Simply Connected
Quick Install Guide
XMS-1024P
24-Port Gigabit Ethernet
Managed PoE Switch
Use the XMS-1024P to:
Cost-effectively Add 802.3af/at PoE Capability to Your
Network
Deliver Power and Data for up to 24 PoE-Enabled Network
Devices with a Maximum Output of 320 Watts
Simplify PoE Device Installation, Including IP Sercurity
Cameras, VoIP Devices, and Wireless AP’s
Future Proof Your Network with Gigabit Speeds
(10X Performance of Fast Ethernet)
Optimize and Protect Your Network with Advanced
VLAN, QoS and Network Security Features
XMS-1024P
Quick Install Guide
Quick Install Guide
Model Number: XMS-1024P
24-Port Gigabit Ethernet Managed PoE Switch
© 2014 Luxul. All Rights Reserved.
No part of this publication may be modifi ed or adapted in any way, for any
purposes without permission in writing from Luxul. The material in this manual
is subject to change without notice. Luxul reserves the right to make changes to
any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights.
An implied license only exists for equipment, circuits and subsystems contained in
this or any Luxul product.
DOCUMENT CONVENTIONS
These graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that could result in
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CONTACT LUXUL
Sales
P: 801-822-5450
E: sales@luxul.com
2
Technical Support
P: 801-822-5450
E: support@luxul.com
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XMS-1024P 093140913
Simply Connected
PACKAGE CONTENTS
The following items are included in the box:
XMS-1024P 24-Port Gigabit Ethernet Managed PoE Switch
Power Cord
Two L-shaped rack mounting brackets and screws
Four rubber pads
Quick Installation Guide
RJ45 to Serial Console Cable
If any of the listed items are missing or damaged, please contact the Distributor
from whom you purchased for return/replacement.
HARDWARE DESCRIPTION
Front Panel
The front panel of the XMS-1024P Switch includes 1 console port, 24 1000Mbps
RJ45 and 4 shared SFP expansion ports, as well as LED indicators for each port. Each
1000Mbps port has one Link/Activity/PoE LED. A push button switch with an LED
indicator switches the display between Link/Activity and PoE.
XMS-1024P Front Panel View
LED Indicators
Each port has one Link/Activity/PoE LED. A push button switch with LED indicator
switches the display between Link/Activity and PoE.
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
3
XMS-1024P
Quick Install Guide
LED Indicators
LED indicators show the working status of the switch. The following table describes the LED functionality:
Indicator
Name
Power
System
Speed/PoE
Button
Speed
PoE
PoE Max
Description
On This LED indicates that there is power to the XMS-1024P
Off If LED is off, check the power connection on the back of the unit.
Flashing Indicates that the XMS-1024P is running normally.
On Indicates a malfunction. Contact technical support.
Off Indicates that the XMS-1024P is in startup and initialization
process or is not on.
Speed On Port LED’s display Speed status
PoE On Port LED’s display PoE status
Green The Link/Activity LED of the port will be on if there is a
1000Mbps device connected to the port.
Yellow The Link/Activity LED of the port will be on if there is a
10/100Mbps device connected to the port.
Flashing The Link/Activity LED flashes when a port is receiving
or transmitting data.
Off There is nothing connected to the port.
On Connected device is receiving PoE Power.
Off Connected device is not receiving PoE power.
Green Power being supplied within PD Specified limits
Yellow Power exceeds PD Specified limits
Yellow
Flashing
On The remaining PoE power is ≤7W.
PoE Fault( i.e. problem with Ethernet cable or PoE device).
Flashing The remaining PoE power is ≤ 7W after 2 minutes the LED will
remain on.
Off The remaining PoE power ≥ 7W.
At startup, port LEDs will flash for 1 second as a self test.
When an SFP optical interface is in use, the Link/Activity LED of the corresponding Ethernet
port will indicate the SFP status.
4
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XMS-1024P 093140913
Simply Connected
100-240V-50/60Hz 5.0A
Rear Panel
XMS-1024P Rear Panel View
Power Input: Please use the included power cable
PREPARING FOR INSTALLATION
System Requirements
Ethernet Cables to connect the XMS-1024P to Ethernet enabled devices
Computer equipped with a Web browser. Supported Web browser versions
include Microsoft I.E. 9.0, Firefox 3.6, Safari 5.0, Chrome 6.0, Opera 10.6 and up.
The Web browser is used to configure the XMS-1024P.
Power must be AC 100-240V~ 5.0A(Max) 50/60Hz.
Before Connecting to the Network
The XMS-1024P can be rack-mounted or used as a desktop switch. Before connecting to the network, please be aware of the following requirements:
Install the XMS-1024P in a stable/safe place to avoid any possible damage
Make sure there is space around the XMS-1024P for adequate ventilation and proper
heat dissipation. It is recommended to have at least 4-6 inches around all sides.
