HD)
(-HD)
(Super
Audio
CD)
Multi
Express
Dscrt6.1
z
3
F
z
4
F
F
SSF
DTS Surround
DTS-HD MSTR
DTS-HD HI RES
DTS ES Dscrt6.1
DTS ES Mtrx6.1
DTS Surround
Sound mode
DTS 96/24
DTS(-HD) + Dolby Surround
DTS Express
DTS(-HD) + Neo:X
DTS Neo:X
Dolby Surround
Dolby Atmos
Dolby TrueHD
Dolby Digital+
Dolby(D+)(HD) + Dolby Surround
Dolby Digital
Dolby(D)(D+)(HD) + Neo:X
z
2
SSFS
z
2Sz8
SSSSS
F
SSSSS
SFSS
z
Mtrx6.1
F
DTSDolby
Atmos
z
5
F
F
S
Sz7
z
6
Dolby
Dolby
Digital
Plus
Dolby
Digital
(EX)
TrueHD
S
S
FFF
S
SSS
DSD
(Super
Audio
CD)
92
.
Sound mode
2-channel signalMulti-channel signal
SSSS
SSSSSSSSSSSSSSS
SSSS
SSSS
SSSS
SSSS
SSSS
SSSS
Stereo
FSSFSSSSSSSSSSS
ContentsConnectionsPlaybackSettingsTipsAppendix
1
This item can be selected when surround back speakers are used.
z10
This item can be selected when the input signals contain surround back signals.
ContentsConnectionsPlaybackSettingsTipsAppendix
Multi Ch In
Multi Ch In
Multi Ch In + Dolby Surround
Multi Ch In + Neo:X
Multi Ch In 7.1
Audyssey
Audyssey DSX
Direct
Direct
DSD Direct
Pure Direct
Pure Direct
DSD Pure Direct
Original sound mode
Multi Ch Stereo
Rock Arena
Jazz Club
Mono Movie
Video Game
Matrix
Virtual
Stereo
NOTE
z
2
z
1Fz10
®
Dolby
PCM
Digital
(+/HD)
z
SSSSSSSSSSSS
9
S
SSSSSSSSSSSSS
SSSSSSSSSS
SSSSSSSSSS
SSSSSSSSSS
SSSSSSSSSS
SSSSSSSSSS
SSSSSSSSSS
DSD
DTS
(-HD)
PCM
(Super
Audio
CD)
SS
SS
DTS-HD
Multi
FF
SS
SS
SSSSSS
DTS
Express
DTS ES
Dscrt6.1
DTS ES
Mtrx6.1
DTSDolby
Atmos
Sz8
S
S
S
S
S
S
Dolby
TrueHD
z
8
z
8
z
8
z
8
z
8
z
8
Dolby
Digital
Plus
Analog /
z
The “Cinema” mode, “Music” mode or “Game” mode can be selected. This item can be selected when using any of the surround back, front height or front wide speaker.
z2
This item can be selected when the input signal is DTS-HD Master Audio.
z3
This item can be selected when the input signal is DTS-HD Hi Resolution.
z4
This item can be selected when the input signal is DTS 96/24.
z5
This can be selected when the Dolby Atmos signal contains the Dolby TrueHD signal.
z6
This can be selected when the Dolby Atmos signal contains the Dolby Digital Plus signal.
z7
This can be selected when the Dolby Atmos signal contains the Dolby TrueHD or Dolby Digital Plus signal.
z8
The default sound mode for the AirPlay playback is “Direct”.
z9
Dolby
Digital
(EX)
DSD
(Super
Audio
CD)
93
TROUBLE SHOOTING
1. POWER
1.1. The unit does not power on
The unit does not power on
Does the power indicator
on the front panel ash in
green or white when the
power is turned on?
YES
Does the power display
on the front panel change
to lighting in green after
approximately 10 seconds?
NO
Does the power indicator on
NO
the front panel ash in red
when the power is turned on?
Has a fuse broken?
Is DC5V being supplied
from the SMPS PCB (BN903)
to the DIGITAL PCB?
Check the circuits around
the Microprocessor on the
DIGITAL PCB and replace
any faulty parts.
YES
Has a fuse broken?
NO
NO
YES
YES
YES
YES
See "1.2.Fuse is blown."
