Simply Connected
User Guide
XWR-600
Dual-Band Wireless 600N Router
Use the XWR-600 to:
Provide an Affordable Concurrent Dual-Band
Wi-Fi Network
Combine High Performance Gigabit and
802.11n Wireless Functionality
Minimize Wireless Interference and Maximize
Data Rates
Create a Secure Guest Network
XWR-600
User Guide
Model Number: XWR-600
Dual-Band Wireless 600N Router
FCC ID: W59XWR600
IC: 8584A-XWR600
© 2014 Luxul. All Rights Reserved.
No part of this publication may be modified or adapted in any way, for any purposes
without permission in writing from Luxul. The material in this manual is subject to change
without notice. Luxul reserves the right to make changes to any product to improve
reliability, function, or design. No license is granted, either expressly or by implication or
otherwise under any Luxul intellectual property rights. An implied license only exists for
equipment, circuits and subsystems contained in this or any Luxul product.
This product is covered by one or more U.S. and foreign patents.
Patents: 7,379,717, 6,606,075, 6,373,448, other patents pending
DOCUMENT CONVENTIONS
The following graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data loss or
WARNING!: Indicates a condition or procedure that could result in personal
equipment malfunction.
injury or equipment damage.
CONTACT LUXUL
Sales
P: 801-822-5450
E: sales@luxul.com
Technical Support
P: 801-822-5450
E: support@luxul.com
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
2
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-UG-XWR-600 Vers: 07814
User Guide
CONTENTS
1 PRODUCT OVERVIEW 4
1.1 Product Introduction 4
1.2 Product Features 4
1.3 Product Specifications 4
1.4 Package Contents 5
2 HARDWARE DESCRIPTION AND INSTALLATION 5
2.1 Panel Layout 5
2.2 System Requirements 7
2.3 Installation Requirements 7
2.4 XWR-1750 Installation 8
2.5 Default IP Address 8
2.6 Connecting a Client Device 8
2.7 Verifying Connectivity 8
3 CONFIGURATION 9
3.1 Quick Setup 9
3.2 Status 16
3.3 Network 19
3.4 Wireless 24
3.5 Guest Network 30
3.6 Firewall/Security 32
3.7 QoS 36
3.8 VPN 38
3.9 Administration 40
3.10 Tools 47
4 REGULATORY COMPLIANCE 48
APPENDIX 1: COMMON COMMANDS 52
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
3
XWR-600
1 PRODUCT OVERVIEW
1.1 Product Introduction
The Luxul XWR-600 Wireless Router is a feature rich network device designed to
enhance the performance, security and reliability of a home or commercial network.
It enables simple monitoring, management and control of network usage to boost
effi ciency, reduce network bandwidth and minimize security risks. With web-based
management tools; along with advanced security, VPN, and bandwidth control features,
the XWR-600 provides the ideal foundation upon which to build your Luxul network.
1.2 Product Features
Complies with IEEE802.3, IEEE802.3u, IEEE802.3x, IEEE802.11a, IEEE802.11b, IEEE802.11g,
IEEE802.11n
One 10/100/1000M auto-negotiating WAN interface
Four 10/100/1000M auto-negotiating LAN interfaces
Protocol Support for TCP/IP, UDP, VPN, DHCP, NAT, SMTP, DNS, FTP
True QOS support to prioritize traffi c by Host, Protocol and Port
533MHz processor and powerful NAT forwarding features support up to 39K+
concurrent sessions
Support for Port Forwarding, DMZ hosts and ALG applications
Supports Dynamic Domain Name System or DDNS
Provides system security logs and fl ow statistics
Built-in DHCP server with static address lease capability
1.3 Product Specifi cations
Supported Protocols and
Standards
4
IEEE802.3, IEEE802.3u, IEEE802.3x, IEEE802.11a,
IEEE802.11b, IEEE802.11g, IEEE802.11n, TCP/IP, DHCP,
ICMP, NAT, PPPoE, SNTP, HTTP, DNS, ARP
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-UG-XWR-600 Vers: 07814
User Guide
Network Media
10Base-T: Cat5 or better 100Base-TX: Cat5 or better
1000Base-TX: Cat5 or better (Cat6 recommended)
Wireless 802.11a/b/g/n/ac adapter
Dimensions LxWxH in. (mm)
Power and Consumption
6.76”x4.38”x1” (171.6x111.2x25.5)
AC 110V 60Hz or 220V 50Hz Consumption:
1.4 Package Contents
The following items are included in the box:
XWR-600 Wireless Router
Power Cord
Quick Installation Guide
If any of the listed items are missing or damaged, please contact the reseller from
whom you purchased for return/replacement.
