READ ME FIRST
QUICK INSTALL GUIDE
Dual-Band Wireless 600N Router
XWR-600
Includes:
One: XWR-600 Dual-Band Wireless 600N Router
Two: Attached Dual Band Antennas
One: Ethernet Cable
One: Power Adaptor
ROUTER SETUP AND CONFIGURATION
Physical Installation
1
The XWR-600 Wireless Router is designed for simple and efficient installation
on a desk or other horizontal surface. Be sure to place the XWR-600 where
there is adequate room around the device for ventilation.
Connecting Ethernet and Power
2
WAN Connection: Connect the Ethernet cable from the modem/router
equipment provided by your Internet Service Provider (ISP) to the black
WAN port of the XWR-600.
AC Power: Connect the included AC Adapter to the XWR-600 first and then
to the AC outlet.
Preparing for Access
3
IP Addressing
The XWR-600 default LAN IP address is 192.168.0.1. The DHCP server on the
XWR-600 is configured by default to create a 192.168.0.x network.
Both the default LAN IP address and subnet scheme can be changed. However
for hassle-free plug-and-play installation of other Luxul hardware, we recommend you use the default IP address if possible.
If your client device is set to obtain an address automatically, no further
configuration is required and you can skip to the next step, Access and Setup.
If your computer or device isn’t set to obtain an IP address automatically,
you’ll need to set a temporary static IP address on that device. Set the IP
address of your computer to an address in the 192.168.0.X range, then set
the Gateway/Router address to 192.168.0.1 (the default IP address of the
XWR-600).
n Note: Visit http://luxul.com/ip-addressing to learn more about
changing your computer’s IP address and getting connected.
Access and Setup
4
Getting Connected
Connecting Via an Ethernet Device: Use an Ethernet cable to connect
your computer to one of the green XWR-600 LAN ports. Ethernet is the
preferred method of connection.
Connecting Via a Wireless Device: Connect a wireless client device
to one of the XWR-600 default wireless networks (Luxul600 or
Luxul6005G). Both Wireless networks will run in Open Security mode, so
a passphrase will not be required until Wireless Security is configured.
Open a web browser, enter 192.168.0.1, then log in to the router using the
default user name and password and proceed with configuration:
Default IP: 192.168.0.1
Username: admin
Password: admin
n NOTE: If another device on your network shares the 192.168.0.1
address, you’ll need to reassign that device a different IP
address to configure the XWR-600.
n NOTE: Only devices that support the 5GHz frequency will see the
default Luxul6005G wireless network.
Hardware Operation
5
XWR-600 Front Panel LED Indicators
Indicator Name Status Function
For future or custom design
considerations.
5GHz ON Indicates a 5GHz wireless network
is broadcasting.
2.4GHz ON Indicates a 2.4GHz network is
broadcasting.
1-4 LED ON Indicates a device is connected to
the Ethernet port number.
FLASHING indicates data packets are being
transmitted to the connected
device.
Internet
LED
ON Indicates the XWR-600 is
connected to the ISP.
FLASHING Indicates data packets are being
transmitted
Indicator Name Status Function
USB LED ON Indicates a USB enabled device is
connected and configured.
Power
LED
ON ON indicates power is applied to
the XWR-600.
FLASHING A flashing “heartbeat” indicates the
XWR-600 is operating normally.
OFF Indicates power is not applied to
the XWR-600.
Front Panel
XWR-600 Front Panel View
Rear Panel
XWR-600 Rear Panel View
Power Input: Power adapter included
n NOTE: To reboot the router, remove the power adapter, wait 10 seconds
and re-connect the power adapter.
WAN Port: 1 Black RJ-45 Ethernet Port for Internet connection
LAN 1 - 4 Ports: 4 Green RJ-45 Ethernet ports for connecting to the
local network
n NOTE: A Luxul switch is recommended in conjunction with the XWR-
600 to increase the number of local ports available.
Reset Button: Used to restore factory default settings.
c CAUTION: Holding the Reset button longer than 10 seconds will
result in a factory reset
To restore factory defaults, press and hold the Reset button until the
System LED stops flashing (approximatly 20 seconds). A factory reset
will take one minute or more to complete. A successful factory reset is
indicated when all of the Port LEDs flash once. When the System LED
starts flashing again, the unit is ready.
c CAUTION: Resetting the XWR-600 to factory defaults will remove
all custom settings.
Side Panel
XWR-600 Side Panel View
USB Port: 1 USB 2.0 port for future expansion.
LEGAL AND REGULATORY INFORMATION
© 2016 Luxul. All Rights Reserved.
No part of this publication, or any other publication may be modified or adapt-
ed in any way, for any purposes without permission in writing from Luxul. The
material in this manual is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design.
No license is granted, either expressly or by implication or otherwise under any
Luxul intellectual property rights. An implied license only exists for equipment,
circuits and subsystems contained in this or any Luxul product.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC ID: W59XWR-600
IC: 8584A-XWR-600
FCC Statement—Wireless FCC 2.4GHz & 5GHz 802.11abgn
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020,
declares that this Luxul XWR-600 is in compliance with the essential
requirements and other relevant provisions of Directive 1995/5/EC.
For a copy of this report send a self addressed stamped envelope
to: Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Industry Canada (RSS-Gen Issue 4)
CAN ICES-3(B)/NMB-3(B)
Sales
P: 801-822-5450
E: sales@luxul.com
© 2016 Luxul. All Rights Reserved. LUX-QIG-XWR-600 0161609
Technical Support
P: 801-822-5450 Option 3
E: support@luxul.com
Loading...