Mackie ART200A Parts list
Art Series
Two-Way Active Speaker System
ART200A
SPEAKER
■ Careful acoustic design and advanced materials
have resulted in an exceptional full range, full fidelity,
self-contained sound system. The ART200A provides
an ideal combination of high power, low distortion and
wide bandwidth for permanent installations.
■ The two-way design consists of a 12" woofer that
uses a massive magnet structure for accurate bass
reproduction and a CD horn loaded to a 1" exit compression driver. The CD horn is a part of the molded
enclosure. Two discrete power amplifiers and an electronic crossover are matched to the two transducers
and provide time correction, CD horn compensation
and peak-limiting, as well as over-excursion and
thermal protection.
■ The ART200A will accept a balanced or unbalanced
(switch selected) microphone or line input, adjusted by
a single rotary control.
■ All components are housed in a lightweight, vented
enclosure formed from polypropylene that is extremely
rigid. The woofer is protected by a metal grille. All controls and connectors are recessed on the rear. A 1-3/8"
stand socket and M10 threaded inserts are molded
into the cabinet to provide quick and easy installation
using specially designed accessory mounting hardware.
■ This Mackie Industrial product is covered by an
exclusive, one-time, NO FAULT repair policy in addition
to a five year limited warranty.
Features
■ 90° x 70° constant-directivity horn with 1"
exit compression driver
■ 12" high-efficiency woofer
■ Internal bi-amplifier: 120W LF, 40W HF, and
driver-optimized electronic crossover
■ Switchable balanced mic/line input
■ Total system protection: over-excursion, thermal,
short circuit and peak limiting
■ Compact, lightweight polypropylene enclosure
■ Built-in hand grip, M10 fly points and stand socket
■ Optional installation accessories available
■ Exclusive Mackie Industrial — one-time, NO FAULT
repair policy
■ Five year limited warranty
oF 6 PAGES
1
OF 6 PAGES
ART200A
APPLICATIONS
■ Live Sound/Music Reinforcement
■ High-Level AV Playback
■ Large Speech Systems
■ Active Floor Monitors
Two-Way Active Speaker System
ART200A
SPEAKER
ART200A
oF 6 PAGES
2
OF 6 PAGES
Specifications
System Acoustic
Frequency Range (–10 dB): 50Hz–19kHz
Frequency Response (–3 dB): 70Hz–17kHz
Horz. Coverage Angle (–6 dB): 90°, averaged
1kHz to 10kHz
Vert. Coverage Angle (–6 dB): 70°, averaged
1kHz to 10kHz
Directivity Factor; Q(DI): 9.5 (9.8), averaged
1kHz to 10kHz
System Sensitivity1: 101dB 1W @ 1m
Rated Maximum Peak2: 122dB @ 1m
Crossover: 1.8kHz, 24dB/octave,
0.3mS HF delay
Speaker Protection: Thermal, over-excursion
Transducers
Low-Frequency: 12" (300mm) woofer
High-Frequency: Polynomial horn-loaded
1" (25mm) compression driver
Electronics
Power Amplifier Rating: LF: 120W, HF: 40W
Distortion: 0.1% THD, nominal power @
1kHz and 10kHz
Inputs: Mic: 8mV, 1.3kΩ balanced,
650Ω unbalanced, XLR
Line: 125mV, 19kΩ balanced, 10kΩ unbalanced
Output: XLR connector, parallel to input
Indicators: Power On, Limiter active
Controls, Switch: Mic/Line, Music/Voice EQ,
Power On/Off, Voltage
Selector Music EQ: Off/+4dB @ 65Hz,
+4dB @ 12kHz
Voice EQ: Off/+4dB @ 3kHz,
+4dB @ 6kHz
Controls, Rotary: Input Volume
Electronics Protection: Thermal, limiting, short circuit
Power Requirements: 115/230 VAC, 2A, 50/60Hz
Physical
Enclosure: Gray, semi-trapezoidal,
reinforced polypropylene
Dimensions (HxWxD): 24.42" x 15.36" x 12.29"
(620mm x 390mm x 312mm)
Weight: 39.7lbs. (18kg)
Mounting: Four M10 metal threaded inserts,
1.375" (35mm) lockable stand mount
1
Measured on axis in the far field, referenced back to 1 watt RMSfrom maximum power and to 1 meter
distance using the inverse square law. Listed sound pressure represents an average from 300Hz to 3kHz.
2
RMS using 20Hz to 20kHz, PN Spectrum, Peak for 2 hours with +6 dB crestfactor.
Options
ART A-2 Wall mount bracket, black
ART A-5 Swivel, tilt, wall mount
hardware, black
ART A-7 Full front metal grille, black
ART A-11 U-bracket, black
Loading...