2 HARDWARE DESCRIPTION AND INSTALLATION
2.1 Panel Layout
2.1.1 Front Panel
XWR-600 Front Panel
LED Indicators:
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
5
XWR-600
Indicator Description Function
WPS LED ON Indicates the XWR-600 is ready for
WPS pairing.
5GHz FLASHING Indicates the XWR-600 is passing 5GHz
wireless data.
ON Indicates a 5GHz wireless network is
confi gured and broadcasting.
OFF Indicates there is no 5GHz wireless network
confi gured or the 5GHz radio is disabled.
2.4GHz FLASHING Indicates the XWR-600 is passing 2.4GHz
wireless data.
ON Indicates a 2.4GHz wireless network is
confi gured and broadcasting.
OFF Indicates there is no 2.4GHz wireless network
confi gured or the 2.4GHz radio is disabled.
1-4 LAN LED ON Indicates a device is connected to the
Ethernet port number.
FLASHING Indicates data packets are being transmitted
to the connected device.
Internet
LED
USB LED ON Indicates a USB enabled device is connected
Power LED ON Indicates power is applied to the XWR-600.
ON Indicates the XWR-600 is connected to
the ISP.
FLASHING Indicates data packets are being transmitted
to the Internet
and confi gured.
OFF Indicates power is not applied to the
XWR-600.
NOTE: It is recommended that a Luxul switch be used in conjunction with
6
the XWR-600 to increase number of local ports available.
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-UG-XWR-600 Vers: 07814
User Guide
2.1.2 Rear Panel
1. Antenna: 2 attached Antennas for connecting 2.4/5GHz wireless devices.
2. Power: Power port used to connect the provided DC power supply.
3. WAN: 1 WAN RJ-45 Ethernet Port for connecting internet feed.
4. LAN: 4 LAN RJ-45 Ethernet Ports allowing for four local network connections.
5. Reset Button: Used for hard reset or factory default reset. To hard reset the router,
press and release the button. To reset to factory defaults, press and hold this button
for 15 seconds.
CAUTION: Resetting the XWR-600 to factory defaults will remove all
CAUTION: Power Input: Please use the included power cable
custom settings
XWR-600 Rear Panel
2.2 System Requirements
Network Connections: 802.3 Ethernet Enabled Computer or 802.11a/b/g/n Wireless
Enabled Computer
Web Browsers: Supported Web browser versions include I.E. 9, Firefox 25, Safari 5,
Chrome 30, and up. The Web browser is used to confi gure the XWR-600.
Internet: Broadband Internet Service (depending on the service provider, a separate
modem may be required)
2.3 Installation Requirements
Install the XWR-600 in a stable/safe place to avoid any possible damage
Inspect the DC power adapter to ensure that it is correctly connected and
undamaged
To avoid electric shock, DO NOT open the XWR-600 housing (no user serviceable
parts inside). Opening the XWR-600 will void your warranty.
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
7
XWR-600
It is recommended that the Grounding connection to the outlet is functioning
properly and the XWR-600 is positioned away from direct sun light
Ensure there is sufficient space around the XWR-600 for proper ventilation and heat
dissipation. It is recommended to have at least 4-6 inches around all sides.
2.4 XWR-600 Installation
Before installing the XWR-600, test the Internet connection to validate that it is functioning properly. When Internet access has been confirmed, follow the steps below for
Router installation.