Is DC5V output even when
NONO
the connector (CN903)
supplying power from the
SMPS PCB to the DIGITAL
PCB is removed?
YES
Check for breakages and short
circuits in the circuits and parts
between CN903 on the DIGITAL
PCB and the microprocessor power
supply and replace any faulty parts.
Are any parts not fully connected in the connectors that
NONO
connect the PCBs?
YES
TO "6.SMPS"
(See 107 page)
TO "3.6.Protection History Display Mode"
(See 68 page)
Has a fuse broken?
NO
Check the voltage of pins
1-7 of CN704 on the DIGITAL
PCB while the power display
is ashing in green or white.
0.6V or -0.6V
Remove the connector (CN971) of the SPK PCB.
Check the "3.6. Protection history display mode"
(See 68 page)
YES
See "1.2.Fuse is blown."
Check the circuits around the Micropro-
0V
cessor on the DIGITAL PCB and replace
any faulty parts.
1.2. Fuse is blown
Broken fuse
Check for leaks and short
circuits in the parts on the
primary side. Replace any
faulty parts.
Check the rectier diode in
the rectier circuit on the
secondary side, and check
the circuit for short circuits.
Replace any faulty parts.
Connect the connectors correctly.
Check for short circuits between
the regulator output terminal and
GND in the power supply stabilization circuit. Replace faulty parts
if there is a short circuit.
Replace the fuse after repair.
94
2. Analog video
Perform the operation below beforehand.-
Check it whether connection cable and Monitor are normal.
b
VIDEO Convert is set to ON.
b
Setting as follows.
b
V : SAT
COMPONENT : SAT
MONITOR OUT (CVBS/Cmponent/HDMI) output NG
Input
CVBS
To A
A
CVBS,COMPONENT
Is the power supply voltage being output correctly?
V+5V : CN28B-6pin
V-5V : CN28B-8pin
(SIDE CNT PCB)
Check of the I2C control signal for video selector IC
(IC511).
I2C(SCL) : BN21A-6pin(AVSCL)
I2C(SDA) : BN21A-4pin(AVSDA)
See the sample wave form 96 page
(DIGITAL PCB)
Input
NO
YES
NO
Input
COMPONENT
· Defective connection of SIDE CNT PCB(BN77B).
· REGULATOR(SPEAKER) PCB aw.
The DIGITAL PCB is faulty.
YES
Check the input signal to video decoder IC (IC351).
V : R3527
COMPONENT-Y : R3530
COMPONENT-Cb : R3528
COMPONENT-Cr : R3529
(DIGITAL PCB)
YES
· CVBS Monitor Out
COMPONENT Monitor Out ⇒ TO B
· HDMI Out ⇒ To Troubleshooting "HDMI/DVI"
NO
· Defective connection of FRONT CNT PCB
(CN21A)
The parts between VIDEO PCB aw. ⇒ TO B
95
B
The VIDEO PCB is faulty.
Use the jigs to extend the DIGITAL PCB.
YES
Check power supply voltage and I2C control signal of
video selector IC.(IC511)
V+3.3V : J5043
V-5V : J5042
I2C(SCL) : J5046
I2C(SDA) : J5047
(VIDEO PCB)
YES
Check the signal input to video selector IC. (IC511)
V : C5107
OMPONENT-Y : J5010
COMPONENT-Cb : J5007
COMPONENT-Cr : J5006
(VIDEO PCB)
YES
Check the signal output from video selector IC. (IC511)
(VIDEO PCB) to MONITOR to DIGITAL PCB
V : J5019 BN21B-17pin
OMPONENT-Y : J5021 BN21B-15pin
COMPONENT-Cb : J5028 BN21B-13pin
COMPONENT-Cr : J5029 BN21B-11pin
YES
NO
Power supply IC (IC513) aw.
SIDE CNT PCB(BN28B) aw.
Video selector IC(IC511) の aw.
NO
The circuit between IC511 are faulty.
NO
Defective the soldering video selector IC (IC511) or
video selector IC (IC511) aw.
MONITOR OUT
Output terminal (JK511 or JK513) or pattern aw.
HDMI OUT
Defective connection of FRONT CNT PCB (BN21B) or
FRONT CNT PCB pattern aw.