Luxul XGS-1008P User Manual

Simply Connected
Quick Install Guide
XGS-1008P
8-Port Gigabit PoE/PoE+ Switch
Use the XGS-1008P to:
Cost-Effectively Add PoE/PoE+ Capability to Your Network
Deliver Power and Data for up to Eight PoE-Enabled Devices with a Total Power Budget of 125 Watts
Simplify PoE Device Installation, Including IP Security Cameras, VoIP Devices, and Wireless Aps
XGS-1008P
Quick Install Guide
Quick Install Guide
Model Number: XGS-1008P 8-Port Gigabit PoE/PoE+ Switch
© 2015 Luxul. All Rights Reserved.
No part of this publication may be modifi ed or adapted in any way, for any purposes without permission in writing from Luxul. The material in this manual is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design. No license is granted, either ex­pressly or by implication or otherwise under any Luxul intellectual property rights. An implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
DOCUMENT CONVENTIONS
The following graphical alerts are used to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data loss
WARNING!: Indicates a condition or procedure that could result in
or equipment malfunction.
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CONTACT LUXUL
Sales
P: 801-822-5450 E: sales@luxul.com
2
a: 14203 Minuteman Drive, Ste 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
Technical Support
P: 801-822-5450 E: support@luxul.com
LUX-QIG-XGS-1008P 029151044
Simply Connected
PACKAGE CONTENTS
The following items are included in the box:
XGS-1008P 8-Port Gigabit PoE/PoE+ Switch
Power Cord
Two L-shaped rack mounting brackets and screws
Four rubber pads
Quick Installation Guide
NOTE: If any of the listed items are missing or damaged, please contact
the reseller from whom you purchased for return/replacement.
HARDWARE DESCRIPTION
Front Panel
The front panel of the XGS-1008P includes eight 10/100/1000 RJ-45 ports as well as one power LED, eight speed indicator LED’s, eight Link/Activity LED’s, eight PoE Status LED’s and one PoE Max LED. These LED indicators show the operating status of the XGS-1008P. Please refer to the detailed description of these indicators in the Chart on page 3.
XGS-1008P Front Panel View
© 2015 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
3
XGS-1008P
Quick Install Guide
The following chart shows the LED indicators of the XGS-1008P along with an explanation of the indicator’s properties:
LED
Power
PoE Max
PoE Status
LINK/ACT
1000Mbps
Color Status Description
Green ON This indicator lights up when the XGS-1008P is
powered
OFF If this indicator is not lit, please check the power
cable to ensure proper connection to the outlet and the XGS-1008P.
ON (RED) The power of all the connected PoE ports is
between 118W and 125W. No power may be supplied if additional PDs are connected.
FLASHING (RED)
OFF The power of all the connected PoE ports is <118W,
Green ON There is a PoE PD connected to the port, which
FLASHING The PoE power circuit may be in short or the power
OFF No PD is connected to the corresponding port, or no
Green ON Indicates the port is connected to a device.
Blinking Indicates data activity on the port.
OFF Indicates the port is not connected to a device.
Green ON There is a 1000 Mbps device connected to the
OFF There is a 10/100Mbps device connected to the
The power of all the connected PoE ports is >=125W.
or there is no PD connected to the corresponding port.
supply power successfully.
current may be overloaded.
power is supplied according to the power limits of the port.
corresponding port.
corresponding port, or there is no device connected to the corresponding port.
PREPARING FOR INSTALLATION
System Requirements
Ethernet Cables to connect the XGS-1008P to Ethernet enabled devices
Power should be AC 100-240V~ 2.0A(Max) 50/60Hz.
4
a: 14203 Minuteman Drive, Ste 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XGS-1008P 029151044
Simply Connected
Installation Requirements
Install the XGS-1008P in a stable/safe place to avoid any possible damage
Inspect the AC power cord to ensure that it is correctly connected and undamaged
To avoid electric shock, DO NOT open the XGS-1008P housing (no user service­able parts inside). Opening the XGS-1008P will void your warranty.
It is recommended that the Grounding connection to the outlet is functioning properly and the XGS-1008P is positioned away from direct sun light
Ensure there is suffi cient space around the XGS-1008P for proper ventilation and heat dissipation. It is recommended to have at least 4-6 inches around all sides.
Before Connecting to the Network
Before connecting the XGS-1008P to the network, please check the following:
Determine placement location. Do not place any heavy articles on the XGS-1008P.
Ensure there is adequate space for proper heat dissipation and ventilation around the XGS-1008P.
Power socket should be within 4 feet of the XGS-1008P.
Check power cable to confi rm safe and secure connection.
XGS-1008P INSTALLATION
Installing the XGS-1008P in a Rack
The XGS-1008P can easily be installed in a standard 19” rack. The XGS-1008P includes two mounting ears for installing and stabilizing the switch. For attaching the mounting ears and installing the switch within a rack, please refer to the following illustration:
Rack-Mounting the XGS-1008P
© 2015 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
5
XGS-1008P
Using the included screws, attach the mounting ears to each side of
Quick Install Guide
the switch,.
Mount the switch in the rack with the LEDs facing outwards. Be sure the switch is level and properly secured within the rack.
Desktop Setup
For use as a desktop device, position and apply the included rubber feet to the bottom of the XGS-1008P.
Attaching the Rubber Feet to the XGS-1008P
Connecting Devices
Use standard Ethernet CAT5, CAT5e or CAT6 cable to connect the XGS-1008P to a device as described below. The XGS-1008P will automatically adjust to the charac­teristics (speed/duplex) of the device to which it is connected. The PoE function is autosensing. As long as the powered device is 802.3af/at compliant, the switch will provide power.
NOTE: Legacy PoE devices that need more than 30Watts can not be
6
powered by the switch
a: 14203 Minuteman Drive, Ste 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XGS-1008P 029151044
Simply Connected
Connecting the XGS-1008P to a Device
When a device is properly connected, the Link/ACT LED for each port lights up green. Please refer to the LED Indicators section for defi nitions and troubleshooting.
Connecting to a Router or Other Switch
Connecting the XGS-1008P to a Router and Devices
When a device is properly connected, the Link/ACT LED lights up green. Please refer
to the LED Indicators section for defi nitions and troubleshooting.
© 2015 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
7
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However; there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020, declares that this Luxul XGS-1008P is in compliance with the essential requirements and other relevant provisions of Directive 2006/95/EC.
For a copy of this report send a self addressed stamped envelope to: Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Industry Canada
CAN ICES-3(A)/NMB-3(A)
Information on this document supersedes all previous versions. Products and documents
subject to change without notice. Products may be discontinued without notice.
LUX-QIG-XGS-1008P 029151044
a: 14203 Minuteman Drive, Ste 201, Draper, UT 84020-1685
luxul.com | 801-822-5450
Loading...