1. Connect the Internet cable to the XWR-600 WAN port
2. Connect one of the XWR-600 LAN port to a switch, access point, or computer.
3. Connect DC Power Adapter
4. Establish LAN or Wireless Connection
5. Connect a Wireless device to the 2.4GHz or 5GHz Wireless SSID.
2.5 Default IP Address
The XWR-600 default IP address is 192.168.0.1. This address can be changed. However,
for hassle free installation of other plug and play Luxul devices, it is recommended that
the default IP value be maintained.
2.6 Connecting a Client Device
Connect a client device to one of the XWR-600 LAN ports or to a switch that is
connected to an XWR-600 LAN port. Connect a wireless client device to one of the
wireless SSIDs (Luxul17502G or Luxul17505G). The DHCP server on the XWR-600 is
configured by default. If your client device is set to obtain an address automatically, no
further configuration is required.
2.7 Verifying Connectivity
After automatic configuration of the TCP/IP parameters, the ping command can be
used to check connectivity between the XWR-600 and the client device.
Windows Devices:
1. Select Start >> Run. Input cmd in the Run line then press enter.
2. At the newly opened command interface enter the following command: ping
192.168.0.1 and press enter. If connected properly, the system should report back a
result as follows: packets sent=4, packets received=4, packets lost=0. This means the
device is connected with a valid IP address.
8
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-UG-XWR-600 Vers: 07814
User Guide
3 CONFIGURATION
This chapter introduces the configuration of the XWR-600 Enterprise Multi-WAN
Router functions via the Web-based management interface.
Quick Setup
Status
Network
Wireless
Guest Network
Firewall/Security
Administration
Tools
3.1 Quick Setup
The Quick Setup page allows you to configure the Primary Internet / WAN connection
settings, the Local Network / LAN settings and the Primary 2.4GHz and 5GHz Wireless
Networks. This page is intended to get your Internet connection up and running as
quick and painless as possible.
3.1.1 Connection Type DHCP
This Connection Type option will automatically pull the WAN IP, WAN Subnet Mask,
WAN Gateway, WAN Primary DNS and WAN Secondary DNS from your ISP’s Modem.
Select the Menu Quick Setup and Connection Type DHCP from the dropdown to view
the following page:
Internet/WAN: Displays the WAN connection Options
w
Connection Type: Select the desired WAN Connection Type. When set to DHCP,
the Router will pull all connection information automatically from the ISP’s
Modem. DHCP is the default setting.
w
Primary DNS: Allows you to select the checkbox and manually configure a Primary
DNS Server IP Address. “DNS Assigned By ISP” is the default setting
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
9
XWR-600
w
Secondary DNS: Allows you to select the checkbox and manually configure a
Secondary DNS Server IP Address. “DNS Assigned By ISP” is the default setting
w
Custom MAC Address: Allows you to set a Custom MAC Address which allows
the Router to appear as a Computer to the ISP Modem. Some Modems will cache
the MAC Address of the first device used to setup Internet Service and cannot be
reset by the user. If this occurs you can clone that setup Device’s MAC Address to
allow the XWR-600 to connect to the Modem.
w
Custom MTU: Allows you to configure a Custom MTU setting. MTU (or Maximum
Transmission Unit), is the maximum packet size allowed on the network. Some ISPs
(usually DSL or Fiber) will require this value to be set if the Modem is in
Bridge mode.
After making any changes to the Connection Type, you must click the Save button
to Save your changes, then you must click the Reboot button for the changes to take
effect. You can click the Save button and proceed to other pages without losing your
configured changes.
3.1.2 Connection Type PPPOE
This Connection Type option requires a Username and Password that is provided by the
ISP and is typically used on Bridged DSL Modem connections. This type will automatically pull the WAN IP, WAN Subnet Mask, WAN Gateway, WAN Primary
DNS and WAN Secondary DNS from the ISP’s Modem once the Router is
successfully Authenticated.
Select the Menu Quick Setup and Connection Type PPPOE from the dropdown to
view the following page:
10
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-UG-XWR-600 Vers: 07814
User Guide
Internet/WAN: Displays the WAN connection Options
w
Connection Type: Select the desired WAN Connection Type. When set to
PPPOE, enter a Username and Password that the ISP provides to authenticate the
Router allowing it to connect. The Router will pull all connection information
automatically from the ISP’s Modem once it is successfully authenticated.
