Mackie ART200A User Manual

Specifications

System:

Freq. Range (–10 dB):

50Hz-19kHz

Freq. Response (±3 dB):

70Hz-17kHz

Horz. Coverage Angle (–6 dB):

90°, averaged 1kHz-10kHz

Vert. Coverage Angle (–6 dB):

70°, averaged 1kHz-10kHz

Directivity Factor Q (DI):

9.5 (9.8), averaged 1kHz-10kHz

System Sensitivity:

101 dB, 1W@1m

Rated Maximum SPL:

122 dB @ 1 m (3.3 ft) peak

HF Protection:

Dynamic

Transducers:

Low Frequency:

12" (300 mm) diameter woofer

High Frequency:

1" (25 mm) compression driver,
horn loaded

Preamp and Processor:

Input Sensitivity:

Mic In: 8mV
Line In: 125mV

Input Impedance:

Mic In: 650Ω unbalanced

1.3kΩ balanced

Line In: 10kΩ unbalanced

19kΩ balanced

Crossover Frequency and Slope:

1.8kHz; 24 dB/octave

Time Alignment:

Analog, 0.3 ms HF delay

Speaker Protection:

Thermal, over-excursion

Music Equalization:

+4.3 dB @ 65Hz
+4.0 dB @ 12kHz

Voice Equalization:

+4.0 dB @ 3kHz
+4.0 dB @ 6kHz

Indicators:

Power ON, Limiter

Amplifiers:

LF Amplifier Power:

120 watts RMS

HF Amplifier Power:

40 watts RMS

Distortion:

< 0.1% THD at rated power

Amp Protection:

Thermal, limiter, short circuit

Power Supply:

115/230 VAC, 2A, 50/60 Hz

Physical:

Enclosure:

Asymmetrical trapezoidal,
reinforced polypropylene

Mounting:

Lockable 1-3/8" (35mm) stand
mount

Rigging Inserts:

4 points, accepts M10 threaded
hardware

Input/Output Connectors:

2 XLR balanced

Dimensions HxWxD:

24.4" x 15.4" x 12.3"
(620 mm x 390 mm x 312 mm)

Net Weight:

39.7 lb (18.0 kg)

[e-mail]

16220 Wood-Red Road NE Woodinville, WA 98072

TEL [phone], FAX [phone]

UK +44.1268.570.808, FAX [phone] [e-mail]

ITALY +39.0522.354.111, FAX [phone] [e-mail]

FRANCE +33.3.8546.9160, FAX [phone] [e-mail]

GERMANY +49.2572.96042.0, FAX [phone] [e-mail]

Part No. 910-161-20 Rev. A 2/00
© 2000 Mackie Industrial. All Rights Reserved. Printed in the USA.

The ART200A is a full-range two-way
professional active speaker system that
combines high power and wide bandwidth in
a light-weight enclosure for fixed-installation
systems. The 12" low-frequency transducer, in
combination with a 1" compression driver
coupled to an integral 90˚ x 70˚ constant
directivity polynomial horn, form an extremely
powerful package for any small to medium­sized sound reinforcement application.

It features a balanced XLR input with a
Mic/Line switch and a paralleled balanced
XLR output for cascading multiple speakers.
Rear panel controls also include Music and
Voice equalization switches, a rotary volume
control, and an input limiter.

The two built-in power amplifiers provide
120W for the LF driver and 40W for the HF
driver. The enclosure is constructed of high­strength polypropylene, with M10 threaded
inserts on all four sides for rigging, and an
integral locking 1-3/8" socket in the bottom
for mounting on a standard speaker stand.

Safety First!

Before connecting and using the
equipment, please read this Quick-Start Guide
carefully and keep it for future reference.

WARNING! This equipment has been
designed to be installed by qualified
professionals only! There are many factors to
be considered when installing professional
sound reinforcement systems, including
mechanical and electrical considerations, as
well as acoustic coverage and performance.
Mackie Industrial strongly recommends that
this equipment be installed only by a
professional sound installer or contractor.

CAUTION: To avoid the risk of electric

shock, never allow this equipment to

be exposed to rain or dampness.

ART200A

Active Speaker System

Quick-Start Guide

1. Never install, connect, or disconnect
the unit with the power supply on.

2. Before powering up the speaker,
make sure the voltage select switch
corresponds to the AC Voltage supply.

3. Make sure the safety ground on the
power cord is properly grounded.

4. To prevent the risk of electric shock,
never open the unit. There are no
user serviceable parts inside.

5. To ensure normal cooling of the
amplifier, make sure the unit is well­ventilated. Avoid exposure to direct
sunlight or proximity to any heat
source, dust, or dampness.

ART 200A

ACTIVE SPEAKER SYSTEM

INPUT

OUTPUT

LINE/MIC

VOLUME

MUSIC

VOICE

ON LIMITER

WARNING:

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

REPLACE WITH THE SAME TYPE FUSE AND RATING.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE

SERIAL NUMBER

CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE INDUSTRIAL • MADE IN ITALY

PATENTS PENDING • COPYRIGHT ©1999 THE FOLLOWING ARE TRADEMARKS /REGISTERED TRADEMARKS

OF MACKIE DESIGN INC.: "MACKIE", "MACKIE INDUSTRIAL", & THE "RUNNING MAN" FIGURE

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

AVIS:

RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.

DEBRANCHER AVANT DE REMPLACER LE FUSIBLE

MANUFACTURING DATE

THIS APPARATUS

MUST BE GROUNDED

LINE
MIC

OFF
ON

OFF
ON

Rear Panel Features
and Controls

1. INPUT is a balanced XLR input jack that
accepts mic-level or line-level signals.

2. OUTPUT is a balanced XLR output jack in
parallel with the INPUT jack, allowing the
signal to “loop through” for daisy-chaining
speakers together.

3. LINE/MIC switch for mic-level or line-level
signals at the INPUT.

4. VOLUME control adjusts the input-stage
gain.

5. MUSIC equalization switch ON provides a
low-frequency and high-frequency boost.

6. VOICE equalization switch ON provides a
gentle boost at 3kHz and 6kHz.

7. ON indicator illuminates when the POWER
switch is turned on.

8. LIMITER indicator illuminates when the
limiting protection circuits are activated.

9. POWER switch turns the AC power on and
off.

10. Voltage Select Switch for setting the AC
voltage operation for the voltage being
used.

11. IEC AC Socket. Connect the detachable
power cord to the socket. The protection
fuse is also contained in the AC socket.

CAUTION: Replace fuse only with the same
type as indicated on the rear panel.

12. Grounding Terminal provides an additional
safety grounding point.

Connections

The XLR connectors use the following AES
standard:
Pin 1 = Ground (Shield)
Pin 2 = Hot (+)
Pin 3 = Cold (–)

Installation

A 1-3/8" (35mm) socket is provided in the
bottom of the cabinet for mounting the
loudspeaker on a speaker stand.

The ART200A can be suspended with
approved rigging hardware. Always use at

least two M10 threaded inserts located
on opposite sides of the enclosure. The

speaker must be positioned so that the
weight of the enclosure is equally distributed
over the two inserts.

WARNING: Never attempt to suspend the
ART Series loudspeakers by their handles.
Consult a professional rigger or structural
engineer prior to suspending loudspeakers
from a structure not intended for that use.
Always know the working load limit of the
structure supporting the loudspeaker array.
Always make sure that the rigging hardware
minimum rating is at least five times the
actual load.