Do not place heavy articles on the XMS-1024P.
Power outlets should be within 5 feet of the XMS-1024P.
Verify the ground connection of the outlet is functioning properly.
Check the power cord to confirm a secure connection.
Avoid placement in direct sunlight.
When installing the XMS-1024P on a flat surface, attach the rubber feet to the
bottom of the device to avoid scratching the surface.
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
5
XMS-1024P
Quick Install Guide
XMS-1024P INSTALLATION
Installing the XMS-1024P in a Rack
The XMS-1024P can easily be installed in a standard 19” rack. The XMS-1024P includes
two mounting ears for installing and stabilizing the switch. For attaching the mounting
ears and installing the switch within a rack, please refer to the following illustration:
Rack-Mounting the XMS-1024P
Using the included screws, attach the mounting ears to each side of the switch.
Mount the switch in the rack with the LEDs facing outwards. Be sure the switch is
level and properly secured within the rack.
Desktop Setup
For use as a desktop device, position and apply the included rubber feet to the
bottom of the XMS-1024P.
Attaching the Rubber Feet to the XMS-1024P
Network Connections:
The XMS-1024P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/fullduplex mode and 1000 Mbps full-duplex mode. All RJ-45 ports support Auto MDI/
MDIX and can be used as ordinary ports or as Uplink ports. Any RJ-45 port can be
used to connect the XMS-1024P to an Ethernet enabled device (including servers,
routers, and other switches) without a crossover cable.
The XMS-1024P offers 4 shared SFP optical module expansion ports. Once the
Gigabit SFP optical modules are inserted, these interfaces can support optical fi ber
cables to extend the Gigabit network—enabling the network to reach beyond the
300 foot limitation of twisted pair Ethernet.
6
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XMS-1024P 093140913
Simply Connected
For the RJ-45 ports, Category-5, super Category-5 or Category-6 unshielded twisted
pair (CAT5/CAT5e/CAT6 UTP) should be used.
NOTE: For best results, it is recommended that Category-6 shielded
Optical fi ber/cable should be selected based on the wavelength of the SFP
optical module to be used.
Make sure only one Uplink channel exists between switches or between the XMS1024P and a router. Otherwise, loops can occur and result in network failure.
Default IP Address
The XMS-1024P default IP address is 192.168.0.4. This address can be changed.
However, for hassle free installation of other plug and play Luxul devices, it is
recommended that the default IP value be maintained.
Login
The XMS-1024P is not equipped with internal DHCP server. However, if your switch
is connected to a Luxul Router, confi guration will be automatic. Otherwise, the
IP address of the computer for login and confi guration will need to be manually
confi gured. The table below lists the default parameters of the XMS-1024P.
twisted pair be used to ensure stable data transmission at 1000 Mbps.
Parameter: Default Value
Default IP address:
Default user name:
Default password:
192.168.0.4
admin
admin
Login to the switch with the following steps:
1. Plug an Ethernet cable into any of the ports of the switch
2. Plug the other end into the Ethernet port of your computer
3. Power on the switch
4. Check to see that the IP address of the computer is within this network
segment: 192.168.0.xxx (“xxx” ranges 1~254). For example, 192.168.0.100.
5. Open the Web browser, and enter 192.168.0.4. The login window appears.
6. Enter the user name and password (default user name and default password
are both set as “admin”), and then click “OK” to login to the switch
confi guration window.
© 2014 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
7
ADVANCED SETTINGS
For login and advanced settings information go to luxul.com
WARNINGS AND SAFETY INFORMATION
Verify that the electrical circuits have appropriate grounding and overload protection.
Attach only approved power cords to the device.
Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment
operation specifications.
The XMS-1024P is designed for indoor use only. DO NOT place this outdoors.
DO NOT install in or near hot or humid places, such as a kitchen or bathroom. Take care to minimize
exposure to excessive heat or moisture.
Small parts and plastic bags used for packaging may be harmful to small children. KEEP All
ACCESSORIES OUT OF THE REACH OF CHILDREN!
The XMS-1024P may become warm when in use for extended time periods. This is normal and is not a
malfunction. DO NOT install where it will be exposed to paper, cloth or other flammable materials.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment uses and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions may cause harmful interference to radio
communications. However; there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020, declares that
this Luxul XAP-1500 is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
For a copy of this report send a self addressed stamped envelope to:
Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Information on this document supersedes all previous versions. Products and documents
subject to change without notice. Products may be discontinued without notice.
LUX-QIG-XMS-1024P
093140913
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685
luxul.com | 801-822-5450
Loading...