DHCP is the default setting.
w
Username: Allows you to enter the PPPOE Username specified by the ISP.
w
Password: Allows you to enter the PPPOE Password specified by the ISP.
w
Max Failed Pings: Allows you to specify the Maximum number of Failed Pings to
the PPPOE Server before the Router attempts to re-authenticate to the PPPOE
Sever. We recommend the default value of 3 attempts unless the ISP recommends
a different value.
w
Ping Interval: Allows you to specify the number of seconds to wait between Ping
attempts to the PPPOE Server. We recommend the default value of 5 seconds in
order to preserve WAN resources.
w
Primary DNS: Allows you to select the checkbox and manually configure a Primary
DNS Server IP Address. “DNS Assigned By ISP” is the default setting.
w
Secondary DNS: Allows you to select the checkbox and manually configure a
Secondary DNS Server IP Address. “DNS Assigned By ISP” is the default setting.
w
Custom MAC Address: Allows you to set a Custom MAC Address which allows
the Router to appear as a Computer to the ISP Modem. Some Modems will cache
the MAC Address of the first device used to setup Internet Service and cannot be
reset by the user. If this occurs you can clone that setup Device’s MAC Address to
allow the XWR-600 to connect to the Modem.
w
Custom MTU: Allows you to configure a Custom MTU setting. MTU (or Maximum
Transmission Unit), is the maximum packet size allowed on the network. Some ISPs
(usually DSL or Fiber) will require this value to be set if the Modem is in
Bridge mode.
After making any changes to the Connection Type, you must click the Save button
to Save your changes, then you must click the Reboot button for the changes to take
effect. You can click the Save button and proceed to other pages without losing your
configured changes.
3.1.3 Connection Type Static IP
This Connection Type option requires the Static IP, Netmask, Gateway, Primary DNS
and Secondary DNS provided by the ISP to be entered manually. This type will never
have a Dynamic IP Address change on the connection and is typically used in Business
or Remote Access implementations.
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
11
XWR-600
Select the Menu Quick Setup and Connection Type Static IP from the dropdown to
view the following page:
Internet/WAN: Displays the WAN connection Options
w
Connection Type: Select the desired WAN Connection Type. When set to
Static IP, you must enter the IP information that the ISP provides allowing the
Router to connect.
w
Static IP: Allows you to enter the WAN connection IP Address specified
by the ISP.
w
Netmask: Allows you to enter the WAN connection Subnet Mask specified
by the ISP.
w
Gateway: Allows you to enter the WAN connection Gateway IP Address specified
by your ISP.
w
Primary DNS: Allows you to manually configure the Primary DNS Server IP Address
specified by the ISP or any third party DNS Server IP Address. With the Static IP
Connection Type specified, this is a required field.
w
Secondary DNS: Allows you to manually configure the Primary DNS Server IP
Address specified by the ISP or any third party DNS Server IP Address. With the
Static IP Connection Type specified this is a required field.
w
Custom MAC Address: Allows you to set a Custom MAC Address which allows
the Router to appear as a Computer to the ISP Modem. Some Modems will cache
the MAC Address of the first device used to setup Internet Service and cannot be
reset by the user. If this occurs you can clone that setup Device’s MAC Address to
allow the XWR-600 to connect to the Modem.
12
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-UG-XWR-600 Vers: 07814
User Guide
w
Custom MTU: Allows you to configure a Custom MTU setting. MTU (or Maximum
Transmission Unit), is the maximum packet size allowed on the network. Some ISPs
(usually DSL or Fiber) will require this value to be set if the Modem is in
Bridge mode.
After making any changes to the Connection Type, you must click the Save button
to Save your changes, then you must click the Reboot button for the changes to take
effect. You can click the Save button and proceed to other pages without losing your
configured changes.
3.1.4 Local Network / LAN
Allows you to set the Local Network IP Address of the Router and the Subnet Mask
used in the Local Network.
