ACCESSORIES
!!I
Accessories
Filters
There are five different types of
filters (Y2, YG, 02, UV, and SL) for
each filter srze described in the
system chart on page 41.
l There are two different diame-
ters for the 80mm f/2.8 and
105mm f/3.5 lenses. When you
order filters for these lenses,
always specify the diameter of
your lens.
l When using a 49mm diameter
filter, employ the 49mm filter
for Mamrya C; otherwise attach-
ing the lens hood might be impossible. When you order filters,
always specify the MAMIYA C
Professional type.
l To attach a filter to a lens of
49mm filter diameter, place your
palm on the protective lens ring
screwed into the front barrel of
the lens, turn the ring counter-
clockwise to remove it, and then
screw in the filter. When a filter
is not used, always replace the
ring to protect the lens barrel.
Lens hoods
There are five different types of
lens hoods available for interchangeable lenses.
Lens hood for 55mm lens
Lens hood for 65mm lens
Lens hood 42mm 4 for 80mm
f/2.8 (chrome type) and 105mm
f/3.5 (chrome type) lenses
Lens hood 48mm
f/2.8 (black type) 105mm f/3.5
D and 135mm f/4.5 lenses
Lens hood for super 180mm,
180mm and 250mm lenses
Lens hoods marked with an
(*)
asterisk
which can be inclined. Attach
the lens hood to the lens with
this plate upward. When light
reflected from the lens hood to
the viewing lens becomes annoy-
ing while focusing, due to a
certain light condition, incline
the side plate to eliminate the
annoying reflection.
All of these lens hoods are com-
paratively new type attached
only to the taking lens. Old type
lens hoods are also acceptable.
have a side plate
(*)
(*)
6
for 80mm
(*)
Lens cases
Seven types of hard leather cases
are available for protecting the following interchangeable lenses :
55mm, 65mm, 80mm, 105mm,
135mm, 180mm, and 250mm.
Soft leather case
The soft leather case is widely
applicable to protect interchange-
able lenses for the Mamrya C
Professional or to store accessories.
This case also can hold lenses
for the Mamiya Press and Mamiya
RB.
24
H
Accessories
Single Exposure Attachment
By using the single exposure attachment provided, single
exposures can be made of dry plates (2
6.5x9cm) or cut films (4 3/4 x 6 1/2 in. cut film divided
into four 1/4
3/4 x 6 1/2 in. cut film divided into four one-quarter sizes,
use a J-type film sheath. When using 2 1/2 x 3 1/2 in.
film, use a D-type film sheath.
Installing Method
Replace the camera back cover with the exclusive back
cover for single exposure. Always remove the spool in the
camera. Install a holder containing a dry plate or cut film
on the exclusive back cover, closing the outer frame of the
back cover to complete preparation.
PRECAUTION
Since the position of its focusing surface differs, the
conventional single exposure attachment for the MAMlYA
series cannot be utilized on this camera.
sizes
or 2 1/2 x 3 1/2 in.) When using 4
1/2 x 3
1/2 in.,
C
25
Focusing Screen
The following types
of focusing screen are
available, replaceable
according to the photographing purpose
A metal frame is provided for all focusing
screens.
.
Matted entire surface ; Fresnel lens
(except center circular portion);
with exposure factor scale.
Matted entire surface (except cen-
ter circular portion); with exposure factor scale.
For general photography
Suitable for any lens
Focusing precision by the split
prism is sensitive compared with
the No. 2 Rangefinder Spot
4’
R
Accessories
Grip holder (for
The gr,o holder is a very
“enlent
accessory for hand-
holding the camera While taking pictures or for carrying the
camera. Its accessory shoe is
attached on the top of the grip.
Mamiya
con-
Pistol grip
This grip, which supports
the camera from the bottom,
has a trigger type shutter
release button which many
persons prefer when following
sports action.
C)
Grip holder (for Mamiya
Magnifying Hood
This magnifying hood may
be used instead of the focusing
hood. By turning the knob
on the side of this hood, either
3. 5X or 6X magnification can
be selected.
C330 &
RB)
27
Porrofinder
By attaching this Porrofinder
instead of the regular focusing
hood, the camera can be held
at eye level. The image in the
finder is right side up and correct right to left ... actual visual
focusing.
Magnification of this finder
approximately doubles the image
on the ground glass focusing
screen.
CdS Porrofinder
This is a Porrofinder with
built-in
Match the index needles
within the finder by turning
the dial on the back of the
finder, and read the dial
scale. This device measures
the amount of light traveling
through the viewing lens
offering corrrect exposure
setting even
CdS
exposure meter
for
amateurs.
Prism Finder
Through this prism finder, the
image on the ground glass focus-
ing screen appears exactly as the
subject is seen. Really an indispensable accessory for eye level
photo-journal photos or candid
shots.
Magnification of this finder is
approximately 2.5 times the
image on the ground glass focusing screen, particularly bright
and clear.
Eye Correction Lens
This lens, designed to correct visibility is installed
inside the eyepiece ring of the Porrofinder,
rofinder or Prism Finder.
Nine types of lenses are provided from +2.5 to -2
diopter (each diopter is +2.5, +2.0, +1.5, +1.0,
+
0.5,
-0.5,
-1.0, -1.5 and -2.0).
When installing the lens on the finder, hold the
milled portion of the eyepiece
and finger and turn it counterclockwise to remove the
ring. When the lens is a
it with the flat surface outside and when it is a minus
(concave) lens place the concave surface on the ex-
terior then screw the ring into its original position.
ring
with the thumb
plus
(convex) lens,
CdS
Position
Por-
28
Accessories
Tripod Adapter Type P Flashgun Adapter
The flashgun adapter, designed for the Mamiya flashgun, is
provided with an accessory shoe
for accommodating other brands
of clip-on type flash units.
Flashgun
Highly efficient large BC type
flashgun-usable with both a
screw-base bulb and a bayonet
type base bulb-- supplies suf-
ficient light for taking picutures
under any condition.
30
Accessories
Loading...