Select the Menu Quick Setup to view the following page:
Local Network / LAN: Displays the Local Network IP Options
w
LAN IP Address: Allows you to configure the LAN IP of the Router, this will be used
by all devices in the LAN as the Default Gateway. If you are installing other Luxul
devices, we recommend keeping the default IP of 192.168.0.1.
w
LAN Subnet Mask: Allows you to specify the Subnet Mask to be used in the LAN.
The default value of 255.255.255.0 is recommended unless specified otherwise by
your Network Administrator.
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
13
XWR-600
3.1.5 Wireless Settings 2.4GHz Frequency
Allows you to configure the Primary 2.4GHz Wireless Network.
Select the Menu Quick Setup to view the following page:
Wireless Settings 2.4GHz Frequency: Displays the 2.4GHz Wireless
Network settings.
w
Operating Mode: Allows you to select the Operating Mode of the SSID. Access
Point is the default setting.
w
Network Name (SSID): Allows you to specify the Network Name (SSID) used to
identify the Wireless Network to client devices.
w
Security Mode: Allows you to set the desired Security Mode used to connect to
the SSID, the supported modes include 64bit/128bit WEP, WPA, WPA2 and WPA/
WPA2 Mixed. Open is the default setting, we strongly recommend adding Security
to any SSID.
w
WEP Key: When selecting WEP Security a new option will appear WEP Key. This
allows you to set the WEP Key, it can consist of Numbers 0-9 and Letters A-F. For
64bit WEP enter 10 hexadecimal digits (0-9 and A-F) or 5 regular characters. For
128bit WEP enter 26 hexadecimal digits (0-9 and A-F) or 13 regular characters.
w
Encryption: When selecting WPA or WPA2 security two new options will appear
the first is Encryption. This allows you to set the Encryption type used by WPA/
WPA2 the options include AES, TKIP&AES and TKIP. AES is the default and recommended setting.
w
WPA Passphrase: When selecting WPA or WPA2 security two new options will
appear the second is WPA Passphrase. This allows you to set the Passphrase used
to connect to the SSID. WPA Passphrases must be a minimum of 8 to a maximum
of 63 Characters and can contain Letters (capitol and lowercase), Numbers, Special
Characters and Spaces.
w
Channel: Allows you to specify the Channel used by the 2.4GHz Radio in the
Router, the supported Channels include 1-11 (non-overlapping channels are 1, 6 and
11). 6 is the default setting.
14
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-UG-XWR-600 Vers: 07814
User Guide
3.1.6 Wireless Settings 5GHz Frequency
Allows you to configure the Primary 5GHz Wireless Network.
Select the Menu Quick Setup to view the following page:
Wireless Settings 5GHz Frequency: Displays the 5GHz Wireless Network settings.
w
Operating Mode: Allows you to select the Operating Mode of the SSID. Access
Point is the default setting.
w
Network Name (SSID): Allows you to specify the Network Name (SSID) used to
identify the Wireless Network to client devices.
w
Security Mode: Allows you to set the desired Security Mode used to connect to
the SSID, the supported modes include 64bit/128bit WEP, WPA, WPA2 and WPA/
WPA2 Mixed. Open is the default setting, we strongly recommend adding Security
to any SSID.
w
WEP Key: When selecting WEP Security a new option will appear WEP Key. This
allows you to set the WEP Key, it can consist of Numbers 0-9 and Letters A-F. For
64bit WEP enter 10 hexadecimal digits (0-9 and A-F) or 5 regular characters. For
128bit WEP enter 26 hexadecimal digits (0-9 and A-F) or 13 regular characters.
w
Encryption: When selecting WPA or WPA2 security two new options will appear
the first is Encryption. This allows you to set the Encryption type used by WPA/
WPA2 the options include AES, TKIP&AES and TKIP. AES is the default and recommended setting.
w
WPA Passphrase: When selecting WPA or WPA2 security two new options will
appear the second is WPA Passphrase. This allows you to set the Passphrase used
to connect to the SSID. WPA Passphrases must be a minimum of 8 to a maximum
of 63 Characters and can contain Letters (capitol and lowercase), Numbers, Special
Characters and Spaces.
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
15